Search Documents

By Utley Wedge

(Cleveland :Meeting, October, 1012.) In general, the art of securing copper from sulphide ores or concentrates may be said to consist of : (1) separation, in the molten state, of copper sulphide with some iron sulphide, from the great bulk of gangue-material, followed by (2) elimination of sulphur and iron from the molten matte, by oxidation and fluxing, leaving metallic copper. The definition is made broad enough to cover the general practice, whether or not the ore or concentrate is given a preliminary roast for the removal of surplus sulphur. The above process, which I will designate as the smelting process, makes necessary the presence in the ore, or the addition thereto, of such silica, lime, and iron as may be necessary for the formation of a light and fusible slag, together with sufficient sulphur and iron for the formation of copper-matte, and also the addition to the matte of sufficient silica for the oxidation and fluxing-out of the iron. These items, together with the cost of fuel sufficient for melting the mass, constitute important items of cost in the copper-smelting process. Numerous cases where fluxing-materials are scarce or dear, or where fuel is expensive, have caused special attention to be given recently to the wet process of copper-extraction, which may be designated as consisting of forming soluble copper salts which are then washed or leached out of the ore or concentrates by dissolving in water or acid. Metallic copper may then be secured from the solution of copper salts by electrolysis; by cementation; or copper can be brought out of the solution as a * Presented also at the Joint Meeting of the Institute and Section IIIa, Metallurgy and Mining, of the Eighth International Congress or Applied Chemistry, New York, N. Y., September, 1912, and here published by mutual agreement.

Dec 1, 1912

The ore, as sent to the sulphide mill, is a mixture, in varying proportions, of oxidized ore from above the 450-ft. level and sulphide ore from above and below (to date mainly from above) that level. The oxidized ore consists essentially of quartz, with varying amounts of kaolin and clayey material which passes into the slime and, in excess, creates a serious problem in settling. Pyrite may be present in small amounts. The gold is free and extremely fine.The ore, classed as sulphide, consists of pyritic material in a quartz gangue. The sulphides have been exposed to weathering, leaching by descending solutions and attack by ascending gases and actual burning. The alteration products occur in widely varying proportions and this variation adds to the difficulties in settling and control of grinding and flotation.Copper Minerals.-Chalcopyrite is the principal copperbearing mineral with smaller and varying amounts of covellite, which is sometimes associated with chalcocite, both these minerals being apparently of secondary origin.Examination of tailing by Dr. Stillwell has revealed all stages between clean chalcopyrite, chalcopyrite tinged with covellite, covellite with residual cores of chalcopyrite and clean covellite.The chalcopyrite is free floating, very few particles of clean chalcopyrite being observed in the tailing from granular flotation. The chief tailing loss is probably as chalcopyrite occurring as small inclusions in pyrite...

Jan 1, 1939

By L. C. Graton

I. INTRODUCTION. The Relations of Scale in Geologic Work. MANY features of human accomplishment rest upon the possibility of representing natural objects on a scale of different magnitude from the actual one. Most drawings, for example, are of very different scale from that of the object depicted, and indeed are useful mainly on this account. More important than the question of mere convenience, however, is that of meeting the physical limitations of vision.1 Thus, a mural

Jan 5, 1913

By William Phillips

THE earliest mention of the sulphur deposits in what is now Culberson County, Texas, seems to be contained in "Explorations and Surveys for a Railroad Route from the Mississippi River to the Pacific Ocean, United States War Department, 1853-54." Captain John Pope (he was not commissioned Captain until 1856) had charge of one of the divisions of the Survey. In his report on the geology of the route, William P. Blake noted the analysis of a greenish earthy powder from the bed of Delaware Creek, at the springs, which contained 18.28 per cent. of free sulphur. The report states: "From the chemical examination of the waters of the spring, by Dr. Booth, it appears that chloride of sodium is the principal solid ingredient, but considerable quantities of sulphide of sodium are present. * * * * * The waters from the springs examined by Dr. Booth were alkaline, but it is possible that some of the springs are acid; and in this case the precipitation of sulphur would ensue on the mixture of the acid waters with those charged with alkaline sulphurets and the origin of the deposits of sulphur would he thus explained." This is the first reference to the existence of sulphur in that region, the first mention of the character of the water found there and the first suggestion as to the' origin of the deposits. The possibility of the existence of acid waters was confirmed by E. M. Skeats, nearly 50 years later.1 In this publication, Skeats says that the water from the sulphur deposits in Section 11, Block 114,, Township 5, contains 79.08 grains of free sulphuric acid per gallon. This locality is about 13 miles (21 km.) south of Delaware Creek and about 35-miles (56 km.) east of the Delaware Springs. The next published reference to the existence of sulphur in Trans-Pecos Texas is in the First. Annual Report of the Geological Survey of Texas, 1889, page 226, where W. H. von Streeruwitz mentions that sulphur is found in that region, but gives no further information. In the

