Search Documents

By A M. Nyembwe, A M. Garbers-Craig, R Cromarty

With the depletion of high-grade lump iron ore, concentrates have been identified as an alternative material for sinter making. Adding concentrates to the sinter mixture reduces sinter bed porosity and gas flow through the sinter bed. This will result in lower sinter strand productivity. A potential solution to this problem is to add concentrate in the form of micropellets. This study investigates the effect of concentrate and micropellet additions on the permeability of the sinter mixture. Permeability was measured on sinter mixtures containing ten to 40 per cent concentrates and micropellets at various moisture contents. The effect of concentrate and micropellet addition on the permeability–moisture relationship was examined. The results confirmed that the addition of concentrates into the sinter mix decreases the maximum permeability of the sinter bed. The incorporation of micropellets into the sinter mix reduced the permeability less than concentrate addition. The study also showed that the maximum permeability of sinter mixes containing concentrate is reached at the same moisture content as the sinter mixture without concentrate addition. For sinter mixes containing micropellets, additional water must be added to obtain maximum permeability. Parameters including the granule size, void fraction and angle of repose were also investigated to evaluate their effects on the sinter bed permeability.CITATION:Nyembwe, A M, Cromarty, R and Garbers-Craig, A M, 2015. Effect of concentrate and micropellet addition on iron ore sinter bed permeability, in Proceedings Iron Ore 2015, pp 69–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By L. E. Veki, S. M. Luukkanen, J. P. Karvonen, J. O. Leppinen

Today there is a consensus that xanthate adsorption on sulfide minerals is primarily controlled by redox reactions occurring at specific potentials on these semi-conductive minerals. Consequently, it is possible to control xanthate adsorption by controlling electrochemical conditions in the system by using oxidizing and reducing agents. The scope of this study was to investigate the possibilities to increase the selectivity of Cu-Fe-Zn ore flotation by applying electrochemical control in the conditioning of the flotation feed. In this work, mild steel grinding in a nitrogen atmosphere was used as the basis to provide a negative starting potential and minimize the amount of oxidation products on sulfide mineral surfaces. To study how different potential levels affect flotation results, a controlled conditioning procedure was utilized maintaining potential at a desired level by titrating the pulp with air. Xanthate adsorption kinetics during conditioning was examined by taking pulp samples for spectrophotometric analysis and laboratory flotation tests were conducted for samples that underwent the controlled conditioning procedure in the potential range of -200mV to +200mV vs. SHE. A clear correlation was detected between chalcopyrite recovery and the potential during controlled conditioning indicating that there was a constant increase in chalcopyrite recovery when the potential was shifted to more anodic values. It is possible that utilizing potential control in the conditioning stage, a smelter grade copper concentrate can be achieved directly in rougher flotation without cleaning stages. Conditioning in favorable conditions had significant positive effects on flotation selectivity of chalcopyrite. The improvement in copper concentrate grade being predominantly caused by the depression of pyrite. By applying the controlled conditioning procedure pyrite recovery in rougher flotation was reduced even low as under 1%, while in the tests without controlled conditioning, pyrite recovery varied between 7.5 – 65.7%. The result of this work indicate that affecting collector adsorption by electrochemical control in the conditioning stage can provide significant improvement in sulfide mineral flotation and industrial applications could lead to decreased chemical consumption, reduced equipment and maintenance costs.

Jan 1, 2018

By Andrzej Warczok

Intensive smelting of copper concentrate in Teniente Converter (CT) leads to the production of high grade matte and highly oxidized slag. Smelting slag is processed in Teniente vascular slag cleaning furnace. The slag composition and forms of copper affect the slag cleaning process and final copper content. Converting of high grade matte in Pierce-Smith converter faces some difficulties in proper slagging of iron oxides. Overblowing in copper making stage allows for slag liquidation but leads to high content of copper oxide in converter slag. Converter slag recycling into CT results in the increase of the participation of oxidic copper. Separate treatment of converter slag and its impact on the forms of copper in CT slag has been analyzed. Thermodynamic properties of a system and kinetic limitations pointed out the negative effect of converter slag recycling on the forms of copper and copper recovery in slag cleaning stage. Experimental results of slag cleaning tests in a crucible scale as well as microscopic examination of laboratory and industrial slag samples supported the above analysis and permitted to formulate recommendations of separate processing of converter slag. Keywords: copper, losses, slag, recycling

