Search Documents

By E. A. Gulbransen, W. S. Wysong

THE behavior of tungsten and its surface oxides in oxidizing and reducing atmospheres and in high vacua at elevated temperatures is a question of considerable technical importance. The use of tungsten as a metal or as an important component in alloys in high temperature oxidizing atmospheres has been limited because of the unprotective nature of its oxide film and the volatility of its oxide. This paper will present results of a microbalance study1,2 of the following problems: (I) the oxidation behavior in the temperature range of 25 to 550°C (2) the reduction with pure hydrogen of thin oxide films formed on tungsten, and (3) the volatility of thin oxide films on tungsten. Tungsten is an interesting metal to study for the following reasons: (1) although the oxide to metal volume ratio is greater than one, the oxide is not considered protective, (2) the metal readily oxidizes at temperatures from 300° to 550°C (3) the oxides W02 and WO3 are reduced at temperatures as low as 500°C. by hydrogen, and (4) the oxide W02 is volatile at temperatures from 800 to 1100°C. LITERATURE The oxidation of tungsten in its thin film range has not been studied critically. In the thick film range Dunn3 has made the only systematic study. He found the oxidation rate to obey the parabolic rate law in the temperature range of 700 to 900°C. The temperature variation of the oxidation rate constant was found to follow an exponential law of the Arrhenius type. An inflection was noticed in the temperature plot of the rate law constant at 850 to 900°C. This was attributed to a phase change in the oxides. Scheil4 has studied the oxidation rate at 500 and 700°C over long periods of time and found a linear rate law. This result was interpreted as evidence for the presence of a nonprotective film. Pilling and Bedworth5 analyses of the oxide volume to metal volume ratio would indicate that a compact protective film should form. McAdam and Geil6 have studied the oxidation of tungsten in the thin film range using the interference color method. A parabolic rate law was found. Their curves showed that tungsten oxidizes faster than nickel but more slowly than iron. The lattice structures found in the oxidation of tungsten surfaces have been studied by Hickman and Gulbransen.7 They have reported that W03 is the stable oxide in contact with the metallic substrate up to approximately 600°C while W02 forms first at 700°C. Hägg and Magneli8 have recently reported a study of the lattice structures observed in the tungsten oxides using the X-ray diffraction method. In addition to an a-phase W03 and a d-phase W02, they reported the existence of two new phases. A ß' phase, homogeneous between

Jan 1, 1947

By R. B. Dunn

Whilst coalmining in the United Kingdom has been synonymous with longwall mining practice there have been changes in recent times which have enabled not only an extension in the length of the face to be worked but also in the ability to extract both thick and thinner seams. Additionally the industry has taken a positive view in the extension of retreat methods of extraction applied for different reasons both to particularly thick and specially thin seams. To permit development of a flexible programme to meet these diverse needs, it has been necessary to design machinery along with mining systems specially suited to these requirements. In reviewing current UK thinking special emphasis is made on the extraction of thinner seams generally of higher quality coal at moderate depths with a commentary on some recent results.

Jan 1, 1979

By B Roache

Ground support installation into the face of development headings has become an accepted practice at many Australian hard rock mines. Ground support is installed in the development face to reduce personnel exposure to rockfall while conducting work tasks such as marking up, installing lifter tubes, charging, and face sampling. The ground support system installed in the face is typically friction bolts and mesh. This support system can be effective at reducing rockfall occurrence, but it also increases the cost of development per metre, in terms of capital for the ground support, jumbo and operator capital allocation and the installation time slowing each drill and blast cycle. Other issues associated with meshing and bolting the development face include management of rock bolts and mesh sheets in the fired dirt of every cut, damage to services such as vent duct, geometry issues when installing ground support onto irregular development profiles and operator error. Fibrecrete installation onto the development face for support is an option considered by many mines, but it can be difficult to manage due to the removal of visual indications of misfires and slowing the mining cycle due to the wait time for fibrecrete curing. The use of Thin Spray Liner (TSL) products in underground hard rock mines has been relatively infrequent in the past, mainly due to issues with cost, health and safety, and liner strength. Kanmantoo Mine investigated the use of TSLs for the purpose of development face support, while collecting data on the costs and practicalities associated with their use. Several TSL products were trialled and a preferred TSL product was selected for use as face support. Cost savings, drill and blast cycle timing improvements and other benefits were achieved while meeting the requirement to reduce rockfall risk.

