Search Documents

By Madgwick J. C

Leaching column techniques and microbiological methods have been described in detail in Madgwick and Ralph (1980) and Madgwick, Ralph and Sadler (1981).Sixty-nine kilograms of copper porphyry ore (0.4 per cent Cu, 2.7 per cent Fe) (particle size 2.4-11.2 mm; 60 The effect of sodium chloride (O.6M) irrigation on bacterial leaching of Bougainville copper porphyry ore was studied.Viability of suspended Thiobacillus ferrooxidants was reduced to less than 10 cells/ml in NaCI (O.6M) compared with 10' eells/ml in dilute II,SO, (0.01 M, pll 2). Salt irrigation had no significant effect on heterotrophic and sulphur oxidizing bacteria. Increascd short term recovery of copper (145 g/tonne/ 15 days) was followed by a marked decrease in tenors to less than 20 mg/litre/day compared with an acid leach, steady release, of 110 mg/litre/day. Resumption of acid leaching restored average solution copper to 46 mg/litre/day and the viability of suspended T Ierrooxidates to 10 cells/ml.Quantitative removal of sodium ehloride from ore particles was difficult and t races of NaCI remained for more than 200 days.

Jan 1, 1982

By K. G. Matshika

"Nickel electroplating from sulphate electrolyte is an efficient process. To achieve good quality cathode, however, parameters such as temperature, nickel concentration, pH, electrode alignment, electrolyte flowrate and additives must be optimised, because these affect cathode morphology and current efficiency. It is also important to control the clarity and contamination of the electrolyte, as these have a considerable effect on the quality of the cathode surface. Delamination, surface roughness and pitting on the cathode surface can be caused by incorporation of solid particles or impurities form the electrolyte. Three types of solid particles were investigated: cuprous selenide, barium/ lead sulphate (co-precipitated) and ferric hydroxide. These particles can be found in industrial electrolytes, especially if there is a problem with the filtration step or contaminants have reacted to form insoluble particles. A rotating cylinder Hull cell was used for this investigation. It is found that the effects on morphology depend on the type of solid, concentration, particle size, current density and electrolyte flowrate. Cuprous selenide is the most detrimental, especially at higher concentrations, higher current densities and low flowrates. Increased rotational speed offers a uniform sheet of fine gas bubbles across the surface of the cathode which reduces the thickness of the diffusion layer of liquid adjacent to the cathode and increases the rate of mass transport to the cathode from the bulk liquid. INTRODUCTION Electrowinning operations are important when recovering associated by-products of nickel production, such as copper, cobalt and zinc, from pressure leach solutions. The base metal mineralization associated with platinum-group metal (PGM) production yields significant quantities of copper and nickel as by-products. The base metal refinery is vital in PGM processing as it increases the PGM concentration from mined ore by a factor of 400, in comparison with concentration by flotation (20 times) and pyrometallurgical processing (20 times) (Crundwell et al., 2011). Anglo American Platinum Ltd produces nickel cathodes by electrowinning and purges sodium from the base metal refinery in the form of sodium sulphate at the Rustenburg Base Metals Refinery (RBMR), as shown in Figure 1. This is the Sherritt acid leach process used in most base metal refineries to ensure no loss of PGMs and shows the subsequent purification steps for copper and nickel. Other refineries in Zimbabwe, such as Bindura and Empress, use the Outokumpu leach process (Pavlides, 2001)."

