Search Documents

By W J. Dyck

Past attempts to establish an integrated steel industry on the West Coast of Canada have been unsuccessful for at least three reasons: (a) insufficient reserves of a suit-able iron ore supply; (b) a relatively small local market for iron and steel; and (c) the non-availability of an economical process to produce primary iron on a small scale. Today, the reserves of economically mineable ore deposits are ample to support a steel production of 100,000 to 200,-000 tons per annum. The local market has increased so as to be able to absorb most of this capacity. With-in the next few years, a small integrated steel plant, including the "H-Iron" direct iron ore reduction process for electric furnace charge stock production, will be able to show a profitable operation. Introduction

Jan 1, 1963

By E. C. Wright

FOR many years the cost of making pig iron and steel in the Birmingham district has been about the lowest in the United States. The close proximity of the important raw materials such as coal, iron ore, limestone, and the large available scrap supply made it possible to assemble all of the important ingredients necessary for steel- making with only nominal costs for transportation. Both iron ore and coal were being mined in this district at one time for about $1 per ton from underground operations. At that time mining wages were low everywhere and the labor rate in the South was considerably below that of other mining districts. This situation persisted until the emergence of labor unions as an economic and political force, emigation of southern labor to northern plants, and continued growth of industry in the South in the years following the depression of 1932. Since that time union organizing of miners and steel workers throughout the nation has increased labor costs in mining and steelmaking. This influence has been felt particularly in underground mining operations since the proportion of labor cost to total cost is still high. The previous advantage in basic labor rate in the South has been almost entirely eliminated by the equalization of labor rates in basic industries by national unions. Since 1945 these influences have been especially noticeable in increasing the cost of mining coal and iron ore in the South. The northern steel districts are still being largely supplied with iron ore from the Minnesota open-pit mines and the cost of this ore has not increased nearly as much as the cost of ore obtained from underground mines in Birmingham. A similar situation exists in coal mining; the thinner seams in Alabama are not so amenable to mechanization as the northern mines and, as a result, the output per man-day in southern mines is only about three tons of coal as compared to five or six tons per man-day in the large captive mines of West Vir-

Jan 1, 1950

By P. M. Sullivan

A physical beneficiation flowsheet was designed by the Bureau of Mines for reclaiming and recycling metal and mineral values contained in municipal incinerator residues, and a continuous processing plant was installed. Residue samples collected from incinerators located in various parts of the country were processed at a rate of 1/2 ton per hour. Continuous screening, shredding, grinding, magnetic separation, and gravity concentration techniques were applied to produce metallic iron concentrates, clean nonferrous metal composites, clean fine glass fractions, and tine carbonaceous ash tailings. Research to develop systems for refining and upgrading the reclaimed metals and glass into marketable products is also underway. From the engineering data developed in the continuous processing plant, evaluations of the capital and operating costs for plants with capacities of 250, 400, 670, and 1,000 tons of dry incinerator residues per day were made. Research on a parallel system to separate and recover the metals, minerals, glass, paper, and plastics from raw, unburned refuse it currently underway, as are studies on the use of air classification to separate the refuse into organic and inorganic fractions.

