Search Documents

By D. Malhotra

The economic viability of a mining operation depends on continuous process improvements. Diagnostic testing and plant auditing are essential useful tools to improve performance and reduce operating costs. Case studies are discussed to illustrate benefits of these techniques to improve plant efficiency.

Jan 1, 2001

By Harrison AT, Smart RM

Backfill systems using unconventional cementitious hinders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: 1. A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings 'stable' slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 in high and the tailings were relatively high in pyrite. .\ GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shnnkage). The system used a slurry, but the addition of the ;iutivator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: ò sloping widths (mining heights) above 1.6 in; and ò shaft pillar removals in seismically active areas at the end of the life of the shafts. \This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems).

Jan 1, 1998

By Scott King, Norm Patterson, Ruilin Yang

The multiple blasthole fragmentation (MBF) model developed by Orica models the contributions from multiple blastholes to fragmentation at any given point in the rock and simulates a production blast with the actual geometry of the blasted overburden and free faces, explosive loading, multiple decking, and delay timing of each explosive charge. The model has been successfully applied to several open pit mines and quarries around the world, including Canada and the United States. The peak particle velocity (PPV) induced in the rock from the explosive detonation is used in the MBF model as the key parameter relating to the size distribution of the rock fragmentation. Relating the PPV to the rock fragmentation is based on earlier work relating the particle velocity to the dynamic strain in rock. A recent publication further revealed that the PPV is related to the maximum relative displacement that induces three dimensional strain at a point in the rock. The model can explicitly model most of the blast design parameters including explosive properties.

Jan 1, 2018

By G. Naud, J. Robitaille, M. Buonvino, A. Veltmeyer, A. R. Laplante

"A B6 Falcon concentrator was tested on several systems: a synthetic magnetite-silica ore, a massive sulphide gold-copper ore, a fine gold-pyrite-silica flotation tail, and a high grade gold ore in a low sulphide gangue (cyclone overflow).The Falcon demonstrated its ability to achieve separation in all cases, but with varying degrees of success. For the magnetite-silica system, separation proceeds until the concentrate bed overloads, at a mass of 300 to 400 g of magnetite. Recovery increased with decreasing particle size, down to the 25-37 µm and in some cases even the -25 µm class. Bowl geometry (angle) and gangue size distribution were the most significant operating variables. Results with the massive sulphide ore were the poorest, with gold recoveries typically around 10 to 20% at very low upgrading ratios, 1: 1 to 5: I. Gold recovery from the fine flotation tail ranged from 30 to 70% at upgrading ratios of 5 to 15; actual plant application would require a continuous unit (Falcon C20). The high grade gold cyclone overflow yielded a wide range of gold recoveries, but a very consistent relationship between recovery and mass processed. A concentrate of 0.5% Au could be processed at a recovery of 50%.The paper also presents results of a C20 application to recover fine iron from a magnetic tail. The unit is capable of recovering approximately 70% of the fine liberated iron in a high density product, with modest upgrading below 105 µm, and virtually complete rejection of the + 300 µ m product."

Jan 1, 1993

By Dr. O’Neil Thomas J., Donald W. Gentry

There are mines that make us happy, There are mines that make us blue, There are mines that steal away the tear-drops As the sunbeams steal away the dew. There are mines that have lost the ore chute faulted, When the ore's forever lost to view, But the mines that fill my heart with sunshine, Are the mines that I sold to you. -Anonymous INTRODUCTION The preceding chapters have discussed, in various degrees of detail, the primary considerations necessary to perform a cash flow analysis of a mining-related investment opportunity. Although the previous discussions regarding the manipulations, calculations, and interrelationships of the various components of the pro forma income statement were illustrated in the text, many individuals are un- familiar with the format and appearance of a final spread sheet for the evaluation of a mining property. As a result, it seems appropriate to conclude this book with an abbreviated case study of an actual mine property (currently in production) showing the cash flow analysis and some back-up data. Obviously all of the supporting data and calculations for the case study presented cannot be provided; however, reference is made to the major assumptions utilized and to the appropriate procedures employed in the calculations, as described elsewhere in the text. The problem associated with using any case study for illustrative purposes is that one tends to be overwhelmed by detail. For instance, specific costs, prices, expenditure timings, and other variable values may be challenged because they either do not conform to one's expectations or are not consistent with specific operating experiences. When this occurs the instructional value of the problem becomes obscured. The purpose of most case studies, and particularly the one presented in this chapter, is to expose the student to the methodology, procedure, and format associated with performing a cash flow analysis of a mining property. It is not to laboriously wade through the specific details associated with operating and capital cost development, mine plans, or equipment schedules. It should be noted, how- ever, that the values represented in this case study result from specific mine plans, operating procedures, equipment spreads, manpower requirements, and other en-

