Search Documents

By Stefan Larsson, Sadek Baker, Razvan Ignat

"This paper describes the execution of two full-scale field tests where a braced steel sheet pile wall interacting with rows of overlapping dry deep mixing columns was first excavated and then loaded to failure. The aim of the tests is to provide insight of the performance of dry deep mixing column rows located in passive zone and interacting with a retaining structure. The column rows were installed perpendicular to the sheet pile walls with two different area ratios, i.e. different distanced between the column rows. Both tests were extensively instrumented with inclinometers, pore pressure transducers, bellow-hoses, earth pressure gauges and strain gauges mounted on the struts. Results of the performedtests will serve as development of design methods for excavation support with columns.INTRODUCTIONDry deep mixing has been used with good results to strengthen the soil when excavations are to be performed in locations with thick soft clay deposits. An application that has increased in recent years is to install columns on the passive side of the retaining structure. Columns can be installed in different patterns but rows, grids or blocks are the most common arrangement. The use of column type ground improvement installed on the passive side of a retaining structure has been documented for a few field cases, Tanaka (1993), O’Rourke et al. (1997b), O’Rourke and McGinn (2006), Ou et al. (2008). By improving the soil on the passive zone, the passive earth pressure in front of the retaining structure is increased. This has proven to reduce the excavation induced deflections behind the retaining structure, reduce the structural forces (bending moment in the retaining structure, strut and anchor forces) and improve the safety against basal heave failure. The main focus of the conducted measurements within these cases has been on recording deflections and structural forces on the retaining structure and there is very little documentation available of the stress-strain behavior of the improved soil acting on the passive side of the retaining structure.Two full-scale tests of braced steel sheet pile walls interacting with rows of overlapping dry deep mixing columns were first excavated and then loaded to failure was conducted during the spring-summer of 2014. This paper briefly describes the test set up, instrumentation, test procedure and some selected results from one of the conducted tests."

Jan 1, 2015

By Chang-Yu Ou, Shao-Chi Chien, Hsuan-Hsiang Chang

"A field test was performed to investigate the applicability of electroosmosis with the injection of saline solution of Taipei silty clay. The calcium chloride solution and sodium silicate solution were used as the saline solution for the injection in this test. The results of this study indicate that injection using calcium chloride solution and sodium silicate solution during the electroosmosis to increase drained water from cathode and electro-chemical reaction can greatly improve the effect of electroosmosis and shorten the time of treatment. The results of field vane tests showed that the undrained shear strength after treatment increased an average of approximately 120% for a treatment period of 24 days.INTRODUCTIONThe first field application of electroosmosis in soil was demonstrated by Casagrande in 1939. Since then, more complete field applications of electroosmosis such as Bjerrum (1967), Fetzer (1967), and Lo et al. (1991b) have been made.The results of field electroosmotic work for a period of 120 days were presented by Bjerrum et al. ( 1967). The mean undrained shear strength, Su, increased from 18 to about 40 kPa, with a uniform surface settlement of about 0.5 m. Lo et al. (1991b), with a more sophisticated installation and a relatively larger spacing, also had positive results. For a 3 m electrode spacing during the treatment of a period of 33 days, the mean Su increased from 18 to about 25 kPa. Although the effect of the electroosmosis could be applied in the field based on the above examples, the response remained slow. For actual field work, the application of electroosmosis will be limited due to short project schedules and request of the effect of improvement."

Jan 1, 2005

By James J. Scott

Research and development has been carried out on the patented Dynamic Rock Anchor, tradenamed DYNA-ROK and DYNA-ROK PLUS Anchors, which are manufactured and marketed by Ingersoll-Rand Company. This paper will present the results of field testing of this revolutionary new concept in ground control. Geologic conditions will be described where the plastic sleeve of the DYWA-ROK anchor alone is sufficient to provide anchorage and also, where in softer ground conditions, the DYWA-ROK PLUS is applied. The rationale for making the decision as to the type of fixture to be employed, the length of plastic tube to be used and the quantity of resin are explained. Pull test data will be shown from eight different coal seams in the Eastern United States where the product has been installed.