Jan 1, 1971

By L. Rodd, C. Walker, T. Koehler

"The energy content of slag represents approximately 80% of the total energy inputs to a laterite nickel electric smelting furnace. Conventional slag handling methods produce only low grade heat and the entire thermal content of the slag is wasted. A heat recovery system proven on BOF slag in the mid 1980's can be adapted to a laterite nickel rotary kiln electric furnace (RKEF) plant. Slag is granulated using a high velocity air jet inside a waste heat boiler to produce slag granules. Granules are cooled during flight via radiation to water-cooled boiler walls and by convection to the granulation air. This system has the potential to recover 80% of the total slag energy in the form of hot air and steam.Integration of the recovered slag energy into the RKEF smelter can be achieved by a number of methods, including the use of preheated air at the ore dryers, kiln or existing power plant. Energy from the slag boiler may be used to reheat boiler feed water from the power plant or to produce superheated steam and generate electricity. The heat recovery system can provide up to 25 - 30% of the total electrical requirement of each RKEF line and a reduction in CO2 emissions of 234,000 tonnes per year.The total cost of slag heat recovery, including CAPEX and OPEX, is $2.5/GJ, which is competitive with using coal when CO2 credits are $18 per tonne. With Clean Development Mechanism (CDM) carbon credits currently selling at €13 ($20 USD) per tonne CO2, there is considerable opportunity for slag producers in regions including South America, Korea, Indonesia and Africa. Increasing fuel costs and more wide-spread legislation for GHG emissions will likely create conditions in which slag heat recovery could generate a favourable return on investment."

Jan 1, 2010

By James W. Estep

The sulphur shortage that has occurred in the past two years has directed attention more and more toward sour natural gas reserves, Wellhead values of sour gas vary widely depending upon the acid gas composition, location, market conditions, and necessary processing charges. Preparation of a saleable residue gas is considerably more involved and expensive than that normally encountered in treating a sweet gas. Recent revisions in sales gas specifications have increased capital costs and processing charges. The presence of hydrogen sulphide and carbon dioxide in a natural gas contributes to shrinkage factors that may approach 50%. Fuel required by the gas sweetening process and sulphur slant tail gas incineration also contributes to a further reduction in the volume of residue gas available for sale. The additional processing facilities involving gas sweetening, mercaptan removal, expanded utilities, sulphur recovery and sulphur handling, all demand additional operating and maintenance staff. A favorable sulphur market under certain conditions may justify the processing of sour gas whereby sulphur is either a by-product or a co-product, Five typical cases involving different compositions of sour gas are presented for evaluation. Capital costs, operating problems, and operating costs are presented in detail for full economic evaluation

Jan 1, 1967

By P. T. Allsman

INTRODUCTION The honor of being the recipient of the Mining Society's Daniel C. Jackling Award for 1966 imposes on me the responsibility to search for the subject that I would be best qualified to discuss. It seems that my experience in the mineral industry — nearly 15 years in private and 30 years in public employment — should uniquely qualify me to comment upon the relationships between the mining industry, mineral engineering as a profession, and government, and the changing economic, technologic, political and social changes that dictate their relationships. Such conditions, the increasing knowledge of the world mineral resource base, the greater demands of an expanding population with a rising standard of living, shall be evaluated with respect to our profession — mineral engineering. In all of these forty or so years, I have been in close touch with many phases of the mineral and energy resource industries, especially those of the United States. Particularly during the past 10 years, I have had a ringside seat at the "goings on" in Washington. During all of this period I have observed and analyzed many of the problems of the industry and its relations with the government. During the past few years, I have had increased opportunity for doing research and have found a need to learn something about the mathematical techniques that are undergoing such a revival since electronic computers were developed. One of these techniques is multivariate analysis, which is a system for correlating a large number of complex variables. By applying this technique to the seemingly chaotic present-day situation, there emerges a course of steady improvement in the minerals resource industries that wars, depressions, and political strife have failed to obstruct for long. In short, I advocate a need for new concepts in mineral engineering to cope with the changes, pos- sibly adding many more specialized areas on one end of the spectrum, and broad engineer-generalist approaches at the other. The meeting place shall be where the intricate mineral resource problems at the frontier of knowledge merge into the socio-techno-logical problems of the world. HISTORICAL INVOLVEMENT OF GOVERNMENT IN MINERAL RESOURCE PROBLEMS Involvement of government in mineral resource problems undoubtedly is as old as government itself. But passage of the Mining Act of 1866, superseded by the Act of 1872, was the first major entry of our Federal Government into the problems of mining. Passage of the law was necessary to resolve many conflicting claims and disputes in mining. The General Mining Law of 1872 and the Mineral Leasing Laws of 1920 apply to millions of acres of public lands and to certain privately owned land on which the mineral rights have been reserved to the Federal Government. The extensive involvement of government in the mineral industry business today often comes as a shock to the mineral engineer who has begun to climb the ladder to the top in his company. He is often poorly prepared to cope with the situation and becomes frustrated and even hostile. Better knowledge of the role of government perhaps would ease his situation. In our political system, private industry is responsible for producing minerals. To make certain that the production is adequate for a peace-time economy, and to guarantee the Nation's security in an emergency, the Federal Government finds it expedient to develop policy and engage in regulatory, educational, and research activities. A few examples will illustrate the varied role of government in relation to mineral problems. In varying degrees many agencies of the Executive Branch of Government have responsibilities that influence the functioning of the mineral and energy industries. In addition, of course, Congress, the Judiciary, and State and local governments exercise great influence. The Department of the Interior is primarily responsible for activities to promote the development and conservation of mineral and fuel resources, and the

