Search Documents

By Jr. Watts, B. K. Cantrell, K. L. Bickel, J. F. McDonald

"A field trial was conducted at an underground gold mine to evaluate diesel fuel derived from soybean oil (soy-methyl-esters or “biodiesel”) as an alternative to commercial, low-sulphur, number 2 diesel fuel (D2). A 2.7 m3, 18-ton load-haul-dump (LHD) unit, powered by a naturally aspirated, indirect injection (pre-chamber), 100 kW diesel engine was used as the test vehicle. The LHD was equipped with a diesel oxidation catalyst. The LHD operated satisfactorily on the biodiesel fuel. Operators observed a slight decrease in power and an absence of black smoke.Diesel particulate matter (DPM) concentrations were monitored for a six-week period while the LHD was operated with either the biodiesel fuel or the D2 fuel. DPM concentrations were measured in the mining section’s clean air intake, exhaust and on the LHD. Reduction in DPM emissions was determined from the measured difference in DPM concentrations between the clean air intake and the exhaust. The biodiesel fuel reduced energyspecific DPM emissions approximately 75%, from 3.6 ± 1.8 g/kW-hr to 0.86 ± 0.27 g/kWhr. Time-weighted average DPM exposure, measured near the LHD operator, was reduced from 0.67 ± 0.13 mg/sm3 to 0.28 ± 0.12 mg/sm3, or approximately 58%, when the biodiesel fuel was used. IntroductionDiesel exhaust consists of noxious gases and diesel particulate matter (DPM). Recent attention has focussed on the potential carcinogenicity of DPM and the potential health impact on miners. The National Institute for Occupational Safety and Health (NIOSH) recommended that whole diesel exhaust be regarded as a “potential occupational carcinogen”, and that reductions in workplace exposure would reduce cancer risks (NIOSH, 1988). The International Agency for Research on Cancer (IARC) declared that “diesel engine exhaust is probably carcinogenic to humans” (IARC, 1989)."

Jan 1, 1997

By Mikula PA

This paper presents the results of in-situ and laboratory investigations into a mining method which utilises conventional continuous mining techniques to carry out two passes in thick coal seams, resulting in the development of stable pillars with relatively small width dimensions and heights up to 6 m. Geotechnical investigations included structural mapping, brightness logging and standard laboratory testing. Virgin stress was measured using overcoring techniques. Two approaches to pillar design were used in the study. These were; pillar design based on empirical formulae and laboratory testing, and pillar disign using calibrated mathematical models. A trial panel was developed at 300 m depth to study pillar deformation and stress changes due to mining. The extent of rib deformation was studied using borescopes and extensometers. In-situ geotechnical measurements were used to calibrate displacement discontinuity and finite element mathematical models of the coal seam. These models were then used to predict the behaviour of a small panel of pillars which were to be developed to 6 m height. The mining method was shown to be feasible provided adequate rib support was installed. The benefit of rib support was found to be two-fold, in that it increased confinement of the pillar in zones of low horizontal stress, while reducing horizontal stress relaxation in zones of high horizontal virgin stress. The possiblity of roof control by designing the small pillars to yield on retreat is discussed.

Jan 1, 1986

By A. C. du Preez

Mintek has been involved in extensive test work since the early 1990s on the recovery of nickel and cobalt from leach liquors saturated in calcium, using synergistic solvent extraction systems. During this period the Nicksyn? reagent was developed, optimized, commercially manufactured, and tested by Tati Nickel on a demonstration plant for more than 2800 operating hours. Efficient recovery of nickel without the co-extraction of calcium, thus avoiding gypsum formation in the extraction and stripping circuits, was illustrated. This synergistic system was recently evaluated on a laboratory scale for the recovery of nickel and cobalt from synthetic lateritic sulphate leach liquor containing about 3 g/L nickel, 0.5 g/L cobalt, 0.7 g/L manganese, 20 g/L magnesium, and with calcium at saturation. Extraction and stripping parameters were determined for this feed liquor and are discussed in this paper.