Jan 9, 1917

By Neill A. O, Worth I, O&apos

The formation of Kalgoorlie Consolidated Gold \lincs 1't% Ltd hati pla,xd all the major the gold producing areas adjacent to the city of Kalgoorlie/Boulder under one management, enabling the development of the 'Super Pit'. This has facilitated the economic optimisation of the resource. Optimisation has been achieved by the timely collection and presentation of data and the use of these data to reduce costs and improve planning procedures.In particular the following issues have been addressed:ò the reduction of the impact of the mining activity on the adjacent urban population centre,ò implementation of safety procedures for mining through underground voids,ò the determination of the optimum bench height and mining method for ore production benches and blast design. This system is fundamentally based on maintaining a high degree of selectivity while achieving a balance of relatively low unit operating costs,ò assessment of the comparable benefits of contractor versus owner operated earth moving equipment, andò the development of effective ore body models, production reconciliation and the long term mine planning procedures to facilitate effective strategic planning.

Jan 1, 1993

By H. D. B. Wilson

THIS PAPER has resulted from a preliminary draft of a background paper prepared anonymously for the Science Council's Special Study of the Solid-Earth Sciences in Canada. The draft was circulated to eighty-four Canadian geologists; forty-eight of these responded with criticisms of the draft. All critical re-marks were considered carefully and most have been incorporated in the final paper in an attempt to balance the author's bias, although this bias undoubtedly still appears. Indications of support for a particular statement or section were also helpful, because many of these contradicted criticisms and enabled the author to judge the consensus. Thus, all criticism could not be incorporated because the referees did not agree. It is interesting that some remarks were con-sidered overstatements by some and too bland by others. The most perplexing critical comment was one which suggested a new author was needed, and went on to name the existing author as the most likely candidate.

Jan 1, 1970

By T Berryman, C Adams, L Griesel, C Buxton

The Kalgoorlie Consolidated Gold Mines (KCGM) schedule model is used for short- to medium-term planning and scheduling at the Fimiston Open Pit Mine (the Superpit). The model bridges the gap between grade control models, which are generated one to seven days prior to mining, and the annual Resource and Reserve model update that is used for budget and life-of-mine plans. The schedule model uses close-spaced grade control data (up to 20 000 m drilled each month) as well as resource definition drilling to estimate production volumes three to six months ahead of current mining. From this, a rolling 12 week mining and processing schedule is generated on a monthly basis. As the KCGM operation is mill and sulfur constrained, the schedule model needs to be an accurate predictor of ounces as well as tonnes, gold and sulfur grades. The process must also be time efficient in order to meet monthly planning and reporting deadlines. Due to the large amount of new data generated each month, model updates using conventional interpretation and estimation techniques have proven to be impractical and too time consuming. This paper will examine the evolution of the Superpit schedule model process over time, recent improvements and the effect of different model outcomes on short- and medium-term mine planning.CITATION:Griesel, L, Buxton, C, Adams, C and Berryman, T, 2014. The superpit schedule model – A time-efficient data-driven estimation for short- and medium-term planning, in Proceedings Ninth International Mining Geology Conference 2014 , pp 397–410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By J. Ivon Graham, T. D. Jones

This paper presents methods in use in British coal-mines for the suppression of dust. While the effect of present-day treatment will not be apparent for several years, in pits in South Wales, concentrations as high as 50 gm./1,000 cu. ft. were some years ago fairly common in various operations at or near the coal-face, with an average concentration of 20 gm./1,000 cu. ft. Now the average concentration in what were previously dusty pits is probably not greater than 3 gm./1,000 cu. ft.Nevertheless, every effort must be made to improve conditions still further. In South Wales it is claimed that 99% of the coal-faces requiring treatment have been dealt with either by wet cutting, infusion, or hand-spraying. The extent of the treatment by these methods can be gauged by the fact that the total length of coal-faces now being treated by water infusion in Cardiff and Swansea areas is about 33,000 yds., by wet cutting 25,000 yds., and by hand-spraying nearly 14,000 yds. The influence of methods of mining upon dust production is only mentioned very briefly in this review, and there is no doubt that much more is to be learned concerning this aspect. It can be stated, however, that good mining practice is essential to prevent unnecessary dust production, and the problem of dust in mines will be solved only by the closest co-operation between mine managers, workmen, and scientists.

