Search Documents

By Ningchuan Feng

A biosorbent, the chemically modified orange peel, was prepared from hydrolysis of the grafted copolymer, which was synthesized by interacting methyl acrylate with cross-linking orange peel, and FT-IR spectroscopy was used for determining the structure of the biosorbent. Adsorption characteristics and effects of various factors of the biosorbent on Cu (II) were investigated including pH, adsorption time and initial concentration of Cu (II). Experiment results show that when pH was 6.0 and the initial concentration of Cu (II) was 50mg·L-1, the removal rate was 91.7% after 3 h adsorption. After four cycles being reused, 85.3% removal rate could be obtained by the biosorbent.

Jan 1, 2008

By Jiang Fan, Liu Shi, Wang Haigang

Winter-time natural convection in gravel embankments has been suggested as a technique to provide passive cooling and thereby avoid thaw-settlement of roadways located in permafrost areas. Numerical simulation by finite volume method on the proposed model is perf9rmed using the software FLUENT. A gravels model, in which the embankment is composed of stones and air, has been adopted to investigate the temperature and velocity fields in embankment. Simulation results show that in summer, a weak clockwise circulation of the pore air extending throughout most of the embankment. The pore-air motion is very weak which results in relatively straight horizontal isotherm lines. And heat transfer is mainly maintained through conduction. But in winter, pore-air velocities are higher and multiple vortexes are formed in the embankment. Natural convection then becomes the dominant influence on the isotherm shapes within the embankment. As a result of low ambient temperatures exerted on the embankment surface during winter months, an unstable air density gradient develops within the embankment. This convection increases the heat flux out of the embankment. Therefore, the winter-time convection can further reduce the temperature of the foundation soil beneath the open-graded embankment. In addition, the effects of the size of the stones within the embankment have been analyzed and compared in the gravel model. It shows that in winter, 200mm stones lead to stronger vortexes in the embankment compared with those of 60mm stones. Consequently, the zone oflow-temperature beneath the embankment is extended.

Jan 1, 2004

By Q. J. Liu

The flotation circuit and the reagents of the all-sliming flotation about low grade and hard operation on zinc oxide ore are researched in the paper. The results indicated that there are many types of zinc minerals in this ore, and the composition is very complex. They include hemimorphite, smithsonite, hydrozincite and so on. The ore is seriously sliming. In light of the ore properties, three kinds of flowsheets have tested. They are gravity concentration (cleaning tables), flotation, combined process of gravity concentration and flotation. The test showed that the recovery of zinc is only 17.08% in the gravity separation. In combined process of gravity separation and flotation, the recovery of zinc concentrate is close to 70%. But the flow-sheet is complex and hard to control in the production. The floatation circuit is feasible. In the test, it pay attention to investigate the new combined reagent which is used in selective all?sliming flotation process. The effects of slime are eliminated by the multi-loop treatment of middling. In flotation, the final recovery of concentrate is 88.76%; the grade is 29.50%. The recovery of physical ore is 93%; and the recovery of -10mm fraction is more than 65%.

Jan 1, 2014

Reverse flotation process tests were conducted for marine sedimentary silicon-calcium phosphate ore in this research. The research findings showed that by adding antifoamer, a concentrate with P2O5 32.36%, SiO2 10.69%, MgO 0.67% was obtained, with recovery of P2O5 being 88.12%. Such is a satisfying result, when compared with the original mineralogical component of P2O5 26.64%, SiO2 11.51% and MgO 3.36%. When using antifoamer, the SiO2 grade of the concentrate increased 0.55%, the MgO grade decreased 0.64%, while P2O5 recovery increased 2.69% compared by adding no antifoamer. Adding antifoamer is favorable to increase the grade and recovery of P2O5. Therefore, antifoamer is necessary. Tests of synergistic reaction of antifomer indicate that the appropriate consumption of the antifoamer is 275g/t CY and 1Kg/t TWF. Keywords: silicon-calcium phosphate ore, desilication, antifoamer, reverse flotation

