Search Documents

By Leo H. Glanville

UNTIL 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115,000 cu. ft. per min., and since then fans and sprays have been added as required. ATMOSPHERIC CONDITIONS Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the normal average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low-about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24° to 95°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,490 ft.), makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. PROBLEMS Since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination. It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By R. D. Parker

Location The Frood ore-body is expressed on surface as a prominent gossan ridge, with a total length of approximately two miles. The original Frood (the old No. 3 mine of the Canadian Copper Company) is at the southwest end of this gossan; adjoining it on the northeast is the Frood Extension (until 1929 the property of i:he Mond Nickel Company), while at the extreme northeast end is the Stobie mine. The first two of these divisions of the ridge form the Frood mine as it is known today.? This lies in lots 6 and 7 of the sixth concession, township of McKim, and is two and a half miles north of the city of Sudbury. The general elevation is 1,000 feet above sea level. The Ore-Body The Frood-Stobie parallel offset(l), as its name implies, has no connection in the field with the main mass of the Sudbury nickel eruptive-a norite. It lies one mile to the southeast of that body, and, in general, parallels it in strike. The ore occurs as a more or less tabular structure in what is known locally as the Sudbury series. They are the oldest rocks of the district, and have been placed by Collins(2) as earlier than the lower Huronian, of pre-Cambrian time. The series is comprised of sediments, volcanics (both acid and basic flows), tuffs, agglomerates, breccias, and basic intrusives, all highly metamorphosed, yet all forming a more or less regular picture. The controlling feature of the area has been the attitude of the sedimentary strata, from which has arisen the present sill-like character of the flow rocks, the basic intrusives, and the ore-body itself.

Jan 1, 1932

By S. G. Gendler

The choice of ventilation schemes in the Northern Mujsky railway tunnel and definition of the nec-essary quantities of air ensuring regulated radiation conditions in the tunnel system has been accomplished. The influence of natural draught on the stability of tunnel ventilation has been estimated. The design of a portal venti-lation gate allowing minimal influence from natural factors is described. The dependence of pressure loss in the sliding ventilation gates on their spanning value of the vehicle tunnel section has been determined. The selection of parameters for an atmospheric air heating system in winter has been carried out. The operation regimes of air heaters, dependent on the temperature of atmospheric air, have been established.

Jan 1, 2009

By A Halim

"There is still debate about who should ultimately be responsible for the ventilation system in anunderground mine. The Queensland Coal Mining Safety and Health Regulation 2001, states that adedicated ventilation offi cer is the person, while Western Australian Mines Safety and InspectionRegulation 1995 states that it is the mine manager who is responsible; the ventilation offi cer actsas the managerÆs principal ventilation advisor. This paper outlines a comparison between bothapproaches."

Jun 1, 2012

By O?Connor. D. F.

The ever increasing energy costs associated with mining at depth has become an important issue that needs to be addressed for future sustainable production. Vale Inco Limited?s Creighton Mine being the deepest has the highest energy cost per ton due to the ventilation system requirements. A review of the ventilation systems was undertaken with respect to current practices and identification of opportunities to the practical application of technology that would facilitate energy savings. Energy conservation initiatives such as time of day controls have been implemented; however there still remained some opportunity for further reduction. Based on previous studies that identified opportunities due to actual time spent in the workplace, our mining method and ventilation design, it was determined that Ventilation on Demand (VOD) could provide further additional energy reductions with respect to our auxiliary fans. A pilot project has recently been initiated to apply a Ventilation on Demand concept to two 112 kW auxiliary fans and their related workings located on the 2340m level of Creighton Mine. The project objective is to determine the practical methodology and application of this technology in the field. This project involves the installation of variable frequency drive (VFD) starters on the auxiliary fans to allow variable volume (through speed control) based on demand. The required flow is determined based on equipment and/or personnel via identification tags. The Fans adjust to the flow requirements as measured by flow sensors. Since the fans are sized for the final requirements the required flows can be achieved regardless of system length. Energy savings are realized by supplying only the volumes (power) as required and only when required. This paper discusses the rational and program being tested at the VALE Inco Limited, Creighton Mine.

