Search Documents

By Tchingis Lekhatinov, Lev Filippov, Vyacheslav Severov, Alexandre Matinin, Victor Samyguin, Inna Filippova

"Comparison of flotation efficiency of the new multi-zone flotation cell (MZFC) and different conventional cells was carried out at lab and pilot scales on the various samples: high contrast pyrite tailings and old copper containing tailings. MZFC is a cell of intensive flotation, which provides optimal hydrodynamic conditions for all flotation sub processes. Enhancing of particle attachment, creation of conditions for coalescent flotation, selection of spatially separated zones according to optimal hydrodynamic conditions for flotation sub-processes are proposed as main principles to design an MZFC. The bubbles/pulp stratification was pointed out as a limiting step in the existing intensive flotation machines. Two strategies to improve bubbles/pulp stratification in the MZFC were studied: (a) impact of pulp-bubble jet to the surface of a prismatic insert inside of cell, which provides the detachment of low hydrophobic particles from bubbles, and (b) profiling the pulp/bubbles jet from the reactors due to a specific geometry of cell walls. The new continuous MZFC devices were demonstrated similar or higher efficiency in comparison with laboratory batch flotation cells for pyrite flotation. Higher flotation efficiency (82%) with pure pyrite concentrate (51.2% of sulfur) and a recovery level of 92% was obtained in MZFC when the cell with stratification by impact was used. Similar results were obtained with old Cu-containing tailings. Although MZFC had 1.5 times greater yields of concentrate than a batch flotation cell, it provided the increase of chalcopyrite recovery by 29.4% and concentrate grade by 4.8%. An original organization of pulp/bubbles stratification in the separator part of the new intensive flotation machine using variable geometry inserts allowed the best flotation selectivity with a bubble mineral loading coefficient 1.5 fold higher than the laboratory mechanical or pilot cells."

Jan 1, 2014

By H. Cevizci

"Numerical simulation of the plaster stemming method (PSM) was performed and compared with the conventional drill cuttings stemming method (DCSM). Many earlier in situ tests have proved that PSM can use the blast energy more efficiently than DCSM. Despite PSM generating more blast vibrations, it has advantages over DCSM such as better fragmentation and lower cost per unit volume of rock blasted. In this study, numerical simulation with Autodyn software using a 2D tool was employed to prove the efficiency of plaster stemming by comparing parameters such as pressure, Y-velocity, Y-force, internal energy, acceleration-Y, and compression. For example, the maximum pressure attained at the top of explosive column was 7 395 MPa for DCSM whereas it was as high as 11 945 MPa for PSM. Most of the computed parameters were significantly higher in PSM than those obtained for DCSM. This paper is the first study elucidating the efficiency of PSM by numerical simulation. It is concluded that PSM can save substantial amounts of money and effort. IntroductionThe stemming of blast-hole collars in surface mines with an inert material redirects blasting energy to the rock more efficiently, thus the blast-induced energy is utilized more effectively in breaking rock. With proper stemming, the gases should not escape due to loose stemming material. More efficient stemming with better confinement therefore increases the blast fragmentation. In addition, the distance of scatter is increased, giving rise to a looser rock pile that can be more easily loaded and transported. In order to improve the performance of a blast, stemming is used to help maintain the gas pressure over time (Konya and Konya, 2018). Proper stemming has been shown to increase the explosive efficiency by over 41% (Snelling and Hall, 1912).The most common stemming material in open pits and quarries is drill cuttings because of their ready availability at blast sites and the drill cuttings stemming method (DCSM) is a low-cost method. However, it has a major disadvantage in that dry drill cuttings eject very easily from blast-holes during an explosion, thus a great percentage of the blast energy is wasted and lost to the atmosphere. Cevizci (2012, 2014, 2013, 2017) studied blasting parameters in open pits and obtained better results with the plaster stemming method (PSM) in many limestone, basalt, and clay quarries. Moulding plaster is preferred for stemming because of the fast hardening time of 25–30 minutes."

