Search Documents

By James P. Ulery, Frank E. Chase

Clay veins found in coal mines have caused numerous injuries and fatalities. These structures plague all phases of mining, including entry development, pillar recovery, and panel extraction. Clay veins also increase production costs and may disrupt or halt mining. These detrimental aspects have prompted the Bureau of Mines to investigate the physical characteristics of and roof instability problems associated with clay veins. This was accomplished by observing and mapping clay veins in surface and underground mines. The occurrence and origins of clay veins were also investigated to determine predictive capabilities. The investigators found that clay veins normally occur in more stable, less rapidly subsiding coal basins. Clay veins result when tensile stresses develop fissures which are later infilled. These fissures can be propagated by compactional processes and/or tectonic stresses active during and subsequent to coalification. The Bureau also found that associated faults, fractures, and slicken-side planes commonly parallel clay veins and disrupt the lateral continuity of the immediate and, sometimes, main roof. When clay veins parallel or subparallel the direction of face advance, the roof is segmented into cantilever beams, causing unstable conditions. Consequently, the strata on either side of the clay veins should be bolted and strapped together to form a beam.

Jan 1, 1987

By F. Garacia, J. Cervik

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of a discharge pipe. These measurements are erroneous and tend to be high by as much as 30 pct. The Bureau of Mines deter- mined method factors (correction factors) for anemometer measurements taken in this manner. Method factors for 4-, 6-, and 8-in (10.2-, 15.2-, and 20.3-cm) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By Maureen M. Foss

Underground coal mining is hazardous due to changing geological conditions. One geophysical method showing promise for in-seam hazard detection is ground-penetrating radar (GPR). The Bureau of Mines recently completed preliminary studies to demonstrate the feasibility of using GPR for in-seam hazard detection. Investigations included air and coal tests for the purpose of checking equipment accuracy, coal penetration, and other factors such as the effects of receiver orientation. Further investigations involved using both a short pulse and a new prototype synthetic-pulse system to locate a clay vein in a coal seam using trans-illumination. Data were gathered on multiple travel paths, and a back projection processing technique was then used to create a tomographic image using the calculated velocities. A computer model of the same coal seam was subsequently processed using the same tomographic tech-nique, and the results were compared with those of the actual data. Analysis of the tomographic images shows the presence of the clay vein, although its boundaries are unclear due to the tomography method used. Results of these preliminary studies show that GPR is feasible for use in in-seam hazard detection and point the direction that future research should take. A need has been shown for research involving more sophisticated tomography techniques, transmission studies on thicker coal seams, and reflection studies using the synthetic-pulse system.

Jan 1, 1987

By A. Sainato, S. J. Schatzel, D. M. Hyman, J. C. LaScola

The Bureau of Mines determined the gas contents of 135 oil shale samples obtained from approximately 630 ft of core drilling. Drilling was done within a projected mining zone of the Cathedral Sluffs Mine, located in the Piceance Basin of western Colorado. Methane contents were determined by the modified direct method, which can measure the volumes of several gases released from or reacted with mine rock without destructive sample treatment. Over the duration of the test, nitrogen was largely unreactive, CO2 increased slightly, oxygen decreased markedly, and methane increased more than the total increase of all contained gases. The gas volumes were normalized per unit sample mass and are given in cubic centimeters per gram. Common time irzdices for test duration of 3, 40, and 125 days were used to compare methane desorption among samples. The means of the sample populations for these indices were 0.0316, 0.114, and 0.195 cm3/g, respectively. These quantities are lower than those reported in a Bureau emissions study at the Horse Draw Mine in the Piceance Basin. Oil shale samples that were gas enriched beyond the mean methane contents frequently contained bitumens and pyrite.

Jan 1, 1987

By K. O. Bennington

The thermodynamic properties of two manganese silicates, pyroxmangite and fowlerite (zincian rhodonite), were experimentally determined by the Bureau of Mines. The standard enthalpies of formation were determined by hydrofluoric acid (HF) solution calorimetry, the low-temperature heat capacities by adiabatic calorimetry, and the high-temperature heat capacities by differential scanning calorimetry over the range 322 to 1,372 K. Data for the standard enthalpy of formation (AH298), the derived standard entropy (S298), and the standard Gibbs energy of formation (AGf 298) are as follows: Pyroxmangite [(Mn0.9554Cao,0446)(Si03)J- AHf298 319.668±0.46 kcal/mol AH298 (from oxides)... -7.215±0.11 kcal/mol 5295 23.785±0.048 cal/(mol'K) AGf298 -301.190±7.96 kcal/mol Fowlerite [(Mno.7o3Zno.0884Ca0.2086)(Sio3)]--AHf298 ?... -329.914±0.419 kcal/mol AH298 (from oxides)... -8.400±0.104 kcal/mol 5598 21.949±0.059 cal/(mol-K) AGf298 -310.716±7.99 kcal/mol These experimentally determined values were combined with data from the literature to calculate the Gibbs energies and equilibrium constants of formation over the temperature range of the measurements. Standard enthalpies, Gibbs energies, and equilibrium constants of formation are given as a function of temperature from both the elements and the constituent oxides.

Jan 1, 1987

By R. J. Matetic

The Bureau of Mines, as part of a program to improve mine planning and development, is currently investigating the effects of pillar load transfer, which can impact mining operations wi.thin a multiple-seam configuration. At two mine sites where such ground interactions were present, the Bureau performed a complete geological analysis and installed and monitored instrumentation to gather pertinent data on rock mechanics. Overburden depth varied dramatically in the vicinity of the study area and reached a maximum at the study site; innerburden thick-ness was less than a pillar width (40 to 4S ft); heaving was experienced in both mines where sandstone and/or shale floor units were observed; overlays of the mine layouts show pillars were not totally superpositioned; a maximum of S in of roof to floor convergence was measured; and pressure readings indicated pillar core loading only and increased to a maximum of 7,000 psig over instrument setting pressure.