Jan 1, 2009

By C. Allen

Vale Inco Ltd. is trialing several energy conservation initiatives in an effort to minimize costs and reduce green house gas emissions. The Ventilation on Demand (VOD) concept is a major project being carried out in various phases at Vale Inco mines. Due to the complex nature of a dynamic VOD system, Vale Inco is taking a systematic approach of testing VOD system components with milestone evaluations of each project. Coleman Mine was selected to pilot test the functionality and robustness of automated louvers in the underground environment; with the goal of optimizing mine airflow such that ventilation would be available for developing a new ore body. This project involved installing automated louvers in the exhaust raises; and installing variable frequency drive (VFD) starters on auxiliary supply fans. Because the VOD project created efficient utilization of the ventilation air in the 153 OB, the 170 OB is currently being developed without increasing the total fresh air into the mine. This paper describes the louver system component of VOD as applied at the mine.

Jan 1, 2009

By S. Noll

Ventilation is an essential part of any underground mining operation. It provides fresh air for workers and machinery, keeps up an adequate mine climate and dilutes and dissipates noxious gases. Possible changes in the economic environment for mining in the future, e.g. increasing energy costs, will necessitate optimization of distribution of airflow within most mines. This paper discusses the scientific set-up for measurements as well as the behavior and influence of parameters of ventilation according to airflow distribution under consideration of technically possible set-ups of mine fans. This study was done in an underground mine with a flat seam room and pillar mining method.

Feb 27, 2013

By L. Tonc

In 2004, the engineers at the Deer Creek Mine located near Huntington, Utah initiated the ventilation planning to exploit a remote area of the mine?s reserves. This area was located under a mountain which would not allow for the incorporation of an additional shaft or portal access near the proposed longwall panels. With this constraint along with the desire to maintain a two entry gate road system and the expected condition of frequent coal wash outs a ventilation plan was established. Different options were examined that included; increasing the current exhaust fan power, adding another exhaust fan installation, converting the ventilation fans in the active portion of the mine to a forcing system, and modifying the ventilation system in the active area of the mine to a push-pull system. The push-pull ventilation system was ultimately selected. This paper details the design process of the ventilation system upgrade, the procurement process for the new fans, and the new fan startup testing.

Jan 1, 2009

By Michael W. Glasson, Archie M. Richardson, Leo Gilbride, Laine Adair

Andalex Resources, Inc. recently engaged in a ventilation planning exercise that resulted in the construction of a new main fan installation to support longwall coal mining at the Aberdeen Mine. This paper documents the planning process, including underground measurements, modeling, permitting, and construction of the new fan installation.

Jan 1, 1997

By J. R. P. Aguirre

Minerales Monclova, S.A. de C.V. (MIMOSA) is owned by Grupo Acerero Del Norte (GAN). This company has 4 underground coal mines and 1 open pit to feed it?s steelmaking facilities located in the city of Monclova in the North of México in the state of Coahuila. The current underground mines are Mine 3, 5, 6 and 7 and the future projects are Mines 8 and 9. In the last years Mines 2 and 4 have been closed because they finished their coal resources. The remaining mines have bigger production and developments requirements in order to accomplish the goals of the company. The mines have been working in deeper and gassier areas. These conditions have required improvements in the ventilation design and methane control systems for all the mines. In some cases the ventilation of some of the MIMOSA?S mines has been increased 80%, and besides this, an intensive methane drainage program has been applied using horizontal in-seam boreholes and gob wells. The short-term ventilation plan includes the construction of 3 new vertical shafts with 5 and 6 meters diameter for Mines 5, 6 and 7 and the purchasing of bigger new main and backup fans for each one of these mines. One of these vertical shafts and the purchasing of the first 2 fans is already in process. This paper will explain the evolution and results of the ventilation and methane drainage systems in MIMOSA and the ventilation planning for the future years.

