Search Documents

By M. H. Farjadi, J. Azari

Cost analysis of chrome ore reduction is one of the important issues facing ferrochrome producers in today?s competitive environment. Much of this depends on quality and various ratios in the actual ore. The latter can have a direct bearing on electricity consumption and optimum efficiency of the furnaces. While the industry has been successful in reducing costs by designing larger and more efficient furnaces, the role of the optimum blend of ore has perhaps been given less emphasis. This paper will discuss the general specification and metallurgical characteristics of various chrome ores for producing high carbon ferrochromium on industrial scale. By analysing the results obtained from smelting, including chromium recovery and energy consumption, the determining parameters in total cost of ferrochromium i.e. chrome ore; reductant and energy consumption can be optimized. Our study is based on actual experiences obtained from Faryab Ferroalloy Plant over a period of approximately three years.

Jan 1, 2004

The reactivity of clay minerals and variety of these reactions are greater than any other known colloidal material. While it is acknowledged that clay minerals can cause problems in mineral flotation, the literature contains conflicting evidence, particularly with respect to the effect of clays on froth stability. It is well known that achieving and maintaining optimum froth stability is an influential factor in determining froth flotation performance. However, the presence of clay minerals in the ore is a major challenge to obtaining a stable froth. In fact, clay minerals could reduce froth flotation performance by both decreasing and increasing froth stability. The mechanism by which clay minerals affect froth stability is not fully understood and needs to be investigated further. In order to improve flotation performance, reliable knowledge of the effect of clay minerals on froth stability is essential which is discussed in this paper. Keywords: froth flotation, froth stability, clay, clay minerals

Sep 1, 2012

By L Basnayaka, N Subasinghe, B Albijanic

"It has been recognised that the presence of clay minerals in ores adversely affect flotation performance. In this study, changes in rheological properties of the flotation pulps under normal operating conditions were studied with additions of bentonite and kaolinite clays at various concentrations. Zeta potential measurements were also carried out to determine the changes in surface charge due to adsorption of clay particles. The results showed that bentonite clay adversely affects floatability of pyrite while kaolinite clay had a lesser influence on flotation of pyrite. The addition of Ca2+ ions to the pulp containing bentonite modified the rheological characteristics and in turn improved the pyrite flotation. It was also observed Ca2+ ions suppressed the swelling properties of bentonite and altered surface charge properties of bentonite clay particles. It has been shown that the flow index affected the ultimate recovery and it may provide a means to monitor flotation performance in routine plant operations.Citation:Basnayaka, L, Subasinghe, N and Albijanic, B, 2016. Effect of Clay Rheology on Flotation of a Refractory Gold Ore, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By E. Burdukova

Rheological measurements have found a wide array of applications in mineral processing research. Rheological properties of mineral suspensions are highly dependent on the mineral surface properties as described by DLVO theory, and the relationship between these properties and inter-particle interactions is well established. In this paper, rheological properties of mineral suspensions are used to study the differences in behaviour of isotropic talc and anisotropic zirconia minerals as a function of varying properties of the suspension medium, such as pH and polymer dosage, specifically carboxymethyl cellulose (CMC). It was found that the rheological tests when carried out in parallel with electrophoretic or point of zero charge measurements, clearly reveal differences between behaviour of the suspensions of isotropic and anisotropic minerals. These differences are further accentuated with the addition of carboxymethyl cellulose (CMC).

Jan 1, 2006

Extraction under very mild conditions - a few minutes at room temperature with poor solvents - yields results characteristic of surface properties for a variety of coals. Such superficial extractions preferentially remove long-chain aliphatic compounds. As coal becomes more oxidized, less of these yellow- colored compounds is extracted, forming the basis for a simple colorimetric test for coal surface quality. The fact that these aliphatic compounds are responsible for surface hydrophobicity is supported by good correlation between extraction results and floatability, which decreases with decreasing extractability. This extraction test is very sensitive to oxi dationb even the effect of heating for an hour at 100 C can be detected. A second extraction test using mild alkali conditions has shown good correlation with plant dewatering Operations.