Jan 1, 1990

By Jeffrey Johnson, Carl Sunderman, Ted Williams, Stephen Signer, Douglas Bayer

To measure the loading behavior of friction bolts, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) installed strain gauges on the interior of friction bolts and developed a battery-powered miniature data acquisition system (MIDAS) that fits inside the hollow portion of the friction bolt. The advantages of this system are that it is protected from face blasts and eliminates the need for external wiring. Laboratory pull-out tests showed that friction bolts installed in a concrete block with resin were loaded to about 1.8 tons/ft of bolt length; bolts installed without resin were loaded to 1.3 tons/ft. Three strain-gauged friction bolts were installed at Hecla Mining Company’s Gold Hunter Mine, Mullan, ID, in the wall or rib of a mechanized cut-and-fill stope. The object of these tests was to establish an installation procedure for the bolt-and-MIDAS combination and to evaluate performance. The stope was advanced in three 15-ft increments and strains induced in the rock bolts by stress changes in the rock were recorded every 30 minutes. The MIDAS proved to be rugged enough to withstand the shock and vibration from nearby (5 ft) face blasting. Data from MIDAS showed that the friction bolt installed with resin was the most sensitive to each face advance. It showed a steady increase in loading to a maximum value of 1000 microstrain. The friction bolt installed without resin showed stick-slip behavior with loads to a maximum of 400 microstrain before the stope was completed.

By Jeffrey Johnson

To measure the loading behavior of friction bolts, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) installed strain gauges on the interior of friction bolts and developed a battery-powered miniature data acquisition system (MIDAS) that fits inside the hollow portion of the friction bolt. The advantages of this system are that it is protected from face blasts and eliminates the need for external wiring. Laboratory pull-out tests showed that friction bolts installed in a concrete block with resin were loaded to about 1.8 tons/ft of bolt length; bolts installed without resin were loaded to 1.3 tons/ft. Three strain-gauged friction bolts were installed at Hecla Mining Company's Gold Hunter Mine, Mullan, ID, in the wall or rib of a mechanized cut-and-fill stope. The object of these tests was to establish an installation procedure for the bolt-and¬MIDAS combination and to evaluate performance. The stope was advanced in three 15-ft increments and strains induced in the rock bolts by stress changes in the rock were recorded every 30 minutes. The MIDAS proved to be rugged enough to withstand the shock and vibration from nearby (5 ft) face blasting. Data from MIDAS showed that the friction bolt installed with resin was the most sensitive to each face advance. It showed a steady increase in loading to a maximum value of 1000 microstrain. The friction bolt installed without resin showed stick-slip behavior with loads to a maximum of 400 microstrain before the stope was completed.

Jan 1, 2003

By H. Sahay

"DISCLAIMER NOTICEThe views and conclusions contained in this presentation are those of the author and should not be interpreted as necessarily representing the official policies or recommendations of the Department of Mines and Energy, Government of Newfoundland and Labrador. ABSTRACTThis paper describes the main testing procedures that should be carried out to evaluate the capacity and capability of the service brakes on the large-size diesel-electric trucks now in common use at open-pit mining operations. Brake testing programs in general are described, and then consideration is given to different techniques of service brake testing, brake performance evaluation, braking energy and typical performance characteristics.IntroductionThe first diesel-electric truck with a capacity of about 85 tons was introduced in 1963 by Unit Rig and Equipment Company of Tulsa in cooperation with General Electric Company, who successfully developed and supplied the most important component- motorized wheels. Since then, its popularity and numbers have continued to grow, and now more than 3700 such units are in operation in mines around the world. In Canada alone, their number is more than 700, including about 150 in the Province of Newfoundland and Labrador. Similarly, their size has also grown from that initial capacity of 85 tons to 350 tons.Although the introduction of the electric trucks proved to be invariably economical, their indiscriminate use was not without severe consequences. Many runaways and even fatalities occurred when the dynamic retarder failed while the truck was travelling loaded down severe grades. The service brakes in such cases proved incapable of stopping runaway trucks, mainly due to their limited capability and the fading caused by excessive heat produced during the act of braking itself. This eventually led the various governments, the open-pit operators and the manufacturers to seriously question the braking capability as well as function of both service brakes and dynamic retarders. Extensive testing"