May 1, 2019

By F. M. Lyon, F. J. Chernosky

Research efforts have not developed techniques for the complete desulfurization of coal that is needed to reduce air pollution caused by burning coal and to reduce the sulfur in metallurgical coke. Sulfur in coal occurs in three forms and of these, the pyritic sulfur occurs as discrete mineral particles and, at least theoretically, should be subject to physical rejection. Pyrite occurring in hard rock mining is concentrated by froth flotation; therefore, the possibility of removal of pyrite from coal by flotation does exist. With this possibility in mind, the flotation and adsorption characteristics of ore and coal-pyrite were compared while using potassium ethyl xanthate as the collector.

Jan 1, 1973

By L. Gutierrez, R. Yepsen, F. Alarcón

Chile is the world's largest copper producer which is mostly in the form of sulfides for which froth flotation is the most efficient concentration process. As a result a concentrate that contains high concentrations of copper sulfides such as chalcopyrite, chalcocite and enargite is obtained. In the last decades processing of ores containing high concentrations of enargite (Cu3AsS4) has continuously increased in Chile, which is related to the fact that ore deposits nawadays are more heterogeneous and complex. Enargite is a mineral that contains arsenic and its presence in the copper concentrates implies severe penalties. In addition, the shortage of fresh water has driven the search for new alternative sources of water, among which seawater has proved to be one of the most attractive. The objective of this research is to study the behavior of the enargite in the process of flotation using seawater, and at the same time to compare its behavior with the results obtained using conventional water. The study was carried thorugh micro-flotation tests using pure samples of enargite, at pH values ranging from 4 to 11, both in fresh and seawater. PAX and MIBC were used as collector and frother respectively. Micro-flotation tests were also done at different redox potential conditions so that the effect of the surface oxidation of enargite was evaluated in seawater. The results indicate that the recovery of copper from enargite is reduced in seawater compared to fresh water, in particular at the pH values close to those of the formation of the first hydroxy complexes of Mg and Ca. In general, the experimental data indicate that the floatability of enargite is strongly affected when seawater is used, in particular at oxidizing conditions. These results suggest that Mg2+ and Ca2+ ions contained in seawater interact with the surface of enargite forming hydrophilic species.

Jan 1, 2018

By W. U. Reimold, R. Armstrong, R. G. Charlesworth

For many years rockbursts have plagued the mining industry. Although much research has gone into studying this phenomenon only a small proportion of it has been on the actual source mechanism. A study was recently carried out to compliment the previous work done on the micro-structure of these features and to compare it to the micro-structures seen on shatter cones, from meteorite impacts. Both optical and electron-microscopy were used during the study. Samples were collected from rockburst sites by the CSIR Miningtek Rockburst Investigation Unit, and from the collar of the Vredefort Impact Crater. In the optical-microscopy study, the pinnate fractures observed in previous studies were seen in the shatter cones, through all the material. In the rockburst samples, the fractures were observed only in the quartz grains. Quartz micro-crystals were present in the rockburst samples and appeared to be the product of comminution rather than crystallisation. Cataclasite was present on rockburst and shatter cone fracture surfaces. The observations of the shatter cone surfaces with the scanning electron microscope are in agreement with previous work, including the observed presence of melt features, spherules and spheroidal material. The deformation in the rockburst samples is concentrated in the quartz grains, highly complicated with brittle features like sub-conchoidal structures and step structures present. A quartz spherule was identified on one rockburst sample and rhombic-dodecahedra type micro-crystals were present and seen fracturing off quartz grains. It is clear that the rockburst and shatter cone fracture surfaces are quite different; the shatter cone deformation is equally distributed across the sample and involves plastic-deformation, while the deformation in the rockburst material is concentrated in the quartz grains and, with the exception of spherule formation, is brittle. This study agreed with the current explanation for the formation of the rhombic-dodecahedra, and disproved the possibility of it being coesite or fine-grained meta-chert. Although there is no definite evidence of the mechanism of formation of the spherule, it is believed to be the product of vaporization and condensation, and the presence of this material indicates the extreme conditions under which this event occurred.

