Search Documents

By S. Sener

In this investigation, the changes in the grindability of both ulexite and colemanite related with the different structural modifications created by the heat treatment were examined with respect to work index (Wi). The effects of the heat treatment temperature and time on grindability index were also investigated. It was observed that, heat treatment significantly affected on the grindability of ulexite. The work index of original ulexite was found 7.11 kWh/shton and decreased to 3.5 kWh/shton level within 200-480°C for 60 minutes. On the other hand, the work index of original colemanite was found as 6.48 kWh/shton and no appreciable change was observed when heated up to 320°C. Thermally assisted comminution can be used to improve the grindability characteristics of ulexite. Besides, the different behaviour of ulexite and colemanite under heat treatment can be used for their separation. The artificial mixture of ulexite and colemanite could be separated with over 90% recovery by utilizing their different grindability characteristics by thermal treatment, semi-autogeneous grinding and screening.

Jan 1, 1999

By Xiaodong Ma, Marek Pawlik

Introduction Guar gum is a natural nonionic polysaccharide. Guaran, the functional polysaccharide in guar gum is a chain of (1?4)-linked ß-D-mannopyranose units with a-D-galactopyranose units connected to the mannose backbone through (1?6) glycosidic linkages. The poly-mannose chain is randomly substituted with galactose units at a mannose-to-galactose ratio of 1.8-1.0 [1]. Cheng et al. reported that the molecular weight of natural guar gum is 1.935 • 106 [2]. Robinson et al. found that the molecular weights of five grades of commercial guar gums ranged from 4.4 • 105 to 16.5 • 105 [3]. Guar gum is frequently used as a depressant of naturally hydrophobic gangue minerals (e.g. talc) in the flotation of PGM-bearing ores, and according to Harris et al. a wide variety of modified guar gums are available for this application [4]. The Canadian potash industry utilizes natural guar gum as a blinder of water-insoluble slimes in the flotation of potash (sylvinite) ores, a process that is carried out in a saturated KCl/NaCl brine. The role of the polysaccharide is to prevent a primary amine collector from adsorbing onto these unwanted fine minerals. Hydrophobic interactions between basal cleavage planes and the polymer appear to be involved in guar gum adsorption on talc [5,6]. Liu and Laskowski stressed the importance of metal impurities on mineral surfaces that can serve as the active sites for polysaccharide adsorption [7]. This postulate was consistent with the later observation that, in addition to hydrogen bonding, the adsorption of guar gum onto talc was strongly dependent on the surface concentration of magnesium sites [8,9]. In this case the adsorption process was visualized as metal-polysaccharide complexation facilitated by the cis-configuration of the hydroxyl groups of mannose monomers. Hydrogen bonding and chemical interactions with metal sites were also suggested by Rath and Subramanian in their studies on guar gum adsorption on biotite mica [10]. In a recent study, Wang et al. demonstrated that hydrogen bonding is the main driving force behind guar gum adsorption onto talc [11]. Their data also show that the adsorption density of guar gum on alumina is about five times lower than the adsorption density on talc. Pawlik and Laskowski reported that the amount of guar gum adsorbed on illite was independent of ionic strength over a wide range of salt concentrations [12]. The adsorption density of the polysaccharide on illite did not measurably change with ionic strength from that of distilled water to about 50%-saturated KCl/NaCl potash brine (~3N KCl/NaCl). However, guar gum adsorption on dolomite dramatically decreased over the same range of ionic strengths, and no reliable explanation of that phenomenon was proposed [12]. The water structure-breaking or structure-making capabilities of background ions are usually ignored when discussing adsorption mechanisms of polymers. The concept of “structure breakers” and “structure makers” was first introduced by Gurney, and Frank and Wen who postulated that each ion is surrounded by three distinct regions of water structure [13,14]. In the first layer, water molecules are tightly bound to the ion. The second region extends farther away from the ion and is referred to as the region of structure breaking. Only at larger distances, where the ionic field is weak, water molecules form the “normal” ice-like structure. It is also now recognized that the first layer can be further divided into the primary and secondary hydration shells. Small, strongly hydrated ions reinforce the “normal” structure of water and the region of structure breaking disappears. In contrast, large less-hydrated ions disturb the ice-like structure and generate an extensive region of structure breaking. Experimentally, these two effects can readily be distinguished through viscosity measurements. Increasing concentrations of structure-breaking ions result in a decrease of the viscosity of aqueous solutions. On the other hand, increasing amounts of structure-makers significantly reduce the viscosity of water. Alkali metal cations form a sequence known as the Hofmeister series. The Hofmeister series - Cs+, K+, Na+, Li+ - orders the cations from the least hydrated to the most hydrated. Based on literature viscosity data for aqueous

