Search Documents

CrusherMapperTM - A New Tool for Crusher Condition Monitoring The efficiency of mineral processing plants is entirely dependent on the availability of the plant equipment critical path. This typically concerns comminution circuits consisting of primary crushers and primary grinding mills. Crusher and mill availability are determined by the frequency and duration of maintenance shutdowns, which are primarily driven by the need for replacement of sacrificial liners. The change of crusher and mill liner shape over respective life cycles also strongly affects plant efficiency. It is therefore highly desirable to accurately monitor the condition of mills and crushers in order to optimise plant efficiency through maximised availability and targeted liner shape. Traditional comminution liner and other production parameter condition monitoring has been attempted through ineffective methods which prevent satisfactory management of crusher and mill maintenance and reduce operational control. This situation has recently dramatically improved for grinding mills through the development and commercial deployment of MillMapperÖ, a technology based on three-dimensional laser scanning data and dedicated software (Franke, Lichti and Stewart, 2006; Franke and Lichti, 2007; 2008; Franke, 2008; Franke, Redman, Johnson and Michalek, 2009). At the time of writing in late 2009, MillMapperÖ is in successful use at a rate of approximately 170 surveys and associated reports per annum at processing plants in Australasia, South America, North America and Africa. This paper presents the introduction of CrusherMapperÖ, the MillMapperÖ equivalent for crushers. CrusherMapperÖ also utilises high density, high accuracy laser scanning data, and features dedicated algorithms for three-dimensional monitoring of wear on crusher concaves and mantles. This facilitates the detection of wear hot spots or zones or localised liner failures, and accurate forecasting of reline tonnages and dates. It also for the first time provides the means to establish optimised concave and mantle shapes in order to achieve production targets. In contrast to any other currently utilised condition monitoring method, CrusherMapperÖ data collection can occur remotely and does not require any shutdown or crusher isolation. This method therefore does not interrupt crusher production while at the same time eliminating any confined space risk normally associated with taking measurements inside the crusher cavity.

Sep 13, 2010

By A. M. McKim

6, 7.3 meter diameter autogenous mills at Wabush Mines are undergoing conversion from a radial configuration of pulp discharger to a curved design. Improved discharging efficiency has effectively lowered the pulp level in the mill. The low level operation enhances the grinding efficiency netting a 12% power reduction. Significant reductions to rate of wear has been a spin off benefit. The design incorporates features for holding the assembly solidly in place thus eliminating bolt hole damage and leakers. Preliminary work in one 11 meter mill at Hibbing Taconite did not indicate that all the same advantages were available in their process.

Jan 1, 1982

By John Gross

From the time when man first pounded one rock upon another or used heat and sudden chilling with water to disintegrate rock, the art of crushing advanced but slowly to the mule-driven arrastre and the Chilean mill stage until the advent of power-driven appliances made material progress possible. The combined efforts of manufacturers and operators have made modern machines highly efficient mechanically. Although marked progress has been made along mechanical lines, the theory and conception of underlying principles have not advanced so rapidly. This lack of advance in theory may be attributed to the unfortunate situation resulting from the controversy as to whether the Rittinger or the Kick law is applicable to crushing. Many pages of the technical literature are burdened with theoretical discussions in favor of one or the other of these laws, which have tended to cloud rather than to clear the atmosphere.

Jan 1, 1938

By J. J. DeMull, B. A. Boster

Amax's Sleeper mine uses conventional cyanidation milling and heap leaching techniques to produce gold. Since milling operations commenced in March 1986, average ore processing rates have improved from the design rate of 455 t/d (500 stpd) to more than 720 t/d (795 stpd). Heap leaching was added to the process facilities in September 1986 at a design rate of 1.5 kt/d (1650 stpd) and current heap leaching rates exceed 2.7 kt/d (2950 stpd). Presented are descriptions of the Sleeper processing facilities with emphasis on the crushing and grinding circuits, a review of the selection of crushing and grinding equipment, and a summary of operating performance during the first 16 months of operations.

Jan 1, 1990

By B. Fagerberg

Crushing and grinding practice in Sweden follows largely the international pattern. Certain special circumstances, however, have had an influence on the development. Most mines are worked underground in either quite small or in very large units. To utilize small sulphide ores, custom milling is rather common. Apart from the cement industry, the rock species treated are hard and abrasive. Another important factor is the increasingly strict requirements placed on the mechanical condition of different products, especially lump ores and coarse iron ore concentrates. A significant feature in the design and development of Swedish crushing and grinding practice has also been close cooperation between machinery manufacturers and the users. An account of these conditions and an outline of the crushing and grinding techniques employed in Sweden are presented in this paper with emphasis on the mining industry. For background purposes it may be mentioned that crude ore production in Sweden last year included 45 mill. tonsx) of iron ore, of which some 20 mill. tons from Kiruna alone, and 4 mill. tons of sulphide ore from 22 other mines, fig. 1. In addition 8 mill. tons of limestone were quarried for cement production and several million tons of stone and sand for roads, aerated concrete, etc.