Jan 1, 2003

By Vincent Scovazzo

This paper compares the two most common pillar design equations used worldwide by John T. Boyd Company; the Mark-Bieniawski Equation, an empirical approach, and the Wilson Equation, an analytical approach. The equations are compared in two ways; by their stress profiles and by the Mark-Bieniawski Equation stability factor. Contrasting the two equations based on the visual comparison of their stress profiles is straight forward but evaluating their resulting pillar designs is problematic. Complications arise due to the differences between the use and development of stability factors for empirical equations and safety factors for analytical equations. To work around these differences, comparisons are made between the two equations by first calculating pillar sizes using the Wilson Equation and then determining the Mark-Bieniawski Equation stability factor for these pillars. Pillars designed using the Wilson Equation were based on site-specific data from 23 mines located in the Americas and Australia. Comparing sizes of pillars designed by the Wilson Equation to the Mark-Bieniawski Equation; the Wilson Equation pillar sizes were smaller in 77% of the cases, similar in 3%, and larger in 20% of the cases.

Jan 1, 2008

By Kim Le Roux

Cemented paste backfill (CPB) is a relatively new material that is increasingly being used in open stope mining across the world. The advantages offered by this high density tailings backfill include: a lower total cost associated with backfill placement, reduction of excess water underground; and the elimination of the need to process the tailings prior to placement. However, almost all backfill design is based on the performance of laboratory prepared samples since it is difficult to obtain undisturbed samples and conduct in situ testing due to the lack of access to backfilled stopes and the safety concerns in accessible areas. The logistical problems associated with conducting in situ testing and obtaining undisturbed samples of cemented paste backfill (CPB) has lead to the reliance in the mining industry on performance data obtained from laboratory prepared CPB samples. The degree to which these laboratory prepared samples represent the actual in situ condition is not well defined, partly because the influence of the mixing, transport and placement process on the material properties it is not well understood. Therefore, there is a need in the industry to understand how the material properties and hence the performance of the laboratory prepared CPB compares with in situ material. This paper reports the findings of an investigation into the in situ properties of CPB at a gold mine in Northern Ontario. A combination of in situ and laboratory testing, conducted on undisturbed samples, was used to quantify the in situ properties and performance of the CPB. These results were then compared to those of a laboratory based investigation of the same CPB. It is evident from this investigation that the bulk properties of the in situ CPB are different from those of the laboratory prepared CPB. The most significant observed differences are that the in situ CPB has a higher void ratio and a lower degree of saturation than the laboratory prepared material. The implication of these differences on the stability and performance of the CPB will also be explored in this paper. 1

May 1, 2002

By E. Vilaescusa, J. Eloranta

The work presented in this paper investigates the influence of non-ideal detonation characteristics related to the blasthole diameter, base emulsion sensitivity (micro-balloon sensitised versus unsensitised) and percent emulsion on the explosive shock energy available to break rock using ANFOemulsion blends. A series of theoretical equal powder factor bench blasting patterns with hole diameters of 127mm (5”), 140mm (5.5”), 152mm (6”) and 165mm (6.5”) are compared to assess the non-ideal confined shock-state work energies. The Non-Ideal Shock Energy Factor (NSEF), which is the available shock energy per cubic meter of blasted material (MJ/m3) or kilocalories per cubic yard (kcal/yd3), is used to compare the different blasting patterns charged with a range of ANFO-emulsion blends from zero to 50% emulsion.