Mar 29, 2023

By C. Graham

Thin Spray-On Liners (TSLs) have been researched and in development for over two decades and yet their fully functional and widely justifiable application in mining has yet to be achieved. While the explanation for this is partly technical, it is also clear that proving and communicating the operational and economic case for why a mine should change from mesh or shotcrete liners to a TSL is not a trivial matter. Evidence must be presented and communicated effectively, that is both obvious and compelling for a mine operator. The paper describes recent work carried out and directed towards this end, with funding from CAMIRO?s Deep Mining Research Consortium and additional support from 3M Canada and ABB Canada. The essential progress that has been, or is in the process of being made, will be described in providing the necessary proof of acceptable or superior TSL performance in the following areas: polymer formulation, health and safety, geotechnical specification, robotic liner application, business case economics and yielding ground support effectiveness. Future plans are also presented to demonstrate the performance of a new 3M composite TSL/yielding bolt support system in underground trials where the substrate rock is intended to fail through a number of mining-induced mechanisms.

Aug 1, 2013

By Andriy Burbelko, Daniel Gurgul, Wojciech Kapturkiewicz, Marcin Gómy

"The mathematical model of the globular eutectic solidification in 2D was designed. The proposed model is based on the Cellular Automaton Finite Differences (CA-FD) calculation method. The model has been used for studies of the primary austenite and of globular eutectic grains growth during the ductile iron solidification in the thin wall casting. The model mentioned above takes into account, among other things, non-uniform temperature distribution in the casting wall cross-section, kinetics of the austenite and graphite grains nucleation, solute diffusion and non-equilibrium nature of the interphase boundary migration.Some aspects of stochastic nature of the solidification processes are taken into account. The results of the CA solidification modeling have been shown, that differences between cooling curves obtained in the same conditions of the casting solidification may be a result of the stochastic nature of the grain nucleation.The results of modeling were compared with the experimental microstructure. The model is well worked for thin walled ductile iron casting, for fast solidification process.IntroductionNodular graphite cast iron, also known as ductile iron (DI), has major applications in critical engineering parts due to its mechanical properties and castability. The mechanical and physical properties of this material depend on the shape and number of the graphite grains andmicrostructure of the metallic matrix.Solidification of DI was a subject of many computer modeling programs described in literature [ 1-5], in which the stationary conditions of carbon diffusion in austenite is pre-assumed. Recently, a tendency for production of thin-walled castings has been observed [ 6-8]. In this technology, the process of the fast solidification may be very far from equilibrium and steadystate conditions [9].The purpose of the present work is a two-dimension model development for simulation of the DI structure formation during the solidification in the condition of non steady-state temperature and diffusion fields in the thin-wall casting.Model of process The CA-FD is one of the known methods of the simulation ofmicrostructure formation during the solidification [ 10, 11]. In the CA microstructure modeling the outer grain shape is the result of the simulation and does not superimposed beforehand. The model development for a onephase microstructure evolution is a subject of the numerous researches [12 -23]. Model of the eutectic solidification of DI in the uniform temperature field and superimposed cooling rate is known [24]."

Jan 1, 2013

By Greg Smith

This paper documents the use of bench testing equipment developed to enhance the understanding of, and improve upon, common roof bolt support systems. Most roof bolt systems consist of components that are covered within the scope of ASTM (American Society for Testing and Materials) standards. However, ASTM does not specify testing methods or performance standards for complete roof bolt ?systems?. It only designates testing methods and minimum performance standards for roof bolt ?components?. Improved understanding and continuous improvement of these systems is essential given the enormous impact that they have on the safety and profitability of underground mining operations. Bench testing equipment has been developed that effectively measures and records multiple points of deformation in a rock bolt support system while load is being applied. With this testing capability, an improved understanding of component and system stress distribution can be obtained and devices and methods for visual load indication can be developed. This paper is formatted as case studies where testing was performed to demonstrate load versus deformation profiles and to develop system improvement products.