Jan 1, 1968

By G. P. Holmes

"IntroductionThe copper-molybdenum property of Brenda Mines Ltd. is located 18 miles north west of Peachland in the Okanagan Valley of the Southern Central interior of British Columbia. The actual site is 50 miles north of the international boundary and 150 air miles east of Vancouver at an elevation of 5000 feet above sea level. The earliest written mention of the prospect is found in the Geological Survey of Canada, Memoir No. 243, issued in 1947 by Dr. H.M.A. Rice. In 1954 the area was staked by a prospector, Bob Bechtel, who interested Bern Brynelsen of Noranda Exploration in examining the claims. A joint Noranda - Kennecott program resulted but since the grades were so low the property was not taken up until in 1964 a re-examination by Chapman, Wood and Griswold produced recommendations leading to the construction of the Brenda Mine as it is today.The rounded, timber covered mountains of the area are composed of the tuffs, argillites and limestones of the Upper Triassic Nicola Group, which is intruded by a Jurassic quartz diorite, called the Brenda stock0 The actual orebody occurs in a strongly fractured zone within the Brenda stock, approximately 1500 feet from the contact with the Nicola group0 The ore minerals, .chalcopyrite and molybdenite, associated with pyrite and magnetite of lesser importance, occur as fillings within the fractures 0 The grade of the ore decreases outwards from a central higher grade core and in January 1971 total reserves were estimated at 165 million tons assaying 0,182% Copper and 0,049% Mo."

Jan 1, 1972

Shoemaker: We've all heard a lot about epoxy liner backings. This brings up the question-do zinc furnaces still have a place in a new plant? Meaders: I would, you must understand, be prejudiced in this question because we introduced epoxy backing into the industry. Naturally, we wouldn't have done so if we didn't think it should be done. With that background maybe I could give a little more information on this particular subject than some of the others, because we now have been in this business for some three or four years.

Jan 11, 1967

By John Gross

THE deductions drawn in crushing and grinding operations have heretofore been based on a separation of the products into various sizes. A crushed product may be sized by sieving, by elutriation, and by aid of the microscope. To estimate the surface of each size the relation of the surface to the estimated average diameter must be assumed. Such a relation, owing to the irregularity of the particles, may involve two assumptions: First, a factor to convert average diameter to surface for one particular size; and second, a variation in the factor as the diameter of the particle changes. Obviously a surface measurement in which such assumptions and estimates are involved is questionable. In the first paper of this series1 a method has been given by which an accurate measure of surface of quartz can be obtained from its dissolution rate. By the use of this method, surface measurements have been made on a series of sieve sizes of crushed quartz, the results of which are given and discussed in this paper.

Jan 1, 1928

By D. W. Zandee

"IntroductionHaving mined an economic mineral bearing rock which is of insufficient grade to warrant direct smelting, upgrading or beneficiation is required to make it an economically viable ore. The first step in effecting the concentration process is comminution or sequential breaking of the rock to allow liberation and subsequent recovery of the desired mineral particles. Desirably the ore could be broken down to the point where the valuable mineral is completely liberated to maximize the chance of recovering as much of it and in as pure a form as possible. The number of energy intensive stages of breakage required to attain this goal depends on many physical characteristics of the ore such as hardness, friability, toughness, grain size, existing fracture planes and particle shapes.Commonly the distinct stages are primary, secondary and often tertiary crushing and finally grinding. To increase the efficiency of each stage of size reduction, pre-treatment sizing is common.Crusher feed is commonly scalped of large pieces or screened for reduction crushers and classified for secondary grindingcircuits.Although crushing and screening is employed for many different products, this chapter reviews current practice in larger tonnage metalliferous ore treatment plants.Current practice is to use large gyratory or jaw crushers for primary crushing and some sort of gyrating or cone crushers for additional stages of reduction. For autogenous or semiautogenous grinding circuits only the primary crushing stage is necessary, the balance of the work being performed in the grinding stage. For conventional grinding circuits using ball mills or combinations of rod and ball mills, secondary, tertiary and even quaternary crushing stages are normally required.Older type crushers such as stamp mills, double rolls, sledging mills and hammermills are no longer common but are used for small tonnage special processes.Important to efficient crushing are a variety of sizing devices such as grizzlies and vibrating screens. Products at different stages must be stored to give surge capacity and allow controlled feeding rates through mechanical and gravity feeders. These storage piles, bins and feeders as well as crushers and screens are commonly integrated into a total facility by means of conveyor systems. Most often these are endless rubber belts driven by simple or multiple drive mechanisms usually consisting of electric motors and speed reducers."

