Search Documents

By F. G. Miller

To improve coal flotation Bethlehem Steel Corporation's Research Department has been working on a number of related problems based on both physical and chemical factors. The ideal is of course full understanding of the interrelated effects of both sets of factors. However, detailed studies5 of each physical factor have produced immediately usable results in commercial coal flotation and are providing the bas is for our current work on the effect of chemical factors. Since these detailed studies provided the basis for the present investigation of froth sprinkling, their key results are highlighted here. For example, for a highly floatable bituminous coal, particle floatability was shown to be directly related to the percentage of coal surface available for bubble attachment and inversely related to particle mass. The data also underscored that in a given size range the addition of mineral matter to a particle makes flotation more difficult both by adding to the mass of the particle and by decreasing the amount of coal surface available for bubble attachment. Size also affects particle floatability in that as the size of particles of a given specific gravity increases, mass increases and the ratio between coal surface area and mass of the particle decreases. Flotation tests showed that any recovery of the coarsest particles in a coal feed is accompanied by progressively higher recovery of finer and finer particles. Consequently, fine high-specific-gravity particles are recovered with the coarse good coal. As a result, when the entire 14M x 0 size range is processed by froth flotation, the good coarse coal is contaminated with high-specific-gravity fines. It is the small quantities of these fines that must be rejected from the froth product if flotation efficiency is to be increased above its present level.

Jan 1, 1968

By F. Ngoroma

Concentrators processing PGM bearing ores make use of polysaccharide depressants to reduce the recovery of the undesired naturally floatable gangue minerals, mainly silicates, present in the ore. Recent work has shown that high depressant dosages can completely depress naturally floatable gangue and thus prevent it from reporting to the concentrate. These high depressant dosages can, however, have a negative effect on the recovery of valuable minerals present in the ore by reducing the stability of the froth. In order to counterbalance the effects of depressant addition, frothers are added. It is, however, preferable to maintain independent control over bubble size and froth stability which is difficult to achieve with only one frother. An alternative strategy is, to use a blend of frothers, e.g. a weaker frother in combination with a stronger frother. Such a system allows an additional degree of freedom: changing the ratio of the two frothers, that would provide more independent control of bubble size and froth stability. This study demonstrates, through the use of batch flotation tests, how blending low molecular weight alcohols with commercially available frothers impact the solids and water recovery, as well as the valuable mineral recovery and concentrate grade in different PGM ores. Higher water and solids recoveries together with higher valuable mineral recoveries (>90% copper and >70% nickel) were obtained from tests using frother blends.

Sep 1, 2012

By J-P Franzidis

A study was undertaken to determine the effect of five industrial frothers on the relationship between entrainment recovery and water recovery. The experiments were conducted using a Batequip rectangular 60 liter steel cell which was run in parallel with the first cell in a copper/silver prefloat rougher circuit. The concentration of the frothers ranged from 2.5 g/ton to 8.4 g/ton. The experiments were repeated at three different froth depths. A power function was found to fit this relationship with no discontinuity in the relationship caused by the changes in frother type and concentration and froth depth.

Jan 1, 2000

By Najdat I. Aziz

There are different schools of thoughts about the influence of gas pressure on coal strength. Researchers have reached contradictory results with regard to the effect of confining gas pressure on tensile strength of coal. Accordingly, this paper re-examines the influence of gas pressure on the strength of coal. A specially designed precision drill capable of drilling in a pressurised chamber was used to drill coal samples under both atmospheric and increased gas pressure environment. The drill cuttings were examined for particle size distribution using a laser controlled Malvern Mastersizer S particle size analyser. Petrographic analysis of the sample examined the effect of gas pressures on the maceral structure and the composition of coal. The paper demonstrates that there is a definite variation in the range of particle size distribution with particles obtained from drilling coal samples not subjected to gas pressures, in comparison with those obtained from samples drilled under confined gas pressure. Also observed were the changes in the rate of drilling in soft coal obtained from geologically-disturbed zones compared with other coal samples. Some variation on the maceral compostion of coals were also observed in relation to increased gas pressures and gas type.

