Search Documents

By Eurípides do Amaral Vargas Jr., J. A. de Mello Franco

"It is frequently necessary to excavate a tunnel for Civil Engineering purposes, or wells for petroleum exploitation, in laminated rock mass like schists or phyllites or in highly foliated gneisses. The determination of the pre-existing in situ stresses is essential, in order to assure the stability of these excavations. In most cases, the pre-existing triaxial stress field is arbitrary in relation to the tunnel or well axis. For these rock masses the concept of Generalised Plane Strain can be correctly utilized.There are closed form solutions for the calculation of stresses in anisotropic rock masses under Generalised Plane Strain conditions (Lehknitskii, 1981 and Hong , 1994). Based on these analytical solutions, established for the cases of Generalised Plane Strain, a synthetic problem will be formulated: the theoretical in situ stress tensor acting on this rock mass will be determined, with the aid of Bayesian Inverse Problem Techniques, as developed by de Mello Franco (2009). Additionally, the reliability of results obtained will be evaluated, in accordance with the research performed by this author. INTRODUCTIONThe Inverse Problem Technique, as developed in the paper, is based on the definitions and concepts obtained from the current literature and used for the solution of Inverse Problems, but the innovation to be presented is the utilisation of Bayesian Techniques and the determination of the reliability of the results obtained. This will be shown in a synthetic example where the determination of the in situ stress tensor, from strain measurements in a drill hole is supposedly performed. It is assumed that this drill has its axis arbitrarily placed in relation to the rock mass. Generalised Plane Strain conditions will hold for use with problem. The equations of Beltrami – Mitchel, in agreement to Lekhnitskii (1981) and Ong (1994), will be used in this synthetic case, for calculating strains, hypothetically measured in the hole before the final excavations. Finally a synthetic example for the determination of the in situ stress in a fully anisotropic rock mass, based on Bayesian Techniques and its reliability, developed in de Mello Franco (2009) is presented."

Jan 1, 2015

By V. Sheikhzadeh, M. Saghaeian, N. Esmaeili, R. Hejazi, A. Dehghani Ahmadabadi

High Pressure Grinding Rolls (HPGR) are mostly used prior to pelletising processes to increase the specific surface area (SSA) of iron ore concentrate. For expressing SSA, the Blaine index is utilised as one of the most important dimensional properties of iron ore pellet feed. ISO 21283 is a standard test method that explains the manual of Blaine air-permeability apparatus for determination of this parameter. In this standard, the disaggregation method is based on passing the minus of 1 mm samples from the 0.150 mm sieve. The disaggregation process has an effective role on the results of Blaine airpermeability test especially for regrinding HPGR products. In this research, firstly the Blaine index of samples was measured without disaggregation. Following this, disaggregation was done by passing the minus of 1 mm samples through three sieves with different dimensions, 0.150, 0.090 and 0.045 mm, separately, and the Blaine index was calculated for each one. Finally, lab-mill with rubber balls, called Jar mill, was investigated as another option. Screen analysis and image analysis with SEM were performed to evaluate the effects of the sample's disaggregation on the size distribution and agglomeration of samples. The results showed that the disaggregation method with sieve size 0.150 mm, according to ISO 21283, was not applicable for HPGR products because the particles were still stuck together. In addition, the disaggregation method with the sieve size 0.045 mm or with Jar mill offered reasonable results. Keywords: Disaggregation, Blaine index, specific surface area, regrinding HPGR, ISO 21283, Jar mill

Jan 1, 2020

By A. Bruynesteyn

The results of a 2 phase evaluation program designed to determine the amenability of an oxide ore from the Butte, Montana mine of the Anaconda Company to a sulfuric acid leach is presented. In the phase 1 preliminary evaluation, using roll tests and percolation leaching in small columns, it is shown that the ore is highly extractable at low acid consumption ratios. In the phase 2 confirmatory tests in large columns on l-l.5 tons of material, the amenability of the ore to the leaching process is proven and pregnant solution grade profiles from planned commercial heaps established.

