Search Documents

By W. Holdsworth

The flotation mill of Dentonia Mines, Limited, at Greenwood, B.C., went into operation on April 20th, 1934, and by October 11th a total of 15,000 tons of ore had been treated. It is intended in this paper to describe briefly the operation and to give some of the operating data which have been gathered. The metallic minerals in the Dentonia ore are pyrite, chalcopyrite, galena, and, occasionally, native gold, and the gangue includes chloritic material, vein quartz, and calcite. Pyrite makes up about 90 per cent of the metallic content of the ore, in which it is disseminated as irregular grains and well-formed cubes. An average analysis of the ore is: gold, 0.27 oz. per ton; silver, 1.73 oz. per ton; copper, 0.12 per cent; lead, 0.31 per cent; and zinc, trace. From the mine ore-bin, situated near the portal of the tunnel at the mine, the ore is hauled by motor truck to the mill, a distance of three-quarters of a mile, and there dumped into the receiving bin, which has a capacity of fifty tons. The hauling is done during one eight-hour shift, commencing at 7 a.m. The maximum size of the ore fed to the mill-bin is ten inches. Lumps larger than this are broken by sledge hammer to pass through grizzly bars, spaced ten inches apart, installed above the bin. The ore is drawn from the bin by a 30-inch, 6-ply conveyor belt, 18 feet 6 inches long. In the near future, when the cross-cut tunnel is completed, the ore will be trammed to the receiving bin. This will effect a considerable saving in cost. At the same time, the bin will be set back several feet, so that the length of the conveyor belt may be doubled. This will make efficient ore-sorting possible, and so ensure a minimum of waste rock in the mill feed.

Jan 1, 1935

By John E. Litz

The Denver Process is a chemical/metallurgical process for treating radioactive or mixed wastes by extraction and concentration of the radioactive and/or hazardous component(s). The process was developed at bench scale, evaluated at pilot scale, and will be implemented at full scale to remediate a low-level radioactive sludge. Six unit operations comprise the process: feed handling, leaching, solvent extraction, electrodeposition, precipitation, and tailing preparation. Unit operation design may be modified to tailor the process for varying feed stock composition. Radioactive or mixed waste is reacted with aggressive reagents in an aqueous phase, solubilizing targeted components. These components are then selectively extracted and concentrated in subsequent steps. Waste solids and solution exit the process as non-hazardous non¬radioactive waste. Dehydration of aqueous waste by submerged combustion eliminates aqueous discharge.

Jan 1, 1994

By P. M. May, V. Gella

The deportment and speciation of trace elements during mining and minerals processing is becoming an area of increasing concern with regards to potential health and environment risks. The use of chemical modelling can enhance our basic understanding of the deportment and speciation of trace metals under conditions present in gold processing solutions, and assist in laboratory and field investigations. In this paper, we report the results of chemical speciation modelling using the JESS software package for the trace toxic elements Pb, Cd, Hg, Se and Te in cyanidation solutions of varying salinity and relate the models to experimental data. The speciation of mercury is examined in detail.

Jan 1, 2011

By J. B. Knaebel, M. W. Von Bernewitz

OUTSTANDING FACTORS that have largely induced the current great interest in the reopening of old mines and the search for new deposits are the increased relative value of gold, the certainty of a market for it, and the decreased activity and poor profits in other lines of endeavor. It is easy to understand why a miner out of a job and unable to find any other means of livelihood would naturally take to the hills with his pan, pick, and shovel; but never before have inexperienced, would-be prospectors and placer miners materialized from the factories and farms, the haberdasheries, and the oil and gasoline supply stations, in such numbers as the last couple of years have witnessed, except when rich strikes of the proportions of a Klondike have been made. What, may one ask, has occasioned this condition? Unemployment has put these men in a receptive frame of mind, and newspaper and magazine articles have done the rest-- The Gold Miner of Los Angeles (a new weekly), The Mid- Week Pictorial (New York) for Sept. 3, 1932, and Popular Science Monthly for August, 1932, for instance. Even the Saturday Evening Post had an article on a promising part of Colorado. Stories that good wages may be had for the panning in nearly every western state have been featured by daily papers, popular "scientific" magazines, and quasi- technical journals. These tales have been eagerly grasped by thousands of people whose ignorance of mining has only served to increase their enthusiasm.