Jan 1, 2014

By D. Nutakor

The ability of computers to create synthetic representations of the real world in virtual reality offers a number of opportunities to enhance training methods used in the mining industry. Unfortunately, the training effectiveness of virtual reality systems currently used in the mining industry has received only limited testing. Miner Simulation (MinerSIM), an augmented reality system with integrated hypermedia suitable for training underground miners in the basics of using a jackleg drill to install rock bolts in a virtual mine environment is in its evaluation process at the University of Missouri-Rolla Experimental Mine. This paper discusses evaluation methodologies of the MinerSIM system, which consists of experimental and control groups with control students learning via traditional lecture and text formats. Preliminary results from usability tests of the first part of MinerSim, which is an online tutorial on underground rock bolting, are presented.

Jan 1, 2008

By R F. Sandenbergh

Due to environmental considerations, mineral processing plants are increasingly recycling water to decrease the impacts of wastewater on environment and the depletion of fresh water resources. Industrial experience has shown that increasing recycling water in flotation typically negatively impacts the recovery and selectivity, especially in the selective flotation of minerals from complex sulfide ores. The major reason for the reduced selectivity is typically the inadvertent activation of sphalerite or pyrite by the heavy metal ions (HMI) in solution. These HMI are often produced during milling and flotation and absorbed by other minerals. In the normal flotation pH value range (8 - 10), these HMI are often in the form of precipitates or complex ions that may re-appear in solution or become active should conditions favour this. In this paper, microflotation, batch flotation and XPS surface measurement were used to investigate the use of HMI absorbents additions to the pulp to improve flotation selectivity of a complex sulfide ore. It has been demonstrated that HMI removal does improve flotation selectivity by facilitating more effective depression of the sphalerite. Microflotation and XPS surface measurements have shown that HMI absorbents compete with sphalerite to absorb HMI, and thus reduce the surface concentration of HMI on those sulfides. The practical use of HMI absorbents in complex sulfide ore flotation is also discussed.

Jan 1, 2005

By Chu E. Ho

Key variables that govern the jet cutting process are examined based on fundamental theories of jet hydrodynamics and soil mechanics. Under normal conditions of jet grouting operations, lift speed and rotation speed are found to be of less importance than the depth of jetting, nozzle pressure, nozzle diameter, and the soil bearing resistance, with regards to their influence on jet cutting distance. An analytical equation linking the governing variables is proposed, which allows for the possibility of evaluating column diameters achievable in different ground conditions based on theoretical calculations. When used in conjunction with shallow jet grouting field trials, the equation can provide a means for extrapolating trial results to conditions at actual depths for production jet grouting.

Jan 1, 2006

By Lawrence Mirabelli, AngloGold Ashanti, Greg Gibson

Cripple Creek & Victor Gold Mining Company (CC&V) operates the largest surface gold mine operation in Colorado and is located west of Colorado Springs in Teller County between the towns of Cripple Creek and Victor. Gold was first discovered in the Cripple Creek mining district in the 1890s. CC&V has been conducting gold mining and precious metal extraction operations in the Cripple Creek Mining District since 1976. Current reserves are only amiable to surface mining since previous underground mining has depleted near surface ore rich veins.

Jan 1, 2014

By Matthew S. Sanchez, Richard J. Lee, Matthew D. Zock, Drew R. Van Orden, Yumi Kamiya, Edward B. Ilgren

In many developing countries, asbestos is still used for friction products, insulation, and asbestoscement products. However, there is very limited modern data evaluating the airborne concentrations of asbestos fibers in operating asbestos plants. We have conducted an Industrial Hygiene survey, using state of the art PCM and TEM analysis, of a Bolivian asbestos cement plant that uses crocidolite during the production of roofing shingles and water tanks. The study is the first to use modern analytical measurements in an uncontrolled asbestos environment. Thus, this study offers insight into the historical airborne exposures at asbestos plants operating before modern dust control measures were introduced or airborne fiber levels regulated. The results suggest that fiber concentrations are far in excess of those for which current models would predict the onset of asbestos disease and mesothelioma. Significantly, the plant and community do not have an elevated incidence of asbestos disease or mesothelioma. Airborne fiber levels during comminution and fiber sizing ranged from 100 to as much as 1,000 f/cc. Fiber levels in the mixing, forming and finishing areas ranged from 0.5 to 9 f/cc. Based on the number of overloaded samples and estimates of their concentration, historical estimates of exposure may be underestimated by an order of magnitude. Also, an excellent correlation (1:1) between the PCM and TEM fiber concentrations (for fibers _0.25 um diameter) were obtained, raising questions about the conventional wisdom that the PCM systematically undercounts fibers. The results of this study further indicate that current models may overestimate the risk of asbestos disease and mesothelioma.