Jan 1, 2001

By Dagoberto Brandão Santos, Kairo de Barros Guimarães, Túlio Magno Füzessy de Melo

The effect of the cooling conditions on the microstructure and hardness of a Dual Phase hot-rolled steel 800 MPa strength was investigated. Simulations of the cooling conditions using a dilatometer were carried out from samples of a hot rolled coil with variations of the intermediary temperature from 620 to 740°C, isothermal holding time between 1 and 10 s and coiling temperature between 50 and 400°C. In addition, two CCT (Continuous Cooling Transformation) diagrams were developed to evaluate the effect of the isothermal holding time on the phase transformations of the remaining austenite. It was observed that the intermediary temperature has a strong influence on the kinetics of the phase transformation, as well as the isothermal holding time influences the amount of ferrite formed and, consequently, the final microstructure and hardness of the material. The coiling temperature did not cause significant changes in the amount and morphology of the ferrite, but a gradual replacement of martensite with bainite was observed, which, in addition to the self-tempering effect, contributed to the hardness reduction.

Oct 1, 2019

By F. Khomamizadeh

In this study the effect of solidification rate, T6 and T7 heat treatments on thermal fatigue resistance of A319 aluminum was investigated. Increasing of the solidification rate improved the thermal fatigue resistance of the alloy by refinement of the microstructure. The most sensible areas for thermal fatigue crack growth were the eutectic zones, T6 and T7 heat treatments improved the thermal fatigue resistance of the alloy by enhancing of the matrix resistance against the crack propagation. The slight reduction of the thermal fatigue resistance after T7 heat treatment is attributed to coarsening of the precipitates which reduces the matrix resistance.

Jan 1, 2005

By Ari Jokilaakso, Junjie Shi, Zhuo Chen, Pekka Taskinen, Xiang Gao

The amount of copper flash smelting slag has increased during the recent years along with an increasing slag-to-metal ratio. During slag tapping, some copper sulfide is mechanically entrained. As a result, it is necessary to recover copper matte from the slag by suitable methods. At present, the most common way is slow, controlled cooling in a transfer ladle. However, research on the detailed effects of slow cooling and the function of slag modification is rare. This paper described experiments that were performed at different cooling rates (0.5, 1.5, 3, and 7 °C/min), with and without additive. A detailed characterization of the copper-rich phase and its particle size was subsequentlymade using SEM-EDSmicrographs and image analysis software.With a decrease in cooling rate, the particle size of the copper-rich matte phase became larger. The addition of gypsum and carbon as a slag modifier affected the size of the copper-rich phase slightly, and its chemical composition was modified compared with the experiments without additive.

Jul 31, 2020

By H. Yoshida, H. Hatta, T. Suzuki

"The effect of the copper and magnesium contents and quenching rate during quenching on the age hardening behavior of 2000 series aluminum alloys was investigated. For the higher copper-containing specimens as conventional alloys, like AA2024, precipitation of the stable phases increased as the quenching rate decreased under the as-quenched conditions. The maximum hardness after the artificial aging of air cooled(AC) specimens was much lower than that of the water quenched(WQ)specimens. On the other hand, for the lower copper-containing specimens, coarse precipitation did not increase even in the case of the AC. The age hardening behaviors of the WQ and AC were very similar such that the maximum hardness and aging rate were almost the same. Many parts of the fine precipitates that increased the hardness were thought to be the GPB zone or fine S’ phase for the WQ and relatively coarse S’ phase for the AC. From the calculated CCT(continuous cooling transformation)diagrams, the lower copper-containing specimens could maintain the copper and magnesium in the solid solution state during the AC, so they could be quenched at a rather slower quenching rate like the AC.INTRODUCTIONThe 2000 series aluminum alloys, containing copper and magnesium as the major chemical components, are some of the well-known heat treatable aluminum alloys. These alloys have a high quenching sensitivity, thus the age hardening ability of these alloys decreases with as low quenching rate. To prevent the decrease of the age hardening ability, quenching is done by a method such as water quenching, which is not very efficient in an industrial situation, because the method requires such large equipment. For these alloys, reducing the quenching sensitivity helps them to be produced in a rather convenient way. For example, 6000 series alloys such as A6063 have low quenching sensitivity, thus they could be quenched by only air cooling just after extrusion and they do not need water quenching. Based on these reasons, investigations of these alloys with high copper and magnesium contents have been conducted in the past to find a way to lower the quenching sensitivity by adding transition elements such as manganese, chromium and zirconium (Kanno, Suzuki, & Itoh, 1986; Suzuki & Itoh, 1986; Kanno, Sakuma, Muromachi, & Watanabe, 1988). However, very few studies have focused on the quenching sensitivity of the lower copper and magnesium containing alloys because of their usage for structural components with high strength, and most of the past studies have used only the fast quenching method like water quenching. On the other hand, from our recent results, there is a possibility to lower the quenching sensitivity of 2000 series alloys with lower alloying elements. In this paper, the effect of the copper and magnesium contents with lower alloying elements and quenching rate, especially in case of slower quenching rate than conventional quenching method, on the age hardening behavior of the 2000 series alloys is investigated by the hardness measurement, structure observation and thermal analysis."