Jan 1, 1980

By Joshua Hoffman, Braden Lusk, Kyle Perry

Despite its porous and lightweight characteristics, aluminum mesh is believed to have blast mitigation properties. The current use of the mesh includes fuel tanks for airplanes, boats, and fuel stations as well as light armored vehicles for the military. The mesh acts as an explosion suppressant by preventing fuel tanks from exploding when exposed to an ignition source. More recently, work has been performed to assess the ability of the mesh to mitigate blast pressures produced by high explosives.

Jan 1, 2009

By Todd Grounds, William R. Reed, VASU GANGRADE, Michael Shahan, Garron Ross, Kunal Singh

Roof bolter canopy air curtains (CACs) are gaining acceptance as a respirable dust control device that can provide roof bolter operators with protection from overexposure to respirable coal mine dust. Both lab and field studies on the effectiveness of roof bolter CACs have been published. Field studies have shown the effectiveness to be variable. However, in all previous field studies, none has been conducted when the roof bolting machine operates downwind of the continuous miner (CM)—a scenario for which the CAC was designed to provide respirable dust control. This study, performed by researchers from the National Institute for Occupational Safety and Health (NIOSH), was conducted to test a CAC on a roof bolter machine operating downwind of the CM. The results of testing demonstrated that the roof bolter CAC can effectively provide respirable dust protection for roof bolter operators with dust control efficiencies ranging from 11 to 40%.

Oct 14, 2020

By Bradley V. Johnson

The Bureau of Mines constructed a microminer--a scaled-down (5-by 5- by 11-foot) continuous-mining machine of the drum type with a unique triaxially controlled head--for use in a research program to study the effects of continuous-mining-machine parameters on the generation of respirable dust. This report describes field research with the microminer at the Bureau's Experimental Mine at Bruceton, Pa. Experiments were conducted to determine the effects of depth of cut, rotational speed, and sump and shear rates on the generation of respirable dust. The cutting forces were also monitored and compared with depth of cut. There appears to be a reduction in the amount of respirable dust generated when the depth of cut is increased or rotational is speed lowered, Variation of other machine parameters seems to have little effect on dust generation.

Jan 1, 1975

By Jeffrey A. Yonkey, Timothy J. Lutz, Jacob L. Carr, Christopher C. Jobes

"Since 1984, there have been 39 fatalities involving striking and pinning of the operator and other workers by the continuous mining machine (CMM). In January 2015, the U.S. Mine Safety and Health Administration (MSHA) finalized a regulation to require proximity detection systems on all continuous mining machines except full-face machines (MSHA, 2015). Proximity detection systems are designed to stop machine motion to protect miners from striking/pinning hazards. Several MSHAapproved proximity detection systems are commercially available.NIOSH researchers have been involved in the development and testing of proximity detection technology since creating the HASARD system (Schiffbauer, 2002) and have recently conducted research intended to develop more advanced proximity detection technology for CMMs (DuCarme et al. 2013; Jobes et al. 2012; Carr, DuCarme et al. 2013 and Carr, Li et al. 2013). In addition, NIOSH has also conducted research investigating how the signals of a proximity detection system propagate (Li, Carr et al. 2013 and Li, Jobes et al. 2012) and have developed a novel method for determining the location of a personal wearable device (PWD) relative to the magnetic field generators (Carr et al. 2010 and Jobes, et al. 2012).To evaluate the performance of proximity detection systems implemented in industry, NIOSH researchers conducted tests in 2013 on three systems installed on CMMs at three underground mines in Illinois and West Virginia. The results of these tests indicated that, while generally consistent performance was observed, there were opportunities for improving performance. These results were presented at the 2014 SME Annual Meeting (Carr, Lutz, et al. 2014). Since that time, second-generation systems have become available to the industry and are becoming more commonly used.Beginning in early 2014, NIOSH researchers conducted underground testing of these secondgeneration proximity detection systems installed on CMMs. Five tests were conducted on four installations of second-generation proximity detection systems, with one installation being tested twice. The tests were conducted at mines located in Illinois, Virginia and Kentucky with seam heights ranging from 137 cm (54 in.) to 213 cm (84 in.). These tests were conducted using the same test protocol used during first-generation testing, which is summarized in the following section."