Jan 1, 2012

By L. Naude, J. Cloete, S. Engelbrecht

The results of an investigation evaluating whether an industrial plant, currently operating using sodium isobutyl xanthate (SIBX) as primary collector for sulphide minerals (mainly chalocopyrite), could adapt to operate using an alternate primary thiol collector without compromising plant and metallurgical performance. Initial laboratory scale flotation tests identified commercial dithiophosphate (DTP)-based and thionocarbamate (TC)-based collectors, that when blended, showed potential to replace the incumbent SIBX primary PGM collector. Industrial plant trail results show that there was no deterioration in recovery of 4E PGMs, even at a lower concentrate grade when operating the plant on the identified (DTP + TC)-based collector blend compared to SIBX. The effect on Cr2O3 content in the final concentrate was also found to be negligible. The (DTP + DTC)-based collector blend also showed promise in terms of plant adaptability in accommodating a new primary specialty collector blend. These observations highlighted the potential of replacing xanthate primary collectors with alternate thiol collector blends for PGM flotation. Keywords: PGM, xanthate replacement, specialty collector, sodium iso-butyl xanthate (SIBX), dithiophosphates (DTP), dithiocarbamates (DTC)

Jan 1, 2020

By J. A. Herbst

Fine coal cleaning by froth flotation has become common practice in the U.S. with more than 80,000 tons treated in this way per day. In spite of this large tonnage, developments in the automatic control of coal flotation circuits have lagged significantly behind those for mineral systems. One reason such developments have been limited is that instruments have not been available for the on-line measurement of carbon or ash and another critical variables in coal slurries. A second reason is that the influence of the operating variables on coal flotation has not been completely understood. During the last few years some of the required instrumentation has been developed and an improved knowledge of the flotation process itself has occurred through mathematical modeling; as a result certain control strategies for coal flotation are beginning to emerge. This paper attempts to evaluate several control strategies using a detailed flotation dynamic simulator, DYNAFLOAT. After constructing a process matrix for the system of interest, promising alternatives for linking manipulated and controlled variables have been analyzed. In order to develop combined grade and recovery control strategies, the authors found it necessary to construct a grade/recovery map with the aid of the simulator to drive the system to known final, feasible grade/recovery operating conditions. Finally, an advanced strategy which uses an on-line model to identify disturbances and take control actions is proposed.

Jan 1, 1983

By Stephen Phillips, Luigi P. Gonano

Vertical circular shafts have been proposed for multiple access to high level nuclear waste deep geologic repositories. Shaft construction is a critical path item in the commissioning of a repository. Other constraints on the shaft design and construction criteria include the lack of design precedence for long term performance and the importance of minimizing rock and groundwater disturbance. A comparative evaluation of conventional and mechanized shaft sinking techniques is presented in the context of the particular geologic and design constraints. Technical and non-technical factors for blind drilling, blind boring, raise-reaming, drill-and-blast and ream-and slash methods are reviewed for typically "hard rock" and "salt" type repository sites. Appropriate shaft designs are developed, the suitability of each method to the particular requirements evaluated and construction costs and schedules determined. The explicit appraisal of the significant design factors for each method serves as a rational basis for the preliminary selection of the most suitable sinking technique for a particular set of site/design conditions.

