Search Documents

By L. Cheng

This report presents the results of a Bureau of Mines laboratory investigation of the effect of water sprays in reducing respirable dust that escaped the face area of a full-scale wooden model of a mine en-try containing a wooden model of a ripper-type continuous mining machine and exhaust brattice. Areas examined were (a) the general effectiveness of a low-pressure water spray system mounted on top of the mining machine boom, a high-pressure spray system mounted under the boom, and the combined top-and bottom-spray systems, and (b) the effect of these three spray systems on the capture of coal dust particles of different sizes. Dust was injected into a sump cavity at the face. Airborne respirable dust concentration was mea-sured behind the brattice with a personal sampler and cyclone, and particle size distribution was mea-sured with a cascade impactor. When used alone, the top-spray system captured about 55 pct of the respirable dust in the face area and the bottom-spray system captured 60 pct; the capture efficiency of each system is decreased when they are used simultaneously. From a mass-concentration viewpoint, each spray system preferentially captures larger dust particles.

Jan 1, 1988

By B. D. Hanson

An interactive computer program has been developed by the Bureau of Mines which enables the user to identify the effect of cutting system changes on relative dust generation for longwall shearer drums. The program simultaneously evaluates machine and coal seam parameters, and those parameters which the user can control. The user can change one or more of these parameters at a time to determine their effect on relative dust generation, cutting forces, and/or cost. The program is written in the BASIC programming language. A complete program listing is included along with user instructions and sample outputs. This program is a more comprehensive version of the relative dustiness index (REDI) program described in Bureau Report of Investigations 8979.

Jan 1, 1988

By A. M. Stubbs

The Bureau of Mines has devised a procedure to selectively extract and recover chromic oxide (Cr203) from waste high-temperature shift catalysts that contain approximately 6 pct Cr and 62 pct Fe, both in oxide form. The Bureau's procedure consists of roasting the waste catalyst with sodium hydroxide (NaOH) or sodium carbonate (Na2C03) followed by water leaching. The chromium from the leach liquor was recovered utilizing an oxidation-reduction reaction with pH adjustment to form a hydrous chromic oxide (Crp3oXHp) precipitate. The roast-leach procedure produced chromium extractions greater than 89.7 pct, with product recovery in excess of 99 pct from the leach liquor. The costs of the NaOH and Na2C03 roast processes, including sizing and equipment-related recommendations, were determined by the Bureau's Office of Process Evaluation. The economic evaluation indicates that producing a Crp3 product, at the present time, is not competitive with the present-day cost of imported chromites. The estimated average operating cost for both processes was $5.44/1b of recovered Cr203 concentrate. However, this procedure offers a potential alternative to the disposal of this waste through landfiIl.

Jan 1, 1988

By Paul W. Jeran

Subsidence over a series of longwall panels undermining sloping terrain in southwestern Pennsylvania was monitored to verify the Bureau of Mines subsidence prediction model for the northern Appalachian coal region. Comparison of the field data to model output shows close agreement. Vertical movements over each panel ceased with the mining of the adjacent panel. Horizontal movements were significantly affected by topographic slope. The distribution of horizontal strains over each panel were similar, with a zone of compression occurring over the center of each panel. The zones of compression were flanked by zones of tension toward the rib. The magnitude of the tensions were affected by the slope. The strains developed at the completion of each panel were not significantly altered by the mining of subsequent panels.