Jan 1, 1932

A Kellogg type computer model of the slag fuming process is applied in reverse to derive some thermodynamic properties of components in lead blast furnace slag. At 1200¦C, the average activity coefficients calculated were 3.40 (S.D. 0.50) for ZnO referred to the pure solid; 0.657 (S.D. 0.022) for PbO referred to the pure liquid; for the ratios y 3.175 y (referred to the Feo.9450, Fe304 pure solids) 4.19 (S.D. 1.15), and for yCaS/ 1CaO (referred to the pure solids) 5.10 (S.D. 2.96). Statistical relationships were derived for these activity coefficients and ratios as functions of the composition of slag, which contained in molar percentages 1.9 - 12.6% ZnO, 19.8 - 24.9% Fe0.9450, 0.9 - 1.6% Fe304, 0.002 - 1.9% PbO, 16.1 - 18.6% CaO, 25.9 - 31.0% SiO2, 4.8 - 5.5% MnO, 9.2 - 10.3% A101.5, 1.2 - 1.4% CaS, and 5.1 - 9.6% "Mgo" (the balance).

Jan 1, 1980

By Benjamin H. Clark

"For over 50 years, Derrick Corporation has been renowned for its innovative and durable fine screening equipment and screen surface technology. Derrick’s latest innovation, the patented Stack Sizer, offers mineral processors both high tonnage capacity and high separation efficiency on an extremely small footprint.The Stack Sizer is suitable for separations from 6.3 mm down to 75 microns (200 mesh). The Stack Sizer, coupled with Derrick’s patented urethane screen surface technology, offers an extremely economical alternative to hydraulic classifiers, hydrocyclones, and less efficient low volume wet screening systems. Stack Sizers have been used in feed preparation for flotation, spirals, and a variety of jigs. Mineral processors wishing to reduce grinding circuit circulating loads and generation of slimes due to over grinding, thereby enhancing the efficiency of flotation and gravity circuits, now have another technology at their disposal to perform this critical sizing and grade control function.Over 200 Stack Sizers have been installed in numerous mineral processing applications worldwide attesting to the rapid acceptance of this technology. Stack Sizers are currently screening ferrous and non-ferrous metal ores, mineral sands, silica sand, kaolin clay, feldspar, garnet, phosphate, aluminum dross, potash, coal, tantalum, spodumene, niobium, and other rare earth mineral ores.INTRODUCTIONDerrick engineers have long understood and demonstrated the importance of screen width in coupling both high capacity and high separation efficiency for fine wet sizing applications. As opposed to fine dry sizing, where the length of the screening machine is critical for high separation efficiency, introducing slurry feed to screens in a thin and even layer at minimal velocities across wider screen surfaces allows for high capacities and efficiencies, with maximum screen cloth life. This is due primarily to the combination of free liquid and high frequency vibration of the Derrick motors, which allow fine undersize material to pass through the screen apertures. Lacking either of these factors would be extremely detrimental to the screening process. Without the high frequency vibration of the motor, the screen is essentially a low efficiency sieve bend. Without the free liquid to carry fines through the screen openings, the screen is for all intents and purposes a glorified conveyor or dewatering unit, as little or no sizing takes place once the screen is devoid of free liquid. For optimal screening results, Derrick recommends feeding slurry to a screen at approximately 20% solids by volume. Figure 1 shows the Stack Sizer design concept. Note that a single feed point is used to evenly distribute the flow to the five separate feed points."

Jan 1, 2007

By Mike Faure

Hercules cribs make use of timber loaded parallel and perpendicular to the grain. Maximum use is made of the orthotropic properties of timber resulting in crib- having superior strength, high initial stiffness and controlled post yield deformations. Blocks and timbers can be combined in many different ways resulting in thousands of different geometries. Each geometry has a specific combination of block on block, timber on timber and block on timber contact area which results in a unique performance. Each crib can be fingerprinted by defining four parameters relating to its load/deformation curve. If the geometry is known, the performance can be predicted with a high degree of accuracy. If the mine support requirements are known, the crib geometries can be designed which met theme requirements in the most cost effective manner Hercules cribs come closest to satisfying mine support requirements. Due to the flexibility of the concept and their superior strength, they can be employed in most mining situations to enhance safety, improve productivity, reduce working costs or improve profitability.