Jan 1, 2015

By Helmut Thielsch

IN recent years an ever increasing amount of interest has been directed toward research studying the principles and various applications of sonic and supersonic waves. Though still in their early stages of practical development, sonic vibrations are already used in the emulsification and degasification of liquids. Metals exposed to sonic or ultrasonic vibrations while solidifying show a considerable amount of grain refinement. Often sound waves are applied instead of radiography to test engineering materials for internal cracks and flaws.1 In the field of pure research these waves are used in dispersion and also in coagulation of particles or liquids in gaseous or, under certain conditions, in other liquid systems. In the settling and thickening of slurries considerable time is necessary to compress the solid particles and to squeeze out the liquid to obtain as low a dilution (liquid to solid ratio) as possible. Various methods have been developed to increase the amount of coagulation of the very fine solids (colloidal or semicolloidal) and to shorten the over-all time. The addition of small amounts of electrolytes and the warming of the suspension represent merely the more important techniques. Some of the effects of supersonic vibrations have been reported previously.2,6 From preliminary studies, therefore, it was hoped that by application of sonic vibrations it would be possible to reduce the time required to thicken such materials to a specific dilution, as well as to thicken to lower ultimate dilutions than could be obtained by quiescent settling alone. By increasing the volume thickened per unit time-i.e., improving the plant efficiency-great savings in equipment and time would be obtained for industrial processes. Also, faster settling rates should result if coagulation of particles could be increased. Experiments have been conducted for a period of several months in the Allis-Chalmers laboratory to study the effect of sonic vibrations on settling of particles of different sizes and concentrations. APPARATUS The sedimentation apparatus used in these experiments is illustrated in Figs. I and 2. The essential features are the stationary field coil and the movable voice coil. Both windings are placed around a solid iron core. A leather diaphragm connected to the steel frame holds the voice coil in place. A brass rod is fastened to the voice coil with a metal disk connected to the other end. This disk is sealed to the lucite cylinder with a flexible rubber diaphragm. The lucite tube is 17 in. long; its inner diameter is 2 ½in. and the wall thickness is ¼ in. The tube is calibrated on the outside in 10 c.c. divisions for a total of 1000 cubic centimeters.

Jan 1, 1946

By Stephen C. Tadolini, Yunqing Zhang, Thomas M. Barczak

Standing crib supports have been applied in underground mining programs to resist large roof movements and sustain high-loads. The strength and deformation capability of these systems has been documented under both laboratory and field conditions. The parameter that has not been examined and is not well understood is the effect that a crib or other types of standing support has on the primary and secondary bolting systems. A crib support system with low system stiffness may allow large amounts of closure and deformation and cause the bolting systems to yield or even fail. Conversely, cribs or standing support that are too stiff may experience brittle or buckling failures, negating the advantage of the intrinsic supports previously installed. Utilizing a combination of field measurements and 3-dimensional finite element modeling techniques, the relationship between system stiffness and the subsequent performance of the installed bolting system is evaluated. Additionally, a simple method for calculating the combined system stiffness for standing supports, when using materials with different strengths such as steel, concrete, wood, etc., is presented.

By Stephen Tadolini

Standing crib supports have been applied in underground mining programs to resist large roof movements and sustain high¬loads. The strength and deformation capability of these systems has been documented under both laboratory and field conditions. The parameter that has not been examined and is not well understood is the effect that a crib or other types of standing support has on the primary and secondary bolting systems. A crib support system with low system stiffness may allow large amounts of closure and deformation and cause the bolting systems to yield or even fail. Conversely, cribs or standing support that are too stiff may experience brittle or buckling failures, negating the advantage of the intrinsic supports previously installed. Utilizing a combination of field measurements and 3-dimensional finite element modeling techniques, the relationship between system stiffness and the subsequent performance of the installed bolting system is evaluated. Additionally, a simple method for calculating the combined system stiffness for standing supports, when using materials with different strengths such as steel, concrete, wood, etc., is presented.