Jan 1, 1984

This article presents a proposal for the rehabilitation of the mined area of the Mogiana quarry. The Mogiana quarry produces material used in civil construction and is situated in the Brazilian State of Spo Paulo in the kilometre six of the Mogf Mirim - Itapira highway. The mineral exploitation in the Mogiana quarry provokes modifications in the environment such as alterations in the relief, vegetation, quality of the air, water and landscape. Through previous study of the area it was verified that after the closure of the exploitation the mine should be occupied mainly by pasturage. At the closing of the mine the exploitation benches, berms and slopes in general as well as the surrounding areas should be covered with a layer of soil and vegetated with native species in order to mitigate the negative impacts caused by the mine. The rehabilitation project of the area is based on the probable future use of the area, located between agricultural cultivations and cattle creation. The great alteration of the relief and soil would make future use of the area for agriculture difficult. It is more suitable t0 animal creation, mainly cattle. The high and thick rock slopes originated by the mining should be covered by vegetation, where possible, to reduce the negative visual impact. Obviously several measures will be necessary to reduce the impacts on the environment during mining. The final and definitive reclamation will only be possible after abandonment of the area. The main aspects of this reclamation process will be discussed in this paper.

Dec 6, 2010

Central to any business is its Asset Management Plan which encapsulates the business context and key organisational objectives such as profitability, safety and environmental standards. Life Cycle Planning (LCP) is a key component of an overall Asset Management Plan. A comprehensive approach to Life Cycle Planning forecasts the financial expenditure required to support the performance of the asset over the business life. It incorporates capital, maintenance and operational expenditure along with an estimation of economic life. Within its body the LCP provides the detail of the maintenance plan and method of its execution. Once optimised the LCP becomes the overarching plan executed through the application of several elements of the Asset Management Plan to ensure the return on investment from the assets is optimal. Each of the elements of the LCP is bound by a set of loops that provide information based on the analysis of outcomes. These loops drive the continuous improvement of performance and cost over the life of the asset. In this way we ensure that the LCP is a dynamic plan responsive to the changing business environment. The paper being presented today will describe the process undertaken and the outcomes derived when this approach was applied to a $600 M+ coal handling and preparation plant in QueenslandÆs Bowen Basin. It will also delve into the difficulties encountered from both technical and cultural aspects; the latter proving to be the most difficult to manage. It will describe the hurdles and barriers that hampered progress including the human influences and the natural desire to revert to what has been done in the past when things became a bit difficult. In the end the results are there to show that the upfront expenditure and investment in time was time and money well spent and the outcome has the operation well placed to manage the assets in a manner designed to deliver the optimal business outcome.

Jan 1, 2007

By K. Hopperstead

Ventilation planning in trackless metal mining is often taken for granted. This paper highlights the trials of planning and executing the ventilation design for Bog Zone at the Lisheen Mine. Ventilation planning for Bog Zone started at the feasibility study stage in 2003; subsequent design changes continued until 2006. In August 2006, the development of the Bog Zone ore body was accelerated through the use of contractors; in addition, the Lisheen equipment fleet was revised based on a larger load and haul fleet. As a result, the circuit was reviewed in terms of changes in design conditions and best practices. This review resulted in a 40% increase of total airflow required to mine Bog Zone. Resources utilized to design the circuit include: external review, computer modeling, and in-house Lisheen planning and operational staff review. The final ventilation design configuration was adopted in 2007, after modeling and evaluating 30 different scenarios, resulting in a better distribution of airflow, optimized secondary escape way, reduced contaminants, and a total power reduction. The value of investment in computer modeling of primary ventilation circuit and planning for staged implementation should never be underestimated.

