Search Documents

By K. E. Yassin, A. Yehia, M. Amar

Phosphate fines (size ≤ 45 μm), from the Red Sea Region, Egypt, were subjected to beneficiation process to recover the phosphorite grains from such fines. The sample is characterized by low P2O5 content (18.78%) associated with gangue minerals such as silica (22.77% SiO2) and carbonate (2.01% MgO) indicating its low grade. Phosphate pre-concentrate was prepared by gravity separation, using Falcon, where 63.37% of the phosphate, with 24.94% P2O5, 1.46% MgO, and 10.54% SiO2, was firstly recovered reducing the mass flow to the subsequent beneficiation process. However, the gravity tailing was the feed for the reverse phosphate flotation using bench scale column flotation where oleic acid was used as a carbonate gangue collector and amylase enzyme as a phosphate depressant. Under the appropriate flotation conditions (0.1% amylase, 5·10−4 mol/dm3 oleic acid, and temp. 30 °C), phospho-concentrate assaying 0.61% MgO, 13.14% SiO2, and 27.85% P2O5 with a P2O5 recovery of 55.45%, was finally obtained without the use of expensive depressants, e.g., phosphoric acid or sodium silicate. A tentative flow sheet for the whole process was postulated.

By K. E. Yassin, A. Yehia, M. Amar

Phosphate fines (size ≤ 45 μm), from the Red Sea Region, Egypt, were subjected to beneficiation process to recover the phosphorite grains from such fines. The sample is characterized by low P2O5 content (18.78%) associated with gangue minerals such as silica (22.77% SiO2) and carbonate (2.01% MgO) indicating its low grade. Phosphate pre-concentrate was prepared by gravity separation, using Falcon, where 63.37% of the phosphate, with 24.94% P2O5, 1.46% MgO, and 10.54% SiO2, was firstly recovered reducing the mass flow to the subsequent beneficiation process. However, the gravity tailing was the feed for the reverse phosphate flotation using bench scale column flotation where oleic acid was used as a carbonate gangue collector and amylase enzyme as a phosphate depressant. Under the appropriate flotation conditions (0.1% amylase, 5·10−4 mol/dm3 oleic acid, and temp. 30 °C), phospho-concentrate assaying 0.61% MgO, 13.14% SiO2, and 27.85% P2O5 with a P2O5 recovery of 55.45%, was finally obtained without the use of expensive depressants, e.g., phosphoric acid or sodium silicate. A tentative flow sheet for the whole process was postulated.

Upgrading of Superfine Low-Grade Haematite Ores by Reverse Floatation Direct Reduction Low Intensity Magnetic Separation Process

Sep 13, 2010

By J Harmse

This paper deals with the modernisation of the brakes on an electrically coupled Blair multi-rope hoist and covers the removal of the old calliper brakes and hydraulic control system, and its replacement with brake discs, disc braking units and hydraulic control systems. The paper covers the braking requirements of the hoist, which is made up of two electrically coupled single-drum hoists, together with the theory behind the choice of brakes and control systems supplied. The paper also covers the project logistics that were required in order to install and commission the new brakes and control systems with the minimum disruption to production on the only rock hoist on a major production shaft. Items covered include the modifications to civil works, pre-installation of bearing lubrication systems, brake discs and hydraulics and the interfacing of the new hydraulic control system to the existing electric control system. It had to be designed to be compatible to a new electric drive and control system due for installation at the end of 2005.