Jan 1, 1967

By E. P. Pfleider

Important economic planning by industries, companies, financial firms and governments is predicated on estimates of future growth potential. Prior to the passage of the Taconite Amendment by the people of the State in November 1964, various admittedly conservative forecasts were made of the future of Minnesota's iron ore industry. Since that date, 3 new taconite plants are under construction, 2 are being expanded, one has just gone "on stream," and a seventh is in the design stage. These plants have a total capacity of about 35 million tons of pellets annually. The pessimism of 1964 today is being replaced by unbounded optimism. In the light of such recent developments, it becomes essential to update forecasts related to production, employment and capital investments. New projections show 50 to 58 million tons of pellet production from Minnesota by 1975. This tonnage, together with some 6 to 8 million of natural ores, should provide an annual full-time employment of 15,000 by the mining companies, plus 700 in related railroad and power producing activities and 1000 in plant construction. Total capital investment in new plants should reach $1.5 billion by 1975 and $2 billion by 1990. These current estimates indicate that the conservative goals as set in 1964 for the year 1990 should actually be achieved by 1975 or 1980. BACKGROUND Various forecasts1,2,3 have been made of the future consumption and production of iron ores within the United States. The most recent of these is by Harrison,1 delivered at the American Mining Congress meeting in Las Vegas in October. His estimates reflect the latest iron ore developments on a world wide front as well as the accelerating trend toward pellets. Minnesota's Natural Resources council prepared a detailed report in 1964 outlining the various factors that affect the future of Minnesota's iron ore industry. It presented estimates predicated on the

Jan 1, 1967

By I. M. Arbuthnot

Over the last five years, a large number of small to medium sized carbon-in-pulp gold treatment plants have been built in Australia, most designed to treat between 250,000 -1,500,000 tpa of ore. In many cases, the primary requirement was to get a plant built and operating in a short period of time and at minimal capital cost, relating to the limited capital resources and tight cash flow positions of these relatively small mining companies. Since the inclusion of both pre-leach and tailings thickeners resulted in an obvious and significant capital cost, most plants were built without thickeners, without doing a detailed cost-benefit analysis on their inclusion, However, the increasing use of High Rate Thickener?s (HRT s) in the mineral processing industries resulted in a reassessment, in some cases, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas, where borefields were costly to install and water was limited. It has become apparent, though, since startup and operation of these installations, that the savings in cyanide consumption is also a very significant factor and can be used as a primary justification for the installation of a HRT in many cases.

