Search Documents

By G. A. Beiswenger

The application of the law of supply and demand to the sale of crude oil is generally conceded, but the motives underlying the buyer's (refiner's) demands are not always obvious to the seller (producer). In some cases this obscurity has led to the conclusion that the refiner may be unnecessarily particular when he selects one crude and rejects another. This preference, however, is very largely the reflection of the refiner's product demands and the quality of the stocks obtainable from the selected crude. The purpose of this paper is to point out critical characteristics of the major classes of refined products and to show how crudes vary in their suitability for such products. With relatively few exceptions, available processing methods and addition agents make it theoretically possible to produce any type of refined product from any crude source, although it may not be economi-cally sound to do so. The widespread application of thermal cracking for converting higher boiling stocks into gasoline is well known. More recently cracking and refining in the presence of catalysts9 have been developed, as well as various processes for polymerizing lighter hydro-carbons into gasolines having desirable characteristics.6 For several years, selective solvents have been applied commercially to refining inferior quality kerosene, Diesel fuel and lubricating oil distillates .3 Improved methods for refining lubricating oils from crude residua,4 formerly suitable only for fuel, are now in use and a number of special solvent processes are available for dewaxing lubricating oils to low pour point.5 These improved refining methods have been developed not only to meet the demand for improved product quality but also to enable the refiner to obtain quality products from crude sources that would not yield such products by the older refining methods. In many cases, the utilization of these modern refining tools necessi-tates an appreciable expenditure for equipment as well as added manufac-turing costs, and their application therefore must be justified economically. Despite the availability of such tools, the added processing costs involved and yields obtainable may render their application entirely impractical. To illustrate this point, inspections of typical cuts from various crudes

Jan 1, 1940

By Parissa Mirjafari, Ron Martel, Susan A. Baldwin, Luke Moger

Mine drainage contains metals and sulfate, which may be toxic to aquatic life at certain concentrations and should be removed to acceptable levels before release of any drainage to the environment. One method for treating mine drainage is passive treatment, which is increasing in popularity due to lower construction and operating costs. This method is based on the activity of sulfate reducing bacteria (SRB) respiring on sulfate while using fermentation products from decomposing complex organic materials. The product of this biological process is hydrogen sulfide, which reacts with metals in mine drainage and precipitates them as metal sulfides. However, in practice passive treatment systems are not always effective, reducing the reliability of this approach. In this study, a mixture of hay, cow manure and wood chips was tested in continuous flow experiments for efficacy at sustainable treatment of sulfate and selenium containing water from a mine tailings pond. Factors that contributed to a decline in performance included lowering of the pH due to acids leaching out of the organics, re-oxidation of sulfide back to sulfate and a reduction in dissolved organic compounds over time. In this paper methods are described to overcome these problems so that treatment is made more reliable.

Jan 1, 2011

By L. M. Luckevich

Gypsum is a product from the neutralization of sulfuric acid by lime or limestone. This paper will discuss specifications for gypsum used in wallboard, cement and agriculture and the factors affecting its utilization potential. Process conditions during the neutralization which enhance or inhibit utilization potential will be included. In addition, this paper provides a technical and economic perspective of the gypsum industry in North America with a view to the factors affecting the utilization of synthetic gypsum in traditional applications. Current production and consumption of natural and synthetic gypsum in Nonh America are described and the impact of their differences on utilization options are discussed.

Jan 1, 1996

By W. J. S. Craigen, G. E. Wittur

"In the context of today's continuously changing world, there are many factors which must be considered when attempting to assess the ability of Canada's primary copper producers to remain competitive in the face of increasing competition in world markets. In this paper, we have attempted to document those factors that will have the greatest impact on the future viability of Canada's copper industry, and to suggest possible strategies to fully utilize whatever inherent advantages Canada may have to enhance its competitive position. Technological factors related to the efficiency of precious and by-product metals recovery, energy type and utilization efficiency, production and sale of sulphur by-products, and control of 502 emissions are given high priority in this evaluation of Canada's future needs to remain competitive. Particular emphasis is placed on assessing the relative viability of hydrometallurgical versus pyrometallurgical processes for copper; to address uniquely Canadian conditions and problems. Due consideration is also given to the economic incentives required to allow Canada's copper producers to compete under anticipated world market conditions and to facilitate the continued development of Canada's copper resources. IntroductionWhen we try to assess the viability or competitiveness of any industry the bottom line is still usually, ""Can we produce a pound of product cheaper than the competition?"" Canada's copper industry is certainly no exception. However, as with most resource-based industries dependent upon exports, there are many factors which have a significant effect on the cost components which make up the total cost of producing and selling a pound of copper. It is desirable therefore to have as clear a picture as possible of the cost components, the major factors affecting them, and how they compare with the competition, particularly the third-world copper producers.In this paper we have attempted to provide a brief outlook for world copper markets and a brief overview of Canada's competitive position. We have also attempted to document those factors which will have the greatest impact on future production costs, and have suggested possible initiatives to utilize inherent Canadian advantages to enhance our competitive position. Special emphasis has been placed on technological initiatives designed to make full use of these ""advantages"", to develop superior beneficiation and extraction! refining technologies. Major factors considered in the present study are:"

