Search Documents

By S. Stone

Because of problems encountered with conventional timber supports, a system of concrete sausageshaped support pillars was tested. The pillars are 3 m long, 0,6 m wide, and between 70 and 80 cm high (the height of the stoping width). They consist of bags filled with a grout of cement (slagment and sand in the ratio of I :2, and are installed in a staggered pattern 6 m apart on dip and 2 m apart on strike. These support packs have proved successful, and, although they cost more than the timber supports formerly used (R4,63 per cent are supported as against R2,26 for the conventional timber pack), their use is felt to be justified when account is taken of the costs of lost production and low productivity due to the bad hangingwall conditions that occurred with the conventional system.

Jan 1, 1978

By Hargraves A. J

The paper outlines events at the Collinsville State Coal Mine, Queensland, leading to the practice of full face multiple shotfiring in bord and pillar development places. The 1954 disaster is referred to, and factors involved in simultaneous shotfiring in coal are discussed. Promising preliminary multiple shotfiring tests at the Colliery are described, as well as the resulting routine measures adopted, and the changes involved. The subsequent inducing of two outbursts under safe conditions by remote multiple shotfiring is given as justification for the changes made.INTRODUCTIONFollowing a disastrous instantaneous outburst (1.0.) of coal and gas at the Collinsville State Coal Mine in 1954, the necessity for inducer shotfiring for the control of possible further outbursts was established. However this mine, immediately classified as gassy after the 1954 outburst, is subject to the general restrictions pertaining to gassy mines which at present preclude the use of inducer shotfiring due particularly to the non-existence of a permitted exploder for more than six shots, and further, because permitted multipleexploders are not designed for remote firing through long lengths of cable. This situation was met by arresting or reducing progress in the production places, thereby reducing the danger of outbursts while means were being considered to achieve overall maximum safety.In August 1957 two full faces were successfully blasted in experimental simultaneous rounds. In June 1958 four full faces were blasted, and in October 1958 full face grunching without prior cutting, Le. inducer shotfiring, was introduced in No. 1 Tunnel as a production feature. In March 1960 it...

Jan 1, 1960

By Christopher Mark

Perhaps the most significant development in coal mine ground control during the last century was the introduction of roof bolting during the late 1940’s and 1950’s. From an engineering standpoint, roof bolts are inherently more effective than the wood timbers they replaced. Roof bolts promised to dramatically reduce the number of roof fall accidents, which then claimed hundreds of lives each year, and they were initially hailed as “one of the great social advances of our time.” Roof bolting also emerged at a time of rapid technologic transformation of the coal industry, and greatly accelerated the transition to trackless, rubber-tired face haulage. The U.S. Bureau of Mines quickly became the new roof support’s strongest advocate. Some state agencies and miners were skeptical at first, but nearly everyone was soon won over. Case histories were reported showing that roof falls could be largely eliminated while productivity increased dramatically. Little wonder that, in the words of one contemporary observer, “roof bolting has been adopted more rapidly than any other new technology in the history of coal mine mechanization.” Yet by the end of the 1950’s, it was clear that roof fall fatality incidence rates had actually increased. It would be another decade before the superior ground support provided by roof bolts would clearly save lives. The story of how roof bolting was implemented by the mining industry, but took so long to live up to its promise, is a fascinating example of the interaction between economics, technology, regulation, and science. It still has important lessons for today.

By Chris Mark

Perhaps the most significant development in coal mine ground control during the last century was the introduction of roof bolting during the late 1940's and 1950's. From an engineering standpoint, roof bolts are inherently more effective than the wood timbers they replaced. Roof bolts promised to dramatically reduce the number of roof fall accidents, which then claimed hundreds of lives each year, and they were initially hailed as "one of the great social advances of our time." Roof bolting also emerged at a time of rapid technologic transformation of the coal industry, and greatly accelerated the transition to trackless, rubber-tired face haulage. The U.S. Bureau of Mines quickly became the new roof support's strongest advocate. Some state agencies and miners were skeptical at first, but nearly everyone was soon won over. Case histories were reported showing that roof falls could be largely eliminated while productivity increased dramatically. Little wonder that, in the words of one contemporary observer, "roof bolting has been adopted more rapidly than any other new technology in the history of coal mine mechanization." Yet by the end of the 1950's, it was clear that roof fall fatality incidence rates had actually increased. It would be another decade before the superior ground support provided by roof bolts would clearly save lives, The story of how roof bolting was implemented by the mining industry, but took so long to live up to its promise, is a fascinating example of the interaction between economics, technology, regulation, and science. It still has important lessons for today.

