Search Documents

By S. K. Kawatra, S. J. Ripke

Iron ore concentrates pellets are currently in duration heat hardened (sintered) under oxidizing conditions. Pellets produced from magnetite ore concentrate are completely oxidized during induration and finish as hematite pellets. These pellets then require a blast furnace to reduce the hematite to metallic pig iron. Partially reduced pellets would save energy and fuel during transportation and further reduction. It has been stated in the literature “the most important single factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of the magnetite to hematite and the subsequent recrystallization and grain growth of this constituent.” However experiments shown in this paper reveal that oxidation is not necessary to produce high-strength pellets. Magnetite concentrate pellets developed similar strength when indurated at 1350°C under either oxidizing (air) or inert (argon) atmosphere; the pellets sintered under argon remained magnetite. In addition, magnetite concentrate pellets indurated under reducing (CO) atmosphere also remained as magnetite, but required induration temperature of approximately 150°C less than the other pellets.

Jan 1, 2003

By M. F. Almeida

"Due to the randomness of all factors influencing the sintering operation, a two-stepped procedure is proposed to find the best way of using stocked fines at a plant producing Fe-Mn alloys for the steelmaking industry. The approach is based on the following: (1) predict the result of the sintering operation by establishing the best multilinear regression model using some of the characteristics of the loaded material; and (2) find the best solution under a minimizing cost criteria by solving a linear optimization problem using the regression equation plus constraints on the feed and product. IntroductionSome tests carried out using 20% to 30% of sinter in the material loaded into a 60 000 KVA Tysland-Hole electric furnace producing Fe-Mn alloys for the steelmaking industry indicated: (1) a meaningful decrease in the off-gas temperature and, consequently, a better energy use due to the material higher porosity; (2) more uniform heat distribution as a consequence of the electrode reaction zone enlargement; (3) an improved furnace control resulting in a smoother operation; and (4) a decrease in gas production facilitating the off-gas treatment. For some years, this plant used only the coarse fraction of the Mn ores, thus stocking all the received and own-generated fine particles. In view of the mentioned results, a strategy for increasing the use of stocked fines was formulated, including a step where it was necessary to decide which components and respective quantities should be used in the blends to be sintered (Almeida, 1984).It is well known that several factors affect productivity and energy consumption in sinter production, also influencing the product quality. Raw materials characteristics, namely chemical and size composition, affect permeability to gases and may or may not allow a deeper bed. In general, finer ores decrease permeability, increasing electricity consumption by fans, but due to their higher specific surface area, react more completely with other components in the mixture. For coke granulometry, a compromise must be obtained in order not to burn it too quickly nor to widen the flame front, therefore decreasing productivity. Decreasing coke in the blend also acts in sinter bonding, decreasing its consistency and increasing crushing and return fines. Moisture addition also influences components mixing, pre-agglomeration, bed permeability and, consequently, sintering productivity. Therefore, optimum conditions must be established for both a given sintering plant and the components in the feed (Dawson, 1993)."

Jan 1, 1998

By De-qing Zhu, Feng Zhang, Jian Pan

Sintering performance of a series of sinter blends with high ratio of limonite was investigated. The metallurgical performance and mineralogy of product sinter were also examined. The results show that good sintering performance could be obtained when the ratio of limonite was below 43% in the blends of iron ore fines, while good microstructure and metallurgical properties were achieved under optimum sintering conditions. In contrast, sintering performance will rapidly deteriorate when the ratio of limonite is elevated up to 63% in the blends.

Mar 1, 2017

By Cheng Pan, Qiugang Yuan, Xuewei Lv, Mei Liu, Enguang Guo

Land-based nickel resources include nickel sulfide and nickel laterite. With the consumption of high grade nickel sulfide, use of nickel laterite has received more and more attention. The mineralogy and sintering behavior of limonitic nickel laterite with high iron and low nickel and silica was studied to offer technical support for producing ferronickel through sintering–blast furnace route. The mineralogy results showed that the main phases in this kind of nickel laterite are goethite (FeO(OH)), gibbsite (Al(OH)3) and NiFe2O4. The TGA (Thermogravimetric Analysis) and DSC (Differential Scanning Calorimetry) revealed hydroxide minerals in addition to absorbed water. After the sintering experiments the chemical composition, phases present (XRD analysis) and physical properties of the sinter were studied. The content of FeO in the sinter increased with increasing basicity up to 1.3, and then decreased with further increase in basicity. The yield of sinter increased (from 73% to 80%) with increase in the basicity from 1.1 to 1.7, and then the yield decreased with the further increase in basicity. Mg(Ni)(Fe,Al)2O4 is the main phase in the sinter while MgCaSiO4 and Fe2SiO4 is the main binder phase when the basicity is 1.1~1.5, and MgCaSiO4, Fe2SiO4 and SFCA is the main binder phase when the basicity is 1.7~2.1.