Sep 1, 2012

By Zhou Junwu, Sun Chuanyao, Wang Fuli

"In this present paper, the authors introduce the artificial neural networks into the modeling of the industrial flotation process, integrating information technology, control theory and intelligent optimizing method to flotation technology. The new idea gives a new way to solve the difficulty in this field, and therefore brings the study on the automatic control of flotation process in China into a new start.The Radial Basis Function (RBF) network, featuring a quick learning speed, is one of the feedforward neural networks. It has attracted much attention from automatic control recently for its implementing the nonlinearity mapping through adjusting the parameters of the nonlinearity transfer function. One of the online adaptive learning algorithm—the nearest neighbor-clustering algorithm, which can automatically determine the number of hidden units, has been implemented in the MATLAB programming language in this paper, laying the foundation for the flotation models.The relation model between ore pulp characteristics and reagents consumption has been proposed using the RBF networks based on the industrial lead rougher flotation of lead & zinc ore, and the simulation has been conducted in the laboratory with the results matching the samples data very well. The Xilin Lead & Zinc Mine Flotation Process Intelligent Consultation System of Reagents Consumption, which suitable for industrial process, has been developed. The reagents consumption advised by this system would stabilize the flotation process, and increase the recoveries. It could be used for providing the technological consultation to flotation operators in site, and for training new operators."

Jan 1, 2003

By F. S. Niu

With the feature of finely-dissemination particle and complex mineral composition, oolitic hematite is considered to be the ore dressing difficult problem in the world. Series research on refractory oolitic hematite in Zhangjiakou Area are introduced as following: ore properties?technology mineralogy and mineral processing technology. The survey shows: with the fine grinding of the hematite to a fineness of -0.076mm 95%, obtaining iron concentrates grading 62.74% Fe at the recovery of 46.80% by high intensity magnetic separation- reverse flotation flowsheet; under the three stages intensity magnetic separation,four stages grinding and four stages gravity separation, getting the iron concentrates grading 61.09% Fe at the recovery of 45% using high intensity magnetic separation- gravity separation flowsheet; with roasting temperature of 800°C, time for 75~90min and ore-coal ratio of 11, gaining the iron concentrates assaying 62.74% Fe at the recovery of 87% by roasting- magnetic separation flowsheet. At present, this research is still doing for the target of raising the concentration recovery on the base of high grade concentrate. It is in the hope of fully utilizing the existing hematite resources in Zhangjiakou

Jan 1, 2014

By I. Silin, H. Wotruba, J. Huben, A. Ognyanova

"With increasing shortage of raw materials, the beneficiation of ultra-fine ores will play a larger role in the near future. Many established process technologies do not yield satisfactory separation results for ultra-fine materials. Without selectivity, high-grade concentrates cannot be produced. The material at hand is a taconite which had to be ground to d(90) = 25 µm to guarantee liberation of the iron oxides. The comminution was done by High Pressure Grinding Roll (HPGR) and resulted in smooth surfaces and clear grain boundaries. This is an indication of selective grinding and mineral liberation. Further processing steps included selective desliming, magnetic separation as well as reverse flotation. INTRODUCTION During the last centuries, the processing of iron ores became increasingly important. The coarse-grained, so-called lump ores that are ready for direct usage in blast furnaces without further processing are becoming gradually less abundant. The processing of ultra-fine-grained ores, which in addition require a complex ore beneficiation due to the composition of the material, will progressively gain relevance with increasing resource shortages in the future (Arvidson, 2013). The term “ultra-fine” does not hold a precise definition in mineral processing. In this paper, “ultra-fine-grained” ores are defined by the required grind size for full liberation smaller than 20 µm. Many established mineral processing technologies do not yield satisfactory separation results for ultra-fine materials. Thus, they are limited in their application to produce high-grade concentrates suitable for sintering and pelletizing for direct reduction processes. The production of a high-grade iron concentrate (over 68% Fe) with low silica content (under 2.5% SiO2) is possible from both magnetite and hematite containing ore. In addition to the mineral processing technologies (magnetic and gravity separation, flotation), technologies for the liberation of fine-grained iron ores need to be developed and improved. In contrast to the conventional wet grinding circuit by means of tumbling mills, several future trends in dry and wet grinding and regrinding are already in use. These include technologies such as vibration mills (Palla®Mill), stirred media mills (Vertimill®), vertical roller mills (Loesche) and high-pressure grinding rolls (HPGR) (Jankovic, 2015). This study preliminary investigated the mineral processing of a low-grade, ultra-fine-grained, complex iron ore in a laboratory scale after dry grinding by HPGR to 90% < 25 µm without consideration of the grinding, milling, energy and classification cost."

