Search Documents

By M. Orchin

THIS PAPER is concerned with two aspects of the behavior of coal: (1) Dispersion by solvents atmospheric pressure and high temperature and (2) the destruction and regeneration of the coking properties of coal. Several pure polycyclic compounds and a coal-tar fraction were found to extract 95 percent of the organic material of a bituminous coal. About 20 percent of the extract was soluble in benzene, and this fraction contained the ?coking principle? of the coal. From an extensive chemical spectroscopic, and x-ray study of the benzene-soluble material, some conclusions could be drawn concerning the composition and structure of this fraction of coal. A possible commercial application of the extraction technique is in the preparation of low-ash carbonaceous material for the manufacture of electrode carbon.

Jan 1, 1951

By J. L. Yordan, J. Kortmeyer, I. Yildirim

Talc is used to remove stickies from pulp during paper recycling processes. It is well known that the interaction is controlled by the surface chemistry at the talc/water, sticky/water and talc/sticky interfaces. If the interfacial tensions are known, one can calculate the free energies of interaction and hence predict whether the stickies can be removed by talc. In the present work, the surface tensions of several different talc samples were determined using the acid/base theory. The information was then used to determine appropriate interfacial tensions, which in turn were used to determine the free energy of interaction between talc and stickies. It was found that the calculated free energies are much more negative than those between the stickies and other minerals such as calcium carbonate, bentonite clay and kaolin clays.

Jan 1, 2002

By R. D. Brittain

In order to analyze and control the transport of harmful trace-element impurities in various smelting processes, it is necessary to have fundamental information about the chemical thermodynamic properties of the pertinent condensed and vapor phases. This paper describes recent thermodynamic studies of the gaseous arsenic sulfides and of the activity of arsenic in a copper-iron sulfide matte phase. These studies were carried out by high temperature mass spectrometry and by effusion vaporization techniques, which permitted clear identification of the molecular species involved, a decided advantage in such complex systems. The nature of the results obtained and comparisons with previous interpretations will be described.

Jan 1, 1983

Gold is actively precipitating at grades up to 80 g/tonne at and near the surface of the Waiotapu geothermal system, located in the Taupo Volcanic Zone of New Zealand. Many characteristics of this active system makes it analogous to the environment deduced for epithermal precious metal mineralisation in the circum Pacific region.The near surface area of the geothermal system is approximately 17 km2, caused to an extent by the upflow of deep, neutral pH fluids being deflected into a lateral flow of several km. This fluid has pervasively altered the rhyolite pyroclastic and ash deposits to an assemblage generally characterised by the term propylitic; major vein mineralisation is not observed. The temperatures at the 1100 m limit of drilling are 300¦C, and decrease to the surface along a boiling point curve.Condensation of steam and H S (subsequently oxidised) at the surface (derived 2from deep boiling) results in the formation of heated acid sulphate waters. These have caused a shallow (50 m) cap of advanced argillic alteration. Mixing of this oxidised condensate with the deep neutral pH fluid appears to be the principle cause of gold deposition from thiosulphide complexes. The major focus of gold mineralisation is in Champagne Pool, a hot spring which fills one of several 900 year old hydrothermal eruption craters.

Jan 1, 1984

By Yongbin Yang, Meixia Cai, Yufeng Guo, Guanzhou Qiu, Tao Jiang, Jianjun Fan

"A series of sintering and metallurgical experiments were carried out to optimize the blast furnace burden structure in this study. The results indicated that the sinter disintegrated seriously with basicity around 1.4, and after this “turning point”, the sintering properties were improved gradually with the increase of basicity of sinter. Based on the results, an idea was put forward which focused on producing two different kinds of sinter with different basicity. Different with the original burden structure of 85% sinter with basicity 1.4-1.5 + 15% pellets, an alternative new BF burden structure was proposed by the following structure?44% sinter with basicity 1.05 + 44% sinter with basicity 1.87 + 12% pellets. This new alternative BF burden structure has been adopted by some steel plants.IntroductionIn recent years, conventional blast furnace (BF) process was put into operation to produce hot metal in “A” steel plant. “A” steel plant owns two sets of sinter strands at present. Because the sinter production capacity exceeds the actual requirements of BF, a burden structure with 85-90% self-made sinter + 10-15% purchased pellets is adopted to take advantage of the low–cost sinter. But the serious problems encountered with the BF operators are that the sinter disintegrated easily during transportation and storage process. Therefore, the rate of return fines is very high after sinter being screened."