Jan 1, 2012

By B. M. Kunar, C. S. N. Murthy, B. Rao K

Rock particle size has a very important significance in the mining industry, starting from blasting till the mineral processing. The present study was carried out to understand the particle size distribution in various sieves after conducting the ball milling process. The time of the grinding process was varied at different intervals. It was observed that 80% of the particles of both granite and marble rock samples passed through the 4800 μm sieve when subjected to grinding time of 40 minutes. Also, it was observed the number of particles that were retained in the smallest sieve of <75 μm was higher in the case of granite sample when compared to a marble sample. INTRODUCTION India is a major exporter of granite and marble stones. The major use of marbles and granites are constructing walls and floors. There are several machining processes that are applied before it is used as floors and walls. During this process, wastes are produced these wastes are used in various ways. These include use of powders for clay products (Segadães, Carvalho, & Acchar, 2005), as an additive in cement production (Aruntaş, Gürü, Dayi, & Tekin, 2010), to enhance the properties of brick ceramics (Saboya, Xavier, & Alexandre, 2007), in constructing bricks (Bilgin et al., 2012) and as an additive in concretes (Aliabdo, Abd Elmoaty, & Auda, 2014). Usually, the powder form of marble and granites are used as an additive in the above-mentioned applications. Powders of marble and granite are obtained through the grinding process. One such process of grinding is the ball milling process. In the ball milling process, a quantity of samples along with the charge quantity consisting of steel ball is subjected to a grinding process within a closed chamber as shown in Fig. 1. An even particle size can be obtained through sieving the material after subjecting it to grinding. The present study is planned to understand the particle size distribution in various sieves due to varying time and charge quantity in the experiment. Only time was varied to understand the amount of particle distribution in the case of granite and marble rock samples and a comparison is drawn. A statistical model was developed for marble rock specimen considering the data obtained by varying time and charge quantity in the ball mill experiment.

Jan 1, 2019

By Anil K. Ray

This paper discusses in situ studies conducted at an Illinois Basin room-and-pillar coal mine to evaluate the performances of three different types of bolts under similar geologic conditions. The bolt types considered were the fully grouted passive rebar (FGPR), the resin-assisted mechanical anchor (RMAB), and the fully grouted tension rebar (FGTR). During the evaluations, the three types of bolts were installed in a single entry covering a span of three contiguous pillars with almost identical geologic conditions. The performances of the three types of bolts were investigated by instrumentting the bolts prior to installation as primary supports on cycle. Additional data on roof behavior was collected with extensometers and shear meters placed near the instrumented bolts. Excluding some time lapse right after installation, the performance evaluation of the three bolt systems was based on the data collected for over a year. Based on this study, it was found that the axial loads measured in the different bolt types did not show any identifiable patterns under the prevailing geological conditions at the mine. Therefore, the assumption that active bolts must be superior to passive ones is not always valid. Even though the studied mine did not have any thinly laminated, weak rocks in the immediate roof, the passive bolts performed as well as the active systems.

Jan 1, 2012

By B. R. Benner

Progressive improvements in crusher design, screening efficiency, and operating experience along with the downsizing of many taconite operations has resulted in the abilitv of some crushing plants to produce a substantially finer product. This finer product opens the possibility of replacing the rods in the rod mill with balls as is the current practice at Sydvaranger, Norway. If this replacement could be accomplished substantial savings associated with metal wear and the elimination of rod charging may be realized. The purpose of this study was to compare the performance of a mill charged with rods with the performance of the same mill charged with balls at the pilot scale. The first objective was to establish whether we could achieve the same throughput rate at the same mesh-of-grind in a mill in which the rod media has been replaced by balls. The second point was to determine whether the ball media would create a significant tramp oversize problem.