Jan 1, 2018

By Li-ming Qi

During mining, the stress in the coal face varies, and, at the same time, the gas flows from the coal body into the excavation, which will cause the gas pressure to change continuously. Assuming the coal gas content of the coal to be constant, and applying the law of energy conservation, the influence of stress concentration on the gas pressure was analysed. It was found that the stress is proportional to the gas pressure. Finally, as a result of analysis and the law of gas flow, the gas pressure dynamic distribution ahead of tunnelling was modelled, and the mechanism by which blasting induces outburst was explained by making use of the model. Keywords: gas pressure, stress concentration, excavation, tunnel.

Jan 1, 2007

By Zhenyang Wang, Xingle Liu, Xiangdong Xing, Shan Ren, Hongen Xie, Jianliang Zhang

"Non-isothermal combustion experiments of different additive amount of bituminous (0, 20, 40, 60, 80, 100 wt%) were conducted by synthesized thermogravimetry analyzer(STA409PC) from room temperature to 900°C in air. The changes of combustion characteristic parameters o f pulverized coals in different atmospheres are analyzed. The results show that DTG curves of coal combustion move to low temperature zones when the amount of bituminous increases. It indicates that both ignition and burnout temperature are lower, burnout time decreases, combustion characteristic index obviously increases, and combustion performance of blending coal are improved. The iso-conversional method involving Kissinger-Akah-Sunose (KAS) method was used for the kinetic analysis of the main combustion process. The results indicated that, when the additive amount of bituminous varied from 0 to 100 wt%, the value of activation energy which would sharply reduce if the additive amount of bituminous was under 60% increased from 133.94 kJ•mol-1 to 78.03 kJ•mol-1by using KAS method.IntroductionPulverized coal injection (PCI) to blast furnace (BF) is an important way for saving energy and reducing resource consumption during the ironmaking process. In order to acquire higher coal injection quantity, the relevant research topics in the field of pulverized coal combustion technology such as enhancing the efficiency of pulverized coal combustion, improving the combustion characteristics and reducing the harmful gas emissions and so on received extensive attention in recent years [1,2]. The combustion of blending coal when the appropriate proportion is selected for coal and also mixed well- distributed could give full play to the advantages of various types to make up the defects of single coal which is widely used throughout the world. So the blending coal injection to BF could produce a good impact on safety and economy for productive process. Therefore, a large amount of experimental researches on the combustion characteristic of blending coal for anthracite and bituminous were carried out by experts and scholars around the world [2-7].Nevertheless, the systematic research on the combustion behavior of anthracite with different content of bitumite in a thermogravimetric analyzer (TGA) is less. So in this paper, using the method of multiple scanning rate of conversion method, bituminous to promote the pulverized coal combustion reaction was studied to analyze its promotion mechanism of pulverized coal combustion reaction process, and the kinetic parameters of activation energy was also calculated, which to provide theoretical basis for the rationalization of resource utilization."

Jan 1, 2014

By Jing Lin, Yuan Xu, Qingcai Liu, Dengfu Cheng

"Smelting reduction technology has been developed greatly in recent years. But one of the key problems for this technology is about the refractory that used as lining material in the molten bath. Investigation and test shown that corrosion rate of refractory was much higher and the corrosion mechanism was much more complexity in the molten bath of smelting reduction with iron bath than that of the blast furnace and rotary furnace technology [l-5]. The corrosion behavior and corrosion rate of Al2OrC-ZrO2 series refractory in the melt of smelting reduction with iron bath have been studied by rotary immersion and quasi-static immersion test in this paper. The major factors that affect the interaction between the melt and refractory were investigated. The test results shown that the corrosion rate of AI2O 3-C-ZrO2 series refractory decreased with the ZrO2 increasing when ZrO2 content was from 3% to 10%. Ferrous oxides content, relative moving speed between the melt and refractory and temperature of the molten bath were the important factors that affect the corrosion rate. But the ferrous oxides concentration was the most important one. The corrosion rate was increased as a linear relation with the rising of ferrous oxides content of the melt. The corrosion rate in the quasi-static immersion was much less than that of the dynamic immersion (rotary immersion) for the Al2O 3-CZrO2 series refractory in the same testing condition. The corrosion mechanism of Al2OrC-ZrO2 series refractory is: graphite oxidized in advance, then interaction between the constituents of refractory and melt taken place and deteriorate layer of refractory and new compounds were formed, the properties of refractory was changed.IntroductionSmelting reduction with iron bath is a typical technology [3, 4, 6]. The obvious features of the melt for smelting reduction technology with iron bath are much higher ferrous oxides and much more complexity melt composition and structure than that of the blast furnace technology [2, 5-8]. The properties of the melt were changed dynamicilly and constantly in reduction process. On the other hand, the behavior of the melt depends on the activity and the reduction rate of ferrous oxides in the molten bath[9]. Because of the high concentration of ferrous oxides in slag and high reduction rate in the molten bath, the corrosion behavior and corrosion mechanism of the refractory lining by melt are an important factor in development of the technology of smelting reduction with iron bath. Up to now, improving refractory quality to anti-corrosion of melt and developing high quality and long term refractory used as the lining refractory materials in the molten bath of the final reduction furnace are also the most important questions for developing smelting reduction technology."