Jan 1, 2012

By Anand Anupam

Conventionally, beneficiation in Indian coal washeries is done using dense medium cyclones upto the size of 0.5 mm. Coal fines below 0.5 mm size are extensively cleaned by froth flotation. There are many problems associated with flotation of Indian coals, e.g. poor response of coal particles to flotation, misplacement of fine high-ash material to froth, loss of good quality coarser coals (within ?0.5 mm size range) to tailing streams, high cost of reagents, water contamination, etc. In addition, sophisticated control systems for efficient management of the fines washing circuits are needed. Thus, there is an escalation in the capital and processing costs. In view of these facts, studies were carried out to establish the cleaning potential of dense medium cyclones for beneficiation of fine coal down to a size of 0.1 mm, essentially aimed at reducing the load on fine coal circuits mainly comprising of flotation. ROM Coal (in the size range of -2 + 0.1 mm) obtained from JogtaOCM,Jharia coalfield possessing relatively low ash (about 21%) was used in this study. Purpose for using low ash coal was to further lower, its ash content down to 8% which is comparable, to the ash content of imported coal. After characterization studies, nine tests were carried out on the prepared feed sample for its beneficiation using a dense medium cyclone of non-conventional design (very low cone angle and longer barrel), by varying its apex and vortex finder diameters. The efficiency of separation has been evaluated using Tromp curves. It could be established that it is possible to produce a clean coal of 8% ash, with Ep value of 0.044, using Jogta OCM coal by treating it in a modified dense medium cyclone. These results are summarized and discussed in detail in the present paper. Keywords: dense medium, cyclone, fine coal, beneficiation, Jharia coal

Sep 1, 2012

By H. Kiyama

In order to further elucidate the mechanisms involved in autogenous grinding, the fracture of rock specimens in free-fall impact was studied using the theory of elasticity. Stress distributions in rock specimens under various conditions of impact were analyzed and the conditions for failure were examined in relation to the compressive and tensile strength of rock. The energy equation derived for autogenous grinding coincides basically with Lewis' generalized formula or Oka and Majima's formula, and it is sufficiently general to incorporate all of the three older theories, viz; those of Rittinger, Bond and Kick.

Jan 1, 1972

By Azizan A

The paper presents the results of chlorination of beneficiated rutile and struverite (a tantalum-niobium bearing, rutile type mineral in alluvial tin deposits) by carbon tetrachloride in the range 623¦K to 773¦K. The chlorination of rutile could reach near completion at 773¦K in about an hour. The process was found to follow a modified pore-blocking law, with the basic reaction constant K varying inversely with the particle size, so that the basic process may be a reaction under interface control (chemical control) as modified by the pore blocking effect. The pore blocking factors for the various experimental conditions were evaluated and the predicted curves showed good agreement with the experimental data. In the case of Struverite, a similar kinetic behaviour was observed but the chlorination process was relatively slower than that in rutile. It was also observed that in struverite, niobium got chlorinated faster, followed by tantalum and titanium, indicating a good possibility of separation by chlorination using carbon tetrachloride.

Jan 1, 1996

By Zhigeng Xu

Pressure leach of a Yunnan marmatite concentrates with adding coal as the elemental sulfur disperser was investigated. The experimental results show that the coal with carbon content higher than 70% is incapable of dispersing elemental sulfur from minerals and cannot improve the leaching of zinc. The coal with low carbon content (lignite coal) can act as excellent sulfur-disperser in the pressure leaching at 423K. The mechanism of lignite coal as sulfur disperser was further discussed by ultraviolet, infra-red spectrum and mass spectrum.