Jan 1, 1986

By D. J. Dodds, W. L. Schroeder

INTRODUCTION The plate loading test is a simple, useful tool in rock mechanics. The test consists of applying load to a rock surface and noting the resulting deflections. Plate loading tests are typically used to obtain modulus of deformation and related material properties, but can also provide information on blast damage and in situ stresses (1). Properties obtained are of course dependent on test procedure and test environment . In order to eliminate extraneous results it is essential that the interrelationship between the physical test environment and various rock properties obtained be thoroughly understood. Test interpretation is based upon elasticity methods, and the general assumptions made during analysis which include the following: 1. The rock is homogeneous, isotropic, elastic and continuous. 2. The stress is induced in a semi-infinite solid. 3. The plate is perfectly rigid or completely flexible. 4. Rock properties are independent of in situ stresses. 5. The plate and rock surface are smooth and parallel.

Jan 1, 1974

The presence of undetonated explosives in a rock face after firing constitutes a hazard which can result in a fatal or serious accident if undetected before drilling commences.Most accidents caused by drilling into explosives are the result of failure to examine the working face properly and lack of care in subsequent drilling operations; it is not always realized that explosive may be left in the butts of holes or may be driven into cracks or crevices in the rock.Obviously the best means of preventing accidents of this nature is to adopt methods of drilling, charging and firing which will reduce the hazard to a minimum.There are three ways in which undetonated explosives may be left in the rock face, namely:1. Misfires.2. Cut-off shots.3. Incomplete detonation or failure of the charge to propagate throughout.MisfiresNo attempt will be made in this paper to deal fully with the question of the prevention of misfires, as apart from the fact that most of the preventive methods are well known, it is believed that if the miner receives his explosives and means of initiation in good order, and proper care is taken in their use, the failure of a charge to fire will be a rare occurrence. The provision of central fuse capping stations on mines has gone a long way towards the elimination of misfires caused by the mishandling of safety fuse anddetonators.

Jan 1, 1956

A study of the electrolysis of PbS in molten PbCl2 showed cathode efficiencies which increased with current density at fixed sulphide concentrations, and decreased with increasing sulphide concentration at fixed current densities. The anodically produced sulphur dissolved rapidly in the melt, the rate increasing with temperature and sulphide concentration. Experiments with diaphragm cells, made to determine the relative effects that dissolution of lead and sulphur have on the cathodic current efficiency, demonstrated that dissolution of sulphur was the major contributor to the lowering in efficiency.

Jan 1, 1973

By David Cheung, S. Paul Singh

"The characteristics of a blasted muck pile can have a significant effect on the productivity and economyof loading and hauling operations. Poorly fragmented and tight muck piles, caused by insufficientdisplacement of the broken rock, lead to higher digging and hauling costs. Therefore muck pile must be tailored to suit the loading and hauling equipment. In order to achieve this objective, it is imperative to understand the relevant muck pile characteristics and factors governing them. In general, muck pile characteristics are governed by the blast design parameters, rock mass geology, explosive characteristics and post-blasting requirements."