Jan 1, 1996

By M. Soleymani Shishvan

"Continuous mining systems containing multiple excavators producing multiple products of raw materials are highly complex, exhibiting strong interdependency between constituents. Furthermore, random variables govern the system, which causes uncertainty in the supply of raw materials: uncertainty in knowledge about the reserve, the quantity demanded by the customers, and the breakdown of equipment. This paper presents a stochastic-based mine process simulator capturing different sources of uncertainties. It aims to quantify the effect of geological uncertainty and its impacts on the ability to deliver contractually defined quantities and qualities of coal, and on the system efficiency in terms of utilization of major equipment. Two different areas of research are combined: geostatistical simulation for capturing geological uncertainty, and stochastic process simulation to predict the performance and reliability of a large continuous mining system.The process of modelling and simulation in this specific production environment is discussed in detail. Problem specification and a new integrated simulation approach are presented. A case study in a large coal mine is used to demonstrate the impacts and evaluate the results in terms of reaching optimal production control decisions to increase average equipment utilization and control coal quality and quantity. The new approach is expected to lead to more robust decisions, improved efficiencies, and better coal quality management.IntroductionContinuous coal mining systems containing multiple excavators producing multiple products of raw materials are highly complex and exhibit strong interdependencies between constituents. A network of conveyor belts is used for transportation of the extracted materials to different waste dumps or the coal stockpile.Optimal decision-making in short-term planning and production control are impacted mainly by geological uncertainty associated with incomplete knowledge of the coal deposit represented in the reserve block model. These uncertainties cause deviations from expected process performance. For more robust decision-making, understanding the impacts of these stochastic elements plays a key role."

Jan 1, 2016

By L. A. Baker

The presence of goethite in a hematite ore has been shown to strongly affect the time of heating to the firing temperature. The investigation of spalling of single pellets and of packed beds has enabled free water and goethite spalling to be identified as separate phenomena. In addition, it has been shown that even for an 18 inch deep bed of green balls the free water and goethite drying periods can be considered separately. Based on this observation, a method of predicting production rate and hood temperature profile is presented. The method required knowledge of the ore goethite content, ore grind and the green pellet bulk density. Laboratory results were found to be in good agreement with actual plant practice and have led to improved process performance.

Jan 1, 1972

By Huimin Lu, Liyuan Zhao, Zhijiang Gao

The aluminum matrix composite reinforced by graphene was successfully fabricated using high pressure torsion (HPT). With only 0.5wt% graphene, the grain size was reduced to 100nm while that of pure Al was about 500nm. The hardness of the composite increased from the center (64HV) to the edge (120HV) of the sample. Moreover, the tensile strength of this composite reached 197MPa, while that of pure Al was 157MPa. The enhancement in mechanical properties was induced by grain refinement, load transfer from the matrix to the reinforcement and dislocations piled up at the grain boundaries.

Jan 1, 2015

By G. Tranell, L. Kolbeinsen, S. Gaal, J. Safarian

The effect of carbon material properties on the rate of MnO reduction from ferromanganese slag by solid graphite was investigated. A sessile drop technique was used to study the reduction rate of a synthetic slag containing 45 wt% MnO at 1500 and 1600 ºC. Different types of graphite substrates were used and the con-tact angle between slag droplets and substrate were measured in-situ. Moreover, the slag droplet volume during the interaction with the graphite substrates was calculated and normalised. The mathematical relationship between the slag density during the reduction and the normalised slag droplet volumes during the reduction were derived and the MnO reduction curves were then calculated. A method for measuring the slag reactivity of solid carbon was defined and used to qualify the propensity of the different graphites to react with the liquid slag. Some supplementary studies such as manganese evaporation measurement and EPMA analysis for determining the extent of MnO reduction were also carried out. It was observed that there is nota significant difference in the wetting angle of the graphite substrates by the slag, and the wetting is not changed within the temperature range of 1500-1600ºC. However, the changes in the contact angle during the slag reduction at 1600ºC are more than at 1500ºC. The kinetics of MnO reduction is dependent on the type of graphite and it is more dependent on the graphite properties at lower temperatures. On the other hand, the dominant properties of graphite on the reduction rate vary with temperature. A multivariate analysis on the graphite properties and the parameters related to the slag reactivity indicated that the kinetics of MnO reduction is mainly dependent on the temperature, and then on the graphite properties. It was also found that at1500 ºC the surface area and the CO2 reactivity are the most important graphite properties for the slag reduction, suggesting that the reactivity of carbon is rate controlling at 1500 ºC. However, the porosity related parameters are the most important graphite properties at 1600 ºC, suggesting that CO gas desorption is rate controlling at high temperatures.