Jan 1, 2014

By Donghai Li, Cheng Pan, Pan Chen, Xuewei Lv, Mei Liu

"Chromite concentrate after beneficiation can not be directly used in the electric furnace. Therefore sintering is one of the effective way to agglomeration, by which the chromite concentrate can be utilized and the power cost of ferrochrome smelting can be reduced. The properties of raw materials and the sintering process of chromite concentrate were studied in this work. The results showed that chromite concentrate used can hardly granulated alone, while chlorite addition can improve the effect of granulation. Moisture plays an important role in sintering process. The granulation effect is optimal when the amount of water addition is 12%. Strength and abrasion index are the evaluation indexes of sinter quality. It was found that the strength of sinter increased with coke dosage increasing to 12%, and then decreased when it continuously increased. Opposite regularities were found for the abrasion index of the sinter.1 IntroductionChromium is a very important metal element which is mostly used in the production of stainless steel. In the earth, it is always formed compound with iron as ferrochromium spinel (FeO.Cr203), and its mineralogical name is chromite.[1] Currently, the global production of chrome ore is about 20 million tonnage every year , in which fine ore (less than 8 mm) accounted for about 80% [2] Although the price of the fine ore is cheaper than the lump one, too much fines will lead to the poor permeability and causes increased electricity consumption while producing ferrochrome. Therefore, the agglomeration process of chrome ore is one of the effective measures to increase the usage ratio of fine ore."

Jan 1, 2013

By Donghai Li, Cheng Pan, Xuewei Lv, Mei Liu, Enguang Guo

"Phosphorite is the main raw material for the production of phosphorus in chemical industry. More attentions have been drawn to the phosphorite concentrate beneficiated from low-grade phosphorite due to the decrease of high-grade phosphorite. For another, the agglomeration process is necessary for the phosphorite concentrate after beneficiation process. The mineralogy and sintering process of the phosphorite from Leshan, China were studied in this work. The result shows that the main phases in the phosphorite are fluorapatite (Ca3(P04)3F), hydroxylapatite (Cas(P04)3(0H)), quartz (Si02) and dolomite (CaMg(C03)2). The yield of the sinter increases with increasing the carbon dosage to 7%, and then decreases when it continuously increases. Similar regularities were found for the strength and the content of P20s of the sinter. The best strength of the sinter as well as its P205 content were discovered when the carbon dosage is 7%. Fluorapatite ((Ca5(P04)3)F) is the main phase in the sinter while fuggerite (Ca2MgSiz01) is the main binder phase.IntroductionPhosphorus is an important foundation industrial raw material of national defense industry, food industry and chemical industry, where it is used to produce red phosphorus, phosphonium hydroxide, phosphorus pentasulfide and phosphoric anhydride[l-2]."

Jan 1, 2013

By B. M. England, C. Y. Yang, L. T. Matthews, J. Y. Yin

The domestic concentrate used by the Shanghai Meishan Metallurgical Corporation in Nanjing contains significant siderite, magnetite and haematite, the siderite having a substantial influence on its sintering behaviour. On the basis of experimental findings and published information it is proposed that siderite decomposition starts at c.400 degrees C and results in the formation of CO and/or H2, which then reduces the haematite to magnetite prior to the initiation of high-temperature sintering; inter-mixed particles of Australian haematite and pisolite ores also undergo significant reduction. As the gaseous reduction process is so effective, low-temperature forms of silico-ferrite of Ca and Al (SFCA) cannot form even at high sinter basicity. The bench-scale results were confirmed in a pilot-scale facility whose sinters consisted mainly of magnetite, high-temperature SFCA and glass, which is typical of sinters formed from mixes with high magnetite levels