Jan 1, 1990

By Mark D. Hannington

Drilling of the active Trans-Atlantic Geotraverse (TAG) deposit during ODP Leg 158 indicated that the size of the mound-stockwork complex is approximately 3.9 million tonnes, including 2.7 million tonnes of massive and semi-massive sulfide (ca. 2% Cu) at the seafloor and 1.2 million tonnes of mineralized breccias (ca. 1% Cu) in a subseafloor stockwork. Quartz-pyrite veining in the stockwork zone extends from about 40 meters below seafloor (mbsf) to a depth of 95 mbsf. Siliceous wallrock breccias in the lower part of the stockwork grade abruptly into chloritized basalt breccias at the margins of the mineralized zone, and massive sulfides at the flanks of the deposit onlap relatively unaltered, partially hematized basalts. The pipe-like dimensions of the stockwork zone do not exceed the diameter of the sulfide mound. Comparisons with samples collected during earlier dive series confirm that the vent complexes at the surface of the mound are not representative of the bulk composition of the deposit. Dramatic vertical zonation of metals within the mound suggests that a long history of hydrothermal reworking has effectively stripped the constituents that are soluble at lower temperatures from the massive sulfides and concentrated them at the top of the deposit through a process of zone refining.

Jan 1, 1998

By T. M. Barczak

Stoppings are required to resist lateral forces on the face of the structure to control pressure differentials created by ventilating air. The design criteria in other parts of the world, including Australia, exceed this requirement by specifying over pressurization control to as much as 14 kPa (2 psi) in the active sections and 35 kPa (5 psi) in the main ventilating control areas. This is done to provide protection to the mine workers from explosive or air blast events within the mine that can create this over pressurization. The National Institute for Occupational Safety and Health (NIOSH) has been conducting research to develop a new testing protocol for rating mine ventilation stoppings. The premise of this work is that arch-loading conditions more accurately reflects the transverse load capabilities of stoppings in underground coal mines than the freestanding flexural strength test specified in the current Code of Federal Regulations (CFR). This work clearly shows that the transverse load capabilities of dry-stacked, mine ventilation stoppings are dependent upon the material strength of the block and the height and thickness of the wall, none of which are part of the current CFR criteria based on ASTM E-72 specifications. This paper compares the transverse load capabilities of several block materials and wall dimensions commonly used in stopping constructions based upon simulated three-hinge, rigid-arch loading tests of half-wall constructions in the NIOSH Mine Roof Simulator. The results indicate a wide-range of transverse load capacities, ranging from as low as 21 kPa (0.3 psi) to as much as 117 kPa (17 psi) for the conditions evaluated in this study. The current CFR criteria do not distinguish between applications of these stopping designs despite their wide variance in transverse load capabilities, which is not conducive to employing ventilation control strategies that isolate certain sections of the mine to prevent injury to mine workers.

Jan 1, 2009

By N Yarahmadi

Characterization of pore pressure is critical for appropriate design of tailings dams. Furthermore, if seepage rates through tailing embankments increase unexpectedly or become uncontrolled, undesirable conditions may prevail to progress piping or internal erosion that could lead to the dam’s instability or ultimate failure. A three-dimensional seepage analysis was performed on a tailings dam using finite element method to find the rate of seepage and pore water conditions in the embankment and foundation. The results were then compared to a conventional two-dimensional seepage analysis carried out on the typical cross section of the embankment and the field data acquired from the instrumentation system. Considering the monitoring data, comparison of seepage analyses results for the two and threedimensional models, showed that the results of the conventional two-dimensional seepage analysis are significantly underestimating reality. Relying on two-dimensional seepage analyses might result in underestimation of seepage rates and impact the safe operation of tailings dams. Similarly, unrealistic prediction of pore water pressure conditions, based on simplified seepage analyses, can lead to overestimation of the rate of strength gain of material and consequently safe embankment raising rates.