Jan 1, 2007

Micro-fine disseminated molybdenite was ground in a laboratory stirred mill using steel media and zirconium media respectively. The floatability of ground molybdenite and slurry chemistry was investigated. It was found that the total recovery of ground molybdenite using zirconium media was higher while the pH and Eh of the slurry are lower than that using steel media. When steel media was used, iron oxy-hydroxides had been generated coated on the surface of molybdenite, and decreased the floatability of molybdenite, especially of the -10µm particles. The iron and lead oxy-hydroxides was generated by the reaction between steel media with pyrite and galena associated with molybdenite. It was also found that changing the grinding media to inert can benefit the flotation of molybdenite. Keywords: stirred mill, grinding environment, floatability, micro-fine disseminated molybdenite, fine grinding

Sep 1, 2012

By R Wei, Y Peng, D Seaman

This study addresses a widespread problem confronting the mining industry: the deleterious effect of clay minerals in flotation. This problem is seemingly exacerbated by the presence of iron contamination from grinding media. The interaction of clay minerals and grinding media in copper and gold flotation was investigated in this study. A low-clay ore and a high-clay ore were obtained from Telfer to represent different contents of clay minerals, while stainless steel and mild steel grinding rods were used to produce different grinding chemistry, in particular, iron contamination. Flotation tests on an unsized and sized basis were conducted to reveal how clay minerals and grinding media affect copper and gold flotation. Iron contamination and the oxidation of copper minerals were quantified by ethylene diamine-tetra acetic acid (EDTA) extraction. It is interesting to find that both clay minerals and iron contamination depressed the flotation primarily in fine particles smaller than 33 ¦m, and clay minerals played a dominant role. Although flotation of coarser particles greater than 33 ¦m was less affected by clay minerals and iron contamination, coarser grinding to increase P80 was not an effective way to improve copper and gold flotation for the high-clay ore. This study suggests that to improve copper and gold flotation from clay ores, clay dispersion in conjunction with the minimisation of iron contamination may be required.CITATION:Wei, R, Peng, Y and Seaman, D, 2013. The effect of grinding media on copper and gold flotation in the presence of clay minerals, in Proceedings World Gold 2013 , pp 283-288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Mary E. Learmont

Grinding with steel media adversely affects the flotation response of galena. Electrochemical measurements, flotation tests, and AES, XPS, and STEM examinations were employed to identify interactions between galena and mild steel. Iron oxide, hydroxide, or sulfate species that formed on the galena surface upon contact with mild steel decreased its floatability, with the time of contact and aeration condition affecting the severity of the flotation depression.. Parallel tests performed with an active metal, magnesium, indicated that floatability was also affected by the presence of a surface coating involving lead species.

Jan 1, 1984

By E. W. Thorton

"This paper is intended to show that grinding media can effect flotation results, and in some instances the results are vastly different. I do not suggest that autogenous grinding is beneficial in the separation of all complex base metal ores, in fact I know of a case where autogenous grinding would be disastrous to any selective flotation. I do however contend that prospective flow sheets and reagent balances of any complex base metal ores should be tried with both types of grinding. I feel fortunate that the paper to be presented later in this meeting by Rene Klymouski will, I think, compliment and perhaps explain some of the results of my research.This paper will be in four parts. The first part deals with a literature survey on the subject. Surprisingly enough, very little information has been printed on the subject. The second part deals with results obtained in bench scale tests on an ore from Chester Mines Limited. It was in these tests that we realized that steel grinding was giving us serious problems. So bench scale tests are shown giving results with a stainless steel grind, a mild steel grind and a grind in a ceramic mill with ceramic billets.The third part of the paper deals with results obtained in the Mines Branch Pilot Plant, when again we ground the ore with three different types of grinding media. Incidentally, this has been the only pilot plant test made at the Mines Branch in which flotation products were made on both steel grinding and autogenous grinding on the same ore. The fourth part deals with two other New Brunswick ores and is intended to show that changing the grinding media effects ores other than that of Chester Mines Limited."

Jan 1, 1973

By R. W. Bruce

The normal practice for processing complex sulphide ore has been to grind with steel balls and/or rods in steel mills before flotation. Little thought had been given to the effect of grinding media on flotation selectivity of copper-lead -zinc ore until 1960 when Rey and Formanek(1) published their experiments on sphalerite floatability after grinding in a porcelain mill with ceramic pebbles. The studies by Rey and Formanek had a pronounced effect on the milling of copper-lead-zinc ores in Canada and possibly throughout the world at a time when autogenous grinding was creating a great deal of interest. The impression was created, and possibly still exists with some mill men, that grinding an ore in the absence of steel will result in a loss of selectivity between copper, lead and zinc minerals. This is in spite of the fact Rey and Formanek's experiments showed that the "naturall floatability" of sphalerite was not apparent after grinding in a porcelain pebble mill in an alkaline pulp.