Jan 1, 1993

The construction of mine headframes of reinforced concrete is not a new departure as many structures have been built of this, material particularly in Canada and South Africa. This type of construction has been satisfactorily tested in service and is now accepted by the mining fraternity.The two headframes at New Broken Hill Consolidated Limited are the first structures of this type to be built in Australia, and provide an interesting application of reinforced concrete design and construction.Reasons for Adoption of ConcreteDuring 1947 the writer visited D.S.A. and Canada and inspected three headframes, of reinforced concrete construction.Leading details are as follows:(i) Hollinger Gold Mines. (Timmins, Ontario) : Height of sheaves 110 ft. Shaft has provision for 4 skips each of 12,000 lb. capacity. Structure incorporates surface crushing plant.(ii) International Nickel Corporation-Murray Shaft (Sudbury): Height to sheaves 153 ft. 6 in. Shaft provides for 2-12 ton skips and 2 cages. Surface crushing plant built integrally with frame.(iii) Asbestos-Johns Manviae (Quebec): Height of sheaves 116 ft. Shaft provides for 2 skips 200 cu. ft.

Jan 1, 1956

By J. A. Yeats

This paper describes the loading to 25MN of a 1.2m diameter bored cast-in-situ test pile founded in the Thanet Sand which was base grouted. The pile was sleeved over the major portion of its length to test primarily the base response of the pile. The results are presented and compared with similar pile load tests in Thanet Sand.

Jan 1, 1989

By Mohamed A. Younis, Robert J. F. Goodfellow

This paper investigates the design approaches taken and the philosophy employed during the construction of the Metropolitan Airport Commission (MAC) storm tunnels, part of the Phase 4 Segment of the MAC Trunk Storm Sewer Project at Minneapolis St.-Paul International Airport, located in Minneapolis, Minnesota. URS Corporation was retained to provide a design and Construction Management (CM)services for the MAC Trunk Storm Sewer Project. A case history of the design and construction challenges of the project is presented. The MAC storm tunnels consisted of the construction of twin 10-foot inside diameter (I.D.) tunnels within 7 feet of an existing 72-inch I.D. storm pipe at the base of a 70-foot high highway embankment. The analysis required during the design stage of the project is discussed. This analysis and our design approach provided a defensible framework and justification to make design decisions on relevant issues including: allowable spacing of new and existing structures; preferred order of construction; expected ground deformation behavior; response of lining types to adjacent construction; and effects of proposed changes to design at the submittal stage and during construction.

Jan 1, 2003

By Nichol R

- PART A The Hoppers Crossing Pumping Station is one of the principal components of the Western Trunk Sewer Project which replaces the 90 year old Main Outfall Sewer and will convey 60% of Melbourne's sewage flow from Brooklyn to the Board's Farm at

Jan 1, 1987

By A. Aly Selim

A computer model was developed to calculate the fragmentation cost for in situ leaching operations as a function of the blast design and deposit parameters. The model is based on blasting an ore zone only or an ore zone plus overburden by either a coyote blast or a vertical blasthole system. The model calculates the blast design parameters and the fragmentation cost based either on a user input powder factor value or on a powder factor calculated by the model as a function of the overburden height and the ore zone thickness. Examples of blast design parameters calculated by the model are the number and spacing of blastholes for a vertical blasthole system and the number and spacing of crosscuts for a coyote system. The model also calculates the total amount of explosives, the detonating cord length, and the number of primers. The cost of blasthole drilling can be calculated by the model based either on purchasing and operating a drill or on a user input value of the contracted cost of drilling. Application of the model to an example ore deposit showed that the vertical blasthole systems were more economical than the coyote system when there was no overburden and the deposit had an average ore thickness less than 45 meters. With no overburden and ore thickness greater than 45 meters, the vertical blasthole system was either more or less expensive than the coyote system depending on the number of levels used in the coyote system. With overburden, the coyote system was less expensive than the vertical blasthole system for blasting either the ore only or the ore plus the overburden. A coyote blast will usually produce larger particle sizes than a vertical blasthole system. Larger particle sizes can result in lower copper recoveries so that a less expensive coyote blast may not improve the overall economics of an in situ leaching operation. Blasting the ore zone only was generally less expensive than blasting the ore plus the overburden by either blasting system. Also, for the example considered, the coyote system costs were less sensitive to changes in overburden thickness and powder factor while the vertical blasthole system costs were less sensitive to changes in ore thickness.