Jan 1, 1986

By F. Melo, M. Pawlik

Fine coal aggregation in concentrated coal-water suspensions was studied through steady-state rheological measurements. The wettability of coal particles was modified by dry oxidation of a bituminous coal. The degree of hydrophobicity was monitored using film flotation. The rheological measurements revealed that hydrophobic coal particles aggregate in aqueous suspensions, over a wide pH range, and produce slurries with high yield stresses. As the degree of coal oxidation increases, the coal particles become more hydrophilic and such suspensions exhibit lower yield stresses values. The yield stress values for suspensions prepared from oxidized/hydrophilic coal become a strong function of pH and correlate well with the surface charge as determined through electroacoustic measurements. These results indicate that the yield stress of aqueous suspensions of coal, and hence coal particles aggregation, is strongly affected by the wettability of coal particles.

Jan 1, 2004

By K. L. Cashdollar, C. K. Man, J. R. Gibbins

Oxyfuel combustion is currently one of the principal technological options being considered for capturing carbon dioxide from pulverised coal power plants. In oxyfuel combustion, coal is burnt in a mixture of recycled flue gases and added oxygen instead of in air. In principle this yields a flue gas containing only carbon dioxide, water vapour and small amounts other impurities. Oxyfuel combustion is superficially similar to combustion in air, but there are inevitable differences. This paper describes ignition tests on pulverised coal suspensions using a suite of coals of different rank and from different countries of origin and over a range of oxygen and coal concentrations of interest for oxyfuel combustion. The ignition tests were carried out using the National Institute for Occupational Safety and Health (NIOSH) 20-litre explosion chamber. The purpose was to determine how easily the various coals ignite and burn in mixtures of O2 and CO2 compared to their combustion in air. The residual char volatile and ash contents for the ignition residues were measured using a thermogravimetric analyser (TGA), allowing Q factors (i.e., enhancement in apparent volatile yield due to higher heating rates and/or heterogeneous reactions) to be determined and compared. An ignition index has been derived from the explosion and char data. This index has been used to rank low volatile coals for ignition propensity in air. The results show that to obtain ignition and combustion comparable to that in air, the oxyfuel O2-CO2 gas mixture must contain over 30% O2. Keywords: CO2 capture, combustion, pyrolysis, oxyfuel.

By Shunli Z, Jin X, Guanzhou Q

Flotation behaviour can be controlled, due to diminishment of granula quality and extension of specific surface area, by adding coarse particles (high- grade concentrates) to condition pulp. It has been substantiated that coarse particles can intensify fine particle flotation and its mechanisms are effects of carrier, intermedium and assistant aggregation of coarse particles. Calculation and analysis of Reynolds numbers and their variation for different size particles, under specific turbulent dynamic conditions, reveal that agglomeration among granulae is subject to specific turbulent dynamic conditions. Furthermore, sizes and adhesion strength of flocculated particles are the function of specific physical and chemical factors. Based on this research an innovative ramification carrier flotation process has been developed, which has been applied to Fankou Lead- Zinc Mine, Guang Dong province, China, etc, with satisfactory results. These results shed light on distinction between conventional flotation and fine particle flotation, meanwhile, provide a basic approach for further solution of fine particle flotation problem.

Jan 1, 1993

By Jean Viana Bahia, Antônio Adel dos Santos, Vicente Tadeu Lopes Buono

During cold rolling of Cr-Mo alloyed DP steel, considerable oscillation of thickness may occur. The literature points out that such occurrence is due to non-uniform cooling of the coil after the hot rolling process. Since the austenite transformation in this steel continues after coiling, the microstructure and, consequently, mechanical properties are very susceptible to natural variations in cooling rates associated with distinct positions of the coil. The influence of coil cooling conditions on thickness oscillation during cold rolling was evaluated in this work by using both industrial experiments and dilatometer tests. It was verified that an industrial coil presented large variation of mechanical properties associated with its heterogeneous microstructure. Consequently, thickness oscillation occurred during cold rolling. Dilatometer tests simulating hot run-out table and coil cooling showed that the austenite transformation is very slow under small cooling rates that occur after coiling. Thus, the slow transformation rate makes the coil very susceptible to environmental conditions around it during its natural cooling and is responsible for variation in mechanical properties of the coil. To ensure the formation of a more homogeneous microstructure in the whole coil, it is necessary either to make use of technologies that improves the cooling uniformity or to adjust the steel alloy design. The latter alternative has been done with relative success by using conceptions with lower amounts of Cr and Mo.

