Search Documents

By David E. Thompson, Wesley E. Stimpson

The Massachusetts Bay Transportation Authority (MBTA) Red Line Extension Northwest is currently in the early stages of construction. The 3.1 mile extension of the Red Line from the existing Harvard Square Station in Cambridge, Massachusetts to Alewife Brook Parkway in Cambridge, Massachusetts will include a large, near surface hard rock, rapid transit station chamber at Porter Square in Cambridge (Figure 1). [ ]

Jan 1, 1979

By Edward Thomas

Yucca Mountain Overview The U.S. Department of Energy?s Yucca Mountain Project is a geologic repository project designed to receive, handle, package, transport, and emplace spent nuclear fuel and high level radioactive waste. The planned repository would be located in Yucca Mountain on the western edge of the Nevada Test Site, about 90 miles northwest of Las Vegas, Nevada, and would include both surface and subsurface areas. Yucca Mountain rock formations consist of successive layers of volcanic rocks (called tuffs) approximately 14 to 11.5 million years old, formed by eruptions of volcanic calderas to the north. With the volcanic rock the potential for methane emission is not an issue and the subsurface repository is a non-gassy (methane) classification. This paper will provide a summary of the development ventilation system design that provides fresh air for subsurface construction activities, and the emplacement ventilation system design that removes heat generated by the waste packages. The subsurface layout, illustrated in Figure 1, contains 108 emplacement drifts, one Performance Confirmation(PC) observation drift, nine intake/exhaust shafts, and three access ramps. The existing Yucca Mountain facilities, shown in bold lines in Figure 1, include a 7.8 km long, 7.62 m (25 ft) diameter U shaped tunnel that is formed by the North and South Ramps at both ends of the Exploratory Studies Facility (ESF) drift and a 1.5 km long, 5.0 m (16.4 ft) diameter Enhanced Characterization of the Repository Block drift (ECRB) that were constructed from 1994 through 1998. These drifts were used for site characterization activities and have been incorporated into the subsurface repository configuration. The unexcavated perimeter access main and exhaust main drifts are typically 7.62 m (25 ft) diameter TBM excavations and the emplacement drifts are 5.5 m (18 ft) diameter TBM excavations. The turnouts leading into the emplacement drifts are to be excavated by either mechanical, or drill and blast methods and serve as the launch chambers for the emplacement drift TBM excavations.

By Malte J. M Gurgel

Subsurface spatial planning is becoming increasingly important in view of competing underground applications. This development is influenced by global agreements to reduce greenhouse gas emissions. Therefore, precise knowledge of the underground space is a basic prerequisite for future applications. The three-dimensional registration and reliable georeferencing of underground infrastructures can establish a holistic geodata basis for such tasks. Those tasks are discussed both for the development of energy projects such as deep geothermal energy as well as for storage applications. Research on geothermal energy has been carried out at RWTH Aachen University as part of the SuperC project in a license field in the Aachen area since 2001. Recently, this research has been extended to include monitoring aspects in the overlapping GEObservatorium Aachen field. The documentation and visualization of underground activities using photogrammetric methods like Structure from Motion is discussed based on recent research in sites for the final disposal of radioactive waste. Finally, both applications provide an outlook on supporting underground projects by using high-resolution geodata.