Jan 1, 2002

By G. Daws, N. Woodward, A. Oxley

Many mines around the world have been seeking ways to achieve sustainable developments and reduce operating costs. Rockbolting is a technology that needs to be considered as it provides a means of reducing operating costs and improving safety whilst allowing improved production to be achieved. The problem is how to introduce this technology in the knowledge that a successful outcome will be achieved. Rockbolting is a complete package and not only includes the consumable materials but also training, production of Codes of Practice, Monitoring Schemes, Refinement of Design and long term management of the systems. This paper explains the methods that have been applied for its successful introduction and discusses several case studies. It does not give fine detail but is intended to allow decision makers to gain a basic understanding of the method used to successfully introduce rockbolting to a mine.

Jan 1, 2011

This paper deals chiefly with the preliminary examination, when a decision has to be made as to whether a prospect has a chance of developing into a mine or not. At this stage it is important to have a fairly clear conception of what is expected of the prospect, andjust what type of mine is sought. Much money can be wasted testing a prospect suitable for a prospector or small syndicate, but which never looked like becoming a mine of sufficient size to interest a company. When undertaking an inspection, therefore, it is necessary to have a broad outline, at least, of the policy of the principals for whom the report is intended.At this early stage it is frequently necessary to form an opinion of the prospects of a property on very meagre data. When new to this type of work one's first reaction is often th~t it is impossible to pass an opinion on the data available. It. is absolutely necessary,however, that an opinion of the possibilities and chances of favourable development be given; The report should strive to convey this information, making quite ::lear the risk involved, how complete are the data on which this opinion is based, and the possible magnitude of the prize. A Preliminary report has to state whether a property has sufficient prospects to warrant testing.The following procedure is suggested in order to make best use of the data and minimise hasty conclusions influenced by preconceived ideas-an ever-present danger.Examination.The first stage is the examination. This should aim at collecting all available significant data, but avoid clouding the issue with detail which, at this stage, will not affect the decision. The following points are considered to be the main ones for which to look:-Geological Environment.As good a working knowledge as possible'of the geology of the area should be obtained. Government Geological Survey reports and maps, if available, will be a big help. A detailed knowledge of the regional geology is not necessary a,t this stage, but a broad outline of the geological setting of the prospect under review, and also of any other important mines in the district, is often helpful in the final decision.The Nature of the Ore-Body.Any facts concerning the nature or occurrence of the lode should be noted as, coupled with experience of similar bodies, they affect the ultimate decision.Structural Control.This is probably the most important factor, in the light of present geological knowledge. Its chief importance is due to two facts:-(a) Structure plays one of the prime parts in ore deposition.(b) Geological knowledge, of structure is somewhat in advance of knowledge of other factors influencing ore deposition.

Jan 1, 1950

By Jingzhong Kuang, Zheyu Huang, Chuanzhou Guo, Pengfei Liu

"In this paper, scheelite and scheelite coated with Pb2+ (SC) were synthesized by chemical precipitation with the help of ultrasonic. The role of the Pb2+ on scheelite was evaluated. Additionally, the dissolution behavior of minerals and the adsorption mechanism of collectors were investigated systematically via SEM, XRD, EDS. The results indicate that the ultrasonic cavitation can promote the formation of scheelite with large particle size and high crystallinity. Due to the exchange of WO4 2- and OH-, the dissolution of scheelite are not in a 1:1 equivalent amount by chemical formula and the concentration of WO4 2- is higher than that of Ca2+ in the solution because Pb2+ promotes the transfer of WO4 2- from scheelite surface into the solution. The dissolution of scheelite is an endothermic reaction and its enthalpy reaches the maximum value of 692.59J·mol-1 at pH=8~10. But the coating of Pb2+ changes the thermal effect of scheelite in the solution and the dissolution of SC is an exothermic reaction with the dissolution enthalpy of -262.30 J·mol-1. At pH=8~10, the adsorption capacity of sodium oleate and salicylhydroxamic acid on the surface of SC is higher than that of scheelite which delivers that Pb2+ contributes to the scheelite surface dissolution and enhances the adsorption of collectors on the mineral surface, thus achieving activation.INTRODUCTIONIn modern society, tungsten is a type of quite important rare metal and also a strategic resource. Because of its low vapor pressure, high melting point, good electrical and thermal conductivity properties, it is widely applied in high-temperature technology, lighting, machine and engine construction (Zhao,Z.W, 2013; Yan, W, 2017; Ilhan, S, 2013). Both scheelite and wolframite are the major tungsten deposits. With the depletion of easily-processed wolframite, scheelite has drawn a great deal of scientific and industrial attention. Scheelite can be recovered by flotation due to the metathesis of polarity and chargeability on minerals surface via adding regulators and collectors."