Jan 1, 2005

By A. Khan

The effect of sulfur dioxide on collectorless and collector induced flotation of chalcopyrite was studied by cyclic voltammetry on a rotating disc electrode. Contact angle measurements were made to determine the effect of sulfur dioxide concentration and electrochemical treatment. The benefits of sulfur dioxide in enhancing the selectivity of separating chalcopyrite from complex sulfide ores are discussed.

Jan 1, 1996

By C. W. Parmelee

THE ideal fuel for burning ceramic wares is the one that, among other characteristics, has little or no sulfur. For that reason wood was long considered the most desirable fuel but its high cost has practically eliminated its used except in regions where it is very abundant or other circumstances warrant its choice. The fuels commonly employed are natural and producer gas, oil, and coal. The last named is undoubtedly the most important, not only in this country but abroad. Occasionally anthracite is used but the larger part is bituminous. The quality of the coal used depends on the kind and the value of the products being manufactured. For some materials, such as common brick, hollow block, etc., the quality of the coal is of less importance than in the manufacture of polychrome terra cotta, pottery, porcelain, etc. It is obvious that in burning clays that contain notable amounts of pyrite, marcasite or gypsum, as is the case with many common clays, the sulfur content of the fuel is of much less importance. The permissible amount of sulfur in the coal used will depend on the kind of product being manufactured. "A good sample' of coal commonly used in pottery ovens has something like this quantity of sulfur." PER CENT. Total sulfur 1.20 Sulfur in the ash 0.11 Volatile sulfur a 1.09

Jan 9, 1919

By A. Haldar

This study focuses on the flow characteristics of hypereutectic Al-Si alloys in thin sections. The pattern assembly consisted of spiral horizontal patterns, 6.25 mm (0.25 inch) and 12.50 mm (0.50 inch) in thickness with a common sprue. Al-Si alloys with silicon levels of 14%, 18% and 22% were poured with superheats of 60°C, 115°C and 170°C. It was observed that metal fluidity (in terms of flow length and metal velocity) increased with increase in silicon levels and superheat for both section thicknesses. It was also observed that, for a section thickness of 6.25 mm (0.25 inch), silicon level had more pronounced effect on the metal fluidity. For 12.50 mm (0.50 inch) thickness, both silicon level and superheat affected the metal fluidity. The surface hardness of the castings increased with an increase in silicon level of the alloys at the gate and the flow tip. Detailed study of the flow tip was also carried out with a view to understanding the effect of silicon level and superheat on undulated flow length, surface hardness and microstructure.

Jan 1, 2007

By Darrell Wilder

When designing excavation support systems in urban environments, it is often necessary to consider the effect of vertical surcharge loads from adjacent structures. Several methods are used in practice to establish the horizontal surcharge-induce pressure on the excavation support. According to the experience of the authors, these methods often seem to overestimate the effect of the surcharge and may have significant impact on the construction costs. This paper explores several of these procedures and provides a discussion as to the reasons for the differences in surcharge effect predictions between different procedures. It also provides practical recommendations for designers dealing with excavation support design.

Jan 1, 2006

By Fumihiko Sumiya, Kunihisa Katsuyama, Yuji Ogata, Yuji Wada, Yukio Katoh, Yoshikazu Hirosaki

In our previous work, the results of photographic observation using a high speed framing camera showed that the difference between precursor air shock wave velocity and detonation velocity was primary factor for the channel effect. It is assumed that the decreasing precursor air shock wave velocity can prevent the channel effect in charge hole.