Jan 1, 2017

By H. Yavuz

Physical modelling is one of the research tools in the understanding of the failure mechanisms and the deformations likely to be experienced by the strata during mining operations. Success of the physical models to predict the strata behaviour depends on satisfaction of the scaling requirements in modelling material used. This paper gives results from a laboratory work carried out into the factors influencing the strength and elastic properties of a physical model material to satisfy the scaling requirements determined from application of dimensional analysis to the pertinent variables affecting the deformation and failure of the underground structures. It was found that the conditions for preparing the material over its composition had a great influence on the final properties. The effect of different water quantities, sand size and mixing time upon the properties of modelling material was studied and water requirement for different proportions of sand/plaster to prepare the material was optimized. Various sand/plaster ratios of compositions were cured at three different levels of oven temperatures. Curing at low temperature produced material within the average modulus ratios ranging from 290 to 432, which are common to most rock types according to Deere?s rock classification, whilst curing at high temperature produced material within the low modulus ratios ranging from 64 to 140 depending on its composition. A combination of low and high temperature curing resulted with an increase in modulus ratio compared to high temperature curing. Curing the material at low temperature compared to other curing temperatures provided a satisfactory range of strength ratio. It has been shown that the relative amount of filler to plaster in the mix controls the frictional properties of the material and results with an increase in strength and modulus ratio of the material provided that suggested preparation and curing conditions were applied. Model material developed by curing at low temperature simulated modulus ranging from 241 to 343 and strength ratios ranging from 11.6 to14.8 of a coal mine rocks, satisfactorily.

Jan 1, 2003

By S. Boone, J. N. Shirlaw

INTRODUCTION Soft, near normally consolidated clays generally provide ideal conditions for tunneling using Earth Pressure Balance (EPB) shields. It is easy to turn the clay into a low permeability, viscous spoil that can be pressurized to maintain the required face pres-sure. Despite this, there are records of relatively large, and often quite variable, surface settlements over EPB driven tunnels in soft clay. To understand this variation it is necessary to identify the various factors that contribute to settlement. Tunnels in soft clay are ideal for study these effects in the field, as an unsupported void will close almost immediately, due to the low shear strength of the soil. In the short term, deformation in a soft clay will occur at constant volume, so short term surface settlements can be related to movements at tunnel level. In this paper, data will be used from EPB driven tunnels in Singapore marine clay. In all of the cases discussed the lining consisted of precast concreted segmental rings erected in the tail of the shield. The marine clay in Singapore has been studied, among others, by Tanaka et al.(2001). The clay typically has a plasticity index of 40 to 60, and the undrained shear strength (SU ) can be derived from: SU = 0.22 svo' where svo' is the current vertical effective stress. Figure 1 shows a summary of undrained strength/depth plots used for design on two sections of Singapore’s North East Line. The stability of a tunnel in clay can be assessed by comparing the stability number (N) of the tunnel with the stability number at total collapse (NTC). The stability number can be calculated from the equation: N = (?Z + q – Pt)/SU where: ? = the average unit weight of the ground above the springline of the tunnel Z = the depth to the springline of the tunnel from the ground surface q = the surcharge Pt = the support pressure within the tunnel The stability number at total collapse depends on the size, geometry and depth of the tunnel, and typically ranges between 5 and 9. Charts for assessing the number at total collapse are provided in Kimura and Mair (1981), based on the testing of model tunnels in a geotechnical centrifuge. For tunnels in the Singapore marine clay, the stability number of an unsupported tunnel would be over nine if the tunnel ois more than 8m deep. As a result, a support pressure

Jan 1, 2007

By A. Melkumyan, M. Balamurali, J. Zigman

Understanding the contribution of geophysical variables is vital for identifying ore indicator regions. Both magnetometry and gamma-rays are used to identify the geophysical signatures of the rocks. Density is another key variable for tonnage estimation in mining, and needs to be re-estimated in areas of change when a boundary update has been conducted. Modelling these geophysical variables in 3D will enable investigation of the properties of the rocks and improve our understanding of the ore. The Gaussian Process (GP) was previously used to generate 3D spatial models for grade estimation using geochemical assays. This study investigates the influence of the following two factors on the GP-based autonomously generated 3D geophysical models: the resolution of the input data, and the number of nearest samples used in the training process. A case study conducted on a typical Hammersley Ranges iron ore deposit using geophysical logs, including density, collected from the exploration holes, is examined in this paper.

