Search Documents

By Theodore von Rosenvinge

Large diameter (2.4 meter) drilled shaft foundations were installed to depths of over 62 meters through soil into Arkose bedrock for Connecticut?s Pearl Harbor Memorial Bridge (I-95 over New Haven Harbor). The project involved many ?firsts? including the first ?extradosed? cable-stayed bridge in the US, and for Connecticut, the deepest drilled shafts, the first use of a rotator to install shaft casing, and the first use of the Mini-Sid technology for rock socket bottom inspection. Design utilized both friction and end bearing for rock sockets. O-Cell testing was employed to maximize performance factors during design and to allow adjustments to socket lengths during construction. Favorable test results permitted a reduction in socket lengths and significant cost saving.

Jan 1, 2011

By Patrick K. Wong, Richard Kelly

"The variability in strength and compressibility of in situ deep soil mixing products can be greater than the variability of the natural soil. However, satisfactory performance can be achieved by careful construction and an appropriate QA/QC program. This paper presents a case study on the use of deep dry soil mixing columns to support several embankments over soft clay along a highway project. Post-construction settlement monitoring indicated that good performance is achieved where the acceptance criteria are met, except in an area with high organic content. Embankments with contrasting performance are compared to the quality control test results which comprised laboratory testing of core samples as well as in situ test results such as pull-out and push-in vanes and conventional cone penetration tests. Drawing on the performance results and quality control testing, discussions and guidelines are given on quality assurance acceptance criteria and construction control testing regime for future projects.INTRODUCTIONBetween 2008 and 2012, the largest deep dry soil mixing (DSM) contract during that time in the southern hemisphere was carried out for the Ballina Bypass project. The project, comprising 12 km upgrade of the Pacific Highway located in northern New South Wales close to the border of Queensland, was commissioned by the Roads and Maritime Services (RMS) of NSW. The ground improvement contractor was Keller Ground Engineering (KGE) Australia. Seven different types of ground improvement techniques were employed for the project, ranging from low embankment strategy with nominal preloading, to surcharge with wick drains, light weight bottom ash fill, DSM, vibro-replacement stone columns, dynamic replacement, and vacuum consolidation (installed by Menard Bachy Pty Ltd). Different techniques were chosen depending on time program, cost, and performance requirements relative to proximity to piled structures (e.g. bridge abutments) and post-construction settlement and differential settlement for either rigid or flexible pavements at different locations.DSM was the most utilized ground improvement technique employed on the project, comprising a total of about 285 km of 0.8 m diameter columns to depths up to 18 m for the purpose of supporting bridge approach embankments and culverts with embankment heights up to 6 m. DSM was chosen due to the very soft nature of the clay soil with moisture content practically at liquid limit, and the relative speed and economy of the system. Dry cement powder at rates of 160 kg/m3 to 200 kg/m3 were pneumatically discharged via the hollow stem of the mixing tool, and mixed with the soil (using multiple horizontally mounted paddles on a single vertical stem) at high speed as the mixing tool is withdrawn."

Jan 1, 2015

By Shuie Li, Taibai Li, Tao Hu, Zhongjie Wang, Xiang Ge

As one of the main power sources, lithium-ion batteries (LIBs) will continue to be applied on a large scale in the future market. Commercialized LIBs cathode materials contain various valuable metal elements including Li, Co, and Ni. The development of green and efficient recycling technology is essential. Deep eutectic solvents (DESs) have recently emerged as a new class of green solvents that could potentially be applied for the LIBs recycling industry due to their capability to leach the active materials without the introduction of environmentally hazardous reagents as used in conventional hydrometallurgy process. Considering the rapid progress, a critical review focusing on the progress and fundamentals about the overall efficiency has practical significance for the further advancement of this field. Herein, we briefly introduce the overall process of using DESs for LIBs recycling and specifically focus on the efficiency of each step. Current fundamental understandings and new experimental approaches to enhance the efficiency of the leaching process, the extraction process, and reusability are summarized. We expect this review article to inspire scientists to use DESs as powerful tools for advancing the frontiers of LIBs recycling.