Jan 1, 1991

By K. G. (Ken) Thomas

"This paper gives an insight into the various processes available to treat gold ores. A brief overview is given of the various types of refractory gold ores. Particular emphasis is given /0 comparing the costs of oxide vs refractory gold ore processes, inclusive of grinding through to dore bar.HistoryThro ugh time gold has been recovered from the earth's crust by various mean s. Five major historical steps can be identified for metallurgical processing as shown in Table I .Gravity concent ration started with, for example, river bed panning and developed to more sophisticated processes such as the Johnson concentrator, belt concentrator and jigs. The South African gold fields were a major developer of gravity concentration processes during the first half of the twentieth century.As coarse free gold became depleted, stamp milling, in conjunction with amalgamat ion , was developed. Basically, rock was crushed under large mechanical hammers an d the gold collected in mercury . The mercury was then evaporated in a retort to leave sponge gold for further fire refining.As deposits became deeper and gold finer, the gold became more difficult to recover ; fine grinding was required to liberate the gold. In the 18905, MacArthur and the Forrest Brothers of Glasgow, Scotland, introduced the cyanide pro cess for dissolution of gold and its subsequent precipitaiton by means of zinc. This process, in vogue until the early 1970s, was commonly referred to as the Merrill-Crowe process for recovering fine gold .Activated charcoal was used as a means of recovering gold from solution in the 1880s, especially in chlorination plants in Australia( l). Two factors probably retarded the development of carbon instead of zinc-based processes during those year s. First , there was no satisfactory procedure for the elution of carbon to allow its recycling and, second, the development of the Merrill-Crewe process for gold recovery by zinc cementation probably discouraged any further work on the use of carbon"

Jan 1, 1991

By V. S. Sastri, Elboujdaini. M.

"Economics of wear in mining industry and methods by which wear cost may be reduced will be discussed.IntroductionCanada loses more than $5 billion annually due to friction and wear (Table 1). It is estimated that about $1.3 billion, or about 25% of the losses, could be saved through better application of existing technology (Table 2). It should be noted that the costs given in Table 1 and 2 refer to 1986. The losses due to friction and wear and the savings would be much higher in 1996. Tribology combines the many branches and specialties in science and technology concerned with understanding and combatting friction and wear. Specifically, tribology is concerned with the design and manufacture of sliding and rolling bearings, piston rings, gears, cutting tools and other devices in which surfaces interact, in sliding or other relative motion. Tribology is concerned with the correct use of materials for interacting solid surfaces, with the interaction of the surfaces with the lubricants, with the chemistry, physics and use of lubricants. It is concerned with the reduction of friction and wear and the avoidance of associated failures in machinery. Similar tribological components such as bearings are used in different technologies and similar tribological problems such as abrasive wear occur in different industries. Thus, tribology is in itself a generic science and technology, concerned with the generation and dissemination of knowledge on friction, wear and lubrication, and the application of the knowledge, to a wide range of industrial products and equipment, from ploughs to space equipment, from prosthesis to engines, from washing machines to railways, from computers to power stations, from paper mills to mines. Avoidable losses due to friction and"

Jan 1, 1997

By A. D. Dalvi

Economics, Resources, Environment and Technology are the major driving forces in the base metals industry. However, these factors are intertwined and together will propel the industry in the future. The demand for metals has grown with economic expansion, between 2 to 4 % p.a. The current growth cycle has been driven by economic expansion in China where the demand for base metals has risen from - 7 % of the world demand in the 90's to - 25 % of world demand today, and rising. Base metals are commodities and their demand and price are cyclical. Historically metal prices have declined in constant dollars, forcing the industry to reduce costs, increase productivity and increase the scale of operation for economies of scale. Due to resource depletion and capacity expansion the industry is driven to expand its reserve and resource base. However, in the case of sulphide deposits of copper and nickel it appears to be a losing battle. For nickel the laterites represent a vast source at this time. Their development requires development of new technologies to make these resources economic. Emission reduction is being increasingly mandated in most jurisdictions with all governments enacting progressively more stringent regulations. The industry has been responding with technological innovation. With the Kyoto protocol there is a push to reduce energy intensity in metal production. Technological innovation is driven by all the other factors and is leading to novel ways of doing exploration, mining and processing, that would maximize resource delineation and utilization, reduce costs, increase productivity, reduce energy consumption, maximize asset utilization and reduce environmental affects. Development of alternative technologies such as Pressure Acid Leach of laterite for nickel, bio-leaching, heap leaching, SX-EW etc are being adopted to achieve the aims of the industry.