Jan 1, 2012

By B. Anderson, P. Churak, S. Dewar, A. Johnson, P. Eger

Although vegetation can be successfully established on fine taconite tailings, innovative approaches are needed to reclaim the coarse tailings used for dam construction. Through a series of cooperative projects with various government agencies and industries, EVTAC has been able to develop a unique closure plan. This plan will not only meet current reclamation standards, but also provide mitigation for a disturbed wetland and possibly create a tree plantation in the interior of the basin. By using waste products and exchanging materials, reclamation of the entire basin will be accomplised in a cost effective manner.

Jan 1, 2002

In the last 30 years, human appropriation of global renewable resources has accelerated to the point where 35 per cent of the earthÆs land surface is now in managed agro-ecosystems, consumptive water use consumes between 50 per cent and 85 per cent of freshwater supply and 60 per cent of ecosystem services are utilised in an unsustainable manner. There are virtually no landscapes in which renewable resources are not already fully allocated among different economic and environmental uses. Furthermore, it is increasingly recognised that water availability issues do not exist in isolation but are linked with the related environmental issues of biodiversity preservation, the carbon cycle, soil degradation, and energy use and supply. It is against this background that the sustainable management of water in mining is increasingly developing a strategic viewpoint where water is viewed as a resource within an interconnected landscape, having economic, environmental and social value and providing a range of environmental services in the provision of public and private goods. This paper explores the issues associated with sustainable management of water in mining from a strategic viewpoint. The cumulative impacts of multiple water users, both within and outside the mining sector, is increasingly threatening the security of supply for all users. To quantitatively assess the ætrueÆ value of water it is necessary to: Better understand the science of ecosystem functioning and how human actions impact on environmental processes. Develop appropriate policy, finance and governance structures to support innovative programs that preserve ecosystem function and services (including market based instruments). Apply knowledge as interventions across landscapes in ways that maximise benefits and minimise unintended consequences taking into account differences in the value of water among sectors. A strategic viewpoint of water management relies on knowledge to guide decision making that has been acquired at a range of scales from mine site to mining region. This knowledge must be based on rigorous science, sound data and syntheses of different types of information. Strategic management of water resources will better position the industry in terms of understanding the risks posed by complex, interlinked environmental issues that are increasingly impacting on future access to land and renewable resources, including water, thereby ensuring miningÆs future social licence to operate.

Jan 1, 2009

By P. K. Sharma

The acidophilic and chemolithotrophic Thiobacillus ferrooxidans bacteria grown in the presence of soluble ferrous ions and solid substrates (sulfur, pyrite and chalcopyrite) as their energy source have been used in the investigations. The cell surfaces are characterised by zeta-potential, contact angle, FT-IR and FT-Raman studies. The adsorption isotherms of the cells on pyrite and chalcopyrite indicate that the adsorption begins on pyrite at a much lower equilibrium cell population than on chalcopyrite. The isotherms tend to level off at a cell adsorption density corresponding to a horizontal monolayer coverage when the geometrical dimensions of the cells are considered. In the presence of cells, the xanthate flotation of pyrite completely depressed, whereas chalcopyrite flotation is unaffected. The results suggest that chalcopyrite can be selectively floated from pyrite, also at a neutral pH region, in the presence of T. ferrooxidans cells.