Jul 30, 2022

By Pathik Deb Mallik, Shyamal K. Mitra, Rajiv Kishore, Shuvranshu Rout, Manos De

"This paper presents a case study on the design and construction of a deep underground pit structure constructed inside almost a century old existing plant building. The complexity and challenge for the design and construction lay in executing the work in a difficult subsoil condition especially the presence of deep mica schist. The limited space availability in the existing plant for construction work without hampering regular production in other adjoining areas of the plant made the execution more challenging. Experience with difficult subsoil and proximity to old foundations entailed a non-conventional engineering approach while ensuring complete safety in spite of maintaining the normal operation.INTRODUCTIONTata Steel Processing and Distribution Limited (TSPDL) is a subsidiary unit of Tata Steel Limited (TSL) having a CR processing facility inside the premises of Tata Steel Limited. TSPDL intended to install equipment for a new slitting line inside the existing shed including construction of very deep structure called “loop pit” where the strips from cut CR sheets collect in the form of loops and are recovered as scrap. The entire plant is located within the shed of existing plant. The construction of all foundations including the loop pit is to be executed in the limited area without disturbance to normal production work in balance areas of the plant and also maintain safety and integrity of existing structures.The existing shed is an old structure constructed approximately 80 years ago. The building column foundations are gravity type design of brick masonry supporting only the vertical load from the columns. This type of foundation designed with no eccentricity of loading provides no allowance for implementing any foundation stabilizing design. The present project required civil construction for the new equipment foundations safely within this area."

Jan 1, 2015

By M. Pernot

A 12 m-deep excavation has to be perfomed in the Shanghai soft clay to install an underground electric substation. This article was originally intended to study the behaviour of the wall, the excavation bottom and the surrounding ground during the excavation. Since the works are behind schedule, and the data referring to the excavations are not, therefore, available, the article is limited to a presentation of the analysis methods that we envisaged for the study of the behaviour of the excavation.

Jan 1, 2010

By Tariq B. Hamid

Deep excavation is commonly associated with construction of different deep below-grade structural elements (e.g., basement walls and slabs, tunnels, retaining walls, tanks, utilities, etc.) Deep Excavation Retaining Systems (DERS) are required when open cuts with safe slopes are not possible. Careful analysis, design, and planning of the DERS are required to provide safe below-grade construction and secure nearby structures from damaging effects that may result from the deep excavation. Selection and design of temporary or permanent DERS (e.g., soldier pile and lagging, sheet piling walls, secant pile walls, tie backs, etc.) can have significant impact on time, cost, and performance. In order to design DERS using conventional methods, it is necessary to obtain shear strength parameters, angle of internal friction (ø), and cohesion (c), of retained soils. Residual shear strength parameters (ø'res, c'res) obtained from drained direct shear tests and triaxial tests on saturated samples have been commonly used in practice for the analysis and design of DERS. However, there are cases where ground water table remains at or below the base of excavation during the design lifetime of DERS. In such cases, the soil above the ground water table is in an unsaturated state. Therefore, it is important to account for the unsaturated conditions of soils in order to optimize the design of DERS. This paper is focused on implementing the basic concepts of unsaturated soils mechanics including matric suction and soils-water characteristic curve (SWCC) to estimate design shear strength parameters of unsaturated soils (i.e., ø°, c', and ø') for the design of a cantilever sheet pile walls, a typical case of study of the DERS. The results of this study indicate that the determination of unsaturated soil strength shear strength parameters is simple. In addition, using unsaturated soil mechanics theories has an outstanding impact on the design of retaining systems.

Jan 1, 2006

By Brian Isherwood, Tara Brown, Paul Kreycir, Jenny Earle

"The Shangri-La hotel and luxury condominium tower, recently opened on University Avenue in downtown Toronto, required eight levels of underground structure, four extending into the shale bedrock.Isherwood Geostructural Engineers was retained in 2007 by Anchor Shoring Limited to provide an alternative design-build solution to better address serious foundation risks. The site, bounded on three sides by City streets, abuts an existing 1957 14-storey building with five underground levels to the north. Sitting on the rock surface along the east perimeter under University Avenue runs the existing Toronto Transit Commission’s University Subway Line built by cut-and-cover in the 1950’s and which was believed to lie very near the property boundary at the southeast corner of the site.The bedrock under Toronto is known to contain very high locked-in horizontal stresses, much higher than can be resisted by shoring techniques, which result in inevitable wall movement when excavating deep into the rock. The strategy adopted to control the risk to the Subway, adjacent building, and major utilities is described in the paper, along with the comprehensive monitoring of movements, and their comparison to predictions.The ProjectThe 66-storey Shangri-La hotel and luxury condominium tower, recently constructed on University Avenue in downtown Toronto, houses 222 hotel rooms in floors 1-17; 287 residences on floors 18-49; and private estates including two 2-storey penthouses on floors 50-66. These comprise 873,000 square feet of development. Eight levels of underground basement are required to provide parking and other amenities, the lower four extending into the shale bedrock."