Jan 1, 2009

By S Bluhm, L van den Berg

In planning mine ventilation systems, heat issues are normally associated with deep-level mines where auto-compression and virgin rock temperatures play a major role. However, a number of mines suffer from high ambient temperatures and humidity, very steep virgin rock temperature gradients and an influx of hot groundwater. Mines in Australia and, particularly, South-East Asia have to deal with these environmental conditions, both in the operational and planning phases. These operations normally have to take heat into consideration during the planning stages at much shallower depths. In high rainfall regions, the water table is saturated and groundwater flow rates are particularly high, which add significant water heat load potential to the mine ventilation system.This paper considers the ventilation challenges associated with hot groundwater conditions in mechanised mines. The paper is based on specific project experience gained from a number of projects in the United States, Australia and South-East Asia and draws on data from mines that experience hot groundwater conditions. For one site, actual decline temperature survey measurements, modelling techniques, management strategies and design considerations are presented.CITATION:Van den Berg, L and Bluhm, S, 2015. Ventilation planning considerations when dealing with hot groundwater, in Proceedings The Australian Mine Ventilation Conference, pp 211–218 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Keith G. Wallace

In 1982 the U.S. Congress passed the Nuclear Waste Policy Act (NWPA) to provide for the development of an underground repository for spent nuclear fuel. This development will be managed by the United States Department of Energy. In 1986, the President selected three areas for site characterization to determine their suitability for the development of an underground repository; those sites were: 1) A site in volcanic tuff located at Yucca Mountain in Nevada, 2) a site in bedded salt located in Deaf Smith County in Texas, and 3) a site in basalt located in Hanford, Washington. At present conceptual repository designs are being developed for each site. A key element of a repository design is the underground ventilation system required to support construction, nuclear waste emplacement, and potential waste retrieval. This paper describes the preliminary ventilation system designed for the repository in tuff. The concept provides separate ventilation systems for the construction and waste emplacement activities. The paper further describes the means by which acceptable environmental conditions will be re-established to allow re-entry into previously closed rooms for the purpose of inspection, maintenance or retrieval.

Jan 1, 1987

By Richmond A

Like many industries the coal mining industry has, since the beginning of this century, undergone many changes. Technological advances and the increasing demand for fossil fuels have introduced new mining methods and techniques which allow the extraction of thicker and deeper coal seams at higher rates of production. Most new methods of mining (or for that matter any other processes) introduce problems which the engineers of the industry are expected to face and resolve. Unfortunately, spontaneous combustion has plagued the coal mining industry since the first attempts to mine coal, and is no doubt partly responsible for the reputation that coal mining is a hazardous industry. The financial loss and toll of human lives due to the occurrence of spontaneous combustion of coal in coal mines is enormous, if not incalculable. Its occurrence today is less likely to claim lives, due to both improved methods of working and in the detection of spontaneous combustion sites.

Jan 1, 1983

By Howard W. Earnest

The Rio Blanco Oil Shale Company completed a modified in situ oil shale retorting demonstration at its Tract C-a Lease in the Piceance Creek Basin of northwestern Colorado during the spring of 1982. This demonstration was the first MIS project with shafts rather than adits for access to the mining operation, and it involved several potential hazards which required that particular attention be paid to mine ventilation. Methane was first encountered during shaft sinking and ultimately resulted in the mine being classified gassy by MSHA. Secondly, we encountered hydrogen sulfide in association with the ground water, and this proved to be a more persistent problem than did the methane. Thirdly, in order to burn the underground retorts, it was necessary to provide for potential leakage of retort gases and to obtain a modification to the MSHA standard which forbids fires under- ground. This modification had a significant effect on the ultimate ventilation procedures at Tract C-a. An extensive under- ground air monitoring program was included in the ventilation system.

Jan 1, 1983

By C. Gherghel

The planning and operation of ventilation network systems for uranium mines require special considerations since ventilation is the primary technique of controlling ambient concentrations of radon progeny. The major environmental challenge facing the ventilation engineer is the requirement to dilute radon progeny to below the Working Level Month per year of worker exposure required by law. The application of large airflow volumes and the utilization of low residence times constitute some of the factors considered by the design engineer. Good mine planning and sequencing are also critical for protecting the health of miners. The mine ventilation must have such characteristics as flexibility, high air distribution efficiency, rapid air transit times, zero recirculation and no short-circuiting. A well established maintenance program for all ventilation appliances must be in place to guarantee control of the distribution system. Real-time monitoring systems permit assurance the adequate quality of air is delivered to working places. A case study for an operating mine is used to demonstrate how the ventilation system is successfully managed and operated using the above concepts.