Jan 1, 1989

Mine ore, reduced to minus 71/2 in. by primary crushers, is stockpiled. Size reduction of the reclaimed material by secondary and tertiary crushers is achieved in a closed circuit crushing and screening plant. Screen products of minus 30 mm plus 6 mm lump, and minus 6 mm fines are stockpiled by conveyor and stacker systems prior to rail despatch 10 port facilities at Dampier. Crusher settings, determined from experience, are closely maintained to obtain the desired lump/fines ratio. Chemical and sizing analyses from automatically taken samples are used to maintain product specifications. The beneficiation plant upgrades the fines product when this is necessary. The recorded wear life of individual plant components is the basis of a planned maintenance programme.

Jan 1, 1970

By S. D. Michaelson

Open pits and quarries are the major sources of all "hard rock" tonnage mined today. Normally, ore is fractured from the pit face by blasting and then truck-hauled to a primary crusher where processing begins; over- burden (or waste) is generally truck-hauled from the pit to dump areas. Truck haulage of blasted ore and overburden accounts for some 25 to 50 percent of total mining costs in a typical open pit and commonly is the largest single cost factor. Obviously then, cost reduction efforts should properly focus on improving existing haulage systems and developing new breakthrough techniques for material transport. Continuous flow systems for large tonnages ordinarily will result in a lower cost than batch systems such as truck or rail haulage. Continuous flow with pipelines for liquids and slurries, or conveyors for medium to coarse dry materials (in the -8 in. range) are the accepted economic answers for bulk materials handling over reasonable distances.

Jan 1, 1968

Crushing Plant Process Optimisation Design of processes in order to find the most efficient solution to a specific task is a difficult problem. Often the number of solutions are large and the optimal solution is therefore difficult to identify. Crushing plant process design is no exception from this statement. In order to find the best solution issues like equipment selection and process configuration must be mastered. The solution must both be technically feasible and preferably have a low operating cost. Since crushing plant design is a complex task with a large solution space it is basically impossible to master without a specialised tool. For a long time simulation softwares have been used to assist in the design process. These tools only give answers for how a user defined plant will operate. There are no tools with capabilities to consider different design options in order to determine what the most efficient solution looks like. In this paper a method for crushing plant design optimisation is presented. The novel method utilises a combined optimisation routine and expert system in order to find the most cost efficient solution to a given process task. The user will only need to define the feed material properties, the process capacity, and the end product requirements. The developed system will find the solution lowest production cost per ton.

Sep 13, 2010

By E. R. Johnson

THE copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the western flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past 15 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. FORMER PLANT The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7 1/2 gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by 1-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55 1/2-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73 1/2-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bin serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 1 3/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7 1/2 McCully gyratory crusher set at 1 3/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73 1/2 by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1947

By W. L. Dumoulin

A RATHER detailed description of the entire plant and leaching process was given in a paper recently presented to the Institute,1 so this paper will cover briefly only the crushing practice of the New Cornelia Copper Co. for the year, 1918. The ore, which is mined by steam shovels and loaded in side-dump cars, passes through two crushing plants. These crushing plants were constructed to crush the ore required by a leaching plant of 5000 tons daily, capacity, during a crushing period of 16 hours. The primary plant reduces to less than 3 in. (76 mm.) and the secondary plant, to ¼ in. (6.35 mm.), which is sufficiently fine for satisfactory percolation of solution through the ore in the leaching tanks, and to give good extraction. The ore is then conveyed to the leaching tanks by a system of 28-in.. (71-cm.) belt conveyors. On the way to the leaching tanks, it passes through an automatic sampling plant, where a 1-per cent. sample is taken. From the primary crushing plant, the ore is conveyed by two 36-in. (91-cm.) belt conveyors to a 10,000-ton steel storage bin, with a reinforced-concrete flat bottom. The ore discharges from the bottom of this bin onto four 20-in. belt conveyors, which deliver it to the four units of crushers in the secondary crushing plant. There is no storage bin between the mine and the primary crushing plant. The ore breaks very coarse, is very hard, and contains a great many boulders, some as large as 4 ½ by 4 1/2 by 10 ft. (1.3 by 1.3 by 3 m.). Jams form in the bowl of the coarse crusher in the primary crushing plant, as a consequence, and are freed by means of an immense steel hook operated from a 40-ton electric traveling crane.