Jan 1, 1988

By D. Ng

A facility to evaluate the fire endurance of mine stoppings was constructed by the Bureau of Mines in the multiple entry section of the Bruceton (PA) Experimental Mine. Stoppings up to 6 by 18 ft can be tested in a manner simulating mine conditions. The stopping is subjected to a 70-min liquid fuel tray fire with an energy output of 75,000 Btu/min. The stopping and adjacent areas are instrumented with thermocouples and heat flux gauges. Data acquisition is by an automatic data logger capable of continuously recording over 100 channels of information. Two 8-in-thick concrete block stoppings and a galvanized steel stopping were tested. A crack developed on the fire side surface of the block stoppings where the flames were most intense. However, the temperatures of the unexposed surfaces of the stoppings never exceeded 800 C and the surfaces were undamaged. The steel stopping retained its structural integrity during the test. The temperature of the unexposed steel surface reached 5000 C, but combustible materials located 1 ft from the surface did not ignite. A 3/4-in-thick coating of construction plaster was applied to the fire side of the previously tested uncoated steel stopping. The quantity of heat energy transmitted across this coated metal stopping was reduced approximately 50%. All stoppings prevented the passage of flame and smoke.

Jan 1, 1988

As part of the Bureau of Mines program to reduce U.S. reliance on foreign suppliers of strategic and critical metals, research was conducted to improve technology for the recovery of critical metals from hardface alloy grinding waste, a form of superalloy scrap. This report describes a hydrometallurgical process that demonstrated on a laboratory scale that 79 pct of the chromium, 97 pct of the cobalt, 99 pct of the manganese, 99 pct of the nickel, and 90 pct of the tungsten could be recovered in chemical form from hardface alloy grinding waste. The process involved deoiling the grinding waste, followed by chloride-based dissolution of the deoiled material. A high-grade calcium tungstate (CaW04) product was recovered from the resultant leach residue by caustic leaching and precipitation. Iron, cobalt, man-ganese, and nickel chlorides were sequentially recovered from the leach liquor by solvent extraction. Amine extractants were used to extract the iron, cobalt, and manganese; decanal oxime was used to extract the nickel. Market-grade cobalt chloride (CoCI2), manganese chloride (MnC12), and nickel chloride (NiCl2) products could be produced directly from the resultant strip liquors. The final raffrnate was a relatively pure chromic chloride (CrCI3) solution that compared favorably with commercial solutions.

Jan 1, 1988

By J. I. Paige

The effect of fluoride inclusions on the properties of titanium produced from the Bureau of Mines-developed induction slag melting process is of concern to the titanium industry. The objective of the research was to determine the effect of removing the nonconductive molten calcium fluoride (CaF2) slag used as an insulator between the titanium and the segmented copper crucible. The data were obtained from single-induction-melted ingots prepared with no CaF2 insulating slag and an ingot prepared with the normal addition of 4 pct CaP2 slag. The results showed that the mechanical properties of single-induction-slag-melted and annealed Ti-6AI-4V alloy exceed the minimum values specified in "Aerospace Materials Specification for Titanium Alloy Bars and Forgings AMS4928H." High-cycle, tension-tension fatigue testing yielded similar results. The data from 44 of the 45 specimens were contained within the typical scatter band for fatigue data on wrought Ti-6AI-4V alloy. Although the removal of the insulating slag is a desirable change, the data from the specimens with the previously standard 4 pct slag addition showed no detrimental effect from the slag inclusions.

Jan 1, 1988

By Russell E. Griffen

With the development of larger mine-haulage trucks in recent years, the visual field of the driver has diminished correspondingly. Specifically, the operator's lack of direct vision in the right front area and directly to the rear constitutes a serious hazard to personnel in nearby small utility vehicles. Recently developed electronic technology has made it possible to supplement the use of mirrors and fresnel lenses to warn the operator of specific collision dangers in the truck's blind areas. This Bureau of Mines report describes the results of a coordinated contract and in-house research program to develop and test in-mine prototype electronic systems to detect the presence of smaller vehicles within the blind areas of large mine-haulage trucks. Each system utilized transmitters installed on the smaller vehicles and receivers installed on the haulage trucks. Transmitting techniques tested included both low-and high-frequency radio waves. On-vehicle testing established the engineering feasibility of each approach. Further private sector product development to improve reliability and reduce system costs is recommended. Mining companies should consider the advantages of each type of system.