Jan 1, 2018

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Umit Ozer

The environmental problems such as vibration, and air blast are often faced, and discussed on mining, quarrying, civil constructions, shaft-tunnel, pipeline, and dam operations where blasting is inevitable. It is necessary to establish national standards towards to minimize the environmental problems induced by blasting and judicial matters in our country as it is in USA, EU countries and the other developed countries. This necessity and the obligatory of accepting the European Union criteria for Turkey that has started the procedure of joining to EU emphasize the importance of this study. In other words, the establishment of a particular national standard related with this subject is inevitable for Turkey. This will be possible only by studying, applying scientific methods and techniques by the experts.

Jan 1, 2010

By Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Mehmet Aksoy, Deniz Adiguzel

The environmental problems arising from ground vibration has been faced and discussed frequently in various industries such as quarry, mining, civil works, shaft, tunneling, pipe line and dam construction etc. where the blasting operations are unavoidable. In bench blast design, not only the technical and economical aspects, such as block size, uniformity and cost, but also the elimination of environmental problems resulting from ground vibration and air blast should be taken into consideration. The prediction of ground vibration components plays an important role in the minimization of the environmental complaints. This paper presents the results of ground vibration measurements carried out in the quarries located on the different sides of Çatalca district in Turkey. In order to predict peak particle velocity level for this district, ground vibration components were measured for shots during bench blasting at these quarries. In blasting operations; ANFO is commonly used as blasting agent at the quarries. The type of priming and firing differed from quarry to quarry. The parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events by using different type vibration monitors. The absolute distances between shot points and monitor stations were determined by using GPS. The equation of square root scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity. In order to predict, and compare the influence grades to the neighboring buildings, and structures at the Çatalca district, the particle velocities and frequency values of all blast events are evaluated according to the United States Bureau of Mines (USBM) and German DIN 4150 Norms due to the lack of a national standard in Turkey. Then, the data pairs belonging to these quarries were gathered together to represent the district and were analyzed statistically. At the end of statistical evaluation of the data pairs, an empirical relation which gives average line at 95% confidence level and upper bound 95% prediction line with a reasonable correlation coefficient was established between peak particle velocity and scaled distance

Jan 1, 2007

By Kuganathan K, Potvin Y

Enterprise Mine at Mount Isa is to expand ore production from the current 1.4 to 3.5 mtpa by mining the 3500 Orebody, from which production is scheduled to start in February 1998 making this the deepest underground mine in Australia with its lowest mining horizon at nearly 1.6 km below surface. The following fill requirements were defined for the 3500 Orebody during the feasibility study: 1. a minimum filling rate of 250 ma/h, 2. a curing time of 28 days, and 3. minimum free fill water. This paper mainly describes the investigation of high density and paste fills for the 3500 Orebody. The investigation covered all the key issues relating to fill option selection, including design criteria, material supply and demand assessment, drainage modelling, tailing dewatering method, mix design and a pump loop test. Results of the investigation indicate that both high density fill and paste fill are technically feasible. The investigation has led to the selection of a blended tailing paste for the 3500 Orebody as the paste option has significant advantages over high density fill in stope filling rates and fill reticulation. The blended tailing for paste fill is finer than Isa deslimed tailing but coarser than full plant tailing. The paste fill selected has minimum binder and tailing dewatering requirements while a relatively high filling rate is achieved.