Jan 1, 2000

By M Camarda, A Pirson, F Vasconcelos, J Mesquita

ArcelorMittal Prijedor is a goethitic iron ore mine located in the north-west of Bosnia and Herzegovina, which mainly supplies ArcelorMittal’s European subsidiaries. Annual production of the asset stands at the level of 1.5–2.1 million tons of iron ore product which is sent to ArcelorMittal Zenica steelmaking plant. Two types of products with approximately 50 per cent Fe are generated in Prijedor through a process composed by crushing, screening, and magnetic separation stages. Within this process one of the tailings produced is called ‘ultrafines’. The ‘ultrafines’ product corresponds to the desliming hydrocyclones overflow in Prijedor plant, which is classified in a size fraction below 25 μm and corresponds to about 5 per cent of feed. This material is richer in iron than the coarser size fractions of the ore but do not present a good performance in concentration processes. In this way, several studies have been carried out during the last years to find solutions to use the ‘ultrafines’ material without success. In this context, the possibility of dehydroxylate the goethite contained in the material transforming the mineral into hematite and thus increasing the iron grade of the final product was investigated. During the research, several dehydroxylation tests with different temperatures and time of exposure were performed. Using dihydroxylation process at temperatures higher than 800°C it was possible to produce a material with 43 per cent Fe from the original 39 per cent Fe ‘ultrafines’ sample. In addition, the dehydroxylation tests confirmed that goethite becomes completely transformed into hematite at 400°C (with an exposure time of 60 mins) and material is completely sintered at 1200°C. A simulation study based on dehydroxylation tests results showed that it would be possible to use a ‘ultrafines’ product with Fe grade higher than 45 per cent to produce a material with 50 per cent Fe through a complete dehydroxylation process.

Sep 18, 2023

By Tiejun Chun, Jian Pan, Deqing Zhu, Zhiyong Ruan

"In this paper, the desulfuration of pyrite cinder pellets was carried out. Phase analysis shows that most sulfur of pyrite cinder exists in the form of elementary sulfur. Most sulfur was removed in preheating stage. 81.25% sulfur was removed and the average SO2 concentration of exhaust gas was 1365ppm when the pellets were preheated at 950oC for 9 min. The final product, assaying 62.42wt%Fe and 0.02wt%S content at 96.88% desulfuration was achieved under the conditions of preheating at 950? for 9 min and roasting at 1200? for 15 min, which can be used as the burden for blast furnace.IntroductionPyrite cinder, as a subsidiary product of sulfuric acid production by roasting of pyrite ores, was solid waste in sulfuric acid enterprises. According to the statistics, the annual production of pyrite cinder is about 15 million tons in China. Besides, there is lots of pyrite cinder deposited for many years [1-3]. The pyrite cinder consumed in the cement and other industries as auxiliary additives only accounts for less 30% of its total discharge and the left is stored in waste pond, occupying much land and polluting environment in China [4-5]. Moreover, pyrite cinder contains iron between 30-63% which can be utilized as a cheap raw material for ironmaking by sintering or pelletizing processes, which can not only prevent pollution but also provide cheap raw materials for ironmaking [6-7]. However, compared to traditional iron ore concentrate, pyrite cinder possesses higher sulfur content."