Jan 1, 2005

Computers and other microprocessor technology lead the world of technological change. Nevertheless, the real advances in the world at large are not necessarily in the computer industry, but in the industries whose economics benefit most by the advances that this computer revolution makes possible. The minerals industry has always been in the forefront of this advance. Technological change in the era preceding the industrial revolution, and the mining industry's part in it, provides an instructive lesson for what is happening today. Strong parallels can be drawn for predicting future advances. With each technological advance allowing more efficient production comes a re-alignment of economics - absolute and relative changes to prices, to quantities demanded, and to other market characteristics. This re-alignment applies not only to the mineral industry, but also to the world at large. Adaptability, rather than technical advancement per se is the key to survival and growth in a changing world. 'Adaptability' as a concept is easy to support. As an operational philosophy it is not so easy to implement. As a goal for planning, it is much harder to quantify. A fixed scenario of a future world may provide helpful guidelines, but a scenario that demands adaptability to an uncertain future world is much less definite. Of course, everyone else in the world is also uncertain about the future, and they are making their plans using different assumptions. This virtually guarantees that our future will turn out different to our expectations. This is in part what Hayek (1945) calls the 'knowledge' problem. Until now, most of the planning and technical research undertaken in the world has ignored this problem. This ignorance is a luxury that we can no longer afford. The paper looks at the history of technological change and highlights the characteristics of successful technological revolutions. 'Adaptability' to unforeseen circumstances is the key to success in this environment. The paper examines the knowledge problem from the perspective of the mineral industry, and suggests a number of directions for maximising the returns from application of computer technology in this important area.

Jan 1, 1995

By M Scoble, R A. Hall

The mining industry has aggressively sought competitiveness through increased productivity and return on investment. A primary strategy has been the pursuit of economies of scale. This has also been dependent upon the implementation of new technology and systems integration. System integration has been accomplished through the implementation of mine dispatch, global positioning and mine wide communication technologies. These technologies have tended to advance at different rates of development and implementation. The result has been that across the industry, and even within companies, mines are at various stages of operational system re-engineering in these areas, driven by improvements in productivity and operational efficiency. Although this strategy has been successful, little effort has been made to analyse change in operational performance in order to understand and model the effects of scale in a quantitative manner. This paper considers the particular impact of equipment scale, together with potential future trends. It then presents and demonstrates a preliminary method to quantify through simulation the anticipated benefits of economies of scale.

Jan 1, 2003

By Thompson M

The humble gabion basket is to mine development what the light bulb and safety pin are to eir-ryday life. Gabions provide a flexible, easy to assemble and cost efficient solution for "101" mine and civil engineering development applications.In some instances gabion baskets are still efficiently in use after many years of faithful, maintenance-free service. In other situations, the baskets have been demolished or made redundant within days, either having served their temporary usefulness or negligently destroyed by the operator of heavy equipment. Either way, the gabion basket must surely rate among the top 10 cost efficient engineering construction materials.

Jan 1, 1994

By Daniel Connor, O&apos

The Cal-Sag Relief Sewer is a 2.6 m (8 ft 6 in.) diameter 9.1 km (5.7 mile) rock tunnel bored in dolomite for the Metropolitan Sanitary District of Greater Chicago. Included in the project are 18 shafts varying in depth free 70 m (230 ft) to 41 m (135 ft). This paper discusses how Healy/Vanessa reduced costs by eliminating conventional hand excavation by hoisting muck from a high production Robbins TBM (Tunnel Boring Machine) through small diameter drilled shafts and using a trailing rail-utility backup system.