Jan 1, 2014

By Han Jie

The results of full scale plate load tests on stone columns on soft clay in coastal areas are presented in this paper. Four load tests were made, two of which were performed on the ground treated with stone columns, one on an isolated stone column and the last one on the untreated ground. For a given stress range, the settlement of the rigid plate, the stress concentration factor, and the excess pore water pressure were measured. It is found that the distribution of vertical stress beneath the rigid plate supported by the composite ground of stone columns is very different in shape from the one by the untreated ground, that the stress concentration factor has a relation with the stress level and time, that the stone columns increase the bearing capacity up to by 2 times, and that the ground stabilized by stone columns is of great advantage to keep the foundation stable.

Jan 1, 1991

By Garnsey R. G T, Wenk G. J, Toop A, Sowerby B. D

A bulk mineral analyser (BMA) suitable for the determination of Cu or Ni in bulk ore samples has been developed at the Lucas Heights Research Laboratories. This analyser, which uses the nuclear resonance scattering technique, is highly specific to the wanted element. The technique has previously been extensively field tested for copper at Mount Isa, Queensland.The present paper discusses the field trial in 1982 of a commercial prototype BMA for nickel. The trial was undertaken at the lateritic nickel mine at Greenvale, Queensland. The BMA and its shielding, together with a laboratory spectrum analyser, were sited in the sample shed adjacent to the workings. Two hundred and thirty-eight ore samples taken directly from the mine blastholes were assayed by the BMA. The average mass of sample was 12 kg, metal contents varied from 0.2 to 3.5 wt/per cent Ni and 4 to 43 wt/per cent Fe and free moisture varied from 11 to 55 wt/per cent. A measurement took 10 min to complete, although this time could have been reduced at the higher nickel grades. The r.m.s. deviation between BMA and chemical assays was 0.09 wt/per cent nickel. Iron and bulk density were also determined by the BMA, r.m.s. deviations being 1.7 wt/per cent and 0.03 g/cmJ respectively. Similar results could be expected from a BMA in routine industrial use at other nickel mines.