Jan 1, 1978

By G. Deschênes

Following a successful investigation on the Central Zone sample, a cyanidation study was conducted on an ore sample from the AD-MW Zone of Clarence Stream Property, owned by Freewest Resources Canada, to develop a leaching strategy to extract gold. At a grade of 6.48 g/t, gold is present in the forms of aurostibite, free gold and electrum. The ore contains 4.3% berthierite/gudmundite, 1.3% pyrrhotite, 0.7% pyrite, 0.07% stibnite and 0.9% arsenopyrite. Similar to the Central Zone, the extraction of gold from the AD-MW Zone can be performed at atmospheric pressure, pH 10.5 and with a low concentration of cyanide. The grind size had no effect on gold extraction between a P80 of 28 to 71 µm. The oxygen and cyanide requirement significantly increased with a ?ner grind. Consequently, a very close control of cyanide addition is required to minimize passivation of gold. Lead nitrate, added in the pretreatment, increased the extraction of gold by 2.3%. Leaching at pH < 10 improved gold extraction but increased the cyanide consumption by 5%. Passivation of gold occurred when the pretreatment was longer than 2 hours. A longer pretreatment reduced the cyanide consumption by 5%. Mineralogical characterization of the leach residue with no gravity pretreatment prior to leaching indicated the presence of unleached gold grains and passivated gold grains. Removal of coarse gold by gravity increased the extraction by 2.8% (leach residue at 0.74 g/t Au). Increasing the DO to 16 ppm or the lead nitrate from 500 to 1,000 g/t increased the overall gold extraction to 90.4% (leach residue at 0.62 g/t), which is the maximum gold extraction obtained. The leaching parameters were 800 ppm NaCN, DO 16 ppm and pH 10.5 for a duration of 120 hours. The associated cyanide consumption was 4.0 kg/t. Gold leaching was not sensitive to cyanide concentration. Reducing the cyanide concentration to 250 ppm resulted in a gold extraction of 89.5% with a cyanide consumption of 2.6 kg/t.

Jan 1, 2009

By Norman F. Schulz

The Davis magnetic tube concentrator is a laboratory machine designed to separate a small sample of pulverized magnetic iron ore into magnetic and non-magnetic fractions. It was developed in 1921 by mechanization of a test previously performed manually. (1)(2)(3)(1) No significant changes have been made in the design of the apparatus since that time. The Davis magnetic tube test continues to serve as a practical basis for judging the amenability of an ore to magnetic separation and for controlling magnetic separation plant operations. The apparatus consists of an inclined cylindrical glass tube supported adjacent to closely spaced pointed poles of a powerful C-magnet. (Figure 1). To conduct a tube test, a sample of a suitably prepared ore is poured into the water-filled tube. With wash water flowing through, the tube is oscillated to gradually reject the weakly magnetic ore particles until the desired degree of separation is attained. Both the magnetic concentrate and the tailings may be recovered for examination.

Jan 1, 1963

By Bukeikhanov D. G, Syedin V. F, Sagyngaliyev K. S

The present paper describes a method of simulating deposits of com- posite structure by means of computers. The method employs mathematical tech- niques to study the openworks zone formation dynamics in open-pit mines with any mode of the works front ad- vance as well as to determine, on oriented graphs,the optimal direction of openworks expansion.

Jan 1, 1977

By M. Shamsi, M. Nehring

One of the most challenging aspects in semi-mobile in-pit crushing and conveying (SMIPCC) system design is determining the optimum depth at which to change from a purely truck-based haulage system to a conveyor-based haulage system. We used scenario analysis to determine the optimum transition depth between a truck and shovel (TS) system and a SMIPCC system. Traditional pit-limit algorithms were used to generate the final pit limit on a copper deposit, which was then divided into four pushbacks. The final operating pushbacks (phases) were designed for both TS and SMIPCC. The end depths for each phase are viewed as candidate transition points to switch from the TS to SMIPCC haulage system. Economic calculations were applied for five different scenarios, including adopting SMIPCC from the outset (pure SMIPCC), after the first, second, and third phases, and finally not using the SMIPCC system (pure TS) at all. The analysis indicates that the second scenario, at a depth of 335 m, results in the lowest cumulative discounted cost (CDC). In this case, the CDC is 17.6% lower than that for the pure TS scenario and 10.7% lower than for the pure SMIPCC system scenario.