Jan 1, 2015

By Richard D. Luark, Fernanda S. Madrona

Designing temporary retaining systems that allow for deeper excavation amid the existing urban infrastructure has become a challenge. A 60-foot-deep excavation in downtown Seattle was required to construct five levels of below grade parking for a 35-story high-rise building, Tower 12, next to an existing 20-story tower with three levels of below grade parking, separated from the project by an 18-foot wide alley. The solution was to combine two temporary excavation support systems, soil nailing and anchored soldier piles, to work within the site constraints. Densely-arranged, short-length soil nails were used to support the upper 30 feet of the excavation, while the lower 30 feet of the excavation was supported with soldier piles combined with steeply-inclined, high-capacity ground anchors, which extended below the adjacent building foundations. The combined temporary support system eliminated the need for internal bracing, reducing construction cost and schedule. The performance of the combined soil nail and soldier pile system was monitored with an inclinometer and optical survey monitoring, which demonstrated the performance of the combined temporary support system. This paper provides a discussion of the advantages of combining different excavation systems and an analysis of movement monitoring data collected. SITE CONDITIONS AND PROJECT INFORMATION Tower 12 consists of a 0.45-acre development with 36-stories of mixed, residential and commercial use with four levels of below grade parking. The project site is bounded by the Cristalla Condominium to the north, Virginia street to the south, 2nd Avenue to the East, and an 18-foot wide private alley to the west. The One Pacific Tower Condominium, which has three levels of below grade parking, was located to the west across the alley. A site layout plan is presented as Figure 1. As shown in Figure 1, the construction of the west wall required a maximum 51-foot-deep excavation, from elevation (EL) 162 feet to EL 111 feet. Adjacent to the west wall, the existing alley grade varies from elevation 154 to 161 feet, leaving a narrow block of soil 18 feet wide and up to 42 feet high to be shored along the alley in order to reach the One Pacific Tower bottom of mat foundation at EL of about 120 feet. In addition to the existing One Pacific Tower Basement wall, site constraints included existing utilities along the alley such as an existing 4.5-feet wide by 7-feet high vault, with bottom at approximate EL 146 located 10 feet from the back face of the proposed Tower 12 basement wall.

Jan 1, 2019

By B. H. Moore

Foundation and excavation problems associated with lock construction projects vary widely. Each lock requires a different foundation to respond to a unique geologic setting. The range of heights and founding materials are illustrated thru description of selected structures encountered in the United States. Examples range from 113-ft high John Day Lock on the Columbia River founded on basalt rock to the 17-ft high Lock No. 5 on the Arkansas River floated on a clay foundation. A description of the basic elements of design and construction is presented. Several case histories involving lock design and construction are assessed to aid in recognition of potential problem areas on forthcoming construction. In the past decade there have been many improvements in construction materials and techniques. The application of these new approaches to lock construction is discussed.