Oct 1, 2019

By M. Roy

Coke combustion during sintering process is significantly governed by coke breeze size distribution, which in turn affect sinter quality i.e. sinter granulometry, Tumbler index, Reduction Degradation Index and Reducibility Index of sinter. To know the effect of microfines of coke breeze on sintering process parameters, pot sintering tests were conducted and it was found that when microfines are eliminated and optimum coke size (1-3mm) is used yield of sinter increased by more than 7%. Similarly productivity increased by 9%, the strength of sinter i.e. ISO Tumbler Index increased by 2.3% and +10mm sinter size increased by 5.5%. Controlling of microfines during crushing and by improving crushing index will result in improved quality and productivity of sinter with lesser amount of coke breeze. This paper describes that how to optimize solid fuel i.e. coke breeze consumption in sintering process through granulometry control. Keywords: iron ore sintering, coke breeze granulometry, productivity of sinter, quality of sinter

Sep 1, 2012

By M. Kitazume, H. Imai

The deep mixing method was developed in Japan and put into practice in the middle of 1970s. Since then, the wet and dry type methods have been applied for various improvement purposes in Japan. One stork of mixing tool produces a column shape of stabilized soil in a ground. By the series of productions, arbitrary shape of improved ground can be constructed by overlapping each columns. It is specified to complete the overlapping within 24 hours in order to ensure the tight connection of the columns. However, it can not be completed within the specific time in some cases due to bad weather or machine trouble, which causes a cold joint in the improved ground. In this study, the influence of the cold joint to the behavior of the block type improved ground is examined by a series of centrifuging model tests and FEM analyses. It is found that the ground behavior is influenced by the position of the cold joint, where the cold joint at the sea side shows a little influence to the behavior but one at the port side causes large decrease in the stability of the improved ground.

Sep 8, 2021

By M. G. Maruma

The effect of the amount of cold reduction and annealing temperature on the evolution of the texture of AISI 441 steel is reported. The steel was cold rolled by 62%, 78%, and 82%, followed by isothermal annealing of each sample at 900°C, 950°C, and 1025°C for 3 minutes. The crystallographic texture was determined by Phillips X?Pert PROMPD texture diffractrometer. Microstructures were characterized using optical microscopy and scanning electron microscopy (SEM).The results show that sample that received 78% cold reduction and annealing at 1025°C presented the highest Rm-value and lowest ?R-value, which would enhance its deep-drawing capability. In addition, this sample showed the highest intensity of shifted ?-fibre, notably {554}<225> and {334}<483>. It can therefore be concluded that the ?-fibre, which favours deep drawing, is optimal after 78% cold reduction and annealing at 1025°C.

Jan 1, 2013

By Nathanael Wagner Sales Morais

Os aços maraging tem grande importância tecnológica devido sua aplicação nas industrias aeroespacial e nuclear. Uma das aplicações para esse material é a fabricação de cilindros de alta resistência pelo processo de estampagem profunda, logo o conhecimento da textura cristalográfica torna-se fundamental. Este trabalho investigou o efeito da laminação à frio seguida por um recozimento sobre a microestrutura, textura e anisotropia plástica no aço maraging 350. A anisotropia foi medida pelo cálculo dos coeficientes de Lankford e dos coeficientes de anisotropia normal (Rm) e planar (?R). Os resultados mostraram o aumento na deformação a frio gera um aumento na intensidade da fibra acompanhada de um aumento no valor de Rm. As análises metalográficas mostram que maiores reduções induzem à um precipitação intermetálica após o recozimento.