Jan 1, 1998

By Jiongtian Liu, Guihong Han, Shuzhen Yang, Yanfang Huang

Binder, as a necessary functional material of electrode in lithium ion battery, has a vital influence on the electrochemical performance. The humics, coupled with polyacrylamide (PAM) and sodium carboxymethyl cellulose (CMC), were used as a water-soluble binder for LiFePO4 (LFP) cathode using in lithium ion battery. The techniques of cyclic voltammetry (CV) and galvanostatic charge-discharge were conducted to evaluate the performance of humics binder in LFP electrode. The reversible specific capacity of LFP (HA + PAM + CMC) electrode can reach to 142 mAh g−1 after 50th cycling (100 mAh g−1) on conditions of raw materials with 1 wt% PAM addition, humics and CMC with a mass ratio of 3:1 in binder, and the raw materials mixed in an interval order. Humics has the potential to be used as a novel, eco-friendly and high-efficient binder for lithium-ion battery.

Mar 1, 2018

By Garren Edwards, van der Westhuizen. Andre

"Due to the depletion of easily treated coarser ores, more mineralogically complex ores with smaller valuable mineral grain sizes are treated, the means to liberate these minerals lies in grinding finer (Partyka & Yan, 2007). Grinding to these fine sizes is energy intensive, and using standard ball mills are energy inefficient at these sizes (P80 < 75µm). Therefore, stirred mills are becoming increasingly prevalent in the mineral processing industry. In order to optimize these mills, the effects and mechanisms of the significant variables need to be understood. This paper investigates a laboratory scale vertical stirred mill (Deswik mill) in an ultra fine grinding application of a South African platinum ore. The operating variables that are considered are stirrer speed, media size, media filling, and slurry density. The resulting grinding efficiencies are considered in two ways. Firstly, a statistical model is fitted to identify the effect of the significant variables on grinding efficiency, and secondly, the grinding efficiencies are also considered in terms of a stress energy model to determine whether this can partly explain the grinding mechanism in this mill. A factorial design of experiments was used on three levels for each variable, such that only linear interactions, second order interactions and two variable interactions are included in the statistical model. The results show that tip speed, media size, percent solids and mill filling are all significant to the grind, at differing energy inputs in the grinding process. The interaction effects of these variables are also dependent on the energy inputs. The results also found that the Kwade stress energy model is applicable to this mill and can be very useful to find the most efficient operating conditions for this system. The most energy efficient operating conditions in terms of mill speed and media size were typically somewhat below the standard operating conditions and it is expected that this is most probably done in order to increase the grinding rate, but at the expense of sacrificing some grinding efficiency."

Jan 1, 2014

By V. Bondarenko

The forecasting of floating earth inrush into the working is to a great extent connected with the investigation of the rock mass stressed-deformed state around the working. The aim of such investigations is to estimate the carrier ability of the protective layer (which is stabilized by the physico-chemical mode of fixing) and to determine it&apos;s thickness, which is to be sufficient to present the floating earth inrush into the working. We consider the protective layer to have exhausted it&apos;s carrier ability if the rocks of this layer reached the overlimit phase of deformation and it&apos;s greater part (section), which adjoins the working. is destroyed up to the limit of the remaining strength. So, the aim of investigations is to determine the size of the rocks inelastic deformation zone in the roof of the working. It is necessary to take into account the presence of water saturated seam in the roof and the overlimit characteristics of the rocks, their ability to lower the carrier capacity up to the level of the remaining strength.

Jan 1, 1996

By Ali Yalçin

The study area is located in the NW of Uluborlu (Isparta). Massive limestones and alluvial deposits form the lithological units of the study area. The average thickness of the alluvium deposit consisting mainly of light brown - red colored and fine grained clastic sediments which derived from the limestone is about 10 meters. The aim of this study to investigate the uses of this alluvial sediments as tile - brick material. For this aim, disturbed and undisturbed samples have been taken from different depths in the alluvial deposits. Mineralogical compositions have been determined by XRD and major oxide contents by XRF. Laboratory experiments have been carried out to determine the technological properties of the samples. The selected major oxide contents of samples vary between A12O3 (24.6 - 24.12 wt %), CaO (0.76 - 4.27 wt %), Fe2O3 (10.21 - 10.29 wt %), MgO2 (1.25 - 1.51 wt %). CaCO3 and MgCO3 values calculated from the geochemical analyses, are between 1.55 - 1.62 and 2.62 - 3.17 respectively. The ratios of grain size of the samples are 82 % for < 0.2 mm and 5 % for > 3 mm. Geochemical analyses and technological features of the samples indicate that these fine grained sediments of alluvial deposit are suitable in terms of uses as tile - brick material. The potential reserve of this tile - brick material has been determined as 40 million tones.