Jan 1, 2005

Ore textures in Australian BIF-derived ores are quite complex and have formed the basis for ore genesis models, which includes hypogene upgrading or supergene upgrading then regional metamorphism for the microplaty hematite ores and supergene upgrading for the martite-goethite ores. Despite a high level of ore texture knowledge, little is known about the spatial distribution of ore textures within deposits or their relationship to downstream processing. This paper describes a new iron ore texture classification system to better understand the vertical textural zonation characteristics of Australian BIF-derived deposits, the interpreted role of recent supergene upgrading processes on modifying primary ore textures and their implications for downstream mineral processing. The iron ore textural classification scheme presented uses textural groupings defined on the basis of similarities in mineralogy, ore texture, porosity, mineral associations and hardness. The scheme is non-genetic and has been successfully applied to deposits in the Pilbara, Yilgarn and Gawler cratons. The main ore texture groups include dense martite/hematite, microplaty hematite, microplaty hematite-goethite, martite-goethite, goethite-martite and goethite-rich. Each group can be further subdivided into physically hard to softer subcategories. The ore textural groups can be divided into those interpreted to be associated with primary replacement of BIF and secondary textures resulting from more recent modification by near-surface hydration or dehydration processes. A schematic vertical section through BIF-derived deposits consists (from surface) of detritals underlain by a carapace, both of which may have been eroded, followed by a hydrated zone with replacement of primary ore martite and microplaty hematite by vitreous goethite. The hydrated zone is underlain by 0.2 - 6 m thick zones of intense dehydration and textural infilling of porosity with hematite and hydrohematite. Immediately below the dehydration zone is a strong zone of leaching, where more porous and friable ore textures occur, followed underneath by a gradational contact with primary ore. Secondary supergene processes can impact on beneficiation with hydration and leaching resulting in more difficult density separations at the concentrator stage due to reductions in density differences between ore and gangue and loss of heavy media into pores. Supergene modification of primary BIF-derived ore textures can substantially change lump metallurgical properties, with hydration and dehydration favourably increasing lump yield but reducing resistance to thermal shock whilst leaching will give the opposing outcome. The lump properties of ore textural groups appear to be relatively consistent within and between the iron ore deposits examined.

Jan 1, 2002

By Tsunenobu Nozaki

"AbstractThe PRESS-IN METHOD is widely recognised as “an environmentally friendly piling method”. However, this characteristic is only one of the fundamental advantages of the method and this paper presents the most up-to-date capabilities of the method. Due to the evolution in recent years, the Press-in Method is now applicable to 2.5m thick retaining walls, over 50m deep foundations, overcoming rock conditions and confined construction conditions.The Press-in PrinciplesThe basis of the Press-in Method is simple. The Silent Piler presses a pre-formed displacement pile into the ground by static jacking force. The reaction for the Press-in Force is generated by gripping previously installed piles. As a pile is pressed into the ground, “A Pressure Bulb” is formed around the pile toe. Accordingly, higher bearing capacity can be generated compared to driven piles without disturbing the ground and producing any vibration. (A comparison of jacked, driven and bored piles in sand (2005), Deeks et al.)Applicable Pile ProfileThe Press-in Method is applicable to most of the steel piles available on global market i.e. U sheet pile in single form and pair, Z sheet pile, also in single and pair and Tubular Pile as described in Figure 2. Wall thickness of those piles can be 0.3m to 2.5m and moment of inertia of the wall ranges up to about nine million biquadratic cm per meter, which can deliver similar elastic modulus EI (kNm2/m) to 2.0m thick diaphragm walls and can be utilised for extremely deep excavations required in today’s construction industry"

Jan 1, 2014

By M. S. Celik

Despite its importance in various diverse industries, research on beneficiation strategies of boron minerals has not received enough attention. Boron minerals are primarily upgraded by wet processing methods. However, severe environmental constrains have accelerated the development of dry processing techniques such as calcination. Interestingly, boron minerals, colemanite, ulexite and borax undergo respectively decrepitation (fragmentation), shrinkage and expansion upon heat treatment. Each mineral then requires a different beneficiation scheme. In this study, laboratory and pilot plant studies on calcination of boron minerals conducted in our laboratories are reviewed along with their implications in commercial operations.