Jan 1, 2008

By Ma Yuxin, Niu Fusheng, Yuan Zhitao, Bai Limei, Han Yuexin

"Using batch flotation experiment, contact angle measurement, particle size analysis, and scanning electron microscope (SEM), the influence and difference of pH value on the flotation rate of talc and chalcopyrite were investigate without collector at the pH range of 3~11. The results showed that, the flotation rate of talc decrease with the increasing of flotation time, while that of chalcopyrite hardly affect by flotation time, besides, the flotation rate of chalcopyrite is much less than that of talc, so the laws of flotation rate of the two minerals are independent of pH value. The flotation test data of two minerals are simulated with first order and multi-rate flotation kinetic model respectively. The simulation results showed that flotation of talc only meet the first order kinetic model, while chalcopyrite’s meet the both. In addition, According to test results of talc and chalcopyrite by the particle size distribution, SEM photographs and the contact angle measurement, the reason why talc did not conform to the first order kinetic model is not because of particle size distribution, but of particle shape. That is to say, because of sheet structure of talc, the contact angle of layers and sections are 74°and 52°respectively. At the same time, the contact angle of layers and sections are different between the particles. So flotation rates between talc particles are difference.INTRODUCTIONPossessing superior self-induced, collector-induced and sulfur-induced floatability, chalcopyrite exhibits good floatability at a wide range of pH values and potentials. Serpentine are regarded as the most difficult selected type in various chalcopyrite ore, and the predominant reason is that it contains talc. Talc, as a nonpolar layered silicate mineral, is one kind of common associated mineral in sulfide ores (Lu, 2010). Concentrate quality and flotation process of chalcopyrite are influenced as a result from the presence of talc. It is because that talc has inherent floatability which makes it readily mixed with the floated mineral and talc is easy to slime causing the slime coating of the valuable mineral (Beattie et al., 2006). Thus in order to improve the flotation effect of chalcopyrite, methods can be introduced from two respects. One method is that fast-floating talc mineral is floated preferentially, and the other is that sulfide mineral is floated prior to talc by depressing the flotation of talc mineral (Beattie et al., 2006), nevertheless, no matter with which the flotation effect of fine-sized chalcopyrite is not positive. Therefore, in order to realize the flotation separation of talc and chalcopyrite, the difference between the inherent floatability of fine-sized chalcopyrite and talc is researched and analyzed in terms of flotation dynamics in the absence of collector and frother."

Jan 1, 2016

By Liu Q, Siefken T. C, Misra V. N

Investigation of the differential flotation characteristics between arsenopyrite and pyrite in a ore concentrate have been carried out on a laboratory Leeds flotation cell. Experimental results indicate that some limited separation between arsenopyrite and pyrite is possible by differential flotation under the conditions of high pH and low pulp redox potential. The best performance in this testwork was achieved by using an oxidizing agent at pH 10.7. Of the oxidizing agents tested, NaOCI gave better oxidizing effect than KMnO4. It has also been observed that the pulp redox potential depends on the pulp pH value. At high pH values a hydroxide layer is formed on the arsenopyrite surface, which has the effect of a depressant on the arsenopyrite.

Jan 1, 1992

By M. Okido, W. Wei, L. Chai

The kinetics on the growth of Thiobacillus ferrooxidans was studied by use of series piezoelectric quartz crystal ( SPQC ). Arsenic ioninhibits the growth of Thiobacillus ferrooxidans, which is consistent with the previous results by other measuring method. This further demonstrates that the SPQC can monitor the chemical activity of the growth of Thiobacillus ferrooxidans. Cupric ion accelerates the growth of Thiobacillus ferrooxidans. The mechanism was discussed, it was considered that copper promotes the protein enzyme of Thiobacillus ferrooxidans, rustic yanin, to form over the range of cupric ion concentration studied. There action order of cupric ion in accelerating the bacterial growth is 0.067. The growth of Thiobacillus ferrooxidans is dependent on temperature, the apparent reaction activation energy decreases from25.56 kJ / mol to 18.32 kJ / mol because of the addition of 10 mg / L Cu(II) to the bacterial growth solution of pH 2.0 at initial inoculum of 10%.

Jan 1, 2000

By Akerkar D. D, Dey M. L, Mathur S. B, Chowdhury S. K R

The extraction of gold and silver from chalcopyrite concentrates has been investigated. In view of the recent interest in non-cyanide leachants for gold and silver, one such alternative reagent, namely thiourea, has been employed in the present work. Precious metal leaching was attempted from received copper concentrates as well as pre-oxidised concentrates. Pre-oxidation of the concentrates was carried out by three different methods, namely roasting, pressure oxidation and biological oxidation. After pre-oxidation and leaching of the base metals, the leach residues were subjected to further leaching for precious metal extraction. The results obtained on the extraction of gold and silver from received concentrates as well as pre-oxidised concentrates are presented and the effectiveness of the three pre-oxidation routes employed is compared.