Jan 1, 1999

By Ronel du Plessis, John C. Davidtz, Jan D. Miller

Recent results from electrochemical measurements demonstrate that trithiocarbonate (TTC) collectors are more readily oxidized to their corresponding dithiolates than the dithiocarbonate/xanthate (DTC) collectors. Based on the traditional analysis of collector adsorption, trithiocarbonates might then be expected to be effective for bulk sulfide mineral flotation. Previous bench-scale flotation research had shown that TTC collectors are very effective for the flotation of copper sulfide minerals and PGM (platinum group metal) sulfide minerals. More recently, the TTC collectors were evaluated for auriferous pyrite recovery in benchscale plant scale flotation testing in the United States and in plant tests at Anglogold in South Africa. TTC collectors were also applied in bench-scale testing of a PGM ore. In each case an improved separation efficiency was realized. Fundamental studies at the University of Utah examining the effect of collector structure (functional group, -O-CS2 versus .S-CS2), specifically with respect to auriferous pyrite flotation, are in progress. The effect of collector structure was evaluated with air as well as nitrogen as the flotation gas medium. Experimental techniques utilized included electrochemically controlled contact angle measurements to evaluate mineral hydrophobicity and infrared spectroscopy to explain collector adsorption phenomena at the mineral surface.

Jan 1, 2003

Dravo Corporation was founded in 1891 and has long been recognized as a major domestic engineering and construction firm headquartered in Pittsburgh. In 1977, Dravo had revenue of $852.2 million with international business activities contributing $248 million; quite a different picture than envisioned at the turn of the century. Engineering and construction activities still dominate Dravo's most recent history and will do so for the immediate future. However, fluctuations in capital spending by large industrial sectors of our economy during the late sixties were affecting Dravo's planning for continued growth along its traditional lines of business. Diversification was a possible solution to smooth out the upward trend in corporate earnings. One large result of these continuing efforts was the formation of Dravo Lime Company, a vertically integrated, proprietary chemical supplier for the air pollution control market. Briefly retracing the seventies, the passage of the Federal "Clean Air Act" in 1970 supplied the impetus for Dravo Lime Company. This law promulgated limits on the emissions of sulfur dioxide (SO2) from large stationary sources that would affect local air quality. The major industry that felt the brunt of this regulation was the electric utility industry, especially those generating electricity with coal-fired boilers. The law hastened the development of a new industry, flue gas desulfurization (FGD), and is composed of three major segments: (1) the electric utility, (2) the FGD equipment suppliers (the scrubbing modules), and (3) the scrubbing chemical suppliers. Dravo's experience suggested the equipment end of the business but market analysis indicated that our long range corporate goals could be better attained by investigating the chemical processes involved in the removal of the SO, gas. The result being Dravo Lime Company. This paper will briefly describe the Thiosorbic lime scrubbing process and review our innovative mine and calcining facility.

Jan 1, 1978

By Mark Aylmore, Guy Deschenes

"Increasing pressure are motivating the gold mining industry to develop a substitute to cyanide for leaching gold. This effort in mainly based on the high toxicity of cyanide and on the lack of efficiency of cyanide in the treatment of mildly refractory gold ores (sulfides and pre-robbing). Consequently, in only a few years, consortia have been created to elucidate and implement a new technology. The most promising lixiviant that has been selected to replace cyanide is thiosulfate. This paper will present a critical analysis on the latest developments in thiosulfate leaching and illustrate the potential and limitations of the technology with experimental data. Finally an assessment of the cost and performance of thiosulfate leaching relative cyanidation will be evaluated.INTRODUCTIONConcerns regarding the toxicity of cyanide and inability of cyanide solution to effectively leach some carbonaceous gold ore or mild refractory gold ores have made the gold mining industry evaluate alternative lixiviants to leach gold. This concern has been heightened recently by the cyanide spill at a mine in Romania, which devastated a 250-mile stretch of the Danube River and its tributaries, and the environmental damage at Ok Tedi mine in Papua New Guinea. Some countries and locations have prohibited the application of cyanidation to recover gold, such as, California and Colorado States, Japan and Turkey etc.There are several potential non-cyanide lixiviants (Sparrow and Woodcock, 1995) for gold extraction, such as thiosulfate, thiourea and halogen. A pilot feasibility test (Marchant and Broughton, 1987) had suggested that thioureation might result in acutely toxic byproducts even after treatment. Scientists of Swedish Academic of Sciences reported that thiourea is a carcinogen. Halogen is also a pollutant to the environment. Thiosulfate leaching appears to have very good potential as an effective and less hazardous procedure for gold and silver extraction from auriferous ores. In addition to being much less toxic and relatively cheap, it forms a stable anionic complex with gold but is less reactive to other metals, for instances, copper and carbonaceous materials, in comparison with cyanide."