Jan 1, 1997

By A Giyose, V Malysiak, K Davey

Batch flotation tests were conducted on a haematite-bearing Sishen iron ore slimes sample from South Africa using reverse cationic flotation. The effect of grinding on flotation performance, the flotation response of various key impurities in the sample, and the feasibility of increasing metal recovery by refloating tailings in a scavenger flotation step were investigated. The test results indicate that reverse cationic flotation is effective in rejecting impurities from the iron ore sample tested. From a head grade assaying 6.4 per cent SiO2, 2.14 per cent Al2O3, 0.402 per cent K2O, 0.082 per cent P and 0.194 per cent TiO2, the levels of impurities were reduced to 1.83 per cent SiO2, 0.88 per cent Al2O3, 0.095 per cent K2O, 0.066 per cent P and 0.174 per cent TiO2 in the final concentrate at a Fe recovery of 74 per cent. The flotation response of SiO2, Al2O3 and K2O were found to be better than that of P and TiO2. The testwork demonstrated that grinding to 80 per cent passing about 49 microns is essential for upgrading the Sishen iron ore to produce >67 per cent Fe concentrate grade. This grind size corresponds to about 80 per cent liberation of haematite from the gangue minerals. Fe recoveries up to 76 per cent were obtained by refloating the rougher tailings in a scavenger stage, with little effect on the final concentrate grade. Size-by-size Fe recovery data obtained indicated that particles below ten microns were mostly lost in the desliming stage conducted prior to flotation whilst some reported to the froth by entrainment. Some of the coarser haematite-gangue composite particles reported to the froth product by genuine flotation.

Jan 1, 2009

By R. Elias

Botswana is a mining-dominated sub-Saharan country. Workforces are characterised by poorly educated operators and front line supervisors, with equipment and management to 1st World standards. Poor communication, ignorance of business objectives, inability to meet targets, and lack of problem-solving capacity are the norm. Training leads to high expectations and is of concern to management as a source of dissatisfaction, despite the long-term benefits higher skills have for mine viability. The aims of a technical training programme are presented with various models and approaches being implemented at operations in Botswana. These are used to construct a series of guidelines for technical training initiatives.

Jan 1, 2000

By W Newton, J Price

This paper outlines the design, justification and performance of a gravity circuit upgrade at the Marvel Loch treatment plant. The design of the upgrade was simple but effective. The key components of the upgrade were the addition of a sluice and a second Knelson Concentrator. The sluice was installed as a pre-concentration step. The upgrade also included the purchase of a Mineral Cone to treat the increased quantity of gravity concentrate. The cost was low because of the use of mostly second-hand equipment. The result was that for a cost of $75 000 the gravity recovery doubled and the overall recovery increased by over one per cent. This paper shows that you do not need to spend millions of dollars to be innovative and successful.

Jan 1, 2000

By Braja M. Das

Laboratory model test results for the ultimate uplift capacity of square and circular foundations in saturated clay (ø=0) have been presented. The results of the present model tests for square foundations have been compared with the previously published laboratory model tests results on circular foundations. Based on the comparison, it appears that the critical embedment ratio of square and circular foundations increases from about 3 for soft clays to about 7 for medium to stiff clays. By using the experimental results, an empirical procedure has been suggested for determination of the ultimate uplift capacity of belled pier foundations in saturated clay.

Jan 1, 1987

By John N. Cunningham

Despite the wide use of micropiles for rehabilitating and retrofitting existing structures, little is known regarding the load-transfer distribution of grouted micropiles in various soil deposits. The rehabilitation of a concrete-frame warehouse in Portland, Oregon, required provisions for the seismic restraint of a new shear wall; the installation of two micropiles was specified to meet project requirements. The micropiles were uncased, 19-m (63-ft) long, 200-mm (8-in) nominal diameter, and reinforced full-length with a 64-mm (No. 20) diameter hardened steel threadbar. Due to space limitations, a sacrificial, instrumented micropile was installed near the two production piles to verify design assumptions. This paper describes the geologic setting of the project within the unsaturated Missoula Flood deposits, instrumentation, load-displacement behavior, load transfer, and Beta-coefficients for the sacrificial micropile.