Jan 1, 2009

By Kevin J. Ma, John Stankus

"In order to access remote reserve areas, some U.S. coal mines have to maintain aged underground entries for a great distance. However, high humidity, warm temperature, and time dependent deterioration can cause progressive roof deterioration and unexpected roof falls can, pose a great challenge to ground control engineers. With an active belt structure in place and limited space, re-bolting becomes very costly, less effective, and, sometimes, impractical and unfeasible. To gain long-term entry stability and serviceability, operators typically rehabilitate the aged belt entries by installing standing steel set supports. In the last several years, Keystone Mining Services, LLC, (KMS) has assisted many coal mines with their belt entry rehabilitation projects, evaluated the ground condition of various aged belt entries, and designed different standing steel set support systems. This paper presents a case study of a large-scale roof fall that occurred at an aged belt entry in a mine located in an eastern coalfield, analyzes root causes of excessive deformation of square sets that were installed in an adjacent entry, evaluates the adequacy of an existing rehabilitation square set, and develops remedial recommendations for future rehabilitation practice. Based on the case study, the paper outlines design guidelines for rehabilitation steel sets that include field evaluation, engineering considerations, design assumptions, steel structural analysis, and field installation quality control. INTRODUCTION With gradual depletion of shallow coal reserves, some underground coal mines have to maintain long-term entries (belt, track, return airway, etc.) for a great distance in order to access remote coal reserve areas. However, due to high humidity, warm temperature, and aging in the belt entry, roof strata weathering and pillar degradation become more and more severe. Progressive roof deterioration poses a great challenge to ground control engineers. Pillar rib sloughs at certain locations, entry width increases in some areas, immediate roof sags, immediate roof rock falls out between bolts, existing bolts lose functionality due to corrosion, cutters develop deeper in corners, and strata separation develops deeper up into the main roof. As a result, unexpected roof falls occur in a random manner resulting in loss of production, damage of belt structure, and even injuries to underground personnel."

Jan 1, 2017

By Thierry Bernard, J. M. Laboz

2000 HIGH-TECH SEMINAR Blasting Technology, Instrumentation and Explosives Applications

Jan 1, 2000

By C Bellia, A Maldonado, S Strong, H Baxter

This paper discusses the technical and cost benefits of alternative data collection techniques used to collect lithological information, obtain laboratory testing samples and perform in situ testing. A comparison between diamond coring and sonic coring techniques is made using data from a recent geotechnical investigation for a final pit slope cut-back. The impacts of the coring method on laboratory strength testing results, material character testing and, ultimately, the mass strength parameters and subsequent slope design adopted are compared. The sonic coring method was chosen out of necessity and enabled the collection of tube samples of a clay unit of interest as well as bulk samples for material character and geochemical testing. The sonic coring generated unexpected degradation of clastic units, while cohesive clay-dominated units were recovered well. The likelihood that disturbance due to the coring method would result in lower than expected triaxial strength results was recognised ahead of time, with surplus samples collected and single-stage triaxial strength testing undertaken. This testing compared favourably with historic three-stage testing, where sample degradation occurred during the later stages. Material character testing of fine-grained, clay-dominated units was comparable with historic diamond core testing, while grain size estimates for more clastic units tended to be finer than previous results. The use of sonic coring over non-cored methods enabled the collection of material texture data, geotechnical properties and a full suite of geochemical analyses. This provided a comprehensive understanding of the lithological and geotechnical character of the rock and soil mass. A high-confidence geotechnical model was developed. The end result was the development of a slope design that was more aggressive than was previously designed (5° steeper inter-ramp angle), which has proven to be appropriate to the conditions following excavation. Overall, sonic coring was a cost-effective means of obtaining additional geotechnical data for the site.CITATION:Baxter, H, Bellia, C, Maldonado, A and Strong, S, 2015. Case study assessing alternative data collection techniques and analysis methods to assist with geotechnical slope design, in Proceedings Iron Ore 2015, pp 419–428 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By G B. Smith

Barrick (Australia Pacific) Limited initiated a trial of Caterpillar’s Minegem autonomous loader technology in 2009 at the Kanowna Belle mine in Kalgoorlie. Autonomous loader technology offers the potential to improve loader productivity, reduce operating costs and improve safety through removing personnel from the mine operating environment. This paper discusses the implementation of the technology at the mine site, the data collected during the trial and quantifies the benefits of using automated loader technology in comparison with teleremote loader operation. The lessons learned from the trial and work planned for the future in respect of this technology is also discussed.