Sep 1, 2021

By B. W. Cavender

The operating lifetime, or production rate, selected for a mining project is among the most important factors influencing the design and ultimate economic success of the project. An incorrectly-determined lifetime can lead to the erroneous rejection of projects as uneconomic as well as the suboptimal exploitation of producing properties. This paper examines the calculation of the optimal lifetime using both traditional discounted cash flow and recently-proposed option pricing techniques. Using each method, the production rate is determined as that rate at which the net present value of the project is maximized.

Jan 1, 1992

By M. Modis

According to previously established theoretical analysis and under certain conditions, a critical sampling grid can be determined for an earth-related space-distributed natural variable. Sampling above this critical limit adds little to the mapping results, while based on this limit the ideal process of reproducing the original phenomenon is theoretically defined. The objective of this paper is the application of the above theory to the Klidi lignite deposit in Florina, Greece, where Public Power Corporation (Greece) has conducted a sampling campaign to estimate the deposit thickness and its heating value. Data acquired for these two variables were analysed in the space domain in order to derive their respective correlation functions. The structural analysis of the deposit generated two covariance models, one for the thickness and one for the heating value, from which the critical sampling grid was identified. The conclusion drawn is that in some parts of the deposit the sampling grid is denser than required. Finally, an optimal sampling grid is proposed in order to gain the maximum information at the lowest cost.

Jan 1, 2006

By H. M. Howe

(New York: Meeting, October, 1913.) 1. INTRODUCTION.-This paper gives the results of our micro-graphic determinations of the position of Ae3 in a series of 14 hypo-eutectoid steels of varying carbon content, one of them very rich in phosphorus, and of SEe for one hyper-eutectoid steel. We have pro-ceeded chiefly by noting the temperature -at which the reabsorption of the pro-eutectoid element is found to be complete after a 30-min. holding, but in part also by noting the temperature at which its precipitation begins. Observations on these same steels by Messrs. Burgess, Crowe, and Rawdon, of the United States Bureau of Standards, are given in a paper&apos; issued simultaneously with this, while in a third paper s one of us compares these data with those of earlier observers. These three papers are treated as one whole by numbering their sections, tables, and illustrations continuously, and by setting the folding plates of micrographs at the end of the last paper. THE COMPOSITION OF THE STEELS EXPERIMENTED ON is given in Table I. Notation. and Definitions.-Following Osmond&apos;s development of Tschernoff&apos;s notation; in which " Ac3 " is the upper limit of the hypo-eutectoid part of the transformation range as observed in heating up, and " Ar3 " is that same limit as observed in cooling down, and following the usual custom of calling the upper limit of the hyper-eutectoid part of that range "SE," we may go farther and call this latter limit " SEc " when observed in heating up .and " SEr " when observed in cooling down.

Jan 6, 1913

By Lloyd R. Nelson

Selective carbothermic reduction is the preferred method of treatment of electric arc furnace (EAF) dust (listed hazardous waste, K061). The process maximizes the recovery of recyclable constituents by concurrent production of saleable zinc metal (directly condensed from the furnace off-gases), an innocuous, disposable iron oxide-rich slag, and some metallic iron. Results of a mineralogical investigation of a foaming slag produced during selective carbothermic reduction treatment of EAF dusts are presented. Wiistite and tricalcium silicate were identified by reflected light microscopy as the primary crystalline phases contained in a glassy matrix, but this technique failed to reveal any solid phases that could have significantly contributed to foam stability. It was concluded therefore, that the foam had been unstable, and had been primarily generated by copious gas evolution associated with the sudden reduction of the slag by an inadvertent addition of carbonaceous reductant. This is consistent with the susceptibility to foaming, when subjected to sudden excesses of carbon, of the slags produced by selective carbothermic reduction, because they still contain unreduced components such as iron oxide.

Jan 1, 1994

By E. Bakhtavar

Finding a ?practical spacing between the holes? for use of the expansive mortars is an important problem in dimension stone quarries. Objective has been to first introduce a relationship between this spacing and the dependent parameters in such a way that the required size and shape of the blocks is produced with the maximum efficiency and safety, minimum wastage, conservation of reserves and protection of environment. For this purpose, a dimensional analysis was used. On the basis of granite and marble rock types in Iran two separate relations are hence established to calculate the practical spacing between the holes.