Jan 1, 1947

By L Reynolds

Oceana Gold (New Zealand) Limited (OceanaGold) has commenced mining operations at the Globe-Progress mine in the Reefton Goldfield, an area that historically produced 2.1 million ounces of gold from underground quartz lode deposits. During the construction phase of the operation, advanced exploration programmes targeting near-mine prospects commenced. The focus of this ongoing exploration is the discovery of near surface, refractory gold deposits that are amenable to open-pit mining methods and treatment through the Globe-Progress process plant.   One such discovery is the Supreme deposit, located along strike approximately 3 kilometres to the south of the Globe-Progress mine. The Supreme area was tested extensively with diamond drilling in 2006, defining a deposit with similar mineralisation styles and grade to the Globe-Progress deposit. The mineralisation comprises a central core of gold-bearing quartz veins, locally containing visible gold, surrounded by a more extensive halo of refractory, disseminated gold associated with an arsenopyrite-pyrite sulphide mineral assemblage. Three subparallel mineralised structures host the mineralisation. These structures are highly oblique to the country rock orientations, extending approximately 250 metres along a northeast-southwest strike and at least 220 metres down-dip, with an average thickness of 12 metres and moderate dip to the southeast. Records of historical workings indicate that mineralisation extends further down-dip and remains open at depth. 5175 ounces of gold were mined historically at the Supreme deposit. OceanaGold have defined an Inferred Resource for the Supreme deposit of 0.84 million tonnes at 1.46 grams per tonne for a total of 40 000 ounces (at a 0.8 grams per tonne cut-off). Higher-grade zones of mineralisation exist within the deposit and further drilling is planned to test the extent, continuity and geological controls of the mineralised structures.

Jan 1, 2007

By R. Xie, J. Liu, Y. Zhu, Y. Li

The surface chemistry features of spodumene and feldspar were investigated by XPS, zeta potential measurements and first principle calculation. The results indicated that the zeta potential of feldspar was more negative than that of spodumene. The most possible active sites on spodumene and feldspar were Al sites and O sites. However, the number, type and activity of these sites were different. The flotation behaviour of five new collectors (cationic collector decyloxy-propyl-amine (DPA), anionic collector α-bromododecanoic acid (α-BDDA), N-Dodecyliminodiacetic acid (DIDA), and mixed collector DPA-BDDA and DPA-DIDA) were investigated through micro flotation experiments and analysed based on the surface chemistry features of spodumene and feldspar. The results revealed that cationic collector DPA processed a high collecting capacity for both minerals. The highest recovery of spodumene and feldspar was 91.60% and 95.30% respectively. The anionic collector α-BDDA and DIDA showed poor flotation behaviour. The recovery of spodumene and feldspar when using α-BDDA as collector was less than 5% and when using DIDA as collector was less than 1%. For the mixed collector DPA-BDDA, the recovery of spodumene and feldspar was 82.27% and 32.61% respectively at pH 4.5. For mixed collector DPA-DIDA, the recovery of spodumene and feldspar was 35.69% and 9.08% respectively at pH 5.8. The results indicated that the cationic collector had high collecting capacity, but low selectivity. The collecting capacity of anionic collector for spodumene and feldspar was poor at the same concentration compared with cationic collectors. Mixed collector DPA-BDDA showed good flotation behaviour and selectivity on spodumene. The ―COO- in mixed collector might improve the selectivity. However, too much ―COO- would increase the electrostatic repulsion, which might cause low selectively and poor recovery. Keywords: Spodumene, feldspar, surface chemistry features, mixed collector, flotation

Jan 1, 2020

By J. V. Emmons

It has long been known that the outside skin of tool steel frequently exhibits properties widely different from the interior of the mass.

Jan 1, 1915

By A. Mertzanis

The way and methods used for the surface mining of bauxite until the end of the twentieth century in the area of Ghiona, resulted in a significant burden to the natural environment, especially in the cases where it covered extended parts of forests and forest areas as well as important geomorphological formations. The impacts from the surface mining of bauxite which in fact constitute the object of this study relate mainly to the interruption of the natural continuity of the land relief and the alteration of the natural geomorphological activities and are due to: a) the alternating excavations with fronts of great heights, b) the depositions of large volumes of waste materials which originate from the revealing of the ore and c) the dense road network constructed in order to get access to the mine locations.