Jan 1, 2005

By Y. Tang

The paper studied the extraction characteristics of the fly ash from a location in Guizhou province. Under ordinary pressure, the fly ash is extracted by an acid and alkali, and then studied for its reaction characteristics with different extraction agentia, temperature, consistence and time. The results of acid extraction show that there are good reaction characteristics for Fe2O3 with HCl and the extraction rate decreases with the increasing of extraction time. There are good selective characteristics between Al2O3 and H2SO4 and they weaken with the increasing of temperature and the expanding of time. The best extraction results are shown with CaO and MgO because of their chemical characteristics and the over-saturation degree of the extraction processing. In addition, It?s found that it cannot leach all the substances from fly ash even with the higher consistence (10mol/L) of extraction agent, the longer extraction time (2h) and the higher temperature (100?) .It shows that the extraction rate of Fe2O3 is 82.81% and that of Al2O3 is 29.01%. The results of alkali extraction show that the extraction rate increases with the consistence of extraction agent and temperature, and the extraction rate of SiO2 by NaOH increases rapidly with the time expanding while that of Al2O3 falls gradually.

Jan 1, 2014

By IPMI Educational and Scientific Foundation

It is with great pleasure that we announce the availability of this fourth issue of the IPMI Journal, a publication of the International Precious Metals Educational and Scientific Foundation. This digital peer reviewed publication has been created as a vehicle for the sharing of technical information related to the science and technology of precious metals. Since 1976, the International Precious Metals Institute has championed the exchange of information of critical importance to the precious metals scientific and commercial communities through its various communications vehicles. This has included instructional videos, annual conference symposia, special topic committee meetings, regional seminars, and professional and student achievement awards. Due to the breadth of important topics related to all aspects of precious metals, it has been the vision of the IPMI to provide a publication available to the general public that would become a key source of pertinent topics containing high quality publications by experts in their fields of study. Historically, the IPMI has attracted world renowned experts in many fields (including Nobel Laureates Henry Taube, Ei-ishi Negishi, Robert Grubs, Professor Ben Feringa, and David MacMillan) in the dissemination of discoveries, inventions, and industry proven practices. Such information has a total value greater than the sum of its parts as seemingly unrelated innovations from distinct focus areas can be adapted to solve problems. Because of this important characteristic of information exchange, we have decided to create a digital journal, available to the general public, that will not only communicate state of the art discoveries and sound practices, but will also review historical communications from the IPMI’s archives that have value and use even in today’s environment. On behalf of the members and leaders of the IPMI, we hope you will find value in this new publication.

Dec 1, 2020

By IPMI Educational and Scientific Foundation

It is with great pleasure that we announce the availability of this fourth issue of the IPMI Journal, a publication of the International Precious Metals Educational and Scientific Foundation. This digital peer reviewed publication has been created as a vehicle for the sharing of technical information related to the science and technology of precious metals. Since 1976, the International Precious Metals Institute has championed the exchange of information of critical importance to the precious metals scientific and commercial communities through its various communications vehicles. This has included instructional videos, annual conference symposia, special topic committee meetings, regional seminars, and professional and student achievement awards. Due to the breadth of important topics related to all aspects of precious metals, it has been the vision of the IPMI to provide a publication available to the general public that would become a key source of pertinent topics containing high quality publications by experts in their fields of study. Historically, the IPMI has attracted world renowned experts in many fields (including Nobel Laureates Henry Taube, Ei-ishi Negishi, Robert Grubs, Professor Ben Feringa, and David MacMillan) in the dissemination of discoveries, inventions, and industry proven practices. Such information has a total value greater than the sum of its parts as seemingly unrelated innovations from distinct focus areas can be adapted to solve problems. Because of this important characteristic of information exchange, we have decided to create a digital journal, available to the general public, that will not only communicate state of the art discoveries and sound practices, but will also review historical communications from the IPMI’s archives that have value and use even in today’s environment. On behalf of the members and leaders of the IPMI, we hope you will find value in this new publication.