Aug 8, 2018

By H. Huang, H. M. Chen, W. B. Xie

Cu-0.8Cr-0.1Zr alloy were prepared by atmospheric melting. the microstructure and properties of the CuCrZr alloy after first cold rolled, solid solution, second cold rolled and aging treatment were analyzed by using optical microscope, electrical conductivity analysis and Vickers hardness tester. The results show that with the increase of the first cold rolled deformation, the grain breakage becomes more serious, and the cold hardening becomes more obvious and the hardness increases. The conductivity and peak hardness of the first cold rolled (reduction of 30% and 60%) alloys after solution, secondary cold rolled and aging treatment reaches 81 %IACS and 187 HV, respectively. However, the conductivity in the CuCrZr alloy with a higher rolling degree (reduction of 90%) after solution, secondary cold rolling and aging treatment is significantly higher, and the conductivity and peak hardness is 85.8 %IACS and 178 HV, respectively. INTRODUCTION CuCrZr alloy has been widely used in domestic industry for its excellent comprehensive properties such as high strength and high conductivity, especially in the contact wire and lead frame of high-speed railway (Sun, Tao, & Lu, 2015; Mishnev, Shakhova, Belyakov, & Kaibyshev, 2015; Zhang et al., 2016; Fu et al., 2017). In recent years, a lot of research has been done on how to improve the strength and conductivity of CuCrZr alloy. However, the high strength and high conductivity of copper alloys are contradictory characteristics. On the one hand, the addition of alloying elements is conducive to solution strengthening and aging strengthening; on the other hand, too much alloying elements in copper alloys cause defects in the lattice of copper matrix, resulting in a serious decline in the conductivity of copper alloys (Martienssen & Walirmont, 2005). How to obtain high strength and high conductivity at the same time is the main problem. At present, the main research methods are adding microalloying elements, thermomechanical treatment and severe plastic deformation to study the electrical conductivity and mechanical properties of CuCrZr alloys. For example, Xie et al. (2011) added trace Ag to the Cu-0.26 wt%Cr-0.08 wt%Zr alloy, and the size of precipitated phase Cr and Cu4Zr became smaller and the mechanical properties of the alloy were improved. Su, Dong, Liu, Li, & Kang (2004) found that the addition of trace Mg in CuCrZr alloy inhibits the growth of precipitated phase and reduces the internal stress around the precipitated phase. At the same time, the size of precipitated phase becomes smaller and the peak aging strength of the alloy is improved. Pang et al. (2013) found that adding trace Ni and Si to the CuCrZr alloy could improve the peak hardness, softening resistance and precipitation morphology of the alloy. Experiments shows that the grain size was significantly refined by equal channel angular extrusion combined with aging treatment, while the strength of the alloy was increased, and the electrical conductivity of the alloy did not decrease (Vinogradov, Patlan, Suzuki, Kitagawa, & Kopylov, 2002; Saray, 2016); Kermajani, Raygan, Hanayi, & Ghaffari (2013) showed that the strength of CuCrZr alloy can be improved by rolling at 500 °C. After 150 minutes of aging treatment, the strength and conductivity of the material increased to 431 MPa and 81 %IACS, respectively. Takata, Ohtake, Kita, Kitagawa, and Tsuji (2009) noted that the strain hardening, uniform elongation and tensile strength of the nano-precipitates produced by the mechanical heat treatment process can be notable enhanced. The mechanical and electrical properties of CuCrZr alloy can be improved by combining large plastic deformation with aging treatment in the test process (Gao, Huttunen-Saarivirta, Tiainen, & Hemmila, 2003; Huang et al., 2003; Xia et al., 2012; Zel’dovich et al., 2014).

Jan 1, 2019

By J. B. Yianatos

This paper addresses the impact on performance of column height (H), and column height to diameter (H/D) ratio by modelling the effect of HID on mixing and consequently on recovery and grade. Mineral recovery increases with increasing H/D ratio for a constant column volume and feed flowrate, while the concentrate grade decreases to a minor extent. Columns 10-15m in height with H/D-10 are well suited for feed rates 150-600 L/min. Maximum H/D is determined by the gas carrying capacity, an important consideration for pilot units where H/D?200.

Jan 1, 1987

By Diler Katircioglu-Bayel

This study aims to investigate the effect of combined mechanical and ultrasonic milling on the size reduction of talc. Firstly, the talc sample was wet ground in a stirred media mill for five different times (30, 60, 90, 120, and 150 min), and the optimum result was subsequently achieved with treatment by ultrasonication. The effects of amplitude (20, 35, and 50 μm), solid content (2.5, 5, 7.5, and 10%), and sonication time (60, 120, and 240 min) on the sizes of the final product were investigated. The pre-milling by wet grinding caused a decrease in the grinding resistance of talc. Sequential ultrasonic treatment, which was applied to the talc sample, generated smaller particles in comparison to those acquired by stirred media milling alone. Experimental results were assessed based on the product particle size (d10, d50), reduction ratio, and specific energy consumption. Submicron particles prepared by ultrasonic treatment were perfectly stable compared to stirred media milling alone as investigated in terms of particle size. In addition, the effects of mechanical and ultrasonic milling on structural properties of talc particles were characterized by XRD analysis.