Mar 21, 2011

By R. M. Owens, J. F. Lupo

The Shirley Basin Uranium mine, located in southeastern Wyoming, USA, was an open pit mining operation consisting of a series of several open pit mines excavated into poorly consolidated sandstones, siltstones, and claystones. Since the initial open pits were developed in 1969, slope failures have plagued the mine and mining operations. These slope failures have persisted into the current mine reclamation period. When the mine was first developed, the open pit slopes were designed to range between 45 to 55 degrees. Numerous slope failures during mine development required the pit slopes to be redesigned with slopes as shallow as 26 degrees. At present, movements are occurring within the open pits on reclaimed slopes that are shallow as 12 degrees. Several detailed slope studies were conducted at the mine in the early 1970s. These studies, combined with more recent geotechnical investigations, provide a unique detailed history of pit slope failures on shallow slopes. This paper presents an evaluation of the slope failures at the Shirley Basin mine, highlighting important mechanisms causing slope failures on very shallow slopes. The evaluation demonstrates important key parameters for shallow slope design.

Jan 1, 2001

By Rodger C. Fry

Underground coal mining has been active within the East Mountain property since the mid 1950's. As a result, coal from two seams has been extracted within large areas allowing surface subsidence to occur. Monitoring of subsidence annually, began in 1981 using on the ground conventional monumentation, surveying and photogrammetric monitoring. The data collected has shown the time benefits of photogrammetry and the relationship between observed subsidence and the geometry of the mined out area below.

Jan 1, 1986

By Scott Chesman

Increased TBM performance is leading the way for resurgence in tunneling activity in NYC. Tunnels will be excavated in the same geologic formations as previously excavated D&B tunnels whose construction records are providing valuable insight into the prediction of rock mass behavior. This report compares an eight mile stretch of NYC Water Tunnel #2 with the recently excavated eleven mile stretch of the TBM driven Water Tunnel #3. Comparisons of the type and amount of rock support installed as well as water inflows and grout quantities are made. Rock mass characteristics specific to TBM performance are also evaluated.

Jan 1, 2005

By D. C. Brady

"Within six months from award of a project management contract, Les Mines Dumagami Limitée, Cadillac, Quebec, was operating its new hoisting facility. This was accomplished with less than a six-week shutdown of mine production while still maintaining shaft access for underground maintenance.The work involved installing a refurbished /3.5 ft diameter double drum hoist, replacing a timber headframe with a newsteel headframe, increasing the ore bin capacity from 500tons to 1000 tons, constructing a new substation, and upgrading related facilities.This paper describes the work and methods used by various contractors, Les Mines Dumagami Limitée and J.S. Redpath Mining Consultants Limited to bring this project to a successful completion. It discusses the history of the project from proposal stage through to the design, procurement, scheduling, and construction management. The paper also comments on problems that were encountered and the methods used to overcome them.IntroductionThe Donald J. Laronde Mine of Les Mines Dumagami Limitée (Dumagarni), a gold and copper producer, is located in northwestern Quebec, approximately half way between Val d'Or and Rouyn. The mine started production in the spring of 1988 and the first gold bar was poured in June 1988.Following a request by Dumagami, on February 22, 1989, J.S. Redpath Mining Consultants Limited(Redpath) delivered a proposal to increase hoisting capabilities from 1500 tpd to a minimum of 2500tpd. Although various concepts were considered, Redpath proposed a new hoist house along the same shaft axis as the existing hoist, and located on the site of the existing substation. They would then provide a new substation, replace the headframe with a largersteel structure , gain extra storage capacities by increasing the bin heights, and raising the roof of the bin house accordingly.Although underground mining would have to be stopped for a month, the mill production would be maintained by feed from Dumagami's open pit.Figure 1 shows the original plant layout and Figure 2 represents the general arrangement after the project was completed . Table 1 compares the original hoisting facilities to the new facilities.On March 2, Dumagami awarded Redpath a contract that included preliminary engineering, detailed engineering, procurement and contract administration, and later added construction management. The preliminary engineering refined the initialconcept, selected major equipment, and prepared schedules and capital cost estimates for the total project."