Feb 1, 2025

By C. E. Lancelle, J. T. Volk, H. F. Wang, D. Fratta

"The Main Injector Neutrino Oscillation Search (MINOS) Near Detector Hall at Fermilab and the Lafarge – Conco Mine are located approximately 100 meters underground in the Galena-Platteville dolomite just below its contact with the overlying Maquoketa shale in Northeastern Illinois, USA. A new cavern was excavated adjacent to the MINOS Near Detector Hall at Fermilab to house the near detector for the Off-axis Neutrino Appearance Experiment (NOvA) program. During this excavation approximately 1150 cubic meters of shale rock were removed. Tiltmeter arrays consisting of a series of hydrostatic leveling sensors (HLS), which are spaced regularly over a total distance of 50-to-100 meters, were used to monitor subsurface deformations. The tiltmeter response in the MINOS Near Detector Hall due to the NOvA cavern excavation is approximately thirteen times the estimated response based on using laboratorydetermined properties. The discrepancy between modeled and measured tilt is likely due to differences in Young’s Modulus in the rock mass versus in a small laboratory sample. Amplitudes of measured solid earth tides differ from the amplitudes of theoretical solid earth tides by up to 40 percent for both arrays. This is likely due to a local heterogeneity or discontinuity.INTRODUCTIONLong baseline tiltmeters have been used to record small earth movements since the early 1900s. One of the first studies using long baseline tiltmeters to measure earth tides was published by Michelson (1914). He used a leveled 152-meter long, 0.15-meter diameter tube half-filled with water connecting two concrete-lined pits. The pipe was trenched 1.75 meters underground in Williams Bay, Wisconsin in a sandy-clay soil. Initially only an east-west line was used, though a north-south line was added after it was seen that viable results were obtained. Measurements were made by hand either hourly or once every two hours depending on the time of day. When compared to 0.7 times the calculated earth tides, the tiltmeter signal matched almost exactly. This excellent result began the use of long baseline tiltmeters to measure small earth movements."

Jan 1, 2015

By B Taylor, S Evans

Bulk explosive technology for underground mining has not seen any significant technological advances since the widespread transition from ammonium nitrate fuel oil (ANFO) to ammonium nitrate emulsions (ANE) commencing in the 1980s. The in-hole energy profile that conventional ANE systems deliver is limited by the physics of chemical gassing and simple control systems. This compromises the range, precision, and accuracy of energy delivery into the blasthole, and in some cases limits the length of charge that can be delivered. Orica’s 4D™ bulk system removes many of these constraints, enabling better blasting performance across all underground mining methods. This paper reviews work completed at three mining operations across Australia, the United States, and Chile with a focus on how this system can improve mining operations and deliver sustained commercial and productivity benefits into the future. These benefits include improved ore recovery, reduced dilution from waste rock, and reduced overall explosives consumption. This paper also reviews how this new technology can be applied for planning future mining operations.

Sep 1, 2024

By J. Kretschmann

?We have constructed a world in which the potential for high-tech catastrophe is embedded in the fabric of day-to-day life.? (Malcolm Gladwell) The mining industry is a crucial provider for virtually every person?s needs and thus indispensable. Yet, mining is a complex and risky business: plenty of high risk factors can occur and severely affect nature and the miner?s life and health. Especially for small and medium enterprises (SME) risks may also threaten the economic existence of the company. The responsible and sustainable management of a company should thus be based upon the systematic finding and handling of risks or briefly upon an efficient risk management system. Why do we need risk management? Because nobody is perfect and we make mistakes in the normal course of operation.

Jan 1, 2011

By Hector O. Romero, Paulo C. Fernández A, Claudio C. Gajardo

Phase 06 of the Los Bronces mine, currently under extraction for development, has the particularity of being close to the installations and buildings of a neighboring copper mine. Therefore, the blasts must ensure the continuity of the operation without affecting the nearby structures of the neighboring district, which include Maintenance sheds and Warehouse. Specifically, the safeguards consider a scenario that includes: - Flyrock projections (<150m) - Edge profile studies - Vibrations according to the NCh3577 standard - Nitrous gases Additionally, Phase 06 is also within Los Bronces, so strict control over spillage into the pit is necessary to avoid blocking ramp access to this level. The challenge lies in protecting not only the operation and facilities of the neighboring mining district but also the operability of Los Bronces. Thus, addressing these considerations, blasting configurations are developed with prior simulation of vibration models, flyrock, and spillage in all blasts, with strict control of technical design and implementation to ensure the results. Currently, blasts are successfully executed with control of projections based on the proximity of the projects, vibration (<40mm/s) with decoupling of holes of 17 mm/s between holes, reactive rock tests for explosive selection (loading advancement), and spillage simulation inside the pit according to the loading design; thus, ensuring operational continuity and mine development.