By K. A. Lewandowski

Heap leaching efficiency is reduced by poor solution flow characteristics (channeling and ponding), which result from compaction and fines migration. Agglomeration of the ore can prevent compaction and immobilize fines, but copper leaching requires an acid-resistant binder to stabilize the agglomerates. Until now, there has not been a satisfactory way to evaluate whether a binder was effective, other than squeezing a handful to see if it ?feels right.? Procedures have been developed to quantitatively determine whether a binder produces agglomerates that can withstand compaction in an acidic solution, and have identified several binders that will provide sufficiently compaction-resistant agglomerates for copper heap leaching. Keywords: Copper heap leaching, Binder performance, Compaction

Jan 1, 2010

By Louis J. Demer, Paul A. Beck

As reported in a previous publication,1 isothermal grain growth in high purity aluminum and in an aluminum alloy with 2 pct magnesium can be adequately described by means of the empirical relation: [ ] or in some cases, by the simpler relation, [ ] Here, D is the average grain size after an annealing period t. The annealing period includes the time for complete recrystallization R, and the time for grain growth [to]. DA is the grain size as recrystallized, n is a parameter depending on the temperature and on the material. The effect of 2 pct magnesium in solid solution was to decrease D, and to increase R, A and n at a given temperature. The present work was undertaken in order to investigate the above listed effects of magnesium in solid solution, as functions of the magnesium content. The work also includes the study of certain anomalous effects observed in the recrystallization and grain growth of the 2 pct magnesium alloy at 350°C. EXPERIMENTAL PROCEDURE The method of producing the ingots used in this work was described in detail1 and need not be reproduced here. The materials used were high purity aluminum, furnished by the Aluminum Co. of America, of lot analysis shown in Table I and magnesium from a high purity distilled stock of magnesium crystals. [ ] Ingots were prepared for a series of binary aluminum-magnesium alloys of increasing alloy content. The numbers used to designate these ingots and their magnesium contents by chemical analysis are given in Table 2. [ ] The analyses showed no difference in composition between the top and the bottom of the ingots. Spectrographic analysis of the ingots for elements other than magnesium showed, within the limits of accuracy of the method, no increase in impurities over the amounts given in the lot analysis for the high purity aluminum in Table I. Careful microscopic study of ingot 21 in the as-cast condition, at magnifications up t0 1500X, revealed a cer-

Jan 1, 1948

By M. Silver, R. H. McCorkell

The effects of covering materials on radon emanations from uranium mine mill tailings were investigated. Granular materials with air in the spaces allow radon to pass freely. Moist covers of compost or soil decrease radon emanation from tailings. Water-saturated covers were more effective, and freezing the tailings with these covers further decreased radon escape. Water itself is a poor radon barrier probably due to circulation. Plants had no effect on radon emanation through soil. Although radon diffusion through water-saturated powders appears to be very slow and inefficient, about 25% of the radon escaping from the grains in water-saturated tailings diffuse to the surface and emanate when no cover is present. The radon escaping from tailings through covers of water-saturated compost or soil is no more than could be accounted for by radon produced in the covers themselves.

Jan 1, 1987

By Xiaoyan Xiang, Wenqiang Yang, Wentang Xia

Magnesium aluminate spinel is widely used in the metallurgical industry as refractory material, however, natural magnesium aluminate spinel is rare and most of the magnesium aluminate spinel is synthetic. The traditional synthesis of magnesium aluminate spinel often needs high temperature, which leads to more energyconsumption. In this article, solid phase sintering process was employed to synthesize magnesium aluminate spinel, in which, magnesium and aluminum oxide were used as raw materials and magnesium and aluminum powder were used as composite additives. The mass ratio of magnesium and aluminum on the effect of synthesis of magnesium aluminate spinel and the characteristic of the synthesis at different temperature and time was discussed. Experiment found that the synthesis temperature was observably lowered when the addition of magnesium and aluminum was 2.0% and 1.0% respectively.

Jan 1, 2016