Aug 1, 1995

By Sibin Zhang, Shengli Wu, Youhao Yin, Yuandong Pei, Zhixing Zhao, Jiangshan Shi, Zhengyun Fan

Spraying medium to achieve an energy-saving and emission reduction for iron ore sintering has been researched, such as spraying natural gas, coke oven gas, oxygen, sintering flue gas and gas from annular cooler. This paper focuses on effect of spraying steam on sintering surface on reduction of NOx and dioxin emissions in practical sintering production in Shougang Jingtang. It can be found that, with the increase of sintering bed spraying steam amount, NOx and dioxin of flue gas showed a decreasing trend. As spraying steam 1 t/h for 550 m2 sintering machine in Jingtang, NOx content decreases 2.6–9.5 mg/Nm3, and dioxin decreases 0.007–0.014 TEG ng/Nm3.

Mar 1, 2018

By H Han, L Lu

Due to the international depletion of reserves of traditional high-grade iron ore, the ore resources available throughout the world, especially in steel mills in East Asia, have changed drastically from hard hematitic to more goethitic ore types, such as pisolitic and Marra Mamba ores. The level of impurities and loss on ignition in iron ore has also been slowly increasing. Finally, the proportion of fine material in the available products has increased considerably for most iron ore fines. This has been found to have significant impacts on sinter quality and sintering performance. Magnetite concentrate is typically high in Fe grade and releases extra heat when oxidised to hematite. The amount of magnetite concentrates is expected to increase due to the recent development of a number of magnetite projects. Some of these magnetite concentrates will end in sinter blends. This will not only improve the sinter quality and but also have a beneficial impact on the fuel consumption of the sintering process. However, most of the concentrates available are very fine, which will negatively impact the green bed permeability and consequently the productivity of the sintering process. This paper reviews and comments on the recent technological advances in sintering with high proportions of magnetite concentrates.CITATION:Han, H and Lu, L, 2017. Sintering technologies of sinter mixtures containing high proportions of magnetite concentrates, in Proceedings Iron Ore 2017, pp 31–38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Guilherme Santos Garcia

Este trabalho tem por objetivo avaliar a sinterização a plasma do alumínio com a utilização da técnica Active Screen, em comparação com o processo em forno resistivo. Foi utilizado pó de alumínio atomizado, com granulometria entre 30 e 100µm, sendo misturado junto aos pós cerca de 1% em massa de estearato de zinco como agente lubrificante. Foram confeccionados corpos de prova com 13mm de diâmetro e 10mm de altura. A compressão dos pós se deu através de uma prensa hidráulica, de ação simples, utilizando pressão de compactação de 600MPa. O tempo te sinterização foi mantido em 60min a temperatura de 500ºC, utilizando atmosfera de nitrogênio. Foram realizadas medidas de densificação, antes e após a sinterização, medição de rugosidade e microdureza superficial, bem como análises em MEV da superfície das amostras. O processo a plasma se mostrou satisfatório, sendo capaz de produzir amostras com boa densificação. As medições de microdureza superficial evidenciaram valores semelhantes entre os processos, sendo a amostra sinterizada via plasma a apresentar menor variação de microdureza. Através da análise de EDS das imagens, foi identificada a presença de estearato de zinco em ambos os processos, evidenciado que a extração do lubrificante não foi totalmente eficaz. Ainda, houve uma leve redução da rugosidade no processo a plasma em relação ao convencional.

Aug 17, 2017

By Mariane Abreu Alves Campos

A utilização do wBN como ferramenta de usinagem pode eliminar a necessidade de retífica das peças. Portanto, neste trabalho, os experimentos realizados tiveram por objetivo o estudo e caracterização de compósitos à base de wBN, diboreto de titânio (TiB2) e alumínio (Al) para obtenção de pastilhas para usinagem. A composição utilizada para a investigação utilizou 70% de wBN. Os compósitos foram obtidos sob altas pressões e altas temperaturas via aplicação cíclica . As patilhas atingiram aproximadamente 4,5 mm de diâmetro, e altura de 4,0 mm. As amostras foram caracterizadas por ensaio de dureza Vickers, microscopia eletrônica de varredura, microscopia confocal e densidade. De forma geral, os melhores resultados foram para amostras com ciclos de um minuto cada, para os três ciclos, sendo pouco dependente do valor da pressão aplicada. Foi observada dureza maior que 17GPa, baixa porosidade e um valor de densidade aparente muito próxima à teórica.