Jan 1, 1983

By Philip Morey

Large scale surface coal mining will be required to fill future energy demand in the United States. In realization of this long-term commitment to coal resources, the U.S. Energy Re-search and Development Administration sponsored a study to determine the costs and problems of large-scale surface coal mining. As a result of this study a series of computer models were developed that can be used by government and industry to: 1) facilitate mine design and equipment selection, 2) provide detailed analyses of mining and processing costs. Two types of models were developed: detailed simulation models, which provide detailed information on mining systems and equipment to assist in mine design and equipment selection1 and broad models, which provide a first-order evaluation of deposits and new ventures for an entire mining complex. The complete model series permits examination of surface coal mining under a variety of terrain conditions. Six different mining methods were analyzed and documented during the overall project: 1) Area stripping with draglines, 2) Area stripping with draglines, extended bench, 3) Contour stripping with draglines, 4) Area stripping with shovels (loaders) and trucks, 5) Mountain top removal with shovels (loaders) and trucks, 6) Multiple dipping seam mining with shovels (loaders) and trucks. Each major operation in the coal mining pro-cess is represented in these models so that the best methods and equipment may be selected and 50 that the impact of such selection will be reflected in estimates of capital investment, operating costs, and coal price. Individual models allow the user to separately analyze overburden removal, overburden drilling and blasting, coal drilling and blasting, coal loading and hauling, coal preparation and handling, land reclamation, and premining, facilities, and administrative expenses. Because it is impossible to cover all the models in this paper, only the detailed simulation models representative of the technique "area stripping with draglines," are described. The Fort Union Strippable Coal Resource Region, one of eight test cases, is used as an example to describe the models.

Jan 1, 1978

By M. K. Mohanty

One of the main objectives of this study was to evaluate a fine-coal cleaning circuit using an enhanced gravity separator specifically for a high sulfur coal application. The evaluation not only included testing of individual unit operations used for fine-coal classification, cleaning and dewatering, but also included testing of the complete circuit simultaneously. At a scale of nearly 2 t/h, two alternative circuits were evaluated to clean a minus 0.6-mm coal stream utilizing a 150-mm-diameter classifying cyclone, a linear screen having a projected surface area of 0.5 m2, an enhanced gravity separator having a bowl diameter of 250 mm and a screen-bowl centrifuge having a bowl diameter of 500 mm. The cleaning and dewatering components of both circuits were the same; however, one circuit used a classifying cyclone whereas the other used a linear screen as the classification device. An industrial size coal spiral was used to clean the 2- x 0.6-mm coal size fraction for each circuit to estimate the performance of a complete fine-coal circuit cleaning a minus 2-mm particle size coal stream. The ?linear screen + enhanced gravity separator + screen-bowl circuit? provided superior sulfur and ash-cleaning performance to the alternative circuit that used a classifying cyclone in place of the linear screen. Based on these test data, it was estimated that the use of the recommended circuit to treat 50 t/h of minus 2-mm size coal having feed ash and sulfur contents of 33.9% and 3.28%, respectively, may produce nearly 28.3 t/h of clean coal with product ash and sulfur contents of 9.15% and 1.61%, respectively.

Jan 1, 2008

By John Skelton, E. J. Harvey

Seepage runs (stream flow measurements in a short time at many points in a basin,) and stream flow records are used to locate losing areas in stream basins in the Missouri Ozarks. The terrane consists of dolomitic limestone and sandstone of Ordovician and Cambrian age. Side-looking radar imagery emphasizes variations in topography and reveals two types of drainage basin topography, rough and smooth (deeply dissected and slightly dissected basins). In the deeply dissected basins (rough ones), main streams and tributaries generally gain. In the slightly dissected basins (smooth ones), the streams lose a part or all of their flow. Logan Creek, a tributary of Black River in the southeastern Ozarks, loses much of its storm runoff and all of its dry weather flow. East and West Forks of the Black River, north of Logan Creek, gain water through most of their main stems. On radar imagery Logan Creek basin has a light uniform tone and smooth texture in contrast to the darker tone and rough texture of the East and West Forks. The contrast is due to the difference in degree of dissection. Therefore, radar imagery may be useful in suggesting gaining or losing streams (or reaches of streams).