Jan 1, 2003

By G. Mousavian, R. Bagheri, N. Dalili

Polypropylene (PP) and its composites have an increasing use in automobile and domestic industries. Since the published results on strain rate effect on yield behavior do not match, and there is a high attention paid for effect of nanometeric fillers on deformation behavior of composites, in this research the strain rate effect on yield behavior of PP and the effect of nanometeric fillers on deformation behavior of PP have been studied. Microscopic observations and tensile tests in different strain rates on neat PP samples and on samples filled with 5, 10 and 15 %wt have been used. A dramatic change in behavior for the modulus and post-yield slope curves when the strain rate is between 0.0433-0.05 s-1 has been observed. Microscopic observations on PP indicate a change in deformation mechanism from shear yield to crazing at the same strain rate that the change in behavior of curves occurs. It has been observed that in PP nanocomposites with higher amount of calcium carbonate, fracture in early stages of deformation occurs in lower strain rates. In other words for a fixed stain rate there is a critical filler percentage such that if the filler percentage is higher then early-stage fracture will occur. Similarly for a fixed filler percentage there is a critical strain rate and in higher strain rates early fracture will occur. The critical stain rate will decrease as the filler percentage increases and vice versa.

Jan 1, 2006

By S. S. Makgato

In this study, coke oven tar additions over a range of 0?8 wt.% were evaluated as a possible substitute for imported coal fractions. The coke oven tar used was collected from tar decanters in the byproducts section of the coking plant. The moisture content in the tar varied depending on the residence time and water carryover from the coke oven tar separators to the storage tanks. Moisture contents of 1 wt.%, 3 wt.%, and 6 wt.% were investigated in order to evaluate the effect on coal blend, carbonization, and coke properties. At 6 wt.% moisture content with 6 wt.% coke oven tar, although the coke quality improved the yield showed a 4% decrease. On the other hand, 1 wt.% moisture content with coke oven tar of 6 wt.%, increased the yield by 1% and the coke quality improved. However, the latter process was characterized by an excessive increase in wall pressure and pushing energy, both of which are detrimental to the oven walls. The optimum moisture content in coke oven tar was found to be 3 wt.% with a coke oven tar addition of 6 wt.% in the coal blend. With these conditions, the coke properties improved and wall pressure and pushing energy were acceptable. However, a decrease in coke yield of up to 2% was observed. Despite this, coke oven tar addition is considered to be a viable option based upon economic factors of a reduction in the quantity and cost of imported coking coals that is required to achieve the same optimum final coke product. Keywords coal substitution, coke oven tar, tar moisture, coal blend, coke, coke quality.

Nov 1, 2013

By Tumilty JA, Schmidt CG

Sulphide ion is a powerful poison in gold cyanidation, however, the detrimental effect is less severe in plant practice. This is thought to be due to the presence of depassivating elements in the ore, mainly lead. Trace amounts of lead can counteract the poisonous effect of considerable amounts of sulphide. The reaction is instantaneous and is likely to be a direct involvement in the electrochemical surface reaction. Lead addition cannot be regarded as an all-round cure when experiencing poor leach efficiencies. A possible beneficial effect depends on the mineralogy of the ore and has to be determined individually for every material.

Jan 1, 1989

By Ranklin W. J

The mechanism and rate-limiting step of carbonaceous reduction of zinc from slags was investigated in the laboratory. Disks of graphite were rotated in ZnO-containing slags at various speeds for fixed periods at 1250 to 1325¦C. The mass loss was used as a measure of the amount of ZnO reduced. Application of the Levich equation indicated that at rotation speeds at which it is valid, the reduction was chemically controlled with an activation energy of 27 kcal/mol. At zero rotation speed the reduction of ZnO by carbon appeared to be slag-phase mass transfer controlled with an activation energy of 38 kcal/mol. An increase in the FeO content of the slag increased the rate of reduction while an increase in sulphur content decreased the rate of reduction. When FeO was present in the slag, reduction appeared to occur by a combination of indirect reduction of ZnO by carbon and by reduction by FeO with reduction of Fe203 back to FeO by carbon. The effect of sulphur was consistent with a surface blockage mechanism due to the surface active nature of sulphur in slags.