Aug 16, 2017

By Cheung L. C C, Maconochie A. P

SIROFRAG is a computer-based imaging system that quantifies the post-blast rock fragment size distribution in a muckpile in a mine environment. Improvements in blast performance and blast modelling are being hampered by a lack of a quick and objective method to evaluate the major result of the blast: the fragment size distribution. This is usually done by hand digitising muckpile photographs: a labour intensive and tedious process. SIROFRAG is being developed to quickly, cheaply and objectively provide this information. SIROFRAG is based on active stereo image analysis. It uses a light stripe to illuminate a muckpile and a pair of video cameras to determine the 3D nature of the scanned objects. The imaging system is based on a novel prototype scanning projector that allows images to he captured in full daylight. The Microsoft Windows based software controls the projector and interprets the captured images to provide a size distribution of exposed rock fragments.

Jan 1, 1995

By Nilmani M, Malone J, Taylor RN, Floyd JM, Gray NB, Fountain CR

CSIRO staff and University of Melbourne staff and students collaborated in an intense programme of investigation on the CSIRO 50 kg Sirosmelt pilot plant.In two days of operation copper matte converting and zinc slag fuming trials were performed, whilst investigation of the process dynamics and process chemistry was carried out. This exercise is an example of the techniques available for process evaluation, which can rapidly advance the understanding of pyrometallurgical operations by use of a team approach covering a wide range of experiments.

Jan 1, 1985

By John W. Korczak

The use of geological and grade block models has been standard practice in mine design for many years now, with a wide range of software available for creation and analysis. Although geotechnical parameters are of vital importance to mine planning there is very little in the way of commercially available systems for integrating geotechnical data into the mine planning and design process. Sirovision is a new technology developed by the CSIRO (Commonwealth Scientific and Industrial Research Organization) in Australia for automated, safe and accurate 3D mapping of geological and geotechnical features. Datamine has integrated this capability into its product range so that Sirovision has become an integral part of the day-to-day mapping, mine geology and geological / geotechnical modeling in both open pit and underground mine environments. This is the first integrated underground application of Sirovision from Datamine collaboration with Xstrata Nickel at the Nickel Rim South Project. This paper discusses the role of Sirovision in collecting the raw data required for geological and geotechnical analysis and the interpretation in a quick, safe, auditable and reproducible manner.

May 1, 2009

By H. C. Van Der Merwe

In the 21st century, dynamic, accurate digital 3-D geological models are essential to the pursuit of safe, efficient and profitable mining. This is particularly true for the deep-level underground mines in South Africa. The Sirovision® solution is a collaboration project between the Australian CSIRO (Commonwealth Scientific and Industrial Research Organisation), Datamine Software Ltd. and AngloGold Ashanti Ltd (AGA). The purpose of the project is to provide a fully integrated digital rock face imaging, geological mapping and modelling system for the AGA gold mining operations. The CSIRO-developed Sirovision® Stereo Camera Rig (SCR) consists of two digital cameras, alighting system, a laser guidance system and image processing software. The imaging system works on the principles of photogrammetry, i.e. overlaying of two 2-D images with a central focus point, with mathematical algorithms extracting 3-D information from the 2-D image pair. The output from matching several image pairs is a computer-generated, full 3-D, virtual copy of the mining excavation. The image resolution and relief ares of sufficient quality to distinguish different rock types and structural contacts. Functionality within Datamine Studio3 is used to add geological intelligence to the 3-D images provided by Sirovision®. The geologist identifies and ?draws? lines representing geological features directly onto the image. By utilizing the inherent ?topography? of the 3-D image, the software is able to convert the lines into 3-D surfaces, ready for use in the 3-D geological model. Subsequent to promising underground test results from AGA?s Sunrise Dam Gold Mine (SDGM) in Australia and other mining operations worldwide, it was decided to test the Sirovision® system in the South African deep-level gold mines. The first underground tests at Moab Khotsong Mine began in January 2009. The objectives of these tests entailed the capturing of 3-D images of selected development ends, mapping of geological features onto the 3-D images and integration of the mapping data with the 3-D geological model. Some downsides have cropped up during the feasibility testing, related to practicality of the SCR for acquisition of 3-Dimagery in the deep-level underground operating environment. These constraints will have to be addressed prior to operational implementation. Facing such difficulties is not unusual when attempting to implement new technology in such a challenging working environment and testwork is still in progress at the mine in order to prove the concept of using this technology in a Witwatersrand underground gold mine. The great advantage of the Sirovision® solution is that it offers the geologist the opportunity to work remotely on a 3-D virtual copy of a mining excavation, without the heat, humidity, hazards and time constraints associated with physical mapping in an underground workplace.