Jan 1, 2011

By Jueun Lee, Jong-Hwa Yoon, K. Rider, Bernard J. Martin

Whole body vibration is known to affect movement accuracy [1], however little is known about changes in the organization of movement and movement strategies used to limit the influences of perturbations. The specific aim of this work is to analyze the motion and coordination of upper body segments of seated operators performing reaching tasks under whole-body sinusoidal vibration exposure and simulated vehicle ride motion. The long-term objective is to model reach coordination and predict the dynamic behavior of the upper body motion under vehicle vibration exposure. Method The reach task consisted of pointing with the right hand index finger to targets located on touch screens placed in front of the subject, 45° overhead and 90° to the right in the mockup cabin of an HMMWV placed on a 6 DOF ride motion simulator. The task was performed under stable (no vibration) and vibration (sinusoidal vibration or simulated ride motion) conditions. A motion capture system was used to record kinematic data of reflective markers to recreate body link trajectories. Joint angles (torso, shoulder and elbow; Figure 1) were then computed using quaternions. Coordination between body links was defined as a) the joints angle-versus-angle relationships between the upper arm and lower arm, and b) the joint motion onset relationships between torso, upper arm and lower arm in the time domain. Results Angle–versus-angle relationships. The relationship between upper arm vs. lower arm angle and torso vs. upper arm angle for a far forward reaching movement in the stable (solid lines) and vibration conditions (dotted lines) are illustrated in Figure 2. Fig 2A compares the control condition with a 4 Hz lateral vibration while Fig 2B compares the control condition with a 6 Hz vertical vibration. It appears that under vibration exposure the reduced upper arm extension is compensated by an increase in torso flexion. This effect is seen in the last phase of the movements (encircled areas). In addition, the lower arm extension is delayed under 6 Hz vertical vibration (Fig 2B left panel). Time of joint motion onset. The timing relationship between torso, upper arm and lower arm is largely a function of the target to be reached. Examples of delays between body links are illustrated in Figure 3. The control condition is compared to a 6 Hz vertical vibration for three

Jan 6, 2006

By Wern-ping Chen, Jean Habimana, Jinyuan Liu, Mirza M. Rabbaig, Robert Barbour

To mitigate and control the combined sewer overflows from 17 outfalls in the City of Detroit, three outfalls in Dearborn Heights and eight outfalls in Redford Township, the Detroit Water and Sewerage Department has completed the preliminary design of a storage tunnel in 2005. In 2006, a final design has revised the alignments and the inside diameter (ID) of the tunnel. The revised tunnel system includes an 11.28-km(7-miles) 9.14-m (30-ft) ID tunnel, a 24.4-m (80-ft) ID pump station, two work shafts about 15.2-m (50-ft) ID each, and 14 drop shafts with various IDs. This paper discusses the latest development of this tunnel system.

Jan 1, 2007

The Upper Waimangaroa mining permit is part of the Buller Coalfield and lies on the eastern side of the Stockton-Denniston Plateau. The mining permit area is estimated to contain a total in-ground coal resource of 58 million tonnes, contained within 13 separate coal resource .blocks. The coal is Bituminous High Volatile B rank with export potential as semi soft coking or thermal coal. The Northern Opencast mine is the first mine proposed for Upper Waimangaroa and consists of the three resource blocks at the northern end of the permit area. The highwall of the mine will cut into the Mt William Range resulting in overburden cover of up to 150 metres in some areas. The ability to rehabilitate the area after mining was a major consideration in the design of the mine. The Northern Opencast area has been geologically mapped, extensively drilled and effectively modelled using Vulcan software. Three distinct coal seams are present and the mineable in situ resource is estimated at 8.7 million tonnes of which approximately 7.1 million tonnes is likely to be recoverable. It is proposed that this resource will be mined using opencast methods and the void will be backfilled with overburden. The life of the mine is at this stage estimated at 19 years based on an annual production of 500,000 tonnes at 1.8% sulphur and the Upper Waimangaroacoal will be blended with low sulphur coal from the Greymouth Coalfield to meet export specifications. The Northern Opencast area contains a range of native flora and fauna and physical features which make it an environmentally significant area. Mining will totally modify the area, thus an effective rehabilitation scheme is an integral part of the mine plan. Various rehabilitation methods will be used, and wherever possible, the backfilled areas will be rehabilitated so as to resemble the original area as closely as possible.