Jan 1, 1976

By Don Langlois, Udo Weber

"The effect of grinding media performance on milling and operational behaviour was demonstrated under different selected milling conditions of calcium carbonate. A variety of grinding media material and bead sizes, along with 2 different stirrer tip speeds, were used in the grinding process to generate a particle size reduction of the calcium carbonate (CaCO3). To determine the optimum milling parameters the collected test data was used to calculate and evaluate specific energy as well as stress intensity under different milling conditions.INTRODUCTIONAs a result of increasing energy costs and raw material prices it is important to look at the efficiency of the manufacturing process. Wet grinding and ultrafine wet grinding in stirred media mills are now a possible cost-effective production step for the processing of industrial minerals and precious metals. The generation of smaller particle sizes (down to micrometer scale) can be advantageous for further production steps – i.e. better liberation of precious metals or improved industrial mineral qualities.In the following, the wet grinding process is investigated under different milling conditions of calcium carbonate. Different grinding media materials varying in specific weight, bead size and stirrer tip speeds are used to determine optimal energy consumption for the milling process.DESCRIPTION OF TEST CONDITIONS AND PARAMETERSMill ParametersTests were performed in a Drais Laboratory Perl Mill PML H/V with an installed electrical motor power of 3 kW. The mill chamber is silicon carbide where as the stirrer and discs are made of yttria stabilised zirconia. The mill working volume is 0.9 l. A screen cartridge with a screen size of 0.2 mm is used to separate the beads and slurry at the outlet of the mill. All tests were performed with a grinding media filling grade of 80% (Mill working volume). The stirrer tip speed was set at 6 m/s and 10 m/s."

Jan 1, 2009

By U. Weber

The effect of grinding media performance on milling and operational behaviour was demonstrated under different selected conditions of calcium carbonate slurry milling. A variety of grinding media materials and bead sizes, along with two different stirrer tip speeds, were used in the grinding process to generate a particle size reduction of the calcium carbonate (CaCO3). To determine the optimum milling parameters the collected test data were used to calculate and evaluate specific energy as well as stress intensity under different milling conditions. Keywords: Grinding, mill media, high energy mills, industrial minerals, precious metals.

Jan 1, 2010

By Frank E. Chase

Geologic structures have been responsible for numerous underground accidents and fatalities, and are a constant-source of down time. During - longwall mining, ground control problems associated with geologic anomalies are aggravated by the abutment pressures which develop as the panel is retreated. Therefore, it is imperative that these structures be recognized and properly supported in head- and tailgates. Fractures, faults, clay veins, igneous dikes, and ancient stream channels (paleochannels) disrupt the lateral continuity of the mine roof and can cause falls in gateroads. Horsebacks and kettle bottoms are also hazardous because abutment pressures tend to "pop out' these structures into the gateroads. This Bureau of Mines investigation describes the physical characteristics associated with hazardous geologic structures, identifies the coal fields where-they have been observed, and, where possible, suggests support strategies and other mine plan modifications to help minimize their effect.

Jan 1, 1990

By A. M. Elmahdy, T. Hirajima, M. Farahat

"Separation of molybdenite from chalcopyrite is mainly achieved through flotation technique to raise their grades up to 25% to be extracted in smelters. However, molybdenite recovery and grade obtained from this process is not satisfactory in most cases due to the natural hydrophobicity of both minerals. The influence of conventional heat treatment on pure chalcopyrite and molybdenite minerals was investigated. X-ray diffraction, TG-DTA and XPS techniques were applied before and after heat treatment. The results showed phase changes for both minerals. Magnetic separation experiments of single and mixture of both minerals at several magnetic intensities were made. For single mineral experiments, 100% molybdenite recovery was obtained at all experimental conditions as non-magnetic fraction whereas ca. 100% chalcopyrite recovery was achieved under certain conditions. In case of 1:1 binary mixture, 87% and 83% molybdenum and copper recoveries, respectively, were obtained. The increase in chalcopyrite magnetic recovery is related to the formation of more magnetic phases as confirmed by characterization techniques.The objective of this study is to increase the magnetism of chalcopyrite to make its separation from molybdenite by magnetic separation possible and to understand the mechanism behind it. These results indicate that it may be possible to upgrade molybdenite ores using heat treatment followed by magnetic separation to the required grade by smelters which is difficult to attain by froth flotation and the other techniques."