Dec 1, 2021

By IPMI Educational and Scientific Foundation

It is with great pleasure that we announce the availability of this fourth issue of the IPMI Journal, a publication of the International Precious Metals Educational and Scientific Foundation. This digital peer reviewed publication has been created as a vehicle for the sharing of technical information related to the science and technology of precious metals. Since 1976, the International Precious Metals Institute has championed the exchange of information of critical importance to the precious metals scientific and commercial communities through its various communications vehicles. This has included instructional videos, annual conference symposia, special topic committee meetings, regional seminars, and professional and student achievement awards. Due to the breadth of important topics related to all aspects of precious metals, it has been the vision of the IPMI to provide a publication available to the general public that would become a key source of pertinent topics containing high quality publications by experts in their fields of study. Historically, the IPMI has attracted world renowned experts in many fields (including Nobel Laureates Henry Taube, Ei-ishi Negishi, Robert Grubs, Professor Ben Feringa, and David MacMillan) in the dissemination of discoveries, inventions, and industry proven practices. Such information has a total value greater than the sum of its parts as seemingly unrelated innovations from distinct focus areas can be adapted to solve problems. Because of this important characteristic of information exchange, we have decided to create a digital journal, available to the general public, that will not only communicate state of the art discoveries and sound practices, but will also review historical communications from the IPMI’s archives that have value and use even in today’s environment. On behalf of the members and leaders of the IPMI, we hope you will find value in this new publication.

Dec 1, 2022

By IPMI Educational and Scientific Foundation

It is with great pleasure that we announce the availability of this fourth issue of the IPMI Journal, a publication of the International Precious Metals Educational and Scientific Foundation. This digital peer reviewed publication has been created as a vehicle for the sharing of technical information related to the science and technology of precious metals. Since 1976, the International Precious Metals Institute has championed the exchange of information of critical importance to the precious metals scientific and commercial communities through its various communications vehicles. This has included instructional videos, annual conference symposia, special topic committee meetings, regional seminars, and professional and student achievement awards. Due to the breadth of important topics related to all aspects of precious metals, it has been the vision of the IPMI to provide a publication available to the general public that would become a key source of pertinent topics containing high quality publications by experts in their fields of study. Historically, the IPMI has attracted world renowned experts in many fields (including Nobel Laureates Henry Taube, Ei-ishi Negishi, Robert Grubs, Professor Ben Feringa, and David MacMillan) in the dissemination of discoveries, inventions, and industry proven practices. Such information has a total value greater than the sum of its parts as seemingly unrelated innovations from distinct focus areas can be adapted to solve problems. Because of this important characteristic of information exchange, we have decided to create a digital journal, available to the general public, that will not only communicate state of the art discoveries and sound practices, but will also review historical communications from the IPMI’s archives that have value and use even in today’s environment. On behalf of the members and leaders of the IPMI, we hope you will find value in this new publication.

Dec 1, 2023

By IPMI Educational and Scientific Foundation

It is with great pleasure that we announce the availability of this fifth issue of the IPMI Journal, a publication of the International Precious Metals Educational and Scientific Foundation. This digital peer reviewed publication has been created as a vehicle for the sharing of technical information related to the science and technology of precious metals. Since 1976, the International Precious Metals Institute has championed the exchange of information of critical importance to the precious metals scientific and commercial communities through its various communications vehicles. This has included instructional videos, annual conference symposia, special topic committee meetings, regional seminars, and professional and student achievement awards. Due to the breadth of important topics related to all aspects of precious metals, it has been the vision of the IPMI to provide a publication available to the general public that would become a key source of pertinent topics containing high quality publications by experts in their fields of study. Historically, the IPMI has attracted world renowned experts in many fields (including Nobel Laureates Henry Taube, Ei-ishi Negishi, Robert Grubs, Professor Ben Feringa, and David MacMillan) in the dissemination of discoveries, inventions, and industry proven practices. Such information has a total value greater than the sum of its parts as seemingly unrelated innovations from distinct focus areas can be adapted to solve problems. Because of this important characteristic of information exchange, we have decided to create a digital journal, available to the general public, that will not only communicate state of the art discoveries and sound practices, but will also review historical communications from the IPMI’s archives that have value and use even in today’s environment.

Dec 1, 2024