Jan 1, 1998

By R. W. Baker

"The development of uppers drilling at Brunswick Mining is reviewed. This paper describes design criteria for drilling patterns and the research required for selection of a suitable drill jumbo. The success of the uppers drilling program based on operating procedures is highlighted. IntroductionBrunswick Mining and Smelting Corporation Ltd., operates a 10 500 tonnes per day lead /zinc/copper I silver underground mine some seventeen miles southwest of Bathurst, New Brunswick .The No. 12 orebody, first discovered in 1952 by a group headed by M.J. Boylen, had extensive development, including two shallow shafts (500 ft), and test work carried out on it by St. Joe Lead between 1953-1957. However due to complex metallurgy and depressed metal prices, the operation was suspended.In 1961, a group comprised of M.J . Boylen, K.C . Irving and Patino acquired the rights of St. Joe Lead to the No. 12 property. A concerted development plan was initiated along with construction of the necessary sur face facilities and by July 1964, the property was in production at 4500 tons per day.In 1967 Noranda Mines Ltd. acquired operating control of Brunswick Mining and Smelting Corporation Ltd."

Jan 1, 1988

By M. Sandin

According to the world bank1, the mining industry consumes up to 11 percent of global energy use. In comparison, 70 percent of mining projects from the six largest mining companies operate in water-stressed regions. To steer the direction of the process industries toward more sustainable practices, more than 40 governments have adopted a price on carbon. This measure includes additional taxes on the use of fossil fuels, trade programs, new standards for renewable energy, energy efficiency mandates, more stringent emissions regulation, carbon offsets, etc. This emphasis is also supported by investors shifting their priorities to reduce risk by focusing on long-term plans, including environmentally friendly operations. The metals and mining industry is at the core of the green energy mix and electrification of vehicles. This new trend creates an astronomical increase in demand for minerals. Under a 2-degree scenario, according to the latest analysis from the world bank, as new energy technologies continue to grow, it is expected that all minerals to double in demand, and the distribution of these materials will depend on their application. • Solar panels, will account for 87% of the aluminum demand, and more than 95% of silver • Wind turbines and geothermal plants will require 98% zinc and 64% titanium. • Solar and wind energy alone will demand more than 74% of the global supply of copper, and this is without considering wiring or other infrastructure to connect the grid • Battery storage accounts for 100% of the graphite and lithium demand. (Hund, 2020) • Other materials, such as nickel and steel, are also projected to more than double in demand as they are cross-technology minerals. These materials require a manufacturing process that is accountable for the emissions proper of the transformation process. It requires that these processes move from a hindsight mode focused on reporting to a forecasting mode based on run-time measurement of GHG emissions. This is a critical first step in companies realizing an economic return for doing the right thing for the environment and their communities.

Feb 1, 2023

By George Joseph Malina

Contractor chose and Owner allowed concrete to be placed using the arch first principle while excavating the 35'-3" O.D. rock tunnel. The contract included excavating and lining 26,000 L.F. of rock tunnel to 33'-I.D. Concrete was placed at a rate of 90LF per working day using a movable bridge to allow batching, mixing and pumping of concrete adjacent to the tunnel form.