Jan 1, 2010

By J. J. Hussey

"Abstract-The ""Brunswick Horizon"" an informally named ore-bearing unit near the top of the Nepisiguit Falls Formation in the Ordovician Tetagouche Group, hosts the Brunswick No. 6 and No. 12 base-metal mines, as well as the former Austin Brook iron mine, in northern New Brunswick. Detailed structural analysis of the No. 6 and No.12 mines led to the prediction that a massive­ sulfide deposit may have been repeated by F1 folding along the Brunswick Horizon. A subsequent drilling program discovered the new massive-sulfide North End Zone at a vertical depth of 1100 m, 1 km north of the No. 12 underground workings. By the end of 1990, Zn-Pb-rich massive sulfides had been delineated over a strike length of 200 m and a down-dip extent of 170 m. Rock units intersected in the North End Zone are generally thinner and vary somewhat from those at the Brunswick No. 12 mine. Thinning of the hanging wall rocks may be primary, may result from attenuation along F2 folds, or may represent truncation by a thrust fault. The newly discovered sulfide zone indicates that significant potential exists for the discovery of other deposits at previously unexplored depths.SOMMAIRE-Dans le nord-est du Nouveau-Brunswick ""l'horizon Brunswick"" est le nom usuel de la zone qui contient les mines de métaux de base Brunswick No. 6 et No. 12, ainsi que l'ancienne mine de fer Austin Brook, toutes situées sur le dessus de la Formation ""Nepisiguit Falls"" dans le Groupe Tetagouche d'âge Ordovicien. Une analyse détaillée de la structure des mines No. 6 et No. 12 à permis a van Staal de prédire qu'un gîte de sulfures massifs pourrait se répéter dû à une déformation F1, au nord de Brunswick No. 12. Suite à un programme de forage, la nouvelle zone de sulfures massifs appelée le ""North End Zone"", profonde de 1100 rn, et à une distance d'un km au nord des chantiers souterrains, fut découverte vers la fin de l'année 1990, les sulfures massifs riches en Zn-Pb ont été délimités sur une longueur de 200 rn et une hauteur de 170 rn le long du pendage. Les unités de roches intersectées dans le ""North End Zone"" sont généralement plus minces et sont quelque peu différentes de celles de la mine Brunswick No. 12. L'amin­ cissement des roches pourrait être primaire ou être le résultat de l'atténuation le long des plis F2, ou soit tronqué par une faille. La nouvelle découverte d'une zone de sulfures indique un potentiel énorme pour la découverte d'autres g ""tes à ces profondeurs inexplorées."

Jan 1, 1992

By Zharinov SE

Geonechanical modelling of island arc sys- tems and their analogs is investigated. Slow seismotectonic movements along the inclined deep fault zone under the compressive horizontal stress conditions are proposed to be the princi- pal mechanism controlling the structures and processes in the active continental margins. A model of shearing surface crack in an elastic half-plane is used for simulation. The main ele- ment of the model is viscous interaction bet- ween the crack sides, the viscosity varying with depth. To describe the stress-strain state of the medium an integro-differential singular equation is derived and solved numerically. The results of simulation are in good agreement with geological and geophysical data on the ac- tive continental margins.

Jan 1, 1987

By David C. Lager

While not a new construction technique "top/down" construction is seeing increased use in high rise building construction. Using diaphragm wall, drilled shaft and mining construction techniques, top/down construction enables construction of both the below grade basements and high rise structure simultaneously. To date the top/down method has been used on at least four major building projects in the United States. This paper will review the economic, engineering, construction and schedule issues associated with top/down technology on two projects -Olympia Centre, Chicago, and One Westwood, Los Angeles. Top/Down construction is currently under consideration on several additional projects in the United States.

Jan 1, 1987

By Zia Zafir

Design of the deep foundations for the loads imposed by lateral spread include the estimate of the pressure applied by the liquefied material as well as amount of anticipated displacement. In the absence of a non-liquefiable cover over a liquefiable layer, it is possible to design the foundation system just for the additional pressure applied by the flow slides. On the other hand, if a non-liquefiable layer exists above the liquefied zone, the foundation should be designed for anticipated movements. To completely account for liquefaction and/or lateral spread and their interaction with the deep foundation system, a coupled soil-structure interaction (SSI) analysis should be performed. However, a complete SSI analysis may not be feasible for most of the projects. This paper will present recent advances in analysis techniques and simplified methods to design deep foundations for liquefaction and lateral spreading. In addition, a case history of the Rancho California Bridge in southern California located within 1 km of the active Elsinore fault will be presented. One of the bridge abutments is underlain by potentially liquefiable layers. The pressure applied by the liquefiable layer was estimated to be greater than the shear capacity of the 36-inch CIDH piles designed for the abutment. However, with limited ground improvement and more careful analyses incorporating structural effects of CIDH piles, resulting design and construction resulted in a factor of safety greater than 1 against slope failure. The recommended approach was generally consistent with the recently published, and AASHTO sponsored, NCHRP 12-49 project regarding seismic design guidelines for new bridges and the effects of seismic displacements against bridge foundations.