Jan 1, 2018

By E. S. Leaver

THE presence of soluble base metals in precious-metal ores usually precludes cyanidation as the best method of treatment. The laboratory experiments described in this paper show the possibility of cyanidation of gold-silver ores containing less than 0.5 per cent, of cyanide-soluble copper and the effect of zinc in the cyanide solution. PART I.-COPPER IN CYANIDATION The proposed process of cyanidation of precious-metal ores containing copper is based on the regeneration of about 80 per cent., of the cyanide used in the dissolution of the copper. The method of regeneration involves a combination of the sulfide and the acid precipitation of the copper and silver. The resultant solution is made alkaline with lime, and the gold is precipitated with zinc dust. Solubility of Copper Minerals in Cyanide Solution In order to determine the solubility of copper minerals, including metallic copper, under the usual conditions for cyanidation, experiments were conducted with synthetic ores. Each ore sample was prepared by mixing the particular pure copper mineral with barren sea sand. Both the mineral and sand were ground to pass 100 mesh before they were thoroughly mixed. The percentage of copper in each head sample was determined by direct assay, excepting the metallic copper sample, which was computed on weights before mixing. Table 1 gives the results.

Jan 1, 1929

By E. S. Leaver

THE presence of soluble base metals in precious-metal ores usually precludes cyanidation as the best method of treatment. The laboratory experiments described in this paper show the possibility of cyanidation of gold-silver ores containing less than 0.5 per cent. of cyanide-soluble copper and the effect of zinc in the cyanide solution. PART 1.-COPPER IN CYANIDATION The proposed process of cyanidation of precious-metal ores containing copper is based on the regeneration of about 80 per cent. of the cyanide used in the dissolution of the copper. The method of regeneration involves a combination of the sulfide and the acid precipitation of the copper and silver. The resultant solution is made alkaline with lime, and the gold is precipitated with zinc dust.

Jan 1, 1929

By Y. -H. Cho, J. -M. Lee, J. -G. Jung

The effects of copper on the microstructure and mechanical properties of ultrasonic melt treated Al-xCu (x=0, 4) alloys were investigated. The densities of alloys were increased and their grain sizes were decreased by UST. The hardness and electrical resistivity measurements revealed that the amount of solute Cu within Al matrix was increased by UST. Both the yield and tensile strengths of Al-4Cu alloy were increased by UST. The improved mechanical properties of Al-4Cu alloy by UST were probably due to the reduced amount of casting defects (e.g. pore), grain refinement, and enhanced solid-solution hardening of Cu.

Jan 1, 2014

By A. G. Doll

The Bond low energy impact (crushing) work index test is specified to be performed on rock specimens between 50 mm and 75 mm in effective diameter. NQ-diameter drill core, frequently used in mineral exploration programs does not meet that specification, it being 45 mm diameter or less. This paper reports the effect of performing the impact test on contiguous sections of HQ diameter and NQ diameter core, exploring the hypothesis that the contiguous intervals give equivalent results in spite of the core diameter difference.