Jan 1, 2006

(This paper reviews the reasons for and the principles followed in designing and constructing complete new surface works at the mine of the Zinc Corporation Limited, Broken Hill, New South Wales, and describes the layout, plant, buildings and services.)The Zinc Corporation mine produces high grade lead, silver and zinc sulphide ore. Lead and zinc concentrates are sent by rail to Port Pirie, where the lead is smelted and the zinc concentrate is shipped to Tasmania, England and other overseas countries.Some time ago consideration was given to the advisability of sinking an additional shaft. For some years the old main shaft had been working at full capacity and developments underground had indicated that the mine would eventually be capable of an output greater than that which could be handled through the shaft. It was therefore decided to sink a new main shaft and the site chosen was in footwall country 900 feet south of the old main shaft. The reason for the move south was so that the new shaft would be opposite the centre of gravity of the ore-bodies at depth. The size of the new shaft is 27 ft. ,6 in. x 15 ft., and the work was put in hand early in 1936.It was intended to haul the whole mine output through this shaft, which was 1,600 feet from the mill then operating. An extensive conveyor system thus became necessary unless a new mill was built near the shaft. A careful study of the situation was made by the management and consideration was given to requirements for expansion, the condition of...

Jan 1, 1940

By J. Starwood

Post-super-cycle mining executives must exploit every aspect of the value chain to deliver continued value to stakeholders. Integrating enterprise-wide information technology with value-chain-wide operational technology, known as IT-OT integration, is essential to extracting optimal results from the value chain. Mining companies trail other industries with respect to IT-OT integration across the value chain. Manual data consolidation and value chain optimization using spreadsheets and human intelligence are widespread practices within the industry. Increasing automation with smart devices and controllers means the volume and velocity of data will soon increase beyond human abilities. Enterprise Architecture provides a method for aligning information technology with the business operating model to successfully implement IT-OT integration. A Value Realization Framework (VRF) provides a means for predictable traceable value realization from IT investments and assets. With these principles, frameworks, models, methods, and techniques, mining organizations can accomplish IT-OT integration that provides their executives with a strategic value-chain-aligned platform for sustained value realization over the long term.

Feb 23, 2014

By J. L. Jernegan

IN a former paper laid before the Institute, entitled Lead and Silver Smelting in Chicago, I endeavored to give a description of the manner in which argentiferous lead ores from the far West were treated in that city, and also described the method employed in the desilverization of the silver-lead produced from the ores. It will perhaps be remembered, that very siliceous ores, principally from the Emma mine, Utah, containing over 40 per cent. of silicic acid, were then being treated at the works of the Chicago Silver Smelting and Refining Company in the reverberatory furnace, with the use of metallic iron, in the form of borings, as a precipitating medium for the lead ; and that the extraction of the silver from the resulting bullion was effected by the Balbach process. The Swansea Works, also the works at Brighton, just outside of this city, and those of S. P. Lunt, were at that time treating ore of a similar character by the same method. The inadequacy of the process for the ores then under treatment was, in a manner, pointed out by me in the paper above referred to. Since the time of its writing, many and important improvements have been made in the metallurgical treatment of Western ores in Chicago. Most ores are now roasted previous to reduction, and the latter operation is conducted in the shaft-furnace instead of the reverberatory. Such is the fact at least at the Swansea Works, the largest in the city, and here it was where the first steps were taken in this direction. In selecting these works as the subject of this paper, I am in hopes that the description given of the various metallurgical operations, as they are there now conducted, will serve to give an idea of the improvements introduced

Jan 1, 1876

By T. L. McCall

A short description of mining practice in the Sydney coal field in general is followed by a discussion of the operations in the No. 12 colliery of the Dominion Coal Company, Limited, as being typical of the trend in operating methods obtaining throughout the field. Development of longwall mining to the present system of three walls in line is outlined, together with a summary of the cycle of operations involved in systematic operation.