Jan 1, 1977

By Brady KT, Pattenden G

A laboratory size solvent extraction apparatus has been constructed, which incorp- orates three stages of countercurrent extraction, followed by two stages of counter- current stripping. The model uses a gravity flow system from one stage to another and air lift pumps to recirculate organic and aqueous phases. A novel pump/mixer system is used to transfer solutions from the mixer compartments to the settler compartments. The model has proven valuable in the teaching of solvent extraction principles.

Jan 1, 1984

By David J. Baxter

Use of bored displacement piles has experienced significant growth in the UK piling market sector, largely due to their environmental advantages over other piling methods and through cost benefits. Bored displacement piles are a cast-in-situ construction which can be formed with minimal production of spoil and offer low noise and vibration compared to driven displacement piles. A large variety of bored displacement piles have been developed. This paper describes a standard system for their classification. The development of the different types is described along with the factors which have led to their increased use. Consideration is given to processes undergone by the soil during pile installation and design approaches for bored displacement piles are compared. Comparisons are made between the different classifications of bored displacement pile. Comments are also made on the installation of such piles. It is concluded that complex changes occur in the stress states of the surrounding soils. Such effect of the pile installation on the soil should be accounted for and there is a need, therefore, to further refine the design process for these piles.

Jan 1, 2006

By V. Mathebula

Paper written on project work carried out in partial fulfilment of B. Tech (Mining Engineering) degree The purpose of this study is to establish whether to mine the Bottom of Pit (BOP)/TOB 4 reserve before the commencement of the Block Cave or whether this should be disregarded and the reserve be extracted at the end of the life of the Cave. The primary goal of this report is to investigate and propose a practical mining method to safely extract the reserve given the set constraints. This report quantifies the additional revenue the TOB 4 will contribute to Finsch?s overall NPV thus enhancing Finsch?s business case and strategically enhancing the SBP. Several underground mining options have been investigated. The proposed mining method includes the installation of a series of extraction tunnels below the TOB 4 reserve from 53 level, with a slot access tunnel system. Ground will be loaded by LHDs from the draw points and tipped into 50-ton dump trucks at a transfer point, from there the ground will be transported to 53 level No. 1groundpass where it will join the existing ground-handling system. Primary development is scheduled to begin October 2002 and last for a period of approximately 7 months until early April 2003.The production is broken into 4 phases. Phase 1 is scheduled to begin mid-April 2003. The final production phase will be completed by November 2005. The production scheduling has been designed in order to remain ahead of the Block 4 undercut in order to ensure stability and safety. Due cognisance was taken of the health and safety of all employees concerned during the design of the mining and ground-handling processes for the Bottom of Pit. As far as is reasonably practicable, the BOP was designed and will be constructed and equipped to provide conditions for the safe operation of machinery and a healthy working environment for people underground. Relevant requirements of the Mine Health and Safety Act regulations pertaining to mining operations have been identified and adhered to during all phases of the design process.

Jan 1, 2004

By M Ogle

"Booster fans are relatively rare in Australian coal mines. However, as mines become progressivelydeeper it is likely that such fans will be increasingly adopted as a method to sustain or improve the ventilation of underground workings. The reasons why booster fans may be an att ractive alternative include: increased cost of sinking additional ventilation shafts with greater seam depths; environmental objections to shaft sinking projects; and increasing urbanisation and surface constraints limiting availability of potential ventilation shaft sites. As Tahmoor Colliery movedinto its northern lease the ventilation constraints became the limiting factor on production. Thelimitations of the old workings meant that the existing ventilation system would be inadequateto sustain the required production. Extensive ventilation modelling was carried out to evaluatevarious potential solutions and the recommended option was the installation of a booster fanor fans, to gain underground access to an already approved shaft site in the northern lease.Proposals were sought from recognised fan manufacturers and various alternative arrangements were tendered. Ultimately the choice was between one large centrifugal fan and a set (three or four) of smaller æauxiliary-likeÆ fans in parallel. The successful tender was for a single centrifugal, an arrangement very similar to the booster fans that have been operating eff ectively at Westcliff Colliery for a number of years. This paper describes the current ventilation network, evaluation of the ventilation options, the fan selection process, and the project status to date."