Jan 1, 2016

By X. -G. Chen, K. Liu, N. Parson

"Precipitation-strengthening 6xxx alloys are widely used for building and construction and automobile industries due to their high strength, good weldability and corrosion resistance. However, their elevated-temperature properties (250–300°C) decrease rapidly due to the fast-coarsening of precipitates. On the other hand, dispersoid-hardening is one of the most efficient approaches to improve the elevated-temperature properties. Therefore, the evolution of dispersoids during heat treatment in Al-Mg-Si-Mn alloys was investigated in the present work. Various heat treatments with temperatures ranging from 300–500°Cfor up to 24 hours were performed. Electrical conductivity and microhardness were measured while optical and scanning electron microscopy combined with image analysis, were used to characterize the dispersoids. Special emphasis was placed on the evolution of the size and number density of the dispersoids under different heat treatment parameters. It was found that dispersoids started to precipitate at 350°Cfor 1 hour. Nucleation and growth were the main mechanisms at temperatures up to 400°Cwhile coarsening occurred at temperatures above 450°C. The quantitative results indicated that dispersoids precipitation reached the optimum condition after treatment at 400°Cfor 2–4 hours with a fine size and high number density, resulting in the highest hardness.INTRODUCTIONThe precipitation-hardening 6xxx aluminum alloys with major alloying elements of Mg and Si are one of the most widely used aluminum alloys for building and construction and automobile industries (Dinaharan & Murugan, 2012). In recent years, there have been increasing demands for aluminum structural components to be used at elevated temperatures (250–300°C) for different applications. However, the mechanical properties of 6xxx alloys at elevated temperature are typically reduced due to the rapid coarsening of precipitates at 250–300°C. It has been reported that the yield strength (YS) of AA6061 in the peak-aged condition drops from 276 MPa at room temperature to only 30 MPa at 315°C(Kaufman, 1999). Therefore, it is a key concern to improve the elevated-temperature properties of 6xxx alloys to expand their range of applications."

Jan 1, 2018

By K. Narayana Swamy

Experimental results of 3-phase mixing in a physical model of a CCRL for metals refining, at high levels of bottom gas injection (up to a superfIcial gas velocity (Us) of 12.5 cm/min), are presented. A thermal tracer technique was used to elucidate both longitudinal mixing and interphase heat transfer. The results indicate that even under conditions of significant bottom gas injection, it should be possible to maintain acceptably low longitudinal mixing (D. < 20 cm2/s and D/uL < 0.1) in the CCRL. Interphase mass-transfer coefficients of the order of 0.02 cm/s and higher, are predicted from the measured interphase heat transfer coefficients using the mass and heat transfer analogy. Adequate performance is likely to be possible for an industrial CCRL, based on extrapolation of these results to full-scale conditions.

Jan 1, 1996

By Y Xiao, C Lei, C Shu, W Wang, K Wang, J Deng

To investigate the effect on coal spontaneous combustion with high geo-temperature, an experimental apparatus was developed to measure characteristic parameters of two kinds of coal samples at different temperatures: one was 40&#176;C (G coal sample) and the other was a rising temperature from room temperature (C coal sample). Based on the relationship between CO concentration and the temperature variation, a calculation model of the apparent activation energy of coal was established. The results indicated that the oxygen consumption rate, the generation rate of CO and CO2, and heat release intensity of G coal sample were higher than C coal sample. This trend was more and more obvious as the temperature increased. Furthermore, the apparent activation energy of G coal sample was lower than C coal sample, especially at low temperature stage, which demonstrated that the more the oxidation and exothermic reaction of G coal sample was enhanced, the less energy was required to break the barrier of oxidation reaction. Under the same condition, the speed of oxidation reaction was faster for the coal in the high geo-temperature environment, which was more liable to spontaneous combustion.CITATION:Lei, C, Deng, J, Xiao, Y, Shu, C, Wang, K and Wang, W, 2017. The effect of high geo-temperature environment on spontaneous combustion – an experimental study, in Proceedings Australian Mine Vent Conference 2017, pp 137–142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017