Jan 1, 1993

The addition of copper sulfate to mineral slurries in order to ?activate? sulfide mineral surfaces for enhanced collector molecule adsorption, and hence enhanced recovery via flotation, is a com-mon mineral processing practice. It has been established in a laboratory situation that the addition of CuSO4 in conjunction with xanthate collector increases the flotation rate of pentlandite as compared to the addition of collector alone. However, it remains unclear whether the addition of CuSO4has a similar effect within mineral processing circuits. We examine here the effect of pre-activation oxidation on the copper activation of pentlandite and monoclinic and hexagonal pyrrhotite. All activation experiments were carried out at pH 9 using a total solution content of copper ions equivalent to one monolayer (0.210 -4 moles, 110-4M). Copper loss from solution was extremely rapid in all cases with less than 10 % remaining after 10s. EDTA extraction and solution analysis clearly demonstrated that copper activation was via direct surface adsorption and not an ion exchange process, as is the case for sphalerite, and that most copper on the surfaces is in the form of Cu(I). ToF-SIMS analyses of the mineral surfaces subsequent to copper activation show increased surface oxidation on increased conditioning time prior to copper activation. However, there is a significant decrease in surface oxidation on comparison of samples that have otherwise been prepared in the same manner but where one has been exposed to copper solution rather than water. This suggests that copper activation stabilises the surface and reduces the propensity for oxidation. Regardless of the length of pre-activation oxidation time only Fe(III) (no Fe(II)-S) was observed by XPS analysis, indicating a highly oxidised surface layer dominated by Fe-O-OH species. The presence of Cu(II) on the mineral surface is indicative of the formation of Cu(II)-containing precipitates and indicates non-mineral specific activation resulting in increased recovery but lower grade. Mineral specific copper adsorption, as evidenced by the presence of Cu(I), is required to improve both grade and recovery. Prolonged oxidation prior to copper activation causes a reduction in the Cu(I) to Cu(II) ratio on the mineral surfaces as compared to either fresh surfaces or surfaces oxidised for 1 minute only. This strongly indicates that the copper activation process is less effective on highly oxidised surfaces.

Jan 1, 2014

By J. Stachurski

Flotation tests were carried out on 6 coal samples of different rank as well as their oxidized samples. A mixture of diesel oil and alcohols was used in these tests. Surface oxidation caused a distinct decrease of the flotation recovery with some improvement in the grade The reduction in the recovery increased with increasing the concentration of the oxidizing agent. The floatability of low rank coals was affected by oxidation to a higher degree than medium and high rank coals. The recovery size curves of oxidized samples mere similar in shape to that of non-oxidized coals.

Jan 1, 1990

By J. D. T. Steyl

Anglo American Corporation and the University of British Columbia have developed a medium-temperature oxygen pressure leaching process for the extraction of copper from chalcopyrite concentrates in an acid-sulphate system (AAC/UBC process). Leaching is performed at 150°C and surfactants are added to disperse molten elemental sulphur from the unreacted sulphide surface to prevent liquid sulphur occlusion. Copper extractions of over 95% and elemental sulphur yields of around 60% were observed over a 2-hour average residence time in a continuous pilot autoclave. Sporadic blockages occurring under continuous conditions were found to be caused by the accumulation of molten elemental sulphur mixed with unreacted sulphide mineral. A batch programme of experimentation was undertaken to establish the reason for this phenomenon. Batch experiments were conducted at low pulp densities on concentrate samples with narrow size distributions and at similar solution compositions to those experienced in the pilot autoclave. The overall rate of chalcopyrite oxidation was shown, under approximately constant solution composition, to be a strong function of the total available mineral surface area. Initial copper extraction rates followed the shrinking particle kinetic model under intrinsic surface control. Deviation from shrinking particle kinetics was however observed after a certain oxidation time. Secondary electron images identified small (typically less than 20 µm) sulphur conglomerates at the point of deviation, which 'collected' unreacted chalcopyrite mineral particles and lowered the total mineral surface area available for oxidation. These sulphur clusters are thought to be the precursor for blockages experienced in the continuous pilot autoclave. These results emphasised the importance of fine grinding (P80 5-20 µm) and suggest that shorter residence times may minimise the formation of sulphur conglomerates in a continuous autoclave operating at medium temperature.