Jan 1, 2012

By Zhan Zhang, Hiromi Nagaumi, Zhen Li

"Recently, the remarkable strengthening effect of ??-Al(Mn, Fe) Si dispersoids at both ambient temperature and elevated temperature were found by several researches. A large amount of dispersoids can be formed by applying special heat treatments and within a suitable range of chemical composition of AA3xxx alloys. In the present work, the influences of Cr addition on the mechanical properties and microstructures of the Al-Mn-Mg-Si alloys were investigated. The mechanical properties at ambient and elevated temperatures were evaluated by micro-hardness and yield strength. Moreover, the microstructures in as-cast and heat-treated conditions were quantitatively analyzed by optical and electron microscopes. Results revealed that Cr also had effect on the number density and volume fraction of dispersoids. Micro-hardness and yield strength at ambient temperature increased with the increasing content of Cr, and the Cr addition increased the yield strength at elevated temperature as well. Moreover, the creep resistance at 300°C improved dramatically with the increasing content of Cr.INTRODUCTION Traditionally, AA3xxx aluminum alloys were widely used in packaging, automobile and architecture industries, because of its good formability, excellent corrosion resistance and weldability. And AA3xxx alloys were considered as non-heat-treatable alloys. However, the strengthening effect of dispersoids in AA3xxx alloys was discovered recently (Li & Arnberg, 2003;Li, Muggerud, Olsen, & Furu, 2012; Li, Zhang, & Chen, 2016; Liu & Chen, 2015).Alarge amount of dispersoids could precipitate by a proper heat treatment.In order to further improve AA3xxxalloys, the composition of the alloys should be optimized. A few previous studies were reported to investigate the influence of compositions on AA3xxx alloys. Adding Mn element could enhance the precipitation of ??-Al(Mn, Fe)Si dispersoids and improve the yield strength(Muggerud, Mørtsell, Li, & Holmestad, 2013), as long as the concentration of Mn was under the solid solution limit. Fe decreased the solubility of Mn and accelerated the precipitation rate of ??-Al(Mn, Fe)Sidispersoids(Li & Arnberg, 2003), the yield strength and creep resistance at elevated temperature could increase with an optimized content of Fe(Liu & Chen, 2016). Mg element would affect the nucleation process of ??-Al(Mn, Fe)Sidispersoids by forming metastable Mg2Si(Hirasawa, 1975; Li, Zhang, & Chen, 2017a; Lodgaard & Ryum, 2000), metastable Mg2Si precipitated during heating process and promoted the precipitation of ??-Al(Mn, Fe)Sidispersoids, moreover, Mg provided solid solution strength for AA3004 alloys(Li et al., 2016). Si increased the volume fractionof ??-Al(Mn, Fe)Sidispersoids(Muggerud et al., 2013)and decreased the size of ??-Al(Mn, Fe)Sidispersoids(Li, Zhang, & Chen, 2017b). With the addition of Mo, the size of dispersoids became finer with a higher volume fraction, the volume percentage of dispersoid free zones was reduced. Elevated temperature yield strength and creep resistance improved due to Mo addition (Liu, Ma, & Chen, 2017).However, the effect of Crelements on microstructure and mechanical properties of AA3xxx alloys were rarely reported."

Jan 1, 2018

By Lifeng Yang, Xiang Zhang, Liang Yuan, Yonghui Wang, Bing Hou, Mian Chen, Rixing Zhang

Large-scale hydraulic fracturing technique has been widely applied to the development of shale gas reservoirs, where the interaction between natural fractures and critical fracture zones has substantial impact on the propagation of hydraulic fractures. Therefore, it is of significant importance to understand and experimentally verify such mechanism. To reach this end, tri-axial fracturing tests were implemented on 400mm×400mm×400mm block samples collected from Longmaxi shale outcrops. The interplay between hydraulic and natural fractures was investigated during the tests, factoring in the role of pump rate in affecting the created fracture network. Based on the experimental results, the critical fracture zone, defined as the weak formation zone nearby the wellbore created by staged pressure implementation that is observed rapid fracture propagation upon next stage of pressure increase, was thoroughly investigated. The analysis illustrates that given the high brittleness of the shale formation, abundant critical fracture zones are generated around natural fractures with pressure building up at a relatively low pump rate. As the pump rate increases, hydraulic fractures initiate and come into play with critical fracture zones, implying emergence of a large number of micro-cracks. A changing pump rate modifies the way of interaction between hydraulic and natural fractures and the subsequent formation of fracture network. Long term fracturing fluid injection with relatively low pump rate below the activation of critical zones is suggested. Also proposed is appropriate timing when applying a specific pump rate that will contribute to the improvement of hydraulic fracture propagation.