Jan 1, 2011

By Charles A. Beasley

Increased technical and legislative analysis by all parties of interest could result in more efficientand better directed regulatory legislation in the mining industry. Efforts to forestall or frustrate legislation through massive lobbying and public relations efforts are seldom effective over time and often lead to more stringent and far reaching legislation than necessary. The Federal Coal Mine Health and Safety Act of 1969 is perhaps an outstanding example of such insufficiences; a future example may well be regulatory surface mine legislation. Although a lack of extensive hard data seldom enables rapid or sophisticated analysis early in the legislative process, even preliminary analysis may be sufficient. Simple statistical analyses of available data, assessment of the legislative rationale, and subjective appraisal of other non-quantifiable constraints to improved mine safety. An average of 115 underground fatalities at an exposure frequency rate of 0.67 can be reasonably expected in the immediate future, under existing levels of technology, degree of regulation, and economic conditions. If gross unrefined estimates of 6 preparation plant, 5 surface, and 30 strip mining fatalities are assumed, the total fatality industry level could be expected to approximate 156 Serious professional, economic, and technical constraints within the the industry probably preclude any major decrease of these accident levels within the near future

Jan 1, 1972

By William D. Gallant

This paper presents the results of a joint cooperative research project between the CANMET Cape Breton Coal Research Laboratory and the Cape Breton Development Corporation to observe the subsidence profile over the stopline of 2 West panel, Phalen Mine. A novel technique was designed and Implemented to determine vertical displacements of the overlying strata from within a near horizontal borehole drilled over the 2 West panel. Restrictions on data collection techniques due to the submarine nature of the coalfield are discussed. Development and implementation of the borehole technique using a piezometer and inclinometer Is described. Performance of the instruments and profiles obtained by them are presented and compared. Recommendations for design improvements are made to Improve the efficiency of the technique.

Jan 1, 1990

By P. J. Lunder, R. C. Pakalnis

This paper presents the results of research that has been undertaken in order to develop an improved method of determining the strength of hard-rock mine pillars. Pillars are found in various shapes and sizes in all underground mining operations. Prudent engineering design requires that if pillars are to perform as desired, both the pillar strength and the pillar stress must be determined. A detailed pillar stability study has been combined with an extensive database of published pillar case histories (178)resulting in a new “hybrid” pillar strength formula, “The Confinement Formula”, that utilizes classic strength of rock methods combined with empirical methods. “The Confinement Formula” utilizes a “mine pillar friction term” calculated from the average minor/major stress ratio with-in the pillar core. Statistically, the new formula provides better results at predicting pillar strength for the combined database than the best empirically ft pillar methods that currently exist. “The Confinement Formula” allows for the determination of the strength of mine pillars with an increased level of confidence over previously applied methods.

Jan 1, 1997

By Monika Patrycja Polak - Micewicz

This paper presents an approach for estimating the fatigue life for the base of powered roof supports (shield) manufactured by the FAZOS roof support company. FAZOS?s powered roof supports are designed to operate on an inclined coal seam in full caving with a medium, strong roof strength. This shield support is utilized in conjunction with a shearer and face conveyor for a complete longwall mining system. To design shield support, it is essential for contractor to know the physical (hardness, toughness, etc.) and mechanical properties of material (tensile strength, Young?s modulus, etc.) used for the shield support as well as the geotechnical properties of the mine site. The fatigue strength of the shield support material depends on the mean stress, alternating stress, cycle frequency, transport dimensions, mine environment and other factors. In order to estimate the fatigue life for a powered roof support system, it is assumed in this paper that the support must keep the roof stable in the mine under variable load cycles. The approach selected in this study contains Goodman?s model (Goodman, 1899) for all blocks in the design housing which is subjected to sinusoidal load. On this basis, the degree of fatigue damage was calculated and compared to the results of experimental tests. It will be shown that there is a significant detrimental effect on the fatigue life of the base of the powered roof supports due to geometrical notches. The Ramberg-Osgood model and damage accumulation rule (Palmgren-Miner) (Miner M., 1945) were used and numerical analyses were conducted, utilizing ANSYS finite element software. These analyses play a very important role in longwall casing design. The proposed method allows assessment of the yield state and forecast of the structure cracking, taking plastic strains occurrence into account. The presented method is universal and can be applied for fatigue life estimation of other subassemblies of powered roof supports. The final portion of the paper presents results of variable amplitude loading simulations on the S355N and S690Q steel used to make powered roof supports. The results of the physical tests were compared with the results from finite element methods. The proposed approach to calculate fatigue life gives the best correlation between the experimental results and calculated values of fatigue life for the powered roof support base. Finally, the design process uses a simple approach to predict fatigue life in a short time, reducing design costs and providing longer service life for roof supports.