Jan 1, 1983

By Ziyad Abunada, David O’Connor, Abir Al-Tabbaa

"Abstract Contaminated land remediation using soil mix technology (SMT) is a relatively recent development which has been shown to be a cost effective and versatile system with numerous environmental advantages over other remediation techniques. The added complexities and variability associated with contaminated sites has escalated the need for field trials, field monitoring and specific QC measures to be undertaken for this setting and was the rationale behind project SMiRT (Soil Mix Remediation Technology). The main aim of project SMiRT was field validation, testing and assessment to provide stakeholder confidence in SMT and increase its uptake for land remediation in the UK. The field trials involved the treatment of 800 m3 of soil, through applying six different remediation techniques with four different SMT systems and introducing over thirty binders and binder compositions with a range of installation methodologies. Various issues were faced during the installation process and which were addressed on site. This paper presents some aspects of early age field observations, field monitoring, in-situ testing, coring and laboratory testing of cored samples and highlights some lessons learnt, providing valuable information on the issues that need to be addressed for this application of SMT.IntroductionAlthough soil mix technology (SMT) was developed in the 1960s in Japan and Sweden for geotechnical applications, its potential in geo-environmental applications became evident more recently the 1980s in the US and in the 1990s in Europe, having since increased to provide a range of remediation systems (Al-Tabbaa and Evans, 2003; Al-Tabbaa et al., 2011). The most common applications to date have been (a) the construction of low permeability containment walls or cut-off walls to contain a contaminated site; (b) stabilisation/solidification (S/S) treatment, with cementitious binders, for physical and chemical encapsulation of contaminants in soils and (c) the installation of permeable reactive barriers (RPBs), which are permeable walls that intercept the groundwater flow and remove contaminants from it, by mixing special additives with the native soil. Contaminated land remediation using SMT is a cost effective and versatile approach with numerous technical and environmental advantages over other remediation techniques. These advantages include the use of simple and well established techniques and equipment, speedy implementation, applicability to sites of any size and to multiple contaminants, elimination of off-site disposal, low risk and low emissions. There is a lack of competing alternative technologies that offer the same level of versatility and economic, environmental and social benefits, under current environmental legislation constraints. In addition, most currently available contaminated land remediation techniques are only partially effective, and are relatively contaminant-specific. This makes SMT a promising and timely contender to lead the market place in offering a cost-effective, efficient and low risk solution to contaminated soil and groundwater remediation and has resulted in a range of recent innovations."

Jan 1, 2014

By Michael J. Beus

The National Institute of Occupational Safety and Health-Spokane Research Laboratory (NIOSH-SRL) have developed a Shaft Conveyance Monitoring System (SCMS). Assessment of current hoisting technology has shown that monitoring wire rope tension and conveyance position and load directly from the skip or cage top offers several significant safety, production, and maintenance advantages. The SCMS consists of conveyance position and guide displacement sensors, a battery power supply and charging system, and a new sensor to measure hoist rope tension. This device provides a warning of the occurrence of ?slack rope? a particularly dangerous condition. A 2.4 GHz radio link transmits data to the hoistroom. A reduced scale hoisting test facility has been constructed to test these components prior to field trials. The advantages of monitoring wire rope tension and conveyance position and load directly from a skip or cage top will be discussed. Field tests are underway in full-size shafts to refine the concept and evaluate long-term reliability and maintenance requirements. Application of this technology may result in decreased maintenance costs as well as safer, more productive hoisting operations.

May 1, 2001

By L. Zhou, L. Yuan, D. Bahrami

Underground mine fires remain a concern for mine operators, posing a health and safety risk to mineworkers. In the last decade, the number of mine fires has decreased significantly; however, dealing with an unknown fire in underground mines can be a challenging task, which could lead to a hazardous condition for miners during an evacuation and rescue operation. A timely detection of a mine fire and monitoring its characteristics, namely size and location, are of great importance in reducing the risk of mine fire injuries. A new improved fire location algorithm has been developed and integrated into an Atmospheric Monitoring System (AMS) program by researchers from the National Institute for Occupational Safety and Health (NIOSH). This paper describes the new fire location model and presents the results of verification fire tests conducted at the Safety Research Coal Mine (SRCM) facility of the Pittsburgh Mining Research Division (PMRD) using the collected AMS data. NIOSH is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions in mines. The results demonstrate successful application of the improved fire location model and provide a useful tool for solving the problem of unknown fire location and reducing the risk of hazardous conditions.