Jul 1, 2021

By Wael Abdellah

Mine haulage drifts are the primary access to the mining blocks of an orebody in a multilevel mining system of a tabular ore deposit. The stability and functionality of haulage drifts are thus crucial to the success of a mining operation. Drift instability could lead to serious consequences such as injuries, production delays and higher operational cost. In this paper, the performance of the haulage drift stability is evaluated on the basis of the primary rock support system comprising 1.8 m resin grouted rebars in the drift walls and 2.1 m long bolt in the back. Two failure criteria namely the extent of Mohr-Coulomb yield zones around the drift, and linear elastic brittle shear failure are adopted and compared, with respect to lower level and same-level mining and filling sequence in the vicinity of the haulage drift. The case study is one of the #1 Shear East zone of the Garson Mine in Sudbury, Ontario. Random Monte Carlo (RMC) technique, which has been previously established to assess the haulage drift stability, is employed in this investigation. The RMC technique is used in conjunction with finite difference modelling software FLAC for random assignment of model input parameters in the FLAC grid. Deterministic model results reveal the drift behaviour in terms of deformation (convergence) and mining-induced stress distribution. Comparison between the two different criteria is carried out to determine which method is most suitable in evaluating unsatisfactory drift performance. The results are presented in terms of probability of instability and categorized with respect to failure condition and mining step. It is shown that the brittle shear failure condition based on linear elastic response calls for enhanced support system at a later mining step than what Mohr- Coulomb yielding condition does. The paper presents a detailed discussion of the stochastic analysis results.

Jun 1, 2012

By A. Y. Senchenko, Y. V. Kulikov

"The most common technique for selection of grinding equipment is the Bond method implying determination of a ball mill work index (BWi). The method is perfect for greenfield projects where a ball mill must be sized to grind an ore to 80% passing 75-100 µm. Finer grinding will require application of specific correction factors to a standard equation since initially the method was not designated for sizing of fine (minus 75 µm) grinding mills. Significant issues are related to selection of grinding equipment for treatment of originally fine materials when the standard procedure is not applicable. In 1984, Levin published his special technique titled as “A proposed test for the determination of the grindability of fine materials”, where he offered to use the standard Bond ball mill for determination of a specific grinding energy. However, this method did not meet with wide recognition. In 2017, Institute TOMS under guidance of JKMRC’s specialists performed a testwork aimed at verification of a new universal technique for determination of grindability of initially fine materials. An object was to test three aged tailings samples for the subsequent modelling of comminution circuit and evaluation of potential throughput of the existing ball mills with final grind size of ?80 passing 53 µm. In parallel with development of the universal approach, TOMS’ specialists carried out tests according to the Levin method in order to compare the data resulted from two methods. The results from lab ball mill testing on three products following the alternative test methods are presented in this paper along with the testing methodology and results analysis. Specific energy was calculated for regrinding of the materials to the required size. Difference of the examined methods and assessment of their applicability for sizing of full-scale equipment are explored."

Jan 1, 2018

By I. Druce, C. Li, T. Qu, J. Dong, W. Y. Xinchao, V. Nkuna

CITIC Heavy Industries has a large installed base of grinding equipment throughout Africa in different configurations, including high-pressure grinding rollers with ball mill and semi-autogenous ball crusher. The total installed power of CITIC’s mills exceeds 430 MW. In this paper, we compare several typical grinding circuits of copper in Africa with about 15 kt/d throughput based on ore properties, process selection, equipment sizing, and key equipment capital and operating costs. Actual operating performance is also introduced. The comparison for the following mine sites provides a general reference for the selection of copper grinding circuits with this approximate throughput: Kamoa-Kakula Copper Mine with high-pressure grinding rollers with ball mill circuit, and Deziwa and Sicomine Copper-Cobalt Mines with semi-autogenous ball crusher circuits