Jan 1, 1985

By Kevin Sierra, Orfelinda Ávalo, David Martínez, Julio Guizado, Edwilde Yoplac

Los relaves mineros son un subproducto común del proceso de recuperación de los metales y los minerales. En general, consiste en un lodo líquido compuesto de agua y partículas finas de metales y minerales. En la actualidad estos relaves generan serios impactos ambientales provocados principalmente por su toxicidad, al reaccionar con el agua y el oxígeno. Existen diversos estudios que buscan alternativas para tratar estos materiales de manera ecológica para mitigar los impactos ambientales que puedan ocasionar.

Sep 29, 2023

By Patrizia Pereyra, José Rau, Maribel Guzmán

Las actividades mineras generan residuos que pueden impactar el medio ambiente y la salud humana. En Perú, la industria minera es una importante contribuyente al crecimiento económico del país, pero también genera una cantidad considerable de residuos. Este estudio investiga la geopolimerización de los relaves mineros de una mina de cobre a cielo abierto en Cajamarca, ubicada en el norte de Perú, como una solución sostenible para la gestión de residuos.

Sep 29, 2023

By Roberto Heredia Zavala

"El presente texto señala la posibilidad de interconexión de dos sistemas generadores de energía eléctrica, en donde la zona de influencia, carece notoriamente de agua potable para atender el consumo doméstico e industrial impuesto por el desarrollo de esta. Asimismo, La integración de los sistemas de generación de electricidad sería para el reemplazo del calor de los hornos con hidroelectricidad, haciendo así que el calor reemplazado se utilice en la desalinización de agua de mar y en consecuencia permita ia disponibilidad de agua potable para consumo doméstico e industrial. "

Mar 1, 1967

"La mina Rublo disminuyó sus costos de explotación mediante la aplicación de pastillas de carburo ""continental"" en la preparación de barrenos en el lugar mismo de la mina. Por tal motivo, el presente texto señala los datos obtenidos con la preparación de barrenos y la economía obtenida con este sistema. La preparación de barrenos consiste en un corte de la cabeza del barreno a través del un previo calentamiento, para luego ser derivado en una nueva cabeza, de manera que la superficie plana tenga una conexión del conducto de agua y que la forma requerida para la cabeza de este barreno sea en forma de Chaflán, a través de la barra de soldadura. Una vez conectado el conducto de agua, se cortan los rebarbados del barreno en los extremos del canal para la pastilla, obteniendo el ángulo exacto del barreno para la perforación. Finalmente, el canal para la pastilla es limado y cubierto con soldadura, colocando la pastilla en la soldadura y revistiéndola nuevamente para ser fijada en el barreno. De otro lado, los factores económicos -en tanto mano de obra y el costo de materiales-, no representan mayor costo en los barrenos, obteniéndose un precio menor de US$ 2. 60, a diferencia de los barrenos anteriores. Así, la reconstrucción de los barrenos resulta fácil y barata a través del uso de pastillas de carburo de tungsteno ""Continental"", evitando problemas de roturas o de soldadura. "

Jul 20, 1959

By U. K. Custred

Who We Are Farmland Hydro (FHLP) is a Limited Partnership formed by Farmland Industries, the largest U.S. farmers’ cooperative, located in Kansas City, MO, and Norsk Hydro, a large Norwegian company engaged in fertilizer, petroleum and the specialty metals industry. Both of our parent companies have a long history of commitment to the fertilizer industry. This year, Farmland Industry celebrates its 71st year in the business, and Norsk Hydro celebrates its 100th operating year! We employ approximately 300 associates in Central Florida. What We Do Farmland has been active in Hardee County, FL since the 1970’s as a large landowner and citrus grower. We plan to expand this activity into phosphate rock mining. The phosphate rock produced here will be shipped to our nearby chemical fertilizer complex in Polk County, where we produce quality phosphate products - liquid and granular fertilizers. Of the phosphate rock mined, 90% is used to make fertilizer. Other uses include animal feed, vitamins, medicine, light bulbs, soft drinks, film, flame resistant fabric, optical glass, toothpaste, bone china and other consumer products.

Jan 1, 2000