Jan 1, 1991

By B. T. Lusk, J. M. Hoffman, J. Silva Castro

Blast vibration induces sounds within neighboring residences. A housewide vibration and sound monitoring system was installed in a West Virginia home subjected to blasts from various distances and directions. Eighty-nine blast events were monitored and analyzed. Fifteen channels of data were collected, including data from three triaxial geophones, one airblast microphone, one uniaxial geophone mounted on the wall of the house (response channel) and four microphones that recorded CD-quality sound waves inside the house. Each of these channels was recorded on the same time scale. The response channel signal was easily separated into ground vibration and airblast-induced movement, due to differences in the time of arrival. This response channel was then compared to the sounds recorded to determine which component of blast vibration induced the maximum sound response. Blasts at distances less than 762 meters (2,500 feet) had maximum sound responses from both ground vibration and airblast, while for blasts beyond 762 meters (2,500 feet), the maximum sound response was caused by ground vibration without exception. When airblast was identified as the dominant sound generator, the peak amplitude of the sound was directly related to the amplitude of airblast. When ground vibration was identified as the dominant sound generator, the peak amplitude of sound was not related to the amplitude of ground vibration. Findings from frequency analysis showed that the frequency content of sounds inside the house was not related to the frequency content of airblast or ground vibration, regardless of source. This finding suggests that residents will have difficulty determining the source of blast-induced noise in their homes. The proposed airblast response factor (ABRF) can aid blasting operations to determine the dominant source of sounds inside a complainant’s house based on the time-of-arrival relationships. With this site-specific information, public relations responses can be developed accordingly.

Jan 1, 2010

By Liane J. Terrill

A 9O) ft (275 meter) section of a highly fractured beam of halite was mined from the roof of a supported thirteen year old drift at the Waste Isolation Pilot Plant (WIPP). The operation was conducted with a continuous miner and allowed the unique opportunity to collect spatial information on roof beam geology and to observe ground support conditions during the mining advance. Photographs and fracture maps of the mining face document the progress of the operation and the deteriorated condition of the strata. This case study details the drift's excavation and support sequences. the geomechanical response, and the conditions found in the exposed roof beam.

Jan 1, 1997

By Chandrasegaran, Tamilmani

"This paper describes a case study of a retaining wall structure using a diaphragm wall to construct a stilling basin at Tanjung Bin T4 power plant in Johor Bahru, Malaysia. The stilling basin is part of the Phase IV (T4) 1x1000MW power plant’s offshore cooling water discharge culverts. The site is located close to the sea with 5m of fill on top of very soft sediments of marine origin up to 20m thick underlain by fluvial clay and metasedimentary rock. Stringent wall deflection criteria and construction program dictated adopting an efficient solution with 800mm thick diaphragm wall supported by permanent top support as the temporary prop and improved horizontal restraint provided by deep mix piles acting as a slab (ground improvement layer) below the final excavation level. The depth of excavation is about 10.12m from the existing ground level. The proposed solution kept the wall deflection below the limit of 0.7% of the depth of bulk excavation and avoided additional props leading to faster completion of the structure. With unsymmetrical loading behind the retaining walls, 2D finite element analysis was carried out to assess the wall deflection and stresses in the wall and the grout layer below. The diaphragm wall is instrumented to monitor the behavior and the findings are discussed in the paper.INTRODUCTIONConstruction in soft marine clay has always been a challenge to the engineer because of its very low shear strength and its sensitivity to disturbance. In the case of excavation projects the problem becomes even more complicated with development of excess pore pressure during excavation. Marine clay with its low shear strength and lesser passive resistance, generally leads to large wall movements and settlement behind the wall. Increased passive resistance coming from increased number of props is useful but has its limits and it is no longer the most effective way in containing or reducing the wall movements or forces in the wall. One of the solutions to these problems is to improve the soil shear strength by means of ground improvement infront of the wall at an elevation most appropriate to maximize wall performance. There are several methods adopted in improving a soil layer including mixing additives to the ground to improve the shear strength to partially replacing the weak soil while others are fully replacing the weak soil. This paper discusses the case study of approximately 10m of excavation in soft marine clay using 800mm thick diaphragm wall supported by Deep Mix Piles (DMP) being used to improve soft marine deposit to form a slab just below the formation level and thus improving passive resistance significantly. The ground improvement layer helped to reduce the wall forces and deflections making it possible to remove the need for additional temporary props leading to significant savings is time and productivity. The paper presents the various options explored before this method is adopted, the design approach, instrumentation data and the monitored results."

Jan 1, 2015

By M. V. T. Da Silva, J. C. Harrison

Eldorado Gold Corporation of Vancouver, B.C. owns and operates three gold mines. The São Bento underground gold mine in Minas Gerais State, Brazil produced 105,907 ounces in1997. The La Colorada and La Trinidad open pit, heap leach mines in Mexico produced over 83,000ounces in 1997. With a deteriorating gold market plaguing the industry throughout 1997 Eldorado had to take critical measures at each mine to enhance gold production while lowering cash operating costs. Each mine had its own unique problems to confront. This case study will discuss three distinct courses of action taken at the three mine sites.

Jan 1, 1999