Jan 21, 2025

By H P. Rossmanith

This contribution addresses the advanced blasting technology which is based on wave propagation theory and fracture mechanics. The new concept of sonicity and the principle of maximizing sonicity in blasting as well as the energy or work of a blast operation will be introduced. It is shown that - in contrast to common belief – it is not the velocity of detonation which controls the blast but the relationship between velocity of detonation and the wave speeds, in other words, the Mach numbers of the blast operation. Based on numerous practical blasts in Germany, the authors show that, when using wave dynamic concepts, there is a linear relationship between peak particle velocity and the work of a blast operation and this linear relationship is controlled by the sonicity of the blast. Extensions to layered and faulted rock masses are presented. It will become clear that a second change of paradigm is enforced, the first one being the implementation of short time delaying. Again, the acquisition of knowledge in wave progation theory and fracture mechanics becomes mandatory in advanced blasting technology, where the art of blasting is now fully transformed into a science of blasting with little room for methods of trial and error.

Jan 1, 2010

By Tom Lewis

The metal finishing and electronic industries are searching for ways to recycle materials · and reduce costs. The areas of heavy metal waste and water recycling has gained new interests with the potential of impacting the operation's bottom line. Lewis Environmental Services, Inc. has completed numerous heavy metal recovery and effluent recycling projects with its ENVIRO-CLEAN PROCESS for government and private sector clients. This patented process utilizes a proprietary chemically treated granular activated carbon with enhanced heavy metal adsorption capabilities combined with electrolytic metal recovery to produce a saleable metallic product. The process generates no sludge or hazardous waste and the effluent meets EPA .limits. This paper covers several heavy metal removal projects, two fullcscale commercial installations, and one treatability case study.

Jan 1, 2000

By J. C. Haptonstall

Stoping methods at the Homestake Gold Mine through 1978 had been traditional overhand cut-and-fill, shrinkage or square set. High costs, low-productivity and safety concerns prompted the mine to search for and adopt a "bulk mining" technique as a primary stoping method. Blasthole stoping had been successful but it is very development intensive, and was not suitable for the mine&apos;s accelerated mining program. Vertical Crater Retreat stoping was selected, and today accounts for over 50% of ore production. Case histories representing both the successes and failures of VCR stoping in the mine are discussed.

Jan 1, 1986

By C. Allen, V. Hensel, J. S. Stachulak

"Vale has been actively evaluating new technologies to curtail diesel emissions. This paper discusses the selection, installation, operation, and evaluation of the MANN+HUMMEL SMF®-AR diesel particulate filter system to reduce diesel particulate matter emissions in underground mines. The system uses a sintered metal filter element, an iron fuel-borne catalyst with an onboard dosing system, an electric heater that uses onboard power, and a sensor-based control unit. More than 6,000 h of testing demonstrated that the system represents a breakthrough in the successful control of soot emission from light-duty vehicles with differing soot emission levels, exhaust temperatures, and duty cycles.RÉSUMÉ La compagnie Vale évalue activement de nouvelles technologies pour réduire les émissions de diesel. Le présent article discute du choix, de l’installation, du fonctionnement et de l’évaluation du système MANN+HUMMEL SMFMD-AR de filtrage des particules de diesel pour réduire les émissions de particules de diesel dans les mines souterraines. Le système utilise un élément filtrant en métal fritté, un catalyseur à base de fer dans le carburant avec un système de dosage intégré, un élément de chauffage électrique qui utilise l’alimentation incorporée et une unité de contrôle avec un capteur. Plus de 6 000 heures d’essais ont démontré que le système représente une avancée pour réussir à contrôler les émissions de suie des véhicules légers avec différents niveaux d’émission de suie, différentes températures d’échappement et différents cycles opératoires."