Jan 1, 2006

By Satyajit A. Vaidya

This paper presents a case-study in the design and construction of deep foundation element supported mats for two residential towers on an18,000-square-foot site in Brooklyn, New York. Based on site sub-surface conditions, conventional mat foundations bearing on medium dense sand, having an allowable bearing capacity of 3 tsf, were originally anticipated for the 16 and 25-story towers. However, when the tower shear walls were relocated to the edges of the mat foundations due to architectural revisions, the significantly increased mat edge contact stresses applied to the soil subgrade resulted in calculated settlements of a magnitude that would adversely impact the proposed structures and the neighboring/bordering lot-line building and rail transit subway structures. To address this issue, deep foundation element supported mats were designed for the towers. The design was performed as an iterative process involving structural SAFE and geotechnical Plaxis finite element computer analysis to develop a coordinated geo-structural model of the foundation system. Initial presumptive design values of 45 pci and 445 kips/inch were used for the modulus of subgrade reaction and minimum deep foundation element stiffness, respectively. The designed foundation system consisted of 40 and 60-inch-thick mat foundations for the 16 and 25 story towers, respectively. Initially, the deep foundation elements were designed as 50-foot-long, 14-inch-diameter elements installed to sustain a maximum individual compressive load of 250 tons. The final deep foundation element design was subsequently refined to consist of a 48-foot-long, drilled and grouted IBO Titan 103/51 element designed to sustain a maximum load of 167 tons. Subsequent field load tests on the deep foundation elements confirmed element stiffness ranging from 1,040 to 1,530 kips/inch, with measured mobilized side shear of about 29 psi. The mat foundation reinforcement was adjusted for the pile stiffness values determined in the field load tests, and the deep foundation supported mats were constructed. The two towers were subsequently constructed, and have performed successfully.

Jan 1, 2010

By Douglas C. Brunot

Mabey Inc. is providing for the shoring design for the Naples bay Center project, located in Naples, FL. The excavation is approximately 374' long by 164' wide and is 27'-8" deep at the shoring line with a groundwater level six feet below present grade. The project Excavation is for a multi-use facility for residential and retail with underground parking. The shoring design will be incorporated into the foundation walls for the building. Mabey is using its pre-engineered Super Powerbrace Plus (SPP) wales and Mega Struts to support the excavation in two phases. The system design and the design of all the pre-engineered components are by Mabey. The foundation is supported on drilled shafts arranged with the building column grid. The excavation will be completed in two phases to allow for equipment mobilization and operation on a site with limited access. The construction sequence will begin with placement of the drilled shafts. The drilled shafts will also serve as the building columns. After the drilled shafts have cured, 630 AZ24-700 x 45 ft. long sheet piles will be installed. The sheets will be arranged in two phases, divided by a center row of piles. Since de-watering in south Florida is very expensive and often downright impossible prior to placing the seal slab, all the initial foundation and excavation bracing work will be completed with groundwater in situ. The entire excavation will be excavated to 5 ft. below ground surface to allow for the installation of the wale support brackets at 12 ft. on center, welded to the sheet piles. After the support brackets are installed, the SPP hydraulic wales and the Mega Strut hydraulic braces may be installed for both phases. Once the frames and struts are in place, Phase 1 excavation is completed, followed by Phase 2 excavation. The 4-ft. thick seal slab is then placed and cured in the wet. De-watering is now possible with the seal slab in place. Once the excavation is de-watered the leveling slab is placed and cured. The center row of sheet piles is then cut off at the top of leveling slab. With the leveling slab cured, the sheet piles have enough strength to support the excavation without the frames and struts near the ground surface. The permanent sheet piles are then seal welded for water proofing and the foundation walls are cast with the sheet piles. The design is modelled in 3D using REVIT to ensure accuracy of the design. The earth pressures are developed using Coulomb theory as there is a top frame and the frame and sheet pile are flexible and move to develop an active pressure wedge. Earth pressure uniform loads and loads from predicted surcharge are modeled in STAAD to determine load effects on the SPP frames and Mega Struts. Coulomb theory and Mabey’s structural model will be tested through monitoring with Mabey’s LIVEPin system. LIVEPin will be placed in struts for each phase of construction. The LIVEPin results will be calibrated with the structural model to determine actual frames forces and will also determine the actual earth pressures applied to the system from surrounding soil. Mabey has used the LIVEPin system in similar applications and this has helped us determine modelling accuracy.