Jan 1, 1992

By G. P. Karmakar, K. K. Chandan

"The drilling mud is an essential part of the drilling process, which plays a major role in keeping safe and efficient oil and gas well drilling. In the oil industry, bentonite clay dissolved in water produces the simplest type of drilling muds. Bentonite clay contains montmorillonite particles. These particles are dispersed uniformly in water and such dispersions are used in various industrial products like paints, ceramics, pesticides and drilling muds. The bentonite clay easily dissolves in water and increases the viscosity of the water, which is one of the most important properties of a drilling mud. Bentonite has the highest swelling capacity, which is responsible for building up of the viscosity of the clay-water system. The flocculation behavior of bentonite is one of the major concerns for the performance of the water-based drilling mud in the oil and gas well drilling process. The behavior of drilling mud greatly depends upon the quality and quantity of bentonite clay, as well as the additives that are used in their formulations. In this work, a comprehensive study has been carried out to find out the effect of added polyacrylamide (PAM) polymer, surfactant, pH and salt concentrations on the dispersion/ flocculation characteristics of bentonite clay-water system. It has been observed that the increase in PAM dosage reduces the residual turbidity and improves the settling rate of the bentonite particles. The flocculation rate has also been found to be better under higher pH conditions. The combined effect of salt concentration and PAM dosage improved the overall flocculation efficiency of the system.INTRODUCTIONIn the oil industry, bentonite clay dissolved in water produces simplest type of drilling muds. Bentonite clay containes montmorillonite particles. These particles are dispersed uniformly in water. Such dispersions are used in various industrial products like paints, ceramics, pesticides and drilling muds (Akther et al., 2007). The bentonite clay easily hydrates in water and increases the viscosity of the mud system (Razi et al., 2013; Meng et al., 2012). Bentonite clay in the drilling mud increases the viscosity which is one of the most important prop erties of a drilling mud. Bentonite has the highest swelling capacity, which is responsible for the building up viscosity of the clay-water system (Sonmez et al., 2013). The drilling mud is an essential part of the drilling process, which plays a major role in keeping a safe and efficient oil or gas well drilling (ASME, S. S. C., 2005). The flocculation behavior of bentonite is one of the major concerns for the performance of the water-based drilling mud in the oil or gas well drilling process. This behavior of drilling muds greatly depend upon the quality and quantity of bentonite clay, as well as the additives that are used in their formulations (Yu and Amanullah, 2005; Akther et al., 2007). Bentonite particles form aggregate under certain conditions including high temperature, and high concentration (Luckham and Rossi, 1999). If the quality of bentonite is not sufficient to accomplish intended viscosity of the muds, it is essential to add certain additives to increase the viscosity and prevent aggregation of the system (Razi et al., 2013). The anionic polymer bearing sample can build up inter-particle bonds between the polymer and clay particles. The addition of various additives like, polymers control the dispersion and enhance the viscosity of the mud by controlling the flocculation of montmorillonite particles in bentonite dispersion (Heller and Keren, 2002; Mahto and Sharma, 2004)."

Jan 1, 2018

By L. Zhang, Y. Zhou, H. Wang, C. Mo

Fluorination of magnetite (Fe₃O₄) by NH₄HF₂ was investigated using simultaneous thermogravimetry and differential thermal analysis (TG-DTA), and observing the morphology and phase changes using scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDS) and X-ray diffractometry (XRD). The results indicate that fluorination with the involvement of oxygen begins at room temperature, peaks at 178.40C, and is completed at 2000C with the formation of only (NH₄)₃FeF₆. On heating, (NH₄)₃FeF₆ gradually releases NH₄F by the formation of NH₄FeF₄ at 2590C, then (NH₄)0.18FeF₃ at 3270C, and finally FeF₃ with minor FeF₂ at 4000C due to the partial reduction of Fe (III) to Fe (II). At 5500C, FeF₃ is oxidized to FeOF/Fe₂O₃.

Dec 13, 2022

By M. Sahoo, P. Burke, Y. Fasoyinu, J. P. Thomson

The effects of grain refinement, mold temperature and chemical composition on the hot tearing resistance of aluminum alloys 535.0 and 206.0 has been studied by pouring constrained rod castings in metal molds. In addition, two prototype components that could be used in automotive applications were also poured from both alloys by gravity tilt-pour and low pressure permanent mold casting processes. This paper summarizes the results and issues encountered during the casting trials. It was shown that grain refinement and mold temperature ::::: 400°C reduced, and sometimes eliminated hot tear cracks in both alloys. The two prototype engineering components could be cast successfully from both alloys in metal molds. The metallurgical issues related to molten metal treatment and processing temperatures were well controlled. However, issues related to the control of hot tearing, casting and mold design must be addressed in future studies to guarantee the production of defect free castings.