Jan 1, 1944

By F. W. Gray

A GEOLOGICAL study seeking to determine, for economic purposes, the value of the Sydney coalfield as a source of coal supply. Limitations of the coalfield come under two main heads: (a) Areal extent of the undersea coalfield. (b) The distance from shore at which coal can be mined at a cost of production permitting its profitable sale. Conclusions reached are that the areal extent of seams below the Phalen seam is of. small economic importance, and that non-persistence of these seams in full thickness and quality in the undersea extension of the coalfield will put an end to profitable mining before any limitations connected with distance from the shore-line become operative. With respect to the Phalen seam, non-persistence or deterioration of the seam will become effective in the western part of the coalfield, and less certainly in the eastern part of the coalfield, before operation of limitations by distance from shore. In the central portion of the coalfield, the seam probably persists in commercially workable thickness and quality to beyond the limit of mining set by distance from the shore-line. With respect to the seams above the Phalen seam between the Mountain fault on the extreme western boundary of the coalfield and the assumed termination of the deposition area on the eastern extremity of the field near South Head of Morien, there appear to be only such limitations as arise from engineering approach, distance from shore, sufficiency of strata cover between the sea-floor and the upper coal seams, and quality of the coal (with certain reservations as to the continuity of the upper seams under Sydney harbour and in the Sydney Mines-Little Bras d'Or district). Some of these seams have fragmentary land outcroppings from which their persistence seaward is assumed, and there may be other and still higher seams in the strata column which are entirely submarine.

Jan 1, 1941

Whilst much has been written in past years by geologists, scientists, mining engineers, etc., regarding the well·known and justly notorious anticlinal, or, as they are more commonly known, " saddle" reefs of Bendigo, comparatively little noticehas been given to the synclinal or "inverted saddle "reefs and their relationship with each other. In taking up the question of the synclinal folds, I recognise that it is a large undertaking to confine within the limits of a short paper, and at the same time convey a comprehensive idea of their characteristics, and the importance of their relationship with the anticlinal folds, in the general question of practical mining. However, from a practical point of view I consider the question of great importance, and if an interest in it can be awakened, more particularly among practical men, the object of this paper will be achieved.Before entering into the subject I must briefly state some facts, and perhaps some theories, in respect to the deposition of the Lower Silurian rocks, and their subsequent buckling up, as now seen on the Bendigo gold-field. At the same time, I do not intend to go very closely into the geological aspect of the question, as I wish the paper to be considered as a practical one.

Jan 1, 1902

By D Pienaar, B McFadzean, C T. O’Connor

Collector and frother molecules in sulfide mineral flotation are thought to have separate roles in the flotation process, where the collector selectively hydrophobizes the mineral surface and the frother adsorbs onto the bubble surface, inhibiting bubble coalescence. Molecular interactions have been observed between these molecules which allow them to co-adsorb at each of the respective interfaces, improving pulp phase recovery. This study investigated the molecular interactions between sodium diethyl dithiophosphate (SDEDTP) and hexanol, and the mechanism by which these interactions improve the recovery of galena. In this study each of the respective interfaces were investigated for the adsorption of SDEDTP. The adsorption of SDEDTP on galena was measured by UV-Vis spectrophotometry and isothermal titration calorimetry. At the air-water interface foam stability and pulp bubble coalescence was used to quantitatively discern if there are interactions between SDEDTP and hexanol. Microflotation and induction time experiments were performed to determine the effect of SDEDTP, hexanol and their mixtures on mineral recovery and bubble-particle attachment. The results of all these tests were collated to determine if SDEDTP-hexanol mixtures synergistically improve sulfide mineral recovery. It was found that SDEDTP reduced bubble coalescence in the pulp demonstrating activity at the airwater interface. Together SDEDTP and hexanol synergistically enhanced foam stability. This indicated that there are attractive molecular interactions between these reagents. Even though DTP did not adsorb onto galena, DTP-frother mixtures synergistically improved the recovery and attachment probability of this mineral. Adsorption studies with aeration showed that DTP in the presence of a frother transfers from the air-water interface to the galena mineral-water interface during bubble-particle collision. It was proposed that the transfer of hexanol through the thin film enhanced the kinetics of film thinning between the bubble and the particle by destabilising the thin film thus improving pulp phase mineral recovery.

Aug 24, 2022

By Bas R. Hemmen

GeoBrain is a facility at GeoDelft with the purpose to provide society with all relevant geo-engineering knowledge and experience in a structured way. On the basis of the available knowledge and experience engineers, decision makers and construction supervisors can come to a fast, reproducible and objective choice, taking into account the consequences. The paper presents examples from the GeoBrain experience databases and forecasting models developed for foundation engineering and directional drilling, or: "GeoBrain Foundations" and "GeoBrain Drilling". GeoBrain is closing the gap between theory and practice. It is aimed directly at reducing uncertainty and the costs of failure, thereby increasing the quality of profession and minimising the risk in geo-engineering works.

Jan 1, 2006