Jan 1, 2004

By Jamal Rostami, Tala Tahernia

TBM utilization rate is a component of machine performance prediction and critical for developing a reliable estimate of the construction completion time and cost of the tunnel. Estimation of the utilization rate involves identifying and quantifying the time dedicated to each activity in a tunneling jobsite. Ring building is a common activity in TBM tunneling and takes a large amount of tunnel excavation time when using shielded TBMs. This paper concentrates on the effect of tunnel diameter on the duration of downtimes related to ring building and examines the impact of machine diameter on downtimes. For this purpose, the dependency of segment installation time to segment configuration, and also the diameter of the tunnel was investigated. Furthermore, the ring building time for four tunnels with different sizes of diameters and a variety of ring arrangement were analyzed and the relationship between TBM diameter and segment installation time and consequently TBM utilization was evaluated.

Jun 13, 2021

By Qingguo Xue, Jingsong Wang, Guang Wang, Yuanyuan Zhang

Due to complicated structure and composition of high-phosphorus iron ore, pure substances were used to simulate the chemical composition of high-phosphorus iron ore to study the reaction of fluorapatite at different temperatures and effect of additives. The gasification process of P during carbothermic reduction process was investigated using a quadrupole mass spectrometer gas analysis. It is found fluorapatite was reduced to phosphorus which diffused into iron and gas phase. From the gas analysis, it was observed that PO and P gas species were vaporized around 800 °C. As the reduction temperature increased, the diffusion of phosphorus into iron was enhanced. The presence of Ca(OH)2 as additives not only promoted the reduction of iron oxide, but also decreased the degree of fluorapatite reaction to inhibit P into iron.

Mar 1, 2018

By Neill Bartie, Jacques Eksteen, Sharif Jahanshahi, Shouyi Sun

The gradual increase in Cr2O3 levels of UG-2 ores has become a matter of concern for platinum producers in South Africa due to the formation of chromite spinels in melters. The effect of bulk FeOx/MgO ratio, Cr2O3, temperature and oxygen partial pressure on phase stability and composition in the system FeOx-MgOSiO2- Cr2O3-Al2O3-CaO has been studied between 1400°C and 1600°C using the drop-quench technique. An increase in temperature was found to result in a decrease in [Fe/Cr]spinel. An increase in bulk FeOx/MgO caused Mg, Al and Cr in spinel to decrease, forming more magnetite relative to other spinels. [Fe]spinel decreased and [Cr]glass increased with a decrease in oxygen partial pressure.

Jan 1, 2003

By Jacques Eksteen, Sharif Jahanshahi, Neill J. Bartie, Shouyi Sun

The gradual increase in Cr2O3 levels of UG-2 ores has become a matter of concern for platinum producers in South Africa due to the formation of chromite spinels in melters. The effect of bulk FeOx/MgO ratio, Cr2O3, temperature and oxygen partial pressure on phase stability and composition in the system FeOx-MgO-SiO2-Cr2O3-Al2O3-CaO has been studied between 1400°C and 1600°C using the drop-quench technique. An increase in temperature was found to result in a decrease in [Fe/Cr]spinel. This effect is shown in Figure 1 for the six slag compositions investigated.