Sep 1, 2021

By W. Banda

Paper written on project work carried out in partial fulfilment of Phd. (Process Engineering) degree* The recovery of cobalt and copper from waste slag was studied in a plasma DC-arc furnace in reducing conditions. Three fluxes, CaO,CaF2, and TiO2, were investigated for their influence on selective recovery of cobalt into an iron-rich alloy. A further investigation on the influence of furnace power on the reduction of slag to recover cobalt to the alloy showed that a change in power setting had an unexpected effect on the recovery of metals to the alloy, in that selectivity of base metal recovery over iron recovery decreased at an increased power level. Keywords: DC-furnace, reduction, nonferrous, slags

Jan 1, 2004

By C. R. Copeland

Water sprays are a common method used to reduce particulate matter (PM) emissions. Various factors such as wettability, surface area coverage, fine particle engulfment rates, interparticle adhesion forces, suppressant penetration and suppressant longevity have all been suggested as critical factors in achieving effective PM control. However, it has not been established which of these factors are the most important. Experimental work indicated that suppressant penetration is the most critical of these factors. The length of time after application that suppressants were effective was also improved by using hygroscopic reagents that retained moisture to prevent evaporation. Maximizing suppressant penetration and improving suppressant longevity led to an average 86% reduction in PM10 concentrations in laboratory dust tower tests.

Jan 1, 2008

By Gregory Molinda

Groundfalls are much more likely to occur in coal mine intersections than in entries. NIOSH is using the experience of U.S. coal mines to determine the factors which influence intersection instability and provide guidelines for the safe excavation and support of intersections. Detailed field investigations have resulted in a database of U.S. coal mines containing 12 mines and 639 roof falls so far. By using the roof fall rate as the outcome variable, correlations between roof geology (CMRR), intersection span, and roof support have been established. Case studies have indicated that replacing 3 way intersections with 4-way intersections may not reduce the total number of roof falls. Additionally, the size of intersection spans tend to decrease with lower (weaker) CMRR. Protocols have been established for the collections of roof bolt parameters. The performance of individual roof bolts can now be tracked with roof fall rate.

Jan 1, 1998

By R. Laird Auchmuty

A NUMBER of factors, of varying importance, should be considered in assessing mineral land-here specifically coal land -for tax purposes. (1) Is the coal developed or un- developed'! (2) If undeveloped, is it surrounded by active development in adjoining properties? (3) Accessibility of railroad facilities to the property. Sometimes the railroad itself is of importance. (4) Cost of development of the seam under consideration, whether it can be developed by a drift from the outcrop or whether it will require deep and costly shafts or slopes. (5) Is it definitely known that the coal seam being assessed is of minable thickness and quality on the property? (6) Thickness of recoverable coal from the seam. (7) Quality of the coal. (8) Is the seam being assessed likely to be more costly to mine than other seams in the same district? (9) Is there an active market demand for coal from the seam being assessed? (10) Is the coal held only as protection to surface structures and in such location that it can never be mined? (11) Is the coal in a solid piece or is it in pillars that have been standing for some years as a result of incomplete mining in an old operation? (12) Expected percentage of recovery from the seam being assessed as determined by present mining practice in similar properties. (13) Value of the seam as indicated by sales of similar mineral rights in the immediate district. (14) Current royalty rates of leases for coal in the seam under consideration.

Jan 1, 1939

By F. Shi , D. Lay, C. Antonio

High Voltage Pulse (HVP) technology has the potential to transform traditional mineral processing practice in the mining industry. HVP pre-treatment has been shown to enable ore preconcentration, achieve ore pre-weakening and improve mineral liberation. In order to improve the efficiencies of these novel HVP applications, it is essential to understand how HVP operational factors affect ore breakage in HVP pre-treatment. A two-level fractional factorial experiment using two rock samples, a gold-copper ore and a basalt sample, was performed to determine which factors have statistically significant influences on breakage probability, size reduction, and energy efficiency, and which factors have insignificant influences. Operational factors investigated include applied voltage, electrode gap, number of pulse discharges, the number of rocks being processed per batch, and rock size. In total, 1920 batch tests were conducted. For ore breakage characterised in terms of breakage probability and the degree of size reduction during HVP pre-treatment, the dominant factors were identified to be the number of pulse discharges, voltage, and the number of particles present in the processing zone. As all these three factors are related to the specific energy, it is concluded that the specific energy is the most important factor controlling ore breakage in HVP treatment. In terms of the efficiency by which spark energy is transferred from the generator energy, the factors found to have the most dominating influence were the particle size, the number of rock particles present in the processing zone and the voltage. Increasing the values of these factors reduced the loss of HVP energy during the energy transfer process. The factorial experiment using the two ore samples with vastly different mineralisation produced similar results. This proves that the dominant factors affecting HVP breakage are generally applicable to different ores types. Keywords: High voltage pulse, ore breakage, factorial experiment, specific energy