Jan 1, 2015

By P. N. Anyalebechi

The effects of a cross-hatched grooved mold surface topography, casting speed, and superheat on the morphology of solidifying shells of aluminum alloy 3003 have been characterized by a series of immersion tests. The cross-hatched grooves were 0.232 mm deep with wavelength or spacing between 1 mm and 15 mm. The shells solidified at casting speed of less than 10 mm/s on the 1 mm spaced cross-hatched grooved mold surface were fairly uniform with little or no localized variations in thickness. However, the propensity for non-uniform shell growth morphology was exacerbated by an increase in casting speed, melt superheat, and the wavelength of the cross-hatched grooves. This is provisionally attributed to their effects on interfacial heat transfer and wetting of the mold surface by the molten metal.

Jan 1, 2008

By S. Mohanta, I. D. Behera, B. Sahoo

"Run-of-mine coal contains particles of different sizes with different specific gravities, and when this coal is crushed, the amount of material present in a particular density class changes. This alters the washability characteristics of the coal, which affects the quantity, quality, and separation efficiency of the gravity-based coal washing process. The degree of difficulty in washing a typical coal at a particular specific gravity depends mostly on the amount of material occurring within ±0.1 specific gravity range, which is known as ‘near-gravity material’ at that particular specific gravity of separation. In this paper, two numerical indices, namely ‘near-gravity material index’ and ‘index of washability’, are used to quantify the distribution of near-gravity material in different density classes and to evaluate the degree of difficulty involved in the washing process. The results of this preliminary investigation indicate the uniform distribution of near-gravity material in all density classes for finer size fractions, whereas for coarser size fractions more near-gravity material is present in the lower density classes, making the washing process more difficult at a lower specific gravity of separation. IntroductionThe prime objective of coal beneficiation is to remove physical impurities as effectively and economically as possible. The beneficiation process includes various operations on the asmined coal to make it more suitable for enduse application without destroying the physical identity of the coal. There are several coal beneficiation processes, but gravity-based separators remain the most efficient unit operation for removing the undesirable gangue material from run-of-mine coal. These separators exploit the difference in density between coal particles and gangue particles to effect a separation. The feed is introduced into an aqueous suspension of ultrafine magnetite with a particular density. The feed particles with a relative density less than that of the suspension (clean coal) float to the top surface of the suspension, whereas particles denser than the suspension density (gangue material) sink to the bottom. When the difference in density between the particle and the aqueous suspension is large, the separation is easy, but when this difference is less the separation becomes much more difficult since the settling velocity of the particles is very low. This lower settling velocity increases the probability that particles that should report to floats report to sinks, and vice versa, hence increasing the amount of misplaced material. Therefore, the degree of difficulty in beneficiating a typical coal at a particular specific gravity depends on the amount of material occurring within ±0.1 specific gravity range. This is known as ‘neargravity’ material, also termed ‘near-dense’ material, at that particular specific gravity of separation."