Jan 1, 1996

By L. M. Demers, D. C. Kuhn

"Kuhn, Douglas C., and Laurence M. Demers. Effect of surfactant on basal and silica-induced eicosanoid production by the alveolar macrophage. Am. J . Physiol. 269 (Lung Cell. Mol. Physiol. 13): L165-Ll 70, 1995.-Infiammation and fibrosis subsequent to the inhalation of certain mineral dust particles has been suggested to result from the activation of eicosanoid synthesis by the alveolar macrophage (AM). To determine if surfactant modifies dust-induced generation of eicosanoids by the AM, we evaluated the effect of the surfactant lipid dipalmitoyl lecithin (DPL) on the production of eicosanoids by rat AM exposed to respirable silica dust in vitro. During the first 24-h exposure period, DPL alone significantly increased basal production of eicosanoids but completely inhibited silica-induced thromboxane A2 synthesis. In contrast, leukotriene B4 (LTB4 ) production was only partially reduced by DPL. During a second 24-h exposure period, LTB4 production in response to the highest dose of silica remained significantly elevated in the presence of DPL. Similar results were obtained when the surfactant preparation Survanta was evaluated. These results suggest that 1 ) DPL and Survanta independently activate AM eicosanoid production, 2) DPL and Survanta modulate the response of the AM to silica dust, and 3) L TB4 may be the most important eicosanoid mediator of the long-term effects of silica dust exposure on lung pathophysiology. THE OXYGENATED METABOLITES of arachidonic acid (AA) (here collectively termed eicosanoids) have been implicated as important regulators of lung physiology and are thought to be involved in pathophysiological sequelae such as acute respiratory distress syndrome, asthma, and the pulmonary complications of sepsis (20). This role is manifested through both direct effects on lung physiology as well as through an indirect modulatory effect on the release of other mediators of lung injury, in particular profibrotic cytokines such as the interleukins and tumor necrosis factor (15). Recently, exaggerated eicosanoid production by both the alveolar macrophage (AM) and the type II epithelial cell has been demonstrated to result from the exposure of these cells to several particulates, including crystalline silica (quartz) dust (5, 9, 17). These observations have led to the suggestion that eicosanoids play a major role in the etiology of pneumoconioses.Another secretory component of the pulmonary environment, surfactant, has been shown to modulate crucial AM functions, such as bactericidal activity and the recruitment of circulating immune cells (25). Indeed, an important feature of the lung's reaction to inhaled mineral dust is an increase in surfactant production, perhaps as a compensatory or protective response (1, 16). In addition, the alteration of the surface properties of mineral dust by surfactant or its components has been shown to influence the biochemical response of the AM to the dust, perhaps by altering the surface charge of the dust particle (11, 29, 32). And recently, Wallace et al. (28) have shown that the coating of mineral dust with surfactant, and its subsequent removal by lysosomal phospholipase, unmasks differences in dust cytotoxicity that are not apparent when AM are exposed to uncoated dust. Thus it appears that the inclusion of surfactant in in vitro exposure studies may be important in evaluating both the absolute levels of eicosanoid production by the normal and dust-exposed AM and the temporal relationship between dust exposure and the production of inflammatory mediators by the AM. Therefore, we characterized the effects of the surfactants dipalmitoyl lecithin (DPL; the primary lipid component of natural surfactant) and Survanta (a commercially available surfactant derived from bovine lung) on basal and silica-induced AM eicosanoid production during two 24-h periods after exposure to dust particles to both allow the enzymatic removal of surfactant from the particle surface and evaluate the k"

Dec 1, 1996

By H. Polat, Q. Hu, S. Chander

"The collection efficiency of dust particles was determined in a laboratory dust chamber equipped with a water spray. Measurements were made in the presence of selected nonionic, cationic and anionic surfactants. For the nonionic and the anionic reagents, efficiency was maximum in a narrow range of concentration. The surfactant concentration corresponding to high collection efficiency was usually much below the commonly used concentration of l "", however. In comparison, much higher collection efficiency was observed for a cationic surfactant at extremely low concentrations. For delineating the mechanism of capture of dust particles, surface tension and contact angle results were used to obtain a correlation between the work of adhesion and the efficiency of collection. Such a correlation was reasonable for the nonionic surfactants but not for charged surfactants. In the latter case, electrostatic interactions between charged droplets and particles were more important, especially for the cationic reagent. INTRODUCTIONSeveral methods are used to control dust in mines. These include: ventilation, foam, scrubbers and sprays. This article is concerned with improving the effectiveness of water sprays, which are widely used to remove dust particles during continuous mining, by adding small quantities of surfactants. Water sprays produce small droplets which act as collectors of dust particles suspended in air. Sprays directed at the actual source of dust have the additional property of wetting the coal before the ·particles become airborne (Hamilton, 1974). Wetting agents, also called surfactants, arc known to play an important role in many applications where dust is a problem. However, conflicting reports exist in the literature with regard to the effectiveness of surfactants in water sprays (for a review, see Chander et al., 1988). In spite of the conflicting reports, the use of surfactants for dust control has increased over the years. In a recent study by the Bureau of Mines, a 27'6 reduction in respirable dust levels was observed in a mine test when surfactants were added to sprays (Foley, 1991)."