Jan 1, 2012

The structure of the Bulli coal seam at Appin Colliery was detailed by the seismic reflection method. This unusual application of the seismic method was possible because there is a reflector near the seam as was revealed during exploration for petroleum in an area north-west of Appin. The reflector, which was at a depth of 1,500 ft, was shallow by normal reflection survey standards. Measurement of the seismic velocity at two ventilation shafts showed that the reflector was probably the Bulli coal seam. Accurate depth control was established from previous drilling results.INTRODUCTIONAppin Colliery, situated on the Southern Coalfield of N.S.W. (Fig. 1), is being developed to supply coking coal to the Port Kembla steelworks of Australian Iron and Steel Pty. Ltd. The colliery is mechanized and a detailed knowledge of structure, particularly faulting, is important in planning the workings.The Bulli seam, which is approximately 9 ft thick, and between 1,500 ft and 1,800 ft below the surface, is worked in the colliery. It is the uppermost member of the Permian Coal Measures and is overlain by Triassic rocks, which consist of thick sandstone beds containing beds of coloured shales, and which are subdivided into the Narrabeen Group, the Hawkesbury Sandstone, and the Wianamatta Group.In the early stages of development of the colliery, surface geological mapping and diamond drilling provided information on structure. Generalized results of the mapping are shown on Fig. 2. Drilling indicated that the physical and chemical properties of the Bulli seam are relatively constant, and that the seam is nearly horizontal, the average dipbeing about 1 in 25 to the west.

Jan 1, 1965

By F. Gordon Smith

ALTHOUGH several geological indicators of the critical type are known, including quartz inversions and decomposition of hydrous minerals such as serpentine, there are very few of the general type. Solid solutions are excepted, but the limitations of use are very restricted and interpretations are sometimes ambiguous. General methods for determining temperature and pressure conditions during the crystallization of minerals would have considerable scientific and economic value. It is not the purpose of this paper .to, discuss the various methods of geological thermometry and barometry, but to present one general method, applicable to all minerals, and to describe what progress has been made in the methods of measurement. The general method, in. brief, is a study of the stress conditions in and around various types of foreign inclusions which are trapped in minerals during growth. The method depends upon the fact that any homogeneous gas, liquid, or solid will in general have coefficients of thermal expansion and volume compressibility different from those of any given mineral. Therefore stress must develop in and around all types of inclusions in minerals if the temperature or the pressure, or both, are changed from the conditions which prevailed during the growth of the mineral. The methods of measurement consist of determinations of the temperature-pressure conditions of fit of the inclusions in the host mineral. The types of inclusions in minerals are: 1-gas, or liquid plus vapor, when observed at room temperature, due to crystallization under pneumatolytic conditions; 2-liquid, or liquid plus vapor when observed at room temperature, due to crystallization under hydrothermal conditions; 3-glassy solid, or devitrified glass, due to crystallization under magmatic or high temperature metamorphic conditions, in a siliceous liquid; and 4-crystals, due to overgrowth of other minerals crystallizing simultaneously or of other minerals which crystallized previously. A survey of the literature shows that much valuable earlier work on inclusions, especially that carried out in England in the last century, has dropped out of current knowledge. The following is a brief summary of the significant, contributions to the problem up to the present day. Davy in 1822 asserted that fluid inclusions in minerals consist of an aqueous solution of salts and a gas bubble, the whole being either at lower or higher pressure than atmospheric.1 At intervals from 1823 to 1862, Brewster contributed information concerning other types of inclusion consisting of 1-aqueous solution, a much more expansible liquid, and a gas; 2-aqueous solution, salt crystals, and a gas; and 3-the very expansible liquid and a gas. The very expansible liquid fills the gas space between 20° and 30°C. Compression strain effects were seen around inclusions in diamond, topaz, and other minerals.2-6 Sorby in 1858 and 1869 further advanced the study begun by Davy, stating that fluid inclusions represent a sample of the mother liquor of crystallization and that the degree of filling of aqueous inclusions at room temperature defines the temperature-pressure relations during formation of the host. The degree of filling may be measured by determining the minimum temperature of filling of the inclusion by the liquid phase. The very expansible liquid in some fluid inclusions is liquid. carbon dioxide. The temperature at which salt crystals in fluid inclusions completely dissolve in the fluid is the minimum temperature of formation. Inclusions of glass or devitrified glass indicate crystallization from a melt. Inclusions of crystals in minerals are often centers of strain, which may be seen by optical effects or by radial tension cracks. Sorby realized that an analysis of stress-strain relations about inclusions could be used to provide precise data on the temperature of crystallization, but the matter was never pursued.7,8 Hartley (1876, 1877),9,10 Hawes (1881),11 Wright (1881),12 Johnsen (1920),13 and Holden (1925)14