Jan 1, 2018

By Peter Florian

At 5:50 am on October 1, 1992, the new $800 million Pittsburgh International Airport Midfield Terminal opened its gates to the world after five years of construction and more than 24 years of planning. Despite numerous design changes, this massive project was completed on time and substantially within budget. The importance of this airport to Allegheny County and the Pittsburgh region was recognized 24 years earlier by Allegheny County Commissioners Tom Foerster and the late Leonard Staisey. Staisey and Foerster established a program to acquire land for the "Airport of the Future".

Jan 1, 1993

By S. R. Nandargikar

Construction of open foundations for the Second Thane Creek Bridge was indeed a challenging task. Some major problems were encountered during the construction of foundations for pier No. P22 (S/N), P.6(S) and P.12(S) of this bridge. This paper describes these problems briefly and also highlights how they were solved.

Jan 1, 1996

By Martin Pratt

This paper is an overview of deep foundation engineering in Hong Kong past, present and future. The enormity of the subject compared with the space available makes brevity inevitable. Issues of construction and design are covered and some examples of recent challenging projects are given. The content is aimed at those with an interest in foundations generally, but with limited knowledge of the Hong Kong scene. Reference is made to informative publications for further reading on specific topics.

Jan 1, 2000

By James L. Vinson

Wilbur Smith Associates (WSA) has provided planning, engineering and construction oversight assistance to the Tennessee Department of Transportation (TDOT) for three construction projects intended to widen and improve segments of I-40 and associated interchanges in Knoxville, Tennessee. The projects are within the karst terrain of the Valley and Ridge Province. Subsurface conditions are characterized by an irregular rock surface coupled with differential weathering. Because of the projects? impact to local and interstate motorists, consideration was given to innovative planning, materials and construction practices that could accelerate construction. Two innovative deep foundation measures included rock-socketed pipe piles, which act as both foundations and substructure elements for a bridge?s interior bents, and the first widespread use of rock-socketed drilled shafts as bridge foundations on a TDOT project. The pipe piles were used at a site with significant cavities within the limestone bedrock. This resulted in design verification and constructability difficulties that required delays, but measures were ultimately employed to produce a sound foundation system. Over 110 drilled shafts have been constructed at sites with generally low solution activity. Relative to H-pile footings, which were included as an alternate foundation, they have apparently allowed accelerated construction at a competitive cost.

Jan 1, 2006

By Gary Kuhns

Central Florida is among the fastest growing urban areas in the United States, and its rapid development has required the steady construction of various types of civil engineering works. The karst geologic terrain and variable geotechnical conditions, however, present special challenges to the design and construction of deep foundations. The subsurface profile can be idealized as a surficial layer of Pleistocene sands, underlain by the highly variable Miocene-age Hawthorn Group, consisting of various combinations of sand, silt, clay, phosphate and highly weathered limestone. The Hawthorn Group is underlain by Eocene-age limestone that comprises the Floridan aquifer. Vast networks of solution cavities are present throughout the Eocene limestone, sometimes allowing downward raveling of the overlying soils and the creation of sinkholes. In some cases, the relic sinkholes can be filled with soft compressible organic soils extending to depths greater than 100 feet (30.5 m). Driven piles are frequently employed as a deep foundation alternative, although occasionally cast-in-place piles/shafts have also been used. Piles are often driven for bearing in the weathered limestone within the Hawthorn Group, but are sometimes installed as friction piles in the upper soil and intermediate geomaterials. Dynamic pile testing is routinely performed during pre-construction test pile programs, or during production for quality control and assurance purposes. This paper presents discussions on the design and construction aspects of deep foundations unique to Central Florida subsurface conditions and local practice. Foundation issues such as subsurface variability, soil setup, pile damage, negative skin friction, and sinkhole conditions are discussed with the aid of demonstrative case histories.

Jan 1, 2003