Jan 1, 2015

By D. Bour, C. Nyikos, R. Curtice

Fire in a coal mine can be disastrous on many levels. In most cases, when a fire is detected, mining operations cease and all personnel are evacuated. Underground coal-mine fires are difficult to extinguish, can burn for a long time, and often result in an extended period of lost production. In a worst-case scenario, the mine is permanently sealed and abandoned, resulting in lost jobs, lost natural resources, and possible devastation of the local economy. In some cases, seals placed within the mine to isolate the fire could eliminate the need for sealing the entire mine and the subsequent extended delay in returning the mine to full operation. Previous attempts to place remote seals to extinguish mine fires in active mines have been largely unsuccessful. The West Elk mine experienced an underground fire in early 2000. The fire could not be accessed and extinguished from the active mine workings. A method of constructing seals remotely by drilling boreholes into the affected area was needed to help isolate and extinguish the fire. This paper describes the process by which remote seals were constructed that successfully isolated the fire and provided a means of extinguishing the fire by flooding the area with water. The period of lost production in the West Elk mine was considerably shorter than is typical in similar situations.

Jan 1, 2002

By D. C. Oldroyd

Western Coalfield?s Tandsi Mine, has difficult support conditions and a history of roof falls, resulting in mining roadway widths and depths being restricted for safety reasons. Rock Mechanics Technology Ltd was contracted to improve the support system to allow the introduction of mechanised room and pillar mining. The introduction of a ?world best practice? bolting system resulted in major improvement in roof stability, allowing mining restrictions to be lifted and Tandsi to become one of the first two Indian mines to introduce a mechanised continuous miner system. The first year?s production was some six times previous levels. Because of the improvement in the support system, RMT was also able to design a partial de-pillaring system suitable for the Tandsi continuous miner districts together with the introduction of monitoring procedures and guidelines to maintain safe roof support conditions. In situ monitoring of pillar and roof behaviour was undertaken as the first pillars were extracted to confirm the design. De-pillaring operations have also proved highly productive, and to date there has been no associated support related major injury or dangerous occurrence. The success of this project demonstrates the potential for mechanised room and pillar mining in India.

Jan 1, 2006

By Mike Harrington, Tung Vu

The Regional Connector Transit Project is a 1.9-mile-long underground light rail system that will connect LA Metro’s A (Blue), E (Expo), and L (Gold) Lines in downtown Los Angeles. This $1.75-billion design-build project is scheduled for revenue service in Spring 2023. The project consists of 21-foot diameter twin-bored tunnels, a 300-footlong crossover SEM cavern, three new underground stations (at 1st Street/Central Avenue, 2nd Street/ Broadway Avenue, and 2nd/Hope Streets), and cut-and-cover tunnels along South Flower, Alameda, and 1st Streets. This paper, which is the continuation of our previous paper presented in RETC 2019—LA Metro Regional Connector Transit Project: Successful Halfway-Through Completion, will provide insight regarding the construction of major components, and the system integration and testing work undertaken for this complex transit project.

Jun 13, 2023

By Kevin Hegerle

The Henderson Mill has operated over a wide range of production rates, feed grades, manpower levels and recovery targets since start-up in 1976. Henderson Mill personnel, both management and hourly, have successfully responded to these changes by not only maintaining unit costs, but by actually decreasing unit costs. Methods of cost reduction have included conventional austerity programs, innovative technological improvements and creative work schedules. This paper addresses both maintenance and operating cost reductions and efficiency improvements.