Jan 1, 2009

By K. R. Griffin

Atmospheric conditions underground are constantly changing and from a safety perspective, it is critical to identify when conditions are trending abnormally. Atmospheric monitoring in underground coal mines allows mine operators to analyze atmospheric conditions underground in real-time. Real-time monitoring can then be used to identify whether atmospheric conditions underground have become problematic. The implementation of a risk assessment and management process allows operators to then use a risk-informed decision making to identify comprehensive site specific ventilation parameters. Establishing risk-informed ventilation parameters and tracking conditions relative to these parameters, management can modify ventilation plans as mine conditions develop to manage evolving risks. Ventilation risk assessment and management allows developing atmospheric monitoring technologies to be fully utilized in order to increase safety standards in the United States. This paper reviews general risk assessment approaches, state of the art ventilation based risk assessment, and the risk assessment and management application within the United States regulatory framework.

Feb 27, 2013

By A S. Derrington

There are several long-standing rules of thumb that are often quoted in mine ventilation studies. They include airway ‘carrying velocities’ and the critical upcast air velocity range that must be avoided to prevent a water blanket forming. Quoting these rules of thumb may lend an air of legitimacy to a ventilation design, and allow the design engineer to avoid having to study a problem from first principles. But how valid are these shortcuts in today’s rapidly changing world? This paper summarises research into the genesis of several commonly quoted rules of thumb. It finds that they were very specific to the local conditions, practices and economics at the time they were developed. It also presents examples where applying these rules of thumb outside of their original context can lead to unexpected and erroneous results.CITATION:Derrington, A S, 2017. Ventilation rules of thumb – friend or foe? Focusing on design upcast air velocities for shafts and raise bores, in Proceedings Australian Mine Vent Conference 2017, pp 253–260 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Gerrit V. R. Goodman, Edward F. Divers, Charles D. Taylor

Future mining systems will possess the ability to cut from crosscut to crosscut where advances could exceed 30.5 m (100ft). However, limitations arise when ventilating such mining systems. In deep advance mining, there will be no workers at the face to manually advance ventilation tubing or curtain. Additionally, traditional methods provide no means for maintaining face ventilation after the miner backs out. Problems such as these have suggested the need for innovative ventilation methods compatible with deep advance mining systems. The Bureau of Mines is currently considering a number of innovative ventilation schemes. One such method is the use of a jet fan to ventilate a deep cut. A jet fan is simply a freestanding fan using little or no ducting to direct the ventilation flow. Previous testing in large metal-nonmetal mine entries showed that jet fans provided adequate face ventilation for deep advances in large headings. Current testing will determine the application of jet fans in ventilating smaller coal mine entries. Another approach considered compatible with deep advance mining will use either exhausting or blowing tubing that can be remotely extended from crosscut to crosscut. During the mining cycle, such a device would extend automatically as the miner sumps into the face. The Bureau of Mines is considering several different operating designs using this tubing.

Jan 1, 1991

By D. Pienaar, D. Stanton

This paper provides an overview of possible approaches for structuring the ventilation systems for mines that will become operational within the next decade. Features addressed in the paper include: aspects of airway design and layout in the absence of centralized vertical return shafts, the impact of using diesel-powered trackless equipment in conjunction with conveyor belts in the development and production phases of the project, and the need to balance increasing electrical power costs against the requirement for reduced capital expenditure. The paper provides brief descriptions of the strategies employed in real-life situations and presents an overview of various operational parameters affecting the design of ventilation systems that will be used as ?platforms? for much deeper mines in the future.

Jan 1, 2006

This paper provides an overview of possible approaches for structuring the ventilation systems for mines that will become operational within the next decade. Features addressed in the paper include: aspects of airway design and layout in the absence of centralized vertical return shafts, the impact of using diesel-powered trackless equipment in conjunction with conveyor belts in the development and production phases of the project, and the need to balance increasing electrical power costs against the requirement for reduced capital expenditure. The paper provides brief descriptions of the strategies employed in real-life situations and presents an overview of various operational parameters affecting the design of ventilation systems that will be used as ?platforms? for much deeper mines in the future.

Jan 1, 2007