Jan 1, 2012

Study on the Effects and Mechanics of Na2SO3 to Chalcopyrite and Galena

Sep 13, 2010

For the past four years, the Department of Mining Engineering at the University of Kentucky has conducted a validation study of the CFD Fluent code, by comparing its results against mining-related benchmark experimental data provided by NIOSH?s Pittsburgh Research Laboratory. This particular study is dedicated to the effect of machine-mounted dust scrubbers on the performance of face ventilation systems using extended-cut mining with a blowing curtain.

Jan 1, 2009

By Lu Lin, Yanping Bao, Xiang Li, Linzhu Wang, Xiaobai Yan

The results showed the microinclusions were mainly Al2O3 and sulfide inclusions from tapping to the beginning of LF refining. Al2O3 inclusions were modificated into calcium aluminates after calcium treatment. Lots of spherical calcium aluminates composite inclusions containing MgO, TiO2 and MnS were found after soft blowing and during tundish metallurgy and left in the slab which caused the defects of beam plates. Pure Al2O3 inclusions were observed again after soft blowing 8min. Average sulfur content in inclusions decreased because of the high desulfurization ability of refining slag. Average Ca/Al ratio value in inclusions increased during LF refinging because of the reduction of CaO in slag by carbon and it increased obviously during the process of soft blowing 8min because of the dissolusion of calcium wire.

Jan 1, 2015

By B. K. Choi, S. H. Kang, G. E. Kim, K. B. Kim, S. Noh, T. K. Kim, H. J. Jin

Oxide dispersion strengthened (ODS) steel is being considered as an in-core structural material of future nuclear reactor systems because of its excellent creep and irradiation resistance on the basis of uniformly distributed nano-oxide particles with a high density, which is extremely stable at high temperature in a ferritic/martensitic matrix. Up to now, ODS steels have been intensively studied and developed to apply these materials to the in-core structural component of future nuclear systems. The primary activity is to develop high strength advanced ODS steel, fabrication technology for the structural components and key joining technology for the component fabrication. As a result, a Fe-10Cr-1Mo alloy with a superior creep resistance at high temperatures has been developed. An optimized fabrication process of this alloy system has been established through various process conditions in mechanical alloying, hot/cold working, and heat treatment processes. Joining technology for the ODS steel components is also being developed using solid-state welding such as magnetic pulse welding, friction stir welding and diffusion boding. These R&D activities will contribute to the realization of ODS materials for future nuclear reactor system applications.

Jan 1, 2015

By Longjiang Li, Mao Jiang, Zhihui Shen, Guizhou University, Yin Pan

This paper aims to study the influence and action mechanism of collector Y-89 on the flotation of auriferous pyrite. The measurement to identify adsorption quantity, IR and XPS spectrum analysis and flotation experiment made on the pure mineral were conducted. The research results show that when the dosage of MIBC is 20 mg/L, and pH of 8, the dosage of Y-89 over 60 mg/L, the pyrite recovery rate is greater than 80%.And when the dosage of Y-89is 60 mg/L, dosage of MIBC 20 mg/L, the pH in a wider range (pH=4~9), the recovery is greater than 75%. When the pH is above 10, the pyrite is depressed and its recovery rate is found to be dramatically dropping. Adsorption quantity measurement also shows that the strong alkaline conditions inhibit the adsorption of Y-89 on the surface of auriferous pyrite. IR measurement indicates that chemisorption of Y-89 occurs on the surface of auriferous pyrite. XPS spectrum analysis indicates that without adding Y-89, oxidation reaction occurs on the surface of pyrite. But when Y-89 is added, the chemical environment of Fe on the surface of pyrite has changed. Such findings indicate that with Y-89, chemisorption occurs on the surface of auriferous pyrite.