Jan 1, 1988

By J. E. Allison

As part of a Bureau of Mines research program to conserve critical and strategic metals, an aqueous electrodeposition method for preparing stainless-steel-type coatings was studied. Chromium powder (averaging 3 J1.m diam) was suspended in a ferrous-nickelous sulfate electroplating bath and occluded in the electrodeposited Fe-Ni alloy matrix. Subsequent heat treatment of the resulting composite coating formed the ternary alloy. The occlusion process was affected by the quantity of Cr powder suspended in the electrolyte and by the microstructure and composition of the electrodeposited matrix. Coatings containing up to 21 wt pct Cr were deposited from an electrolyte containing 20 vol pct suspended Cr powder. Heat treatment at 1,100° C for 8 h homogenized the composite coating. Deposition of 44Fe36Ni20Cr alloy coatings (250 J1.m thick) on AISI 1020 carbon steel rods, followed by heat treatment, provided complete protection of the carbon steel during exposure to a boiling 65-pct-HN03 solution. Corrosion rates of 0.6±OA mm/yr for the coating in the boiling HN03 approximate that of 304 stainless steel. Practically shaped electroforms have been prepared by the coating method.

Jan 1, 1989

By W. K. Tolley

The Bureau of Mines is testing super critical fluids as solvents to selectively extract valuable components from complex matrices. Materials recovered during supercritical fluid extraction are often highly purified. Using laboratory apparatus designed specifically for supercritical fluid research, Bureau re-searchers have measured the solubility of titanium tetrachloride (TiCI4) in supercritical, liquid, and gaseous carbon dioxide (C02), CO2, a commonly used supercritical fluid, is inert, inexpensive, and nontoxic. Supercritical CO2 formed a single phase with TiCl4 at 45° C and 1,500 psig. When the solution was heated at constant pressure beyond 55° C, TiCl4 precipitated from the fluid. Results showed that TiCl4 solubility in supercritical CO2 is not controlled by the vapor pressure of the solute.

Jan 1, 1989

By M. R. Yenchek

The Bureau of Mines conducted research to determine the relationship between cur-rent load and temperature rises in coal mine trailing cables. Six low-voltage, unshielded, portable power cables were continuously and intermittently loaded with direct current of various magnitudes. Temperature rises within and on the cables were measured with thermocouples, and the data were recorded with a computer. Thermal time constants were calculated, which fixed the periods of the duty-cycle tests. Relationships between average temperature at the conductor-insulation interface and current load were established. The steady-state and intermittent currents that produce a 90° C average conductor-insulation temperature were then determined. Comparisons with Insulated Cable Engineers Association (ICE A) steady-state ratings revealed that 10 to 25 pct more current than recommended ICEA ampacities is required to reach rated insulation temperature. Examination of the maximum intermittent temperatures attained showed that autoignition of coal dust and burn injuries to personnel handling the cable would not be concerns if the temperature at the conductor-insulation interface averaged 90° C.

Jan 1, 1988

By Thomas M. Barczak

This Bureau of Mines report investigates shield mechanics by describing the elastic response and interaction of shield components to applied vertical and horizontal displacements for various canopy and base contact configurations. This research provides information on generalized shield mechanics, which is applicable in describing the behavior of all two-leg shield supports. Utilizing mechanics of materials concepts and known kinematic relationships for two-leg shield supports, free-body diagrams are constructed for each shield component illustrating internal axial, shear, and bending moment responses required to maintain equilibrium for each load case evaluated. Predicted shield (component) responses are verified by controlled displacement of instrumented longwall shields in the Bureau's mine roof simulator (MRS). Conclusions drawn from these analyses include shield structural responses are significantly dependent upon canopy and base contact configurations. Applied displacements also significantly affect shield responses. Horizontal displacement produces different responses than those produced by vertical displacements. The direction of horizontal displacement is also significant in evaluating shield response. Applications of shield mechanics to in situ support monitoring are also discussed. An objective of this research program is to establish unique shield responses to identify in situ load conditions.