Jun 1, 2012

By Rob Thomas

"In Australia, a wide roadway is commonly defined as any roadway that is driven to a width greater than 5.5 m (18 ft). These roadways are typically required to enable the installation of longwall equipment (termed installation roads); however, other applications include the need to house conveyor driveheads and pre-driven recovery roads.As a result of the increasing size of longwall equipment and mine infrastructure, in some mines, roadway widths of between 9 and 12 m (30 and 39 ft) and are being developed.Accepting that these almost always constitute strategically important and often long-term roadways, this paper considers the use of: (i) an empirical roof support design model, which is based on over one hundred case histories, (ii) various roof support design principles, and (iii) commonly accepted strata management techniques.The paper demonstrates that wide roadways can be driven and supported to an acceptable standard providing due consideration is given to the prevailing ground conditions (including the quality of the immediate and upper roof strata, the Depth of Cover and the horizontal stressfield), the final width of the roadway and the required use of the roadway.INTRODUCTIONRoof behaviour and the associated roof support requirements in wide roadways, which are roadways typically driven to a width that is greater than 5.5 m (18 ft), are controlled by a number of key geotechnical and operational factors. The recognition of these factors is an important first step in the design process and it is imperative that each is considered in conjunction with local mine site information.The main points of note in this regard can be summarised as follows:• The greater the final width of the roadway, the greater the resulting surge in roof displacement on widening - note: a) see Figure 1 for a schematic illustration of the roof displacement trends typically measured during the development of the first pass and roadway widening, b) since displacement increases with roadway width, it is always recommended that the roadway width is kept to the minimum required and c) general buckling beam theory indicates that the capacity of any beams present in the roof will reduce in inverse proportion to any increase in roadway width squared (i.e., [final width2 -first pass width2] I final width2)."

Jan 1, 2010

By Christopher Hebert, Michael R. King, Mehdi Ghazi

The Inland Feeder project is a critical component of Southern California’s water delivery system, relying on a strategic plan of water transfer and storage to enable the delivery of an additional 650 million gallons of water a day. The Arrowhead West and Arrowhead East tunnels form part of this system, comprising the construction of nearly13 km (8 miles) of bored tunnel under the San Bernardino National Forest. This paper describes the design and manufacture of the 4.88 m (16 ft) diameter precast segmental primary lining that will be used in these tunnels to resist rock loads, and up to 275 m (900 ft) of external hydrostatic head.

Jan 1, 2003

In 1948, it became clear that the ventilation system of The Zinc Corporation Limited and New Broken Hill Consolidated Limited mines, would be inadequate for future operations. The,paper describes in detail the process of designing an entirely new ventilation system for a large underground mining operation. The system was based on a single new upcast airway to be located on the boundary of the two properties, which were to be ventilated in parallel as two separate ventilating districts.From calculations of resistance, and assessments of future air requirements, the duties of a new exhaust fan to be located on the collar of the upcast airway were specified as 700,000 cubic feet per minute at 2·6 in. w.g. total pressure for initial operation in 1953 increasing to a maximum of 900,000 c.f.m. at 3·6 in. w:g. total pressure ten years later. The economic size of the new airway was calculated from a consideration of the first thirty years operation of the system, and it was decided to provide a 20 ft. diameter concrete-lined shaft.The new system went into operation five years after the initial planning, and the effect of the difference between actual and predicted rates and distribution or production are discussed. The final result was entirely satisfactory.INTRODUCTIONThe first proposal for an investigation of The Zinc Corporation Limited-New Broken Hill Consolidated Limited ventilation system with a view to putting it on a proper technical basis was made in 1938. A new Main Shaft was then being sunk, and it was decided to postpone the enquiry until this had been completed to No. 14 Level, when operations would be temporarily suspended and the shaft commence to operate as a major airway. The investigation was completed early in 1940, when Z.C. Ltd. upcast fan was...

Jan 1, 1956

In dense medium processes for the beneficiation of minerals the consumption of medium (generally ferrosilicon) represents a major component of the operating cost. This provides a strong incentive for improvements in heavy medium recovery circuit design and operation. A major thrust in heavy medium plant design over the past decade has therefore been towards circuits which reduce medium losses. In this paper recent trends in plant design are examined in relation to the factors infl uencing circuit performance and medium losses. Operational details ' which have a significant effect on losses are discussed and illustrated by means of plant and pilot plant test data, with particular emphasis on the performance of wet drum magnetic separators. While the emphasis is on reducing the consumption of the high-cost ferrosilicon medium used in minerals beneficiation, most of the principles described in this paper are equally relevant to the design and operation of magnetite recovery circuits for coal preparation plants.

Jan 1, 1987