Jan 1, 1952

By A K. Ghosh, J Chung, E Topal, M Asad

"Many open pit (OP) mines with considerable vertical extent are approaching the end of their life-of-mine; some of them are seeking the opportunity to make the transition from OP to underground (UG) mining. The decision on the best location for transition from OP to UG mining should be addressed at the strategic mine planning stage. Conservatively, the transition to UG mining is considered near or after the exhaustion of the reserve within the ultimate pit.However, if UG is evident and exclusively viable from the inception, defining the best location for the transition through a conservative approach may not be an optimal option to explore. This clearly establishes the need for a mathematical model that aims to maximise the project value and considers OP and UG mining with crown pillar (CP) requirement simultaneously. Underground mine layout varies from one UG mining method to the other, and consequently the variation in the location of transition is eminent. Thus, focus on the selection of UG mining method must be a part of this analysisThis paper presents an implementation of an integer programming (IP) based mathematical model that evaluates the changes in mining layout and the project value under possible variation in the transition point from OP to UG mining for stoping and block caving methods. An IP problem is a mathematical optimisation or feasibility method in which some or all of the variables are restricted to be integers. The outcome of the implementation reflects that mining strategies with OP transition to stoping and block caving methods generated higher values than OP-only mining strategy. The case study not only demonstrates the difference in mining layout for both stoping method and block caving method, but also reflects that a joint consideration of OP mining, UG mining and CP placement helps to achieve maximum project value and resource utilisation.Citation:Darbritz, J, 2016. Remediation of Wall Failure at Kalgoorlie Consolidated Gold Mines' Golden Pike Cut-back 2016, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 96–103 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Madhu. P, Srinivas. K

Measurement of thermal properties like thermal conductivity, thermal resistivity, heat capacity and thermal diffusivity for materials, it plays a crucial role in a wide range of various civil and electrical engineering projects, and many field applications like building’s basement, power generation, underneath soil heating, wastes from nuclear as well as thermal plants, and buried cables. Thermal conductivity of soil depends upon various geotechnical parameters such as type of soil, moisture content, particle size distribution, density, and compaction characteristics. Earlier studies, the measurement of thermal conductivity of soil by incorporating the heat source methods. Thereby expensive and time taken to conduct in laboratory as well as field measurements. The thermal conductivity is determined by fabricated probe and used in this work. Fabricated probe was calibrated with glycerin. The thermal conductivity of the soil increases as the water content and density increase because these factors are majorly influencing and water has a higher thermal conductivity than soil minerals, and grain to grain contact increases as density increases. therefore, Thermal conductivity is higher in coarser soils than in finer soils. The details regarding of this work as explained in this paper.

Sep 1, 2022