Mar 1, 1992

By H. Polat, Q. Hu, S. Chander

The collection efficiency of dust particles was determined in a laboratory dust chamber equipped with a water spray. Measurements were made in the presence of selected nonionic, cationic and anionic surfactants. For the nonionic and the anionic reagents, efficiency was maximum in a narrow range of concentration. The surfactant concentration corresponding to high collection efficiency was usually much below the commonly used concentration of l%, however. In comparison, much higher collection efficiency was observed for a cationic surfactant at extremely low concentrations. For delineating the mechanism of capture of dust particles, surface tension and contact angle results were used to obtain a correlation between the work of adhesion and the efficiency of collection. Such a correlation was reasonable for the nonionic surfactants but not for charged surfactants. In the latter case, electrostatic interactions between charged droplets and particles were more important, especially for the cationic reagent.

Jan 1, 1992

By Devin Burns, Saima Ghazal, Michael Owusu-Tweneboah, Kwame Awuah-Offei

Trust in AI systems and the nature and amount of information about the system can influence decision-making. It is, therefore, crucial to understand how AI-powered monitoring systems (e.g., gas monitoring systems) influence miners’ trust and decision-making in emergency evacuation. This work focused on measuring the differences between how participants respond to a simulated underground mine emergency evacuation situation when warnings are represented as coming from a human or AI-based monitoring system. We also manipulated the amount of information participants received about the system, yielding a 2×2 between-participants survey design. The participants received an alert message about rising gas levels in a mine and provided a response on how they would react and reported their perceived safety. We also asked questions to assess their trust in, preference for AI over human-based gas monitoring systems, and whether they are willing to delegate the duties of underground gas monitoring to AI systems. The experiment results show the amount of information had a significant influence on miners’ trust and decision-making. The safety perception of participants based on age, number of children and ethnicity was significantly different from one category to another. This work provides valuable insights as the mining industry deploys AI systems to aid mine safety.

Feb 1, 2025

By K. Meshinchi Asl

In this study the effects of T4 and T6 heat treatments on microstructural characteristics of AZ91 alloy containing Rare Earth elements have been investigated. Formation of intermetallic Al1 1RE3 needle shape particles which have a good thermal stability reduces both formation of ß(Mg17A112) and discontinues precipitation in AZ91 alloy which are dominated at the grain boundaries and are responsible for poor mechanical properties specially in elevated temperatures. For AZ91-RE samples both T4 and T6 heat treatments led to a continuous precipitation of ß particles at the grain boundaries after aging. However, in AZ91 samples (with no Rare Earths) precipitation was discontinuous at grain boundary areas. This type of precipitation is one of the main reasons of poor mechanical properties of this alloy at elevated temperatures.

Jan 1, 2007

By Wu Y. H, Lu J. P

Slope stability has now become a practical tool in the design and oper- ation of open pits. The stability of rock slope depends on many factors, including not only structural geology, the existence of weak layers, ground- water, blasting and weathering, but also the virgin stress field. This paper presents an application of a numerical method to investigate the effect of the virgin stress on slope stability. The finite element method is employed to simulate the excavation of open pits. Redistributed stress fields in the slope of open pit are computed for several different virgin stress fields. Based on the redistributed stress fields, the shear force which tends to produce sliding of a rock mass and the frictional resistance to sliding are evaluated. The possibility of potential failure is assessed by the limit equilibrium method. The combination of the finite element method with the equilibrium method provides a powerful analytical tool for slope stability. The significant effect of virgin stress on the stability of slopes is shown by studying a typical case.