Jan 1, 2003

The addition of a thallous salt to the cyanide leach of a calcined pyritic concentrate causes a marked increase in the rate of extraction of gold. This is due probably to the activation of passive gold by the thallous ions. Lead, bismuth, and mercury salts, which should produce a similar effect, fail to do so. It is postulated that this latter result, together with the reprecipitation of silver at low cyanide levels, is due to the presence of soluble sulphide.INTRODUCTIONThe work of Fink and Putnam (1950) showed that the rate of solution of gold in cyanide can be increased by the addition of small amounts of lead, bismuth, mercury, and thallium salts. Mills (1951), during a study of the electrochemistry of gold, with particular reference to cyanidation, was able to show that gold may become passive towards cyanide solution. The addition of lead or thallium salts prevented this passivity, although the action of lead was limited to the pH range 10 to 12. In a recent paper Cathro (1963) confirmed the findings of Mills, and presented results which showed that the addition of thallium to a cyanide leach of a calcine from Lake View and Star mine, Kalgoorlie, increased the rate of extraction of gold appreciably. In, this paper the use of thallium to prevent the gold becoming passive, and hence to decrease leaching time and cyanide consumption, is examined.EXPERIMENTALA series of leaching tests was carried out on a sample of Lake View and Star calcine, comprising calcined pyrite (about 70 per cent.) and siliceous gangue (about 30 per cent.) and containing 165 p.p.m. gold, 45 p.p.m. silver, 0·1...

Jan 1, 1964

The addition of a thallous salt to the cyanide leach of a calcined pyritic concentrate causes a marked increase in the"rate of extraction of gold. This probably is due to the activation of passive gold by.th,e. thallous ions'.''Lea'd, bismuth, and mercury salts, which should produce ' a, similai effect, fail to do so. It is postulated that'this latter result, together with'the reprecipitation of silver at low cyanide levels, is due to the presence of soluble sulphide. The use of thallous salts to reduce leaching time is discussed briefly.

Jan 1, 1964

The mining industry continues to be a major driver of the Australian economy generating over A$130 billion in export earnings in 2008/2009. However, the industry has been cited as a significant contributor to green house gas emissions. Australia's proposed carbon trading scheme, the Carbon Pollution Reduction Scheme (CPRS) will financially impact on mining operations; this calls for a holistic planning approach for mining operations taking into account the impact of the emissions trading scheme. Since carbon trading is a new area of study, particularly within Australia, the quantitative effect of the CPRS on the mining industry is uncertain and current mine planning practices do not directly consider emissions. This paper presents results of the study into the impact of the CPRS on a hypothetical large scale open pit operation, using a spreadsheet model based on linear programming and simulation. By varying the production rates, life of mine (LOM), carbon price and ore grades among other variables several scenarios were simulated to determine the impact of emissions trading scheme on the net present value of the project. This study found that the adoption of the proposed Carbon Pollution Reduction Scheme could impact mining operations in Australia by a three per cent to six per cent reduction in net present value, for carbon credit costs of $25/t to $50/t respectively. While the six per cent reduction in net present value for a mining operation is significant, rising fuel prices have had a similar effect in recent years. The most energy-intensive processes are the milling circuit and the flotation concentrator circuit. These processes are jointly responsible for up to 60 per cent of the total emissions, depending on the production rate and the level of offshore processing conducted. Clearly, the introduction of the CPRS makes it is imperative for mining companies to assess the impact of carbon emissions on a mining project during mine planning.

Dec 6, 2010

By G. A. Slabbert

The paper describes work undertaken to identify the influence of the matrix structure on the metal dusting rate of stainless steel alloys. Specifically, the difference in metal dusting rate between austenitic and ferritic stainless steels of similar chromium contents was investigated. The alloys were exposed to metal dusting conditions and their performance compared by weight loss, optical microscopy, scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and Raman spectroscopy. The specific gas mixture used for all the tests were 18.9% CO-79.1% H2-2% H2O at 650°C. For austenitic stainless steels, Types 304, 321, 316, and 316Ti were compared to two ferritic grades, namely Types 430 and 441. The resistance of the ferritic grades was found to be significantly better than that of the austenitic grades. This was attributed to greater permeability of chromium through the matrix structure to maintain the protective oxide scale. The results will be used in the development of novel alloys to combat metal dusting.

Jan 1, 2013