Jan 1, 2016

By Takanori Kokubo, Kenta Suzuki, Tomohiro Sasaki, Toshiya Anami

"Previous work has shown that the strengthening Al-Mn alloys with copper leads to the formation of an undesirable reduction in recrystallized grain size. In this study the mechanisms of strengthening and recrystallization behavior in a continuously cast automotive heat exchanger fin stockof Al-1.1wt%Mn-0.5wt%Fe-0.3wt%Si with a0.3wt%Cu addition were investigated. Metallurgical analysis revealed that the Cu strengthening was dominated by the formation of dispersoid particles, while solid solution strengthening decreased with the Cu additions. This result is attributed to the decrease in the amount of Mn solid solution. The post brazing recrystallized grain size was reduced compared to that not containing Cu. It is postulated that the Cu addition leads to a decrease in the amount of Mn in solid solution which leads to a finer grain size. This effect is attributed to Mn in the aluminum matrix inhibiting boundary migration but allowing other grains to grow during heat treatment. The results are rationalized based on particle stimulated nucleation (PSN), wherein dispersoid particles are more likely to become active recrystallization nuclei during the heat treatment. The increase in the number of active dispersoid particles with Cu addition is correlated to the recrystallized grain structure.INTRODUCTIONImprovements in properties such as strength, braze ability and corrosion resistance in thermal fin stock alloys are all means to gain improved efficiency in heat exchangers particularly in automotive applications. While Al-Mn alloys dominate automotive heat exchanger fin stock alloy, even small chemical compositional changes can profoundly influence these properties (Kawaharaet al., 2004; Yoshino et al., 2009). The microstructure (particularly the grain size and shape) also plays a key role in determining the product performance and hence the thermo-mechanical processing (TMP) must also be considered. The casting method (typically conventional direct chill, DC, or continuous casting) significantly influences the properties in no small part due to the very different TMP routes that are used. Continuous casting is generally favored for fin stock applications as its higher cooling rate (which can be 2 to 3 orders of magnitude higher than DC casting) leads to finer as-solidified intermetallic particles and an increase in super-saturated solid solution elements (such as Mn)that are known to improve fin stock performance such as strength, braze ability(Okiet al., 2008)."

Jan 1, 2018

By M. Tadayonsaidi

The effect of alloying elements on the mechanical properties and thermal expansion of 336 casting alloy usually used as piston alloy which has low thermal expansion and very good high-temperature mechanical properties and good wear resistance was investigated. The mechanical properties and thermal expansion characteristic of samples with different combination of alloying elements, which enhance to reduce the cost of products, have been studies, The results show remarkable increase in the mechanical properties with increasing the amount of Cu and Mg, while are reduced with increasing amount of Ni, On the other hand, the use of eutectic aluminum alloy as 336 alloy with higher percent of Cu and Mg and lower percent of Ni are recommended for industry, due to economical viewpoint and satisfactory properties.

Jan 1, 2005

By Sevinc Yildirim, Cigdem Oruclus

"Metal-Porous Silicon (PS) based structures dipped in water show the direct hydrogen fuel cell behavior. The effect of the thickness of the cupper (Cu) film on the electrical properties of direct hydrogen fuel cell is studied by fabricating Cu/Porous Silicon/n-Silicon/Indium structures. PS samples were produced electrochemical etching of n-type single crystalline silicon with a resistivity of 1,25 Ocm and (111) orientation. The thin films of Cu with different thickness between 200 and 600 nm were deposited on PS surface by electron-beam technique. Investigation of the effect of Cu layer on the performance of the structure indicates that the performance parameters such as open circuit voltage (Voc) and short circuit current (Isc) strongly depend on the Cu layer thickness. It was observed that the divice with an 350 nm Cu layer exhibits the highest open circuit voltage (0,5 V), short circuit current (0,01 mA) and power density (10 W.m-2).IntroductionHydrogen is the most attractive and ultimate candidate for a future fuel and an energy carrier. Hydrogen is recognized as the environmentally desirable clean fuel of the future since it can be used directly in different types of hydrogen fuel cells [1]. In the past years, the rise in portable electronics requires the development of miniature fuel cells compatible with standard silicon micro fabrication technology. Most silicon micro-fuel cells have used the polyperfluo-rosulfonic acid membranes (Nafion R) as a proton exchange membranes (PEM) that is not really integrated with standard micro fabrication techniques [2-5]. The composite materials such as inorganicorganic hybrid materials (Nafion-silica, Nafion-borosiloxane etc) are next generation of proton conducting membrane [4-8]. But, fuel cells run on pure hydrogen gas, which can be produced with other energy resources. Hydrogen smallest atom and thus the H2 gas can leak easiliy. The application of hydrogen for power sources has been greatly restrained due to the lack of safe and convenient generation and storage methods.A kind of hydrogen fuel cells Metal-PS-Si structures used as an energy water directly. There is no need pure hydrogen. Cu-PS-Si Schottky-type fuel cells with as proton-conducting membrane and the thin-film cupper catalist and water as fuel, which are interesting for fabrication of lowcost miniature fuel cells. Generation of the open-circuit voltage and short-circuit current has been observed by Cu-PS-Si structure dipping in different hydrogen-containing solution."