Jan 1, 1973

By G. Chisakuta, P. Bwando, G. Mitshabu

By the end of 2022, the south-eastern Copper Belt region of the Democratic Republic of Congo was host to more than 40 small, medium, and relatively large sized copper solvent extraction sites. To date, solvent extraction reagents supplied in this region have never exceeded 50% of ketoxime content. We generated laboratory extraction and strip isotherms and used these with the BASF IsocalcTM modelling software to assess the benefit of using higher ketoxime blends on the main metallurgical performance indicators such as copper recovery and net transfer. Pure ketoxime extractants combine a relatively low strip point and a decent loading capacity, which are most effective as the pH of the pregnant leach solution gets closer to 2.

Jan 1, 2023

By M. Holuszko, I. Mikhalev

"Previous studies described by Galvin et al. (2017) have shown that for Australian bituminous coal fines, both in batch and in continuous process, the new improved oil agglomeration procedure based on the use of high-internal-phase (HIP) emulsions, as compared to the conventional “pure oil” agglomeration process, enables a significant reduction in the amount of oil while reaching a high yield of clean coal (approximately 90% of agglomerates greater than 355 µm in size) in a significantly shorter time. The HIP emulsion used in these experiments comprised up to 95% vol. aqueous solution of sodium chloride (3% wt. concentration) and for the rest, a mixture of kerosene (oil) and sorbitan monooleate (SMO emulsifier) in a 1:1 ratio as a binder. This study evaluates the applicability of the new HIP-oil agglomeration process to treat Canadian bituminous ultra-fine coal and Russian sub-bituminous coal fines and compares results from agglomeration to the flotation response of both coals. Oil agglomeration is known to be sensitive to surface properties of coal. Since surface properties of coals depend not only on the rank of coal but also on their origin (depositional environment) and mineralogical composition, both the applicability of this new improved agglomeration process to the non-Australian coals and its efficiency became the motivation for this study. To evaluate the applicability of the new process to both Canadian bituminous and Russian sub-bituminous coals, a series of bench-scale tests were carried out under conditions similar to those described by van Netten et al. (2016) for the Australian coals. Based on the results obtained in this research, new boundary conditions for the application of the HIP emulsion-based oil agglomeration process have been outlined and conclusions on the viability of the new process to treat ultra-fine coal from Western Canada and Russian sub-bituminous coal fines have been reached.INTRODUCTION In most cases, to meet the market requirements, the mined coal has to be processed to reduce the ash content by the removal of mineral matter and thus to increase the quality of the coal products (van Netten et al., 2016). Generally, flotation is used for processing fines from high rank coals; however, there are high losses of very fine coal due to the inefficiency of this process. Furthermore, difficulty in dewatering the fine coal results in excessive moisture levels causing coal handleability issues, which increases costs in the coal-cleaning industry (Capes & Darcovich, 1984). Much of the development that has occurred in fine coal cleaning has taken place with higher-value coal, often metallurgical (Klima et al., 2012). If the fine coal is deemed to be too difficult or expensive to process, it may be discarded as waste (van Netten et al, 2014). Such disposal not only creates an environmental liability but may also result in the loss of a valuable, high quality product that is better liberated than the coarser fractions of coal."

Jan 1, 2018

By V. Sheikhzadeh, M. Saghaeian, N. Esmaeili, R. Hejazi, A. D. Ahmadabadi

The main challenges in most low grade iron ore deposits are finding the optimum flowsheet for beneficiation to achieve a final concentrate from both technical and economic viewpoints. Dry preconcentration techniques are being used to assist in reducing the amount of ROM feed to the plant. In this paper the benefits of utilising a dry cobbing magnetic separation technique for upgrading the product of HPGR in a closed circuit with dry screen 4 and 1.4 mm by performing a pilot scale test work was investigated. The experimental test work was done on two sample types of Yogi BIF magnetite iron ore located in Western Australia. Prior to magnetic separation studies, detailed characterisation of the feed materials including physical, chemical, mineralogical and magnetic properties were carried out. Furthermore, the effects of process parameters: drum rotation speed (1.5, 2.5 and 3.5 m/s), magnetic field intensity (1100 and 3800 gauss) and feed size (minus 4 and 1.4 mm) were investigated. The results revealed that sample type1 with 33.90% Fe could be upgraded to 41.51% Fe by using a stage of 1100 gauss dry magnetic separator with 69.12% weight recovery and 84.36% Fe recovery at a size of 4 mm. Also for sample type2, it is possible to increase Fe grade from 29.84% to above 36.68% with 75.58% weight recovery and 90.32% Fe recovery by applying one stage of 1100 gauss dry magnetic separator to a 4 mm size sample. Keywords: Banded iron formation (BIF), pre-concentration, dry cobbing technique, magnetic separator