Jan 1, 1981

By Pierre-Yves Declercq, Andre Vervoort

"After the mass closures of entire coal mine districts in Europe at the end of the last century, a new phenomenon of surface movement was observed—an upward movement. Although most surface movement (i.e., subsidence) occurs in the months and years after mining by the longwall method, surface movement still occurs many decades after mining is terminated. After the closure and flooding of underground excavations and surrounding rock, this movement is reversed. This paper focuses on quantifying the upward movement in two neighboring coal mines (Winterslag and Zwartberg, Belgium). The study is based on data from a remote sensing technique: interferometry with synthetic aperture radar (INSAR). The results of the study show that the rate of upward movement in the decade after closure is about 10 mm/year on average. The upward movements are not linked directly to the past exploitation directly underneath a location. The amounts of subsidence at specific locations are linked mainly to their positions relative to an inverse trough shape situated over the entire mined-out areas and their immediate surroundings. Local features, such as geological faults, can have a secondary effect on the local variation of the uplift. The processes of subsidence and uplift are based on completely different mechanisms. Subsidence is initiated by a caving process, while the process of uplift is clearly linked to flooding. INTRODUCTION After the mass closures of entire coal mine districts in Europe at the end of the last century, a new phenomenon of surface movement was observed—upward movement in the area above the past exploitation and in the immediate surroundings. Of course, most surface movement (i.e., subsidence) occurs in the months and years after mining by the longwall method (Peng, 1986). This downward movement continues to occur at a smaller rate many decades after mining has been terminated when the water in the underground excavations is pumped to the surface. This is the case as long as a mine is in operation. However, after the closure and flooding of the underground excavations and the surrounding rock, this movement is reversed, and the surface is uplifted. A total uplift of about half a meter has been recorded to date. This phenomenon has been described in several different coal basins in Europe, for example, in Belgium (Devleeschouwer et al., 2008), France (Samsonov, d’Oreye, and Smets, 2013), Germany (Baglikow, 2011), the Netherlands (Caro Cuenca, Hooper, and Hanssen, 2013), and Poland (Preusse, Kateloe, and Sroka, 2013). To date, research has focused mainly on understanding the phenomenon (e.g., Herrero et al., 2012) and identifying general trends, whereby the link with the rise in water levels is an important issue (Caro Cuenca, Hooper, and Hanssen, 2013). The most accepted explanation is linked to the swelling of clay minerals in the argillaceous rocks in the coal strata (Herrero et al., 2012). Without doubt, the full explanation is complex, and swelling is probably not the only cause of the residual movement. Most coal strata rock is weakened upon contact with water. The increase in water pressure also results in a decrease in the effective stress. Both aspects facilitate the fracturing of rock, which normally would result in further subsidence. However, decreases in the effective stresses also result in the relaxation or expansion of the rock, which induces an upward movement (Fjar et al., 2008). All of these aspects, including the long-term residual subsidence due to compaction under dry conditions, result in a net upward movement. The phenomenon discussed here is clearly different from the upsidence, sometimes observed on other continents (e.g., in Australia, Galvin, 2016). When upsidence occurs, the rock near the surface bends and buckles upwards due to the overstressing of the floors of the valleys."

Jan 1, 2017

By Edwards A. B

Re-opening of the old Proprietary mine has provided new exposures of the system of uralite dolerite dykes observed in 19110 by the Geological Sub-Committee of the Scientific Society of Broken Hill. The newly exposed dykes have been invaded and replaced by the massive ore, with development of manganese garnet and biotite adjacent to the sulphides. A similarly altered dyke in massive ore has been encountered in the North Broken Hill mine.The textures of the unaltered portions of these dykes indicate that they have not been affected by the intense regional metamorphism that has recrystallized the other rocks of the area. Moreover, in mineral composition and textures, in chemical composition, and in cross-cutting relations, they are so similar to the uralite dolerites of the district which post-date the folding and metamorphism of the Broken Hill area, that they must be regarded as typical members of this suite of post-metamorphic dykes.The invasion and replacement of the dykes by the massive sulphide ore, and their metasomatic alteration adjacent to the invading sulphides, establishes that the lode was formed after the dykes were intruded, so that the high temperature features of the ore cannot be attributed to metamorphism and recrystallization, but are primary features of high temperature hydrothermal deposition.INTRODUCTIONTwo cross dykes are recorded on the plan of the 300-ft. level of the Broken Hill lode accompanying the report on the geology of the Broken Hill lode published by the Geological Sub-Committee of the former Scientific Society of Broken Hill (1910). One dyke occurs in Block 12, and the other in Block 13, and both were stated to consist of a dark basic amphibole rock, called diorite for convenience. The more southerly dyke was traced from some distance out in the footwall, and even through the lode, by means of occasionalpatches of it still existing in the ore, in a direction...

Jan 1, 1956