Jan 1, 2014

By Yiming Zhang, Yunpeng Li, Chun Feng, Ruyang Cao

In the past, the selection of the number of empty holes between blast holes heavily relied on the subjective experience of practitioners, leading to unsatisfactory blasting results. The number of empty holes between blast holes is particularly important for the perforation of explosive cracks. In order to determine the optimum number of empty holes for inducing the propagation of explosive cracks, a two-dimensional numerical model of two-hole blasting was established based on the continuous-discontinuous element method (CDEM) using polymethyl methacrylate (PMMA) as the medium, and numerical simulation of various working conditions was conducted; the simulation results are basically consistent with the PMMA model test. Through the analysis of blasting parameters, the optimal number of empty holes with a certain hole spacing is fitted. The following conclusions are drawn: (1) There is a threshold for variable x. When x exceeds 50, the presence of empty holes cannot lead to the perforation of explosive cracks between the blast holes. (2) When x is below 50, the optimal number of empty holes inducing the propagation of explosive cracks can be determined through fitting an empirical formula. By adjusting the number of empty holes between blast holes, a significant spacing between adjacent blast holes was achieved, allowing for effective penetration, so as to effectively “induce” the direction of the fracture zone and make full use of the energy of explosives. The research results of this paper are conducive to the research of directional blasting technology and provide certain references for the optimization of precision blasting parameters.

Dec 19, 2023

By Lou Gaozhong, Guo Wenbing, Zhao Gaobo, Wang Shuren

"The height of a fractured zone due to high-intensity mining (HIM) plays a vital role in the safety analysis of coal mining under bodies of water. This paper described the characteristics of HIM. The processes of overburden failure transfer (OFT) are analyzed. The state of destruction transfers from a certain stratum to the upper stratum as face advance distance increases, and the processes of OFT are divided into two stages: transmission development stage and transmission termination stage. Through theoretical analysis, the limited suspension-distance and limited overhanging distance of each stratum are proposed to judge the damage of each layer. Based on this, the OFT criteria of fractured zone development are obtained. The mechanical model of strata suspended integrity and overhanging stability are established. Finally, a new method to predict the height of fractured zone due to HIM is put forward based on the processes of OFT, the limited suspension-distance, and the limited overhanging distance. Further, a HIM panel in the Datong coal mine is taken as an example. Theoretical methods are proposed, and engineering analogy is used to predict the height of the fractured zone, which is compared with in-situ measurements reported in the literature. The results show that the in-situ measurements for the height of the fractured zone are in close agreement with the theoretical calculation result. Therefore, the rationality and reliability of the theoretical method proposed to predict the height of fractured zone is verified.INTRODUCTIONThe height of the fractured zone (HFZ) due to the exploitation of coal is a key parameter for the safety analysis of coal mining under a body of water (Wenbing, Youfeng, and Hou, 2012). Accordingly, it is necessary to predict HFZ under the corresponding mining conditions before coal mining."

Jan 1, 2018

By X Yang, B Wang, L Liu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Huoqiu iron ore field in north-west Anhui province is located in the south-east margin of the North China Craton and hosts large iron resources. Orebodies are hosted in Neoarchean amphibolite facies metamorphic rocks, forming silicon-iron bands from north to south. The area is dominated by an Early Precambrian basement consisting of Neoarchean grey gneisses, amphibolites and metasediments. The gneisses are similar with assemblages of Trondhjemite-Tonalite-Granodiorite in compositions and intercalated with amphibolites. Igneous zircons from gneisses and amphibolites have U-Pb ages of 2.86 and 2.75 Ga respectively, which are interpreted as the crystallisation ages of their protolith. Zircons from amphibolite and gneiss have eHf(t) values of 2.4–15.5 and -3.0–1.5 respectively. The tDM2(Hf) model ages of the gneiss range from 2.87 to 3.14 Ga, which is consistent with tDM1(Hf) ages of amphibolite (2.84–3.16 Ga). The U-Pb-Hf isotopes thus confirm that the gneisses were generated by partial melting of amphibolite. Two granites produce two group Hf isotopic compositions. The older one (1916 ± 42 Ma) has eHf(t) values and tDM1(Hf) ages of -9.4–3.4 and 2.24–2.71 Ga respectively, whereas the younger one (1823 ± 41 Ma) shows a large variation in eHf(t) values of -18.1–12.5 and tDM1(Hf) model ages of 1.73–2.92 Ga. Geological and geochemical characteristics indicate that the Huoqiu banded iron formations are a Superior-type iron formation rather than an Algoma-type as previously considered.CITATION:Yang, X, Liu, L and Wang, B, 2015. Study on the Huoqiu banded iron formation, West Anhui Province, East China , in Proceedings PACRIM 2015 Congress, pp 649–656 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015