Jan 1, 2001

By R. Y. Wan

Newmont Gold Company has advantageously used the capabilities of mineral oxidizing bacteria to develop a process for pretreatment of low grade sulfidic and carbonaceous-sulfidic refractory gold ores. The biooxidation process results in the oxidation of the sulfidic minerals with increased exposure of gold for subsequent gold recovery. The biooxidized carbonaceous-sulfidic ores cannot be heap leached with cyanide because of the "preg-robbing" characteristics of the carbonaceous matters in the ores. An alternative heap leach process using ammonium thiosulfate was developed to extract gold from the "preg-robbing" biooxidized ores. The ammonium thiosulfate leach process has been successfully practiced both in laboratory and pilot plant testing. Satisfactory test results encourage the continuation of process development.

Jan 1, 1996

By I. H. Gundiler

Although cyanidation has been universally applied in the processing of gold and silver ores, the search for less toxic alternatives continues. Difficulties encountered in processing ores containing oxidized copper minerals and the inherently slow kinetics of cyanidation have generated a renewed interest in thiosulfate leaching. This process, as well as the catalytic effects of copper ion, were well recognized and widely applied towards the end of the past century. In this study, the effects of copper, ammonia, and thiosulfate concentrations on gold dissolution were investigated using the rotating disk technique. Extraction of gold and silver from an oxidized copper-bearing ore was also studied utilizing a statistical experimental design, and these results were displayed in the form of contour plots.

Jan 1, 1993

By P Breuer, X Dai, A Bergamin, D Hewitt

"Copper-ammonia-thiosulfate?leaching of gold has been researched for several decades as a potential alternative to cyanidation. However, this technology has not yet been applied commercially due to many challenges such as complex solution chemistry, reagent degradation and losses, system instability with losses of precious metals and difficulties in gold recovery from the leachate. Progress has been made at CSIRO in tackling some of these challenges including:better understanding and control of the leach conditions to minimise reagent losses whilst maximising gold recovery use of strong base ion exchange resins to recover the gold strategies to deal with polythionates that adsorb competitively with gold on ion exchange resins development and evaluation of process flow sheets.As a result there has been increased interest from the gold industry and renewed activities to develop thiosulfate based processes for gold recovery. One application area, which has been developed to the point of piloting, is the treatment of gravity gold concentrates using a copper-ammonia-thiosulfate leach with ion exchange recovery of the gold thiosulfate. This paper describes some of the advancements in the development of a potential process flow sheet for this application.CITATION:Dai, X, Breuer, P, Hewitt, D and Bergamin, A, 2013. Thiosulfate process for treating gold concentrates, in Proceedings World Gold 2013, pp 61-70 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 26, 2013

By J Langhans, Y Choi, Q Wang, J Y. Baron, P Kondos

Barrick has successfully developed the thiosulfate leaching process to treat sulfidic high preg-robbing ores. The process was developed through rigorous bench test programs and proved in pilot campaigns and demo plant operations. The process uses calcium thiosulfate as a leaching reagent, resin for gold recovery with sulfite/trithionate elution and reverse osmosis as a mean of reagent recovery. The thiosulfate leaching plant is under construction as a brownfield project and the start-up is planned in 2014 at Goldstrike, Nevada, USA, one of BarrickÆs operations.CITATION:Choi, Y, Baron, J Y, Wang, Q, Langhans, J and Kondos, P, 2013. Thiosulfate processing - from lab curiosity to commercial application, in Proceedings World Gold 2013 , pp 45-50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By O. Celep, H. Deveci, Ersin Y. Yazici, F. Ahlatci