Jan 1, 1989

By V. D. Tathavadkar

Chromite ore is of immense importance for the extraction of metallic chromium and chromium chemicals. The mineralogy and crystal structure of chromite phase are therefore important part of our investigation on the extraction chemistry of chromium species. In this investigation, we have studied the effect of the processing parameters, i.e., the temperature and the oxygen potential on the microstructure and composition of mineral phases formed in the Cr2O3 ?Al2O3 -FexOy -MgO system. In particular the importance of the spinodal decomposition reaction is emphasized in the extraction of chromium as sodium chromite and sodium chromate. Experiments were carried out in order to study the differences in the crystallography of different chromite minerals. Phase equilibria in natural chromite minerals were investigated by calcining chromite mineral in air, argon, and 5% hydrogen + argon atmospheres over a temperature range from 200 to 1200 °C. The effect of the oxygen partial pressure and temperature on the phase constituents of the calcined product has been discussed. The microstructural changes were examined using scanning electron microscope (SEM) and the changes in elemental composition in different phases were analysed by electron probe micro analyser (EPMA). The results obtained from EPMA studies were used to calculate lattice parameter of the spinel lattice, and these values were compared with the values obtained from X-Ray powder diffraction data. On the basis of the experimental data, the mechanism of the spinodal decomposition of complex spinel phases is described under the influence of oxygen partial pressure and temperature.

Jan 1, 2000

By H. R. Manouchehri

Large variations in flotation characteristics of minerals have been observed in winter and summer in plant practices as a result of changes in pulp temperature. Variations in temperature may affect the quality for pulp and related process water through changes in dissociation of different chemical species within the pulp, as well as changing in gas and metal hydroxide solubility, reagent adsorption and its stability on mineral surfaces, water/pulp viscosity, etc. All of these affect the flotation characteristics of specific mineral to some degree or another. It has been observed in Cu-Pb-Zn and/or Pb-Zn sulfides flotation that sphalerite (ZnS) flotation is strongly affected by changes in pulp temperature. Plant practices have shown that at the both low, e.g., T <10-12°C, and high, e.g., T > 60°C, the recovery for copper activated sphalerite is dramatically dropped. Within this paper the effect of pulp temperature on flotation characteristics of sphalerite is brought into considerations and laboratory flotation tests were conducted in conjunction with surface and solution chemistry analysis to understand the effect of temperature on sphalerite recovery. The effect of temperature seems to be complex since the temperature affects both the physical (hydrodynamics) and chemical phenomena in the flotation cell. In fact all sub-processes in flotation, i.e., collision, attachment and detachment, are affected by changing in temperature. Experimental results indicating that at alkaline pH values, e.g., 8.5 to 10.5, the recovery for copper-activated sphalerite is dramatically reduced when temperature is below 10-12°C, which is in agreement with plant practice at Boliden?s Garpenberg plant in Sweden. However, results from other studies indicated that the zinc recovery is also considerably decreased at high pulp temperatures, i.e., 62°C and above.

Sep 1, 2012

By Hui-bin Wu, Rui Yuan, Yang Gu, Peng-cheng Zhang, Zheng-zhi Zhao

The corrosion behavior of three kinds of medium-Cr rolled steel pipeline steels in carbon dioxide collecting and transporting environment at different temperatures was studied. The results shew that the 5Cr sample was most affected by temperature. When the temperature rised from 30 °C to 90 °C, the corrosion rate increased from 0.12 mm/a to 1.87 mm/a, which was increased 15.6 times. The corrosion rate of 7Cr steel at 30 °C was similar to that of 5Cr steel. However, as the temperature increased, the corrosion rate rised slowly, increasing by 2.4 times at 90 °C. The corrosion rate of 9Cr steel was not obvious with temperature, and it was always below 0.06 mm/a. The thickness of the corrosion product film of the three samples gradually increased below 70 °C, and suddenly increased above 70 °C. This was related to the negative temperature coefficient of the solubility of FeCO3, and the thickening of the product film also affected the ion exchange of the cathodic reaction. An increase in the Cr content contributed to grain refinement and increased the proportion of the small-angle grain boundaries. More fine grains mean an increase in the total length of the grain boundaries, which could provide a diffusion channel for the free Cr element; on the other hand, the low-angle grain boundary structure was more orderly, with a lower free volume and lower interface energy. Under the combined effect of both, 9Cr steel and 7Cr steel had high volta potential and better corrosion

Oct 1, 2019

By Zhucheng Huang, Ronghai ZHONG, Tao Jiang, Jun ZOU

The method of reduction roasting and magnetic separation of low-grade, micro- fine disseminated refractory iron ore following granulation with coal produced unexpected success. Pellets of iron ore with diameter between 3 and 8mm were granulated with coal, bentonite and water. The raw pellets and reduction products were analyzed by scanning electron microscopy and x-ray diffraction. Results show uniformly distributed coal powders inside the pellets improved the kinetics of the reduction process and accelerated the reduction rate. Reduction time was higher at temperatures below 890℃, which resulted in the formation of substantial amounts of fayalite. When temperature was increased, micro- fine hematite was then quickly reduced to iron metal and the amount of fayalite decreased sharply. When pellets were reduced at 950℃ for 25min, reduction products with 56.73% metallization rate were obtained. After grinding and magnetic separation, a concentrate with 72.18% Fetot was obtained.