Jan 1, 1986

By Mike Samuels, John Starkey

"This paper examines test results and grinding mill design for the recent Fortune Minerals’ NICO Project, located in the Northwest Territories. SAG milling and rod milling options are compared. Rod milling is clearly shown to be the best option because of the ore’s extreme resistance to breakage in a SAG mill environment.Surprisingly, the Bond Ball Mill Wi was 13 kWh/t for this ore. The Bond Rod Mill Wi was 20 kWh/t, whereas the SAG pinion energy to grind the ore to T80 1.7 mm was 30 kWh/t. The existence of ore with this ratio of SAG hardness to Bond BM Wi has not been previously observed. If not considered, this critical relationship may adversely impact the accuracy of mill design. This paper substantiates the significance of these findings to achieve successful grinding design on ore that is macro-competent during primary size reduction, but relatively normal during secondary grinding.INTRODUCTIONThe NICO Cobalt-Gold-Bismuth-Copper deposit is located 160 km northwest of the City of Yellowknife, Northwest Territories. It is the largest IOCG-type deposit (aka Olympic Dam-type) currently recognized in Canada with Mineral Reserves of 21.8 million tonnes contained within a larger 57 million tonne, lower-grade Mineral Resource. The project, owned 100% by Fortune Minerals Limited, has been assessed in a positive definitive feasibility study, subject to underground test mining and pilot plant testing, and is now in the permitting stage to develop a combined open pit and underground mine and process plant. An updated process flow sheet incorporates conventional crushing, grinding and bulk flotation, followed by filtration for shipment of a concentrate to a purpose-built refinery proposed to be built near Saskatoon, Saskatchewan. At the refinery, separate bismuth and cobalt concentrates will be produced following regrinding. The hydrometallurgical process methods include: pressure acid leach, precipitation, ion exchange, and electro-winning for recovery of cobalt as 99.8% cathode; solvent extraction and electro-winning of by-product copper cathode; ferric chloride leach and electro-winning for recovery of bismuth as 99.5% cathode; and cyanidation of the leach residues for recovery of gold as doré."

Jan 1, 2010

By George Meadows

Consultation and Accommodation Introductions Consultation -Best Practices The Role of Negotiations The HVC Experience Summary / Conclusions The Challenge Meeting legal and policy obligations to consult while adhering to project priorities, timelines and budgets Defining who needs to be consulted, by whom, and ?how much?? Accommodation ?who is responsible and what is the appropriate scope? Social License -establishing positive working relationships with First Nations involved in project review / approvals / implementation in a manner that advances the interests of all parties

May 1, 2010

By V Yadi

Geostatistics has been widely used for more than four decades as a powerful tool in ore resource/reserve estimates and grade control. This method has gradually replaced the conventional method such as polygon and cross-section for grade estimation by more mathematical techniques such as kriging. The advances in geostatistical understanding and the availability of appropriate software packages have given much more contribution in speed and high accuracy during production. However, in many cases, these techniques are sometime applied without support with a good thorough understanding of the geological controls on metal distribution. To produce the result close to actual, the geological control in interpretation and appropriate geostatistical task is a must. Geological logging was described in the core must be consistent with the level plan produced by commercial modelling software used as a guide for grade control during production. Experience gained through evaluation of the Central I deposit resulted that the most effective systems continue to be based on geostatistical methods of resource estimation. Computer applications modelling software packages are necessarily as the core of an efficient in undertaking these assignments. They contribute to make a valued to data management and are becoming increasingly effective during processing. The latter role is particularly important to check the actual versus estimated values where will significantly to improve personnel to have a confident with their knowledge combined with experience and complete their jobs satisfy.

Aug 22, 2011

By Arkady Senchenko

At present, there are different traditional and modern methods for ore grindability evaluation. The correct and rational approach to sampling, testing methods and mill sizing enables one to design a workable technology. This paper contains TOMS institute experience in different grinding indices determination over the last 7 years (SAG Design Test, BWi, CWi, RWi, and other). Mill sizing examples and circuits modeling for the projects in Russia and Kazakhstan are considered. Keywords: ore grindability, SAG Design Test

Sep 1, 2012

By Om P. Garg

During the period between 1970 and 1974 the Iron Ore Company of Canada had embarked on a detailed program to evaluate all aspects of mine design work for its open pit mines around Schefferville, located both in Quebec and Labrador, Newfoundland, Canada. One of the main conclusions was that the majority of the slope angles for the ultimate pit walls could be steeped. During the period 1975 and 1976,five (5) open pit iron ore mines were redesigned using the steeper slope angles up to 55 degrees. Initially these pits were designed at slope angles varying between 37 degrees and 45 degrees due to the generally fractured and leached nature of rocks in the area. During the active mining phase between 1976 and 1979, the stability of the steeper ultimate pit walls was monitored. The mining of ore was successfully completed in 1978 and 1979 in three pits. This of course, resulted in a significant savings due to a reduction in the quantity of waste that had to be removed. The successful pit slope redesign project was a co-operative effort between the Federal Government, Universities and the Iron Ore Company of Canada.

Jan 1, 1983