Jan 1, 1989

By C. A. Rhoades

The spillage that accumulates under conveyor belt lines presents a possible fire and explosion hazard fomiinqjetsoruiel, especially to those who must clean up the spillage. The U.S. Bureau of Mines conducted research to reduce this hazard by identifying and investigating the parameters affecting the efficiency of conveyor belt cleaning. The amount of material carried back under the conveyor and the wear rates of metal cleaning blades decreased with increasing blade-to-belt pressure to a limiting value, after which the carryback and wear rates remained essentially constant. The optimum blade-to-belt pressure was found to be 11 to 14 psi for the research conveyor system. Greater pressures increased the blade-belt friction without improving either cleaning or blade life. The modes of blade wear were three-body abrasion and slurry erosion caused by the sand-lime test mixture. Wear rates were reduced by increasing the metal hardness, opti-mizing the pressure, and removing conveyor belt imperfections. Corrosion was not observed to affect the wear of various steels in tests of less than 34 h. The results of this study should allow mine operators to run their conveyors under conditions that will maximize cleaning and minimize equipment wear.

Jan 1, 1989

By L. J. Froisland

The U.S. Bureau of Mines conducted laboratory studies on sulfuric acid (H2S04) digestion of alunite [KA13(S04)2(OH)6] as a means for treating domestic deposits of this mineral. Digesting alunite ore in boiling H2S04 at concentrations of 88-wt-pct acid or higher breaks down the alunite and permits a convenient separation of potassium and aluminum. The digestion reaction is a complex sulfation reaction occurring in two stages. In this reaction, the potassium component extracts into the H2S04 for eventual recovery as potassium sulfate k2s04 in a separate unit operation. Aluminum is left as acid-insoluble aluminum sulfate [A12(S04)a], which can be extracted by a 95° C water leach. Additional purification of AI2(S04)a produced in this study is needed to meet cell-grade alumina (Al202) purity specifications. Extraction and separation of potassium and aluminum from the alunite ore were consistently above 90 pct.

Jan 1, 1989

By J. Drew Potts

The U.S. Bureau of Mines identified respirable dust sources and controls on four continuous auger mining sections, two with relatively low dust levels and two with high levels. Factors adversely affecting dust levels included auger equipment design, continuous haulage, and low seam height. Dust controls included ventilation practices and spray systems. Maximizing airflow seemed to reduce dust levels most. Air leakage and shock loss can be reduced by constructing stoppings with brushed-on mortar containing fiberglass and by keeping areas between curtains and ribs free from obstructions and storing equipment not essential for face activities in outby crosscuts. Curtain configuration, setback distance, and installation can also affect dust levels. Use of both blowing and exhausting curtains is the most effective configuration. Setbacks from the face should not exceed 15 ft. Installing brattice curtains at least 5.5 ft from ribs, when entries are 26 ft wide, minimizes velocity head. Installing curtains tightly against the mine roof and floor helps maintain a forward airflow movement in the center of the mine heading; curtain overlap can create a tighter seal. The wet-auger spray system also effectively controls dust, provided the mine is already exercising good ventilation practices.

Jan 1, 1989

By Jeffrey S. Walker

The purpose of this U.S. Bureau of Mines effort was to determine if ground movement caused by mining-induced subsidence is directly transferred to a structure and, if so, how that transfer takes place. Four concrete block walls with foundations were constructed and monitored over an active longwall panel. Three of the walls were located perpendicular to the direction of mining in zones where maximum inclination, maximum tension, and maximum curvature were predicted to occur. The fourth wall was constructed along the centerline of the panel, parallel to the direction of mining. All of the walls and the surrounding ground surface were instrumented with conventional survey monitoring points and extensometer stations to observe the vertical and horizontal movements. The fourth wall instrumentation also included continuously recording tiltmeters. The results of this investigation indicate that these simple structures respond to subsidence in a similar manner as the ground surface. This suggests that once the transfer mechanism is more fully defined, prediction models can be developed to accurately estimate the effect of mining on surface structures.