Jan 1, 2015

By B M. Washington, R R. Lovel, G J. Sparrow, M J. Fisher-White

"Work in CSIRO with several Australian ores has shown that?by heating a high-phosphorus goethitic iron ore and then leaching with caustic or acid, the phosphorus levels in the ore can be lowered to a commercially acceptable value of around 0.08 weight per cent phosphorus (P). With increasing heating temperatures up to 1300¦C, the extent of phosphorus removal increased. This is considered to be associated with mineralogical changes in the iron oxide phases in the ore during the heating.Little phosphorus was removed from four high-phosphorus goethitic iron ores containing 0.12 - 0.16 weight per cent P in leaches with boiling water. However, leaches with sulfuric acid removed ten to 20 weight per cent of the phosphorus and leaching with sodium hydroxide removed even more phosphorus to produce leach products containing between 0.08 and 0.12 weight per cent P from three of the ores.After heating at 300¦C, leaches at a low pulp density of 0.5 weight per cent solids with 1 - 5 M NaOH and 0.1 - 1 M H2SO4 gave leach products with 0.06 - 0.09 weight per cent P. The lixiviant concentration required and extent of phosphorus removal depended on the ore. At a higher pulp density of 25 weight per cent solids, leach residues with between 0.07 - 0.14 weight per cent P were obtained.More phosphorus was removed from ores heated at 900¦C. Leaches at both the low and high pulp densities, with 1 - 5 M NaOH and 0.1 - 1 M H2SO4, gave leach products with 0.05 - 0.09 weight per cent P. However, the lowest phosphorus levels were obtained after heating the ores at 1200 or 1300¦C and leaching with 1 M NaOH or 0.1 M H2SO4. Leach residues with 0.02 - 0.06 weight per cent P were obtained, even from leaches at the higher pulp density of 25 weight per cent solids. Leaching tests on heated samples under heap leaching conditions at ambient temperatures have shown that phosphorus levels can be reduced to similar levels to that achieved in an agitation leach within ten days.CITATION:Fisher-White, M J, Lovel, R R, Sparrow, G J and Washington, B M, 2013. Effect of temperature on removal of phosphorus from Australian Goethitic iron ores, in Proceedings Iron Ore 2013, pp 373-380 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By B. I. Routh

A STUDY of the effects of temperature on the gel strength of drilling muds is a natural outgrowth of the present era of deep drilling. The control of the gel solids&apos; is now considered important because it affects the wall-building qualities; the suspension of weighting material; the removal and release of sand, cuttings, and gas; and the control of cav-ing formations. With regard to the effect of temperature on gel strengths Herrick2 states: "Temperature variation within ordinary limits does not have much effect on yield points." Lewis, Squires and Thompson3 investi-gated one clay and found no marked change with temperature in either yield point or mobility. Reed4 found that potassium bentonite showed a great increase of gelation with increase in temperature and qualitatively there occurred a marked increase in viscosity upon heating. The apparatus used in these experiments consisted of a Stormer viscosimeter, Marsh funnel viscosimeter, rectangular and cylindrical shearometers, Mudwate hydrometer, and other minor laboratory equip-ment. The various methods of measuring viscosity and gel strength have been extensively described by Evans and Reid.5

Jan 1, 1938

By P. Somasundaran

Electrochemical properties of silicate minerals govern their behavior in processes such as flocculation and enhanced oil recovery that can occur at elevated temperatures. Knowledge of these properties as a function of temperature can be helpful in developing an under- standing of the role of these interfacial properties at non-ambient temperatures. Zeta potential of Sodium Kaolinite and quartz has been determined as a function of pH and temperature in this work. Both systems exhibited markedly different behavior at higher temperatures and also exhibited significant hysteresis. Results are examined in terms of possible dissolution of the minerals and surface reactions at different temperatures.

Jan 1, 1986