Jan 1, 2020

By H. K. Conn

This paper discusses briefly the evaluation of chrysotile asbestos deposits in ultramafic rocks. Such deposits are limited to serpentinized peridotite and/or dunites. The purpose of any evaluation is to determine whether a deposit contains sufficient ore mineral to justify profitable exploitation. Dimensions of a mineral zone are established by conventional methods, such as mapping, ground magnetic surveys, diamond drilling or underground exploration. The value of the contained asbestos fibre Is dependent on numerous physical properties such as fibre length, strength, flexibility, as well as the actual amount of fibre present. The determination of grade is difficult. The Quebec Standard Test (Q.S.T.) is used to grade fibre according to the proportionate lengths of fibre present. A method of visual vein counting allows calculation of an approximate percent fibre together with a simulated Q.S.T. Various drilling methods are discussed, diamond drilling is favored. Bulk sampling is required to determine fibre quality. Correlation of visual techniques and laboratory methods are often difficult. Reasons for any variance are discussed. Underground bulk sampling of most potential ore zones is strongly recommended to confirm the viability of the property. Evaluation of slip fibre deposits requires greater reliance on laboratory testing as visual methods are difficult to apply. Cross fibre has greater inherent strength.

Jan 1, 1971

By Neha Shukla, Nikhil Dhawan

The current study examines the extraction of rare-earth elements from trichromatic phosphor of discarded tube lights via baking processes. The Y2O3: Eu3+ (YOX) and BaMgAl10O17: Eu2+ (BAM) phases completely decomposed during acid and alkali baking with > 90% Eu and Y extraction. Prior, selective acid leaching of the YOX phase enhanced the acid baking process at a lower temperature (< 230 ℃). Feed acid baking showed a maximum 87% Tb, 36% La, and 17% Ce extraction at 500 °C, 0.5 h, 1 ml/g H2SO4, and alkali baking yielded 16.1% Tb, 86% La, and 73% Ce at 300 ℃, 0.5 h, 50 wt.% NaOH. The acid baking of the acid-leached phosphor yielded 72% Tb, 95% La, 63% Ce, ~ 95% Y, and Eu extraction at 300 °C, 0.5 h, 1.05 mL/g H2SO4. Lower Tb extraction during the acid baking of acid-leached phosphor can be attributed to the formation of Ba3Tb( PO4)3 and BaTbO3 phases. Insoluble Si3Tb5 phase formation and partial decomposition of CeMgAl11O19: Tb3+ (CMAT) phase in the alkali baking route leads to lower Tb extraction. The acid baking process is suitable for extracting Tb, Eu, and Y, whereas the alkali baking process is suitable for La and Ce. The thermal analysis of phosphor and flux interaction depicts that alkali baking is less energy-intensive than acid baking. In comparison, the one-step acid baking process and the two-step alkali baking process yielded desirable extraction results (87% Tb, total RE (rare earth) 78.5% and 50.4% Tb, total RE 59.3%). The product yield in the acid and alkali baking route of feed, acid-leach phosphor is 36%, 29%, and 39%, 28.2%, respectively, with ~ 98% mixed rare-earth oxide purity.

May 5, 2022

By William G. Freeman

In comparison to many mineral commodities, barite has a low unit value. It is mined and sold in low volumes in high-grade (90-98% BaSO4) forms to basically one industry that uses approximately 75% of the free world production. Based upon the above criteria, all factors must be considered in determining if a barite deposit is economical; such as, the type of deposit, mining and milling methods required, transportation to the markets, tariffs, local political conditions, etc. In other words, barite mines are made--not found. The length of this paper precludes any indepth discussion of geology, mining and metallurgy of barite. Most of this information can be found in data already published, such as D. A. Brobst&apos;s bulletin1 on the Barite Resources of the United States.

Jan 1, 1971