Jan 1, 1989

By K. Y. Haramy

Coal mine bumps involve the violent, rapid failure of coal and rock around a mine excavation. Deep coal mines with strong roof and floor rocks and high-stress conditions frequently experience face and rib bumps. The bump problem is becoming more severe as mining depth increases, prompting efforts to control high stress in advance of mining. This Bureau of Mines report presents a review of the most widely used methods to detect and destress high-stress zones along coal faces and an investigation of stress-related bump problems and destressing techniques at a cooperating mine. Geotechnical instrumentation and microseismic methods were used to better understand bump occurrences in underground coal mines. Laboratory tests of the drilling-yield method for high-stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress at various confining pressures. A three-dimensional, multiple-seam computer modeling program, MULSIM, was used to evaluate the effectiveness of stress-relief methods. Modeling results indicate that dangerously high-stress areas can be controlled by either proper planning or destressing. Proper mine planning guidelines and destressing methods such as volley firing, hydraulic fracturing, and auger drilling are discussed.

Jan 1, 1988

By John E. Pahlman

The U.S. Bureau of Mines has continued its investigation of chemical additive drilling fluids that produce a zero surface charge (ZSC) on a rock to better define the boundary conditions of the phenomenon. Laboratory drilling tests were performed on Minnesota taconite, Tennessee marble, and Sioux Quartzite using diamond-impregnated coring bits or tungsten carbide spade bits. Drilling fluids were made from chemical additives such as inorganic salts, cationic surfactants, cationic polymers, acids, or nonionic polymers in either distilled, deionized water (DDIW), mine pond water, mine well water, or tap water. These additives were tested below, at, and above their respective ZSC concentrations. Penetration and bit life improvements obtained with ZSC concentration solutions ranged from 88 and 56 pct, respectively, to over 650 pct and over 400 pct, respectively, for the additives tested. Polyethylene oxide (PEO) was found to be the best additive for ZSC-controlled drilling because a continuous range of PEO solution concentrations produced the enhanced ZSC-controlled drilling performance.

Jan 1, 1989

By Larry A. Haas

The U.S. Bureau of Mines investigated the use of organic binders as substitutes for bentonite in agglomerating iron ore concentrate. Over 30 organic binders were evaluated at several dosage levels in laboratory tests. The binder groups producing the greatest green pellet strengths were natural gums (guars carboxyl methyl celluloses) and gelled starches. The nongelled and alkalized starches, starch acrylic copolymers) wood-related products, and dairy products were less effective but better than bentonite. The highest wet pellet drop numbers were obtained with binders that had a medium plate water absorption value (>500 and <10)000) in distilled water and a high slurry viscosity (>75 cP) at 6 pet solids. The highest dry compressive strengths were obtained with binders that gave the highest adhesive tensile strength (>4 kg/ cm2) on iron oxide lap-joint substrates. Pellets with 0.1 pct organic binder had lower compressive strengths and reduction disintegration indices than those with 1 pct bentonite, but higher reduction rates. Pellets with carboxyl methyl cellulose and gelled starch had higher softening temperatures than those with bentonite. Overall, the most promising binder is gelled starch. Its price makes it more cost effective than carboxyl methyl cellulose, and its pellets have metallurgical properties superior to those of bentonite pellets.

Jan 1, 1989

By M. P. Board

The U.S. Bureau of Mines, under a cooperative agreement with Hecla Mining Co., conducted a rock mechanics study at four widely spaced horizons in a deep mine shaft in northern Idaho. The objective of the project was to measure and analyze rock deformation and lining behavior during construction of a deep shaft in a high in situ stress field within an isotropic rock mass. Rock mass displacements were monitored with multiple-position borehole extensometers. Liner stress and strain were measured with concrete pressure cells and embedment strain gauges. This report discusses the general trends and magnitudes of data from the four test sites, and relates the data to a proposed anisotropic constitutive model for the rock mass. A design procedure is then outlined for specifications of liner thickness and support installation sequences for future shaft sinking.

Jan 1, 1989