Jan 8, 1919

By H. A. BURK

THE ores of the Tonopah, district are hard, compact and' highly siliceous. They contain from .1 to 2, per cent. of sulfide material, of which argentite is the valuable mineral; occasionally pyrargyrite is found in the richer ore. The sulfide is, chiefly pyrite with small amounts of chalcopyrite,. and sometimes sphalerite. The ore also contains a small amount of gold-about 1 per cent. by weight of the silver present. The major gangue constituent is quartz but frequently considerable rhodonite-called by the miners pink manganese-is present. For primary crushing, jaw and gyratory crushers are used. These crushers are of such capacity that, in most cases, one 8-hr. shift will supply the mill for 24 hr. The Extension Co., at the Victor ore house, passes the ore through a 13 by. 24-in. Blake type McFarland crusher set at 13 in., and at the No. 29 re house, a 14 by 24-in. Blake type Traylor crusher is used. The ore is thus crushed to stamping size in one reduction. The capacity of each crusher is about 40 tons per hr.; the power consumption is 0.6 kw. per ton.

Jan 1, 1921

By Rong Fan, Roger Smart, Ning Xu

As part of an Australian Research Council project with Newmont and Newcrest mining companies studying the influence of clay minerals on rheology, hydrodynamics and flotation response, the cryo-SEM technique has been used to capture and image the clay (low crystallinity kaolinite Q38) aggregate structures in the flotation pulp immediately after collector and before frother addition. Samples were also collected from the earliest froth phase and the froth overflow corresponding to early and later concentrates. In this technique, a copper tube is filled with the sample during operation of the cell. The tube is immediately plunged into liquid nitrogen vitrifying the water phase before it can crystallise as ice thereby retaining the structures without volume or other physical change. After sublimation of the vitrified water surface, the aggregate structures are revealed and can be compared between pulp and froth phases from clays in different feeds and flotation conditions. The images from both low-clay ore and ore with clay content reveal various levels of aggregation as predominantly edge-edge connected aggregates similar to those found in our previous studies of high-clay tailings. For the samples from the ore with clay content, more extensive edge-edge clay strings are found in the early froth phase as compared to exiting froth overflow and the pulp phase with short edge-edge connected strings. It is suggested that the strings of clay particles result from edge-edge aggregation in the Plateau borders of the bubbles before breakage during sampling and the more extensive edge-edge aggregation in early froth phase is induced by crowding in the bubble borders. The clay strings collected into the overflow concentrate are almost all broken up compared with the Froth before drop-back. The implications for entrainment and entrapment mechanisms of gangue capture in froth will be discussed.

Jan 1, 2014

By L. K. Eigenbrod

Throughout the mining industry, pneumoconiosis is one of the most severe occupational health problems being faced. The goal of completely eliminating pneumoconiosis as an occupational health hazard was underscored by the Federal Government with its enactment of Public Law 91-173 (Federal Coal Mine Health and Safety Act of 1969). Under this law, permissible dust level standards will be placed at 2 mg/m3 in mine atmospheres by December 30, 1972. The mining industry is thus faced with the tremendous technical challenge of achieving this level. Two basic questions can be raised with regard to this legislation. First, does a maximum dust concentration of 2 mg/m3 prevent the occurrence of pneumoconiosis? Secondly, can this dust standard be achieved using presently available methods and equipment? A precise answer to the first question has not yet been developed by the medical profession. Studies are continuing on the origin, prevention, and therapy of pneumoconiosis, and permissible dust levels could become even lower as medical evidence accumulates. The mining industry has addressed itself to the problems of dust con-tro1 for many years as related to personnel health, explosive mixtures, visibility, and machinery damage. Dust control methods being employed involve

Jan 1, 1971

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F) (MSHA 2008 [1]). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by > 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures (Bissert et al. 2017 [2]). In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F) (MSHA 2008 [1]). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by > 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures (Bissert et al. 2017 [2]). In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy

By L. Yan, N. Damiano, J. Bickson, E. Bauer, D. Yantek, B. Whisner, M. Reyes, J. Srednicki

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35°C (95°F) [1]. The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by >5.6°C (10°F) in mines with elevated mine strata and air temperatures. In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35°C (95°F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy. INTRODUCTION The apparent temperature inside an occupied RA could be significantly affected by the surrounding environment’s thermal conditions, such as mine air temperature and mine strata temperature. Apparent temperature (AT) is a temperature-humidity metric for the perceived temperature caused by the combined effects of air temperature, relative humidity (RH), and air velocity. It is used to assess the perception of indoor temperatures. Depending on factors such as geographic location and season, mine air temperature, relative humidity, and mine strata, temperatures can vary significantly [2]. RAs located in cold mines may pass the 96-hour 35°C (95°F) AT limit test that poses a challenge for RAs located in hot mines. One solution in these cases is that the occupancy of the RA could be derated (i.e., the RA occupancy could be reduced) to ensure the AT limit is not reached. However, this would require mines to purchase additional RAs to accommodate all personnel in the mine. For mines with high temperatures (above 26.7°C or 80°F), the occupancy might have to be reduced so much that the necessary number of additional RAs would be impractical. In these cases, RA cooling systems could provide a solution.

Jan 1, 2019