"There are increasingly stricter environmental regulations imposed for use of cyanide leaching for the extraction of gold from ores. Alternative lixiviants to cyanide, preferably with low toxicity, have been extensively studied. Thiosulphate has emerged as one of the most suitable alternative leaching agent in place of cyanide due to its low toxicity and technical attributes e.g. fast leaching kinetics, high gold extractions from carbonaceous ores in particular. High solubility of most copper minerals in cyanide solutions results in low gold extractions due to excessively high consumption of cyanide. In contrast, low reactivity of copper minerals in thiosulphate solutions makes thiosulphate leaching potentially suitable alternative for treatment Cu-bearing gold ores. The extraction of gold/silver from a copper-bearing pyritic gold concentrate (62 g/t Au, 110 g/t Ag and 0.3% Cu) in thiosulphate solutions was investigated in this study. The concentrate is composed of predominantly quartz (25%) and pyrite (32.7%) as well as sphalerite (5.37%), galena (2.12%) and anglesite (1.13%). Other minor minerals are arsenopyrite, chalcopyrite, covellite and bournonite. Previous studies by the authors indicated that the concentrate did not respond well to cyanide leaching (i.e. 45-46% Au/Ag at 1 g/L NaCN). The effects of concentration of ammonia (0.2-1.5 M NH3), thiosulphate (0.1-0.75 M S2O3) and copper (0-20 mM CuSO4) on the extraction of gold and silver over 8 h. was investigated. Increasing the concentration of thiosulphate and ammonia substantially improved the rate and extent of gold leaching while high copper levels produced an adverse effect particularly at low concentration of thiosulphate (i.e. 0.1 M). Complete extraction of gold was achieved under suitable conditions. In contrast to gold, silver extractions remained consistently at low levels (i.e. 28%). These findings demonstrated that thiosulphate leaching could be used to achieve acceptable levels of gold extraction from the copper-bearing pyritic gold concentrate."

Jan 1, 2018

By J. Brent Hiskey

Thiourea is a reagent capable of complexing gold and silver. With the proper oxidant, thiourea can effectively dissolve metallic gold and silver. A thiourea leaching system possesses potential advantages over conventional cyanidation including acidic solutions instead of alkaline, cationic complexes in contrast to metal-cyanide anoionic complexes, and faster leaching rates with acidic solutions of thiourea. Generally, the rate of metal dissolution in thiourea solution is fastest when ferric ion is employed as an oxidant. Acidic thiourea solutions for certain applications could offer a nontoxic and noncorrosive option for processing gold and silver. This paper provides information regarding the fundamental chemistry of the acidic thiourea system, and reviews the dissolution of both silver and gold in acidic solutions of thiourea. The recovery of gold and silver from acidic thiourea solution is discussed.

Jan 1, 1981

By J. B. Hiskey

Thiourea is a reagent capable of complexing gold and silver. With the proper oxidant, thiourea can effectively dissolve metallic gold and silver. A thiourea leaching system possesses potential advantages over conventional cyanidation including acidic solutions instead of alkaline, cationic complexes in contrast to metal-cyanide anionic complexes, and faster leaching rates with acidic solution of thiourea. Generally, the rate of metal dissolution in thiourea solutions is fastest when ferric ion is employed as an oxidant. Acidic thiourea solutions for certain applications could offer a nontoxic and noncorrosive option for processing gold and silver. This paper provides information regarding the fundamental chemistry of the acidic thiourea system, and reviews the dissolution of both silver and gold in acidic solutions of thiourea. The recovery of gold and silver from acidic thiourea solution is discussed.

Jan 1, 1981

Factors which cause thiourea consumption in gold-leaching systems include adsorption by gangue mineral particles, complexation with base metal ions, thermal degradation, and oxidation by air/ferric iron. Of these factors oxidation by ferric iron is the most significant factor. Of course, ferric sulfate is desired as an oxidant for the gold leaching reaction, but an excess of ferric sulfate leads to high thiourea consumption. In this regard, the rate of gold leaching by thiourea must be balanced against the rate of thiourea decomposition. It is important to note that the thiourea decomposition reaction in ferric sulfate solution is relatively slow in pure solutions and has been found to be first order with respect to both thiourea concentration and total ferric iron concentration. However, when mineral particles from gold-bearing ores or concentrates are present, the decomposition rate can become quite significant. As might be expected, the catalytic activity of mineral surfaces varies with particle composition and size. Experimental results are discussed with respect to the consumption of thiourea.

Jan 1, 1997