Jan 1, 2014

By Pizhi Zhao, Jingwei Zhao, Zhenshan Liu, Yiheng Cao

"A new Al-Mg-Si-Zn alloy designed for automotive outer panel was trial-produced with industrial procedure. The final product shows a strong planar anisotropy. X ray diffraction analysis shows such strong anisotropy is caused by the dominating cube texture component in the final product. The reason for such high cube texture component was investigated by tracing texture evolution starting from the hot roll slab. It is found that certain cube texture components already exists in the hot rolled slab. The density of cube texture component shows as a wavy change through the following1st cold rolling, inter-annealing, 2ndcold rolling and solution treatment. This study shows that the cold rolling in the laboratory can well represent the texture evolution during the industrial production. The results obtained by lab rolling hints that change of second cold rolling reduction has weak effect on the planar anisotropy, when the gauge of hot rolled slab and final sheet are fixed.INTRODUCTIONWith the rapid progress of light-weighting in the automotive industry, aluminum sheets get more and more application as closure panel and structure parts. Recently the dominating alloy for outer panel is 6xxx series, containing the main alloy elements Mg and Si. The popular gradesareAA6016,AA6111, AA6022, and AA6014. These alloys still cannot satisfy the various requirements from automotive manufacturers. Most suppliers of automotive aluminum sheets are developing their own specific grades according to the customer’s demand. To increase the baking response, anew Al-Mg-Si-Zn alloy was designed, concerning the high combination energy between Zn solutes and vacancies formed during the quenching stage of automotive sheet manufacture. This combination is helpful to the precipitation of ß”phase during the paint baking (Wang, 2015,2016; Yan, 2014).The plastic strain ratio (r value)is a key index of the formability of automotive body sheet. A high r value means a good formability. The r values in different directions can be used to evaluate the planar anisotropy of the metal sheets. The trial produced Al-Mg-Si-Zn sheet shows a strong planar anisotropy with respect to r values. Since the r value is tightly related with texture, the texture evolution from hot roll slab (HRS) to final T4P temper was analyzed with X ray diffraction (XRD) to find the reason for the high anisotropy. Besides, the cold rolling reduction (CRR) was varied in the laboratory to modify the texture distribution, i.e., the planar anisotropy."

Jan 1, 2018

By A. Roca, V. A. Quezada, O. A. Benavente, M. Cruells

The leaching pretreatment of copper ores is widely used in the Chilean mining industry. Agglomeration and acid curing have been identified as the most useful pretreatments. Of these, acid curing was recognized as beneficial in the dissolution of copper minerals, even in sulphides such as chalcopyrite. Extensive acid curing times have an impact on copper extraction, generate a homogeneous acid distribution in the mineral bed and benefit the inhibition of aluminum-silicate minerals (acid consumers). This document describes some of the theoretical background and results regarding the effect of acid curing in a chalcopyrite sample with 74% purity according to Qemscan analysis and a 28.5% of total copper. Leaching tests are carried out at 25, 50 and 70°C, evaluating the effect of a pretreatment on the chalcopyrite dissolution. The original sample and products generated were characterized by X-ray diffraction analysis and Scanning Electron Microscopy (SEM). The performed experiments indicate a direct relation between the effect of curing time and temperature in copper extraction. 92% of copper can be extracted in a leaching at 70°C and with 15 days of curing. Elemental sulfur, jarosite and copper polysulfide (CuS2) have been detected in leaching products. INTRODUCTION The copper extraction from minerals is a technique that has been developed for hundreds of years in the world. In 2017, the largest copper producer was Chile, exported 5.5 million tons (COCHILCO, 2018). However, in order to preserve this production level means overcoming multiple challenges. In the case of the Chilean copper deposits, the average copper grade in 2016 was 0.65%, lower than the 1% declared in 2004 (Consejo Minero, 2018). This is mainly due to the deeper of the deposits reaching sulfide mineral zones, mainly chalcopyrite. Traditionally, these sulfurized zones ore are treated through concentration by flotation and subsequent pyrometallurgical treatments. However, for some copper companies it is complex to process by this alternative, due to the high costs and high rates of water consumption. The mineral resources of these companies are known as "low-grade sulfides" and do not allow, economically, the treatment of these minerals through concentration by flotation. This is how hydrometallurgy becomes an alternative for the treatment of this type of deposits. In addition, several companies have hydrometallurgical plants, which would allow the operational continuity of these plants.

Jan 1, 2019