Jan 1, 2023

By W. G. Pariseau

"BACKGROUND Strata mechanics of three underground coal mines in central Utah were recently studied using a specialized finite element technique [1, 2, 3, 4]. The purpose of these studies was to examine relationships between mining and related seismicity. The longwall mining method was predominant, but room and pillar mining and barrier pillar mining were also used in the mines studied. In every case, high correlation between face advance and seismicity was observed. The specialized finite element technique allows for whole mine subsidence estimation at a kilometer scale and for stress concentration at a meter scale near a working face. Comparisons of observed mine subsidence with model subsidence allows for model verification and justifies detailed analysis of the evolution of stress at seam level. Yielding is expected near a longwall panel face and as the face is advanced the extent of yielding is expected to increase. The total number of element failures in a finite element mine model also increases, so a high correlation with associated seismicity, say, event count, is not so surprising. A brief review of recent coal mine studies in Utah is presented in the sequel. The procedures are given in some detail in application to trona mining. COAL MINES The analysis procedure begins with the geologic column and proceeds to specification of strata properties including elastic moduli and strengths. Joints are an integral part of the geologic model and joint set specifications include dip direction, dip, spacing, stiffness and strength. Spatial variability of strata properties in situ may be taken into account during analysis. Topography is important, especially to Utah coal mines that are developed from outcrop in regions of high relief. Mesh generation follows specification of data input. Finite element analysis is next, followed by reporting of results. In this regard, all finite element computations are based on first principles. No model “calibration” is done that involves adjusting computer input to obtain a fit to mine measurements such as subsidence profiles. Figure 1 illustrates the concept of a dual node – dual mesh finite element concept. Dual nodes are roof and floor nodes in mined areas. These nodes replace the seam. The dual mesh is a much refined mesh with displacement boundary conditions obtained from the big mesh and thus replaces the effect of mining in the region outside the dual mesh. The refined dual mesh allows for details of stress, strain and displacement near a working face of interest. Strata Properties Strata properties include elastic moduli and strengths of intact rock between joints and joint stiffness and strength for each joint set present. Both properties sets may be obtained from laboratory test data, although testing joints poses a sampling problem in the field. The statistical variability observed in laboratory test data, say, in unconfined compressive strength tests is often characterized by much variation. In fact, the coefficient of variation, ratio of standard deviation to mean, is often greater than 35 percent. When sample values are mapped back to the mine location, one may observe spatial variability as properties vary from place to place as shown in Figure 2. Spatial variability may be incorporated into a finite element analysis with probabilistic assignment of properties to elements in accordance with measured variability. The result is a more realistic model of rock in situ."

Jan 1, 2017

By Deon van Tonder, Chuck Edwards

"Solvent extraction is used in many acid leach uranium circuits to upgrade and purify the uranium bearing solution prior to final product precipitation. A number of strip options are available to recover the uranium from the loaded organic. This paper compares some of these options on the basis of typical capital and operating costs for both the solvent extraction circuit and downstream uranium processing, and also considers other related issues. The aim is to provide an objective comparative assessment of these options that could be used as a qualitative guide in process selection or improvement.INTRODUCTIONIn the 1950s the uranium industry was the first industry to adopt solvent extraction (SX). Since then, the flow sheets have advanced. Notable was the introduction of tertiary amine extractants by General Mills during the late 1950s and 1960s (Mackenzie, 1997; Mackenzie, 2005), which is still today considered ‘state of the art’ technology. Initially solvent extraction was done in combination with ion-exchange, such as in the Eluex flow sheet, followed later by the adoption of direct solvent extraction from pregnant leach solution (PLS). From a strip-precipitation perspective ammonia strip followed by ammonium diuranate precipitation was widely adopted as the norm in the uranium industry. More recently alternative strip systems have been receiving increasing attention due to the environmental, health and safety issues associated with ammonia and the resulting calcined uranium oxide product. This paper explores some of these alternative options in comparison with the ammonia route.It is important to acknowledge that each operation is unique, and therefore the information and philosophy outlined in this paper serve to provide a general guide that can be potentially applied and adapted to any site or project."

Jan 1, 2013

By D. Van Tonder, C. Edwards

ABSTRACT Solvent extraction is used in many acid leach uranium circuits to upgrade and purify the uranium-bearing solution prior to final product precipitation. A number of strip options are available to recover the uranium from the loaded organic. This paper compares seven of these options on the basis of typical capital and operating costs for the solvent extraction circuit and downstream uranium processing and also considers other related issues. The aim is to provide an objective comparative assessment of these options that could be used as a qualitative guide in process selection or improvement.

Jan 1, 2013