Jan 1, 2020

By Andy Fortin, André Vien, Christophe Bouché, Jeff McKay

"The technology and equipment design of the Twenty-first Century permit us to exploit low-grade ore bodies with milled tonnages reaching 300,000 tpd. Because of their substantial operational costs (energy, wear parts, etc) and precarious economic situations, the operations of today must maximize their metallurgical performance.The implementation of an Expert System becomes a logical avenue to pursue in view of increasing plant performance.Many operations, following the implementation of an Expert System, meet the objectives they determined before its integration; such as increased tonnage, stability, decreased costs, etc. However, they often cannot develop the full potential of the system due to certain factors that have been neglected or omitted during the implementation of the system.Three main elements have been identified during the implementation phase at INMET Mining Troilus Concentrator: 1- Instrumentation & Control 2- Software 3- Integration. Even though they have been clearly identified, these elements are often neglected due to lack of resources or lack of comprehension on the part of the operations personnel. This document will demonstrate, based upon our experience at Troilus and that of Metso Minerals, that we can identify and handle many factors which influence the profitability of the Expert System, for both short and long-term process control improvements.INTRODUCTIONThe Inmet Troilus Mine is an open pit mine, situated 175 km north of Chibougamau in the province of Québec, Canada. The mill, which started production in November of 1996, was originally designed to treat a gold – copper ore at a rate of 10,000 tpd.In early 1998, the mine plan called for a pit pushback and decreasing head grades for the following two years. With the price of gold nearing decade lows, the Troilus project was facing a major economical setback. There was a sense of urgency to reduce operating costs below the market price of gold. The mill team presented a project to management calling for an increase in mill throughput while minimizing capital expenditures and operating costs. This idea was supported by the existing mine plan, which called for a mine cut-off of 0.7 g/t Au and stockpiling low grade 0.5 g/t material for future milling."

Jan 1, 2003

By James J. Scott

I welcome this opportunity to speak before the Coal Division of the AIME in such an attractive setting as the Pacific Northwest. With the development of the Centralia project, the Pacific Northwest will have its first major coal-fired thermal electric generating plant. This State has a long history of coal mining that diminished with the passage of coal-fired steamships and locomotives but is now reviving with the growth of electrical power demand. Because this 1,400 row plant is to be supplied with surface-mined coal, it is particularly appropriate that this area be the setting for a talk on factors influencing the growth of surface coal mining in the West. During the course of my talk, I will touch on a number of factors including electric power demand, coal resources, production trends, environmental considerations and trends in State and Federal activities that I feel will influence surface coal mining in the West. Total electric power consumption by the year 2000 is expected to reach 9.4 trillion kilowatt-hours. Predictions of total coal consumption for electric power generation by that year range from a low of 845 million tons to a high of 1,520 million tons, or 2.6 to 4.7 times the amount used for this purpose in 1970.

Jan 1, 1971

By Aline Tatom

This paper presents numerical and experimen¬tal results dealing with the application of ferric ion oxidation of uranium in acidic media. Conclusions are derived from matching numerical results to experimental data taken on one-dimensional laboratory leaches using ore from a South Texas Coastal plain deposit. Since the numerical results can be made quite general, we are able to extract and quantify the effects of oxidant concentration, flow velocity, mass transfer, chemical kinetics, and competitive oxidant consumers (pyrite and molybdenite) on the experimental results. Our results suggest that the leaching of uranium is a mass transfer controlled while that of pyrite is kinetically controlled.

Jan 1, 1981

By A. G. Matyas

Process improvements which have reduced the lead content of slag from the Brunswick lead blast furnace are described. Microscope examination and electron microprobe analyses, supported by the results of slag settling and viscosity tests, showed that typically about 70% of the lead in the lead blast-furnace slag was present in the form of entrained prills of metallic lead. The total lead content was found to increase with the magnetic susceptibility of the slag. Measurements in the furnace settler indicated the presence of a magnetite-rich layer between bullion and slag, arising from high magnetite levels in the slag. This layer was believed to inhibit the settling of entrained lead from the slag. Tracer tests showed that the average slag residence time in the settler was less than 2 minutes. Improvements in coke quality and sizing, which led to a reduction in the slag magnetite content, and the installation of a larger settler and a continuous Roy tapper, have all contributed to a significant decrease in the slag lead content.

Jan 1, 1977