Jan 1, 2006

By D. S. Salonine

Aluminum alloys offer a wide range of capability with a unique combination of advantages that makes them the materials of choice for numerous products and markets. One of the most important applications is their use as the primary structure and outer envelope in aerospace vehicles. Wide and thorough studies on hot working and microstructure evolution of aluminum alloys have been made in Russia. The most important appear to be: - introducing the structure diagrams in strain rate - temperature coordinates which show areas of different microstructures (non-recrystallized, recrystallized, and mixed) after the hot deformation and the following heat-treatment for common aluminum alloys (Yu.M. Vainblat); - studying the press-effect ("structural effect" by V.I. Dobatkin); - learning the influence of hot worked substructure on aging mechanisms; conducting researches on press heat-treatment. These works allowed a deeper understanding and a better control of the mechanical behavior of aluminum products. Comparisons are made to equivalent developments in Europe and America.

Jan 1, 2004

By V. G. Grechanyuk

The paper presents the mechanical properties of Cu-Mo composite materials depending on the molybdenum content. The influence of structural defects on the mechanical-physical properties of the condensates at stretching testing as well as of the lamellar grain dimensions upon the mechanical properties of Cu-Mo composite materials is also presented.

Jan 1, 2008

By U. B. Kodukula

The iron ore beneficiation plant at Serra-Azul Mines of ArcelorMittal, Brazil operates at a rated capacity of 3.2 million tons per year. The ore is concentrated using magnetic separation, jigging, hydrocyclones and spiral concentrators. The tailings from the process plant are generated from classifier overflow of 135 tons per hour dry solids and thickener underflow of 48 tons per hour dry solids. A systematic experimental program was carried out using Multi-gravity separator (MGS), and wet high-intensity magnetic separator (WHIMS) for recovering the iron values from both of the tailing streams while minimizing the total quantity of tailings to be discarded. The classifier overflow contained 32.3 percent iron, 49.9 percent silica and 2.18 percent alumina and was 45 percent finer than 45 microns in size. The thickener underflow sample contained 47.3 percent iron, 27.6 percent silica and 2.49 percent alumina and was 16 percent finer than 45 microns in size. Separation results on the classifier overflow sample with the MGS indicated that a concentrate containing 62.1 percent of iron, 10.8 percent silica and 0.36 percent alumina can be achieved with a weight recovery of 24.5 percent. The results with WHIMS at 6500 Gauss indicated that concentrate containing 62.6 percent iron, 8.3 percent silica, and 0.65 percent alumina can be achieved at a weight recovery of 34.7 percent. 4.7 percent. WHIMS studies at 6500 Gauss on thickener underflow sample indicated that a concentrate containing 61.4 percent iron, 8.8 percent silica, and 1.74 percent alumina can be achieved at a weight recovery of 57.2 percent. Based on these results, and further in-house test works, a WHIMS installation was adopted for the recovery of iron values from the tailings in the operating plant at ArcelorMittal Serra Azul Mines, Brazil.

Feb 23, 2014

By A Bagchi, Nabiullah, Jagdieh

"A number of coal mines in India are affected by fire. Most of coking coal reserves in the country are located in Jharia coalfield where more than 18 sq. km is in the grip of fire. Generally such fires are confined in areas near to our crops. About 37 million tonnes of coking coal are lost in recent yearsdue to fire and another 48 million tonnes are blocked in fire areas. Preventive measures adopted to control fires were only partially successful and the cost of such measures was exorbitant I Temperature of blast holes in fire area varies between 60 and 300° C or even more. Even after thorough quenching of holes with water, it become difficult to bring down the temperature below SO"" C. For blasting hot holes primary need is to select safe and suitable commercial explosives and detonating fuse and to measure hot hole temperatures. VWiOUs types of commercially available explosives including Nitro Glycerine bare, slurries, site mixed slurries (SMS), emulsion5 ,detonating fuses and detonators were tested to determine their thermal behaviour at elevated temperatures under field simulated conditions in the Copyright © 2000 International Society of Explosives Engineers 1993g - Studies on Safe Blasting Technique in Fire Area of Coal Mines laboratory and in hot blast holes in field . More than 50 round of blast were conducted in fire areas. NG base compositions and detonators were found unsafe at temperature above SO0 C andtherefore, they are not permitted to be used in hot holes. Slurries and emulsion are stable upto 1200 c. For blasting at temperature exceeding SO0 C a heat resistant gel/ solution was developed by the authors and is being used in number of fire areas."

Jan 1, 1993