Sep 29, 2020

By Anthony T. Iannacchione

The Roof Fall Risk Index (RFRI) is a new method introduced by the National Institute for Occupational Safety and Health (NIOSH) to assist the underground stone mine operator in 1) assessing defects the mine strata and 2) rating the relative roof fall risk these defects pose. The RFRI utilizes observational techniques to identify defects in the roof strata caused by local geologic, stress, and mining conditions. Assessment values for ten defined defect categories provides the foundation for estimating a range of risk conditions between 0 and 100 that define the potential for a roof fall. This paper examines how the defect information is collected using two field verification sites and proposes methods to analyze the RFRI data. These examples provide information on how well the method replicates observed conditions and how it might be applied in practice.

Jan 1, 2006

By N Merry, T Cocks

The mineral exploration industry is increasingly aware of the importance of the relationship between mineralogical data and geochemical assay results. However, until recently, the cost and time constraints of most techniques for analysing alteration mineralogy have precluded detailed alteration studies. These impediments have been reduced by the development of the Portable Infrared Mineral Analyser (PIMA), a field portable infrared spectrometer that allows rapid (in field) and cost effective analysis of alteration minerals including subtle variations in mineral crystallinity and composition.   A major application of this technology is in mapping mineralogical variations within hydrothermal alteration systems. Using actual case study examples this paper introduces two approaches to using the PIMA data: 1. for directly mapping alteration systems and using the PIMA data to provide vectors to mineralisation, and 2. for establishing empirical relationships between geochemical data and PIMA spectral data. These applications demonstrate that this technology can be an invaluable tool for targeting and mapping alteration and mineralisation.

Jan 1, 1995

By Merry N, Cocks T

The mineral exploration industry is increasingly aware of the importance of the relationship between mineralogical data and geochemical assay results. However, until recently, the cost and time constraints of most techniques for analysing alteration mineralogy have precluded detailed alteration studies. These impediments have been reduced by the development of the Portable Infrared Mineral Analyser (PIMA), a field portable infrared spectrometer that allows rapid (in field) and cost effective analysis of alteration minerals including subtle variations in mineral crystallinity and Composition.

Jan 1, 1995

By S. Lohmeier, D. Gallhofer, B. G. Lottermoser

Reprocessing of historic gold tailings is a common activity in South Africa, while base metal tailings offer similar reprocessing potential. The historic base metal tailings of the Namib Pb–Zn mine (Erongo Region, Namibia) still contain valuable resources of Pb and Zn in carbonate-rich matter. Micro-analysis of primary ore minerals identifies some galena as argentiferous and sphalerite as the principal host of Cd. This study demonstrates that knowledge of primary ore mineralogy helps to reveal the hosts of valuable commodities (Ag, Cd) and that field-portable X-ray fluorescence tools allow precise and accurate determinations of major and minor elements like Zn and Cd in such carbonate-rich material. Although there are limitations to directly determine the contents of certain element (i.e., As, Sb, In), linear correlations allow prediction of the likely abundance of these elements. Providing that the inter-mineral and inter-element relations are understood and there is consistency in sampling and analytical methodology, portable X-ray fluorescence analysis is an effective method to evaluate the chemical characteristics of base metal tailings for a range of major and trace elements.

Sep 9, 2024

Twenty field-scale tests were conducted in a 28 MW pulverized coal power plant in Healy, Alaska, to examine mill power consumption in relation to coal grind size. The intent in this field-scale study was to verify if grind size truly impacted power consumption by a detectable amount. The regression model developed from the data indicates that grind size does impact mill power consumption, with finer grinds consuming significantly more power than coarser grinds. However, other factors such as coal hardness (i.e., the lower the Hardgrove Grindability Index, or the harder the coal, the higher the power consumption) and mill throughput (i.e., the higher the throughput, the higher the power consumption) had to be included before the impact of grind size could be isolated. It was also observed that combining amperage and flow rate into a single parameter, i.e., specific amperage, hurt modeling. Cost analysis based on the regression model indicate a power savings of $19,972 per year if the coal were ground to 50% passing 76 mm rather than the industry standard of 70% passing 76 mm. The study also demonstrated that size reduction constituted a significant portion of the power consumption.

Jan 1, 2008