Jan 1, 2009

By Roger Ferreira da Silva

O método de ensaio não destrutivo baseado na análise do ruído magnético Barkhausen (RMB) possibilita a obtenção de informações a respeito da microestrutura do material examinado e do estado de tensões presente no mesmo. Devido às particularidades do método, as medições devem ser realizadas mantendo-se constante a geometria entre a sonda e o objeto examinado, de forma a assegurar a confiabilidade das mesmas. Quando realizado manualmente, o processo de medição é demorado e sujeito a erros de posicionamento da sonda. Em trabalhos industriais ou em laboratório, esses erros podem resultar em interpretações incorretas, devendo ser reduzidos ao mínimo possível. Visando à redução do tempo de execução das medições e de análise e a eliminação de possíveis erros de posicionamento da sonda de inspeção, este trabalho propõe a automação do processo de medição de RMB em corpos de prova do tipo chapa. Compreende a construção de um dispositivo de movimentação XYZ acionado por motores de passo e do software “Plate Barkhausen”, com uma interface amigável, para controle da movimentação e da medição, além da análise dos dados.

Jul 30, 2018

By Antônio César Freitas, Lucas Machado Barbosa de Faria

Este trabalho descreve o funcionamento do sistema automático desenvolvido para realizar o posicionamento de vagões durante a troca de rodeiros, que opera no Centro de Troca de Rodeiros – CTR, localizado nas instalações da empresa Vale em São Luís do Maranhão. O posicionamento de composições com até 110 vagões e com precisão de centímetros, resguardando a folgas entre vagões, é um desafio na rotina de manutenção. Para superar esse desafio foi desenvolvido um sistema automático para posicionar as composições de vagões, que utiliza medição baseada em tecnologia laser, com precisão de centímetros, e que atualiza continuamente a distância entre um rodeiro e o ponto correto de parada, possibilitando assim o posicionamento de rodeiros.

Oct 1, 2019

By Artur Augusto Martins

Este trabalho tem como objetivo apresentar o projeto de uma plataforma de cloud computing onde profissionais de diversos segmentos da metrologia, calibração, instrumentação e controle poderão cooperar entre si no desenvolvimento de metodologias de medição, análise numérica e automação. A plataforma permite o modelamento matemático e o estudo analítico e/ou numérico de processos utilizando recursos disponíveis de cloud computing e a apresentação dos resultados e geração de relatórios através de uma interface web. Através do desenvolvimento cooperativo de novos procedimentos para análise de dados, modelos de instrumentos e melhorias operacionais do sistema pretende-se que o mesmo aproxime-se cada vez mais de um LIMS totalmente funcional e que tenha maior aderência à norma ISO/IEC 17025.

Jul 30, 2018

By Manuel Caro

El presente trabajo describe el proceso de mantenimiento del equipo de aire denominado Optiair. Este filtro al tener una mayor capacidad de retención de polvo, permite que el equipo pueda trabajar por periodos más largos sin tener que detenerse para realizar el cambio de filtros, lo cual incrementa el factor de disponibilidad del equipo. Entre los beneficios principales tenemos: el incremento de salida de aire, menor restricción del flujo, menor caída de presión y una mayor cantidad de contaminante capturado.

Aug 25, 2002

By Ricardo Huancaya

El sistema de apoyo a la gestión de flota de vehículos en mina a tajo abierto “GO Tracking”, es un sistema que permite la localización y rastreo de vehículos mediante el uso de la tecnología GPS". En ese sentido, el presente texto señala la implementación de estrategias de producción dirigidas a aumentar la eficiencia y disponibilidad de la flota en su conjunto. El proyecto fue gestionado siguiendo las directrices propuestas por el PMI, donde los riesgos de seguridad son mitigados mediante el monitoreo y alerta de exceso de velocidad, así como la proximidad de otros vehículos, evitando las colisiones.

Oct 21, 2015