Jan 1, 1987

By J. E. Fraley

Full-column anchored resin bolts were first used in underground mines in 1972. These bolts appear to improve support in many roof bolt applications, as indicated by the use of about 30 million resin bolts in 1980. In the mid-1970's, Bureau of Mines in-vestigators began looking for a substitute for resin because of its short supply and rapidly increasing price. The investigators selected accelerated gypsum plaster (CaSO. ·1/2H20), which becomes gypsum (CaSO.· 2H20) when mixed with water. Gypsum makes an effective alternate grout material because it hardens quickly, is readily available, and is inexpensive in comparison with other cementitious materials. The Bureau received a patent (U.s. patent 4,096,944) for a system combining water capsules (wax-encapsulated water) with plaster into cartridges resembling resin cartridges. This report presents the results of tests conducted by the Bureau on the plaster, the water capsules, and their combined use in cartridges. The tests were designed to determine how the gypsum-plaster water capsule bolting system performs and what happens in the hole while the bolt is being inserted through the cartridge. The test results indicate that water capsule plaster cartridges are a workable alternative to resin cartridges under normal or dry conditions.

Jan 1, 1987

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation's mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987

By Keith S. Olson

During 1982 and 1983, the Bureau of Mines concentrated its fugitive dust control research on haulage road dust suppression by newer chemi-cals relatively unknown in the mineral industry, innovative dust control designs for haulage trucks, chemical tailing basin stabilization, and combined chemical and vegetation tailing basin stabilization. Relatively unknown dust suppression chemicals and innovative aerodynamic modifications to haulage truck fender designs were tested on a Minnesota sand and gravel operation haulage road. Magnesium chloride salt at 95-pct control efficiency and a petroleum derivative at 70-pct control efficiency were effective in suppressing dust generated by haulage vehicles; however, none of the fender modifications were successful. Commonly used dust suppressant chemicals were tested on a Minnesota taconite tailing basin to reduce the dust lift-off during the spring and fall dry seasons. The most successful chemical was lignin sulfonate with a seasonal cost of less than $200 per acre to achieve 90-pct dust control. When chemical treatments for immediate dust control were com-bined with revegetation for permanent control, the most promising chemical treatment based on vegetation response was lime-neutralized lignin sulfonate.

Jan 1, 1987

By E. G. Davis

As a result of interest by the U.S. Department of Energy, the Bureau of Mines conducted studies on comminution of bituminous coal to the 2-um particle size range using the Bureau-developed turbomill. Both "plant grind" size (80 pct minus 75 um) and microsize (minus 10 um) coal can be produced in a single step with the Bureau's turbomill. In 15 min, minus 2.4-mm coal milled in water with steel shot was reduced tc 65 pct minus 75 m and 26 pct minus 2 m, with an energy requirement of 139 kW^h/mt coal. Plant-grind size coal milled in water, with Ottawa sand as the milling medium, was reduced to more than 45 pct minus 2 m in 15 min, at 175 kW?h/mt. Plant-grind coal milled with steel shot was reduced to 57 pct minus 2 um in 15 min, at 138 kW?h/mt. When diesel fuel was substituted for water, the milling of the coal was less effective and less energy efficient. Keeping the pulp dispersed was critical. Without an effective dispersant, the slurry became very viscous with increased milling time, resulting in higher energy requirements, low heat dissipation, and poor grinding efficiency.

Jan 1, 1987

By S. J. Anderson

To deftne the capabilities of a nonexplosive excavation concept, the Bureau of Mines conducted reduced-scale laboratory tests of a mechanical excavation tool called a rock splitter. The splitter investigated was capable of applying combinations of radial and axial loads to rock when placed in a predrilled hole. Experiments conducted with the tool in concrete, limestone, and granite proved it capable of excavating all three materials. Break geometry in these three materials was the same, which encourages the prediction of performance in all rocks. The design of the radial-axial loading splitter's feather components significantly affected the tool's performance. It appears the design of this in-hole component should be tailored for the rock to be excavated.

Jan 1, 1987

By W. L. Cornell

The Missouri lead ores are the only domestic sources of cobalt presently being mined and processed for other materials. They represent the best short-term solution for meeting up to 13 pct of the Nation's strategic and critical cobalt needs from domestic sources. Presently, the cobalt is lost as an impurity in the copper, lead, and zinc concentrates and in the mill tailings because the technology to recover it with minium impact on present production does not exist. This paper presents results of research, built upon earlier Bureau of Mines laboratory research, to enumerate the problems encountered in cobalt recovery from the copper concentrate under actual mill conditions; to present alternative solutions to these problems; and finally, to describe the best available technology for cobalt recovery within the imposed constraints. Mineralogical analyses showed the cobalt present as a distinct mineral phase, predominately siegenite, amenable to a physical separation method such as froth flotation. Flotation was chosen for recovery because of easy adaptation by the mills. Unit processes of grinding, conditioning, and flotation were studied individually and in concert, and a series of continuous tests were run based on the parameters developed to obtain engineering data for subsequent economic analysis. Overall cobalt grades of 3.00 wt pct at a recovery of 64.0 pct were achieved.

Jan 1, 1987

By Richard A. Allwes

This Bureau of Mines report presents a procedure for the design of an arch canopy for use in rehabilitating a high-roof-fall area. Only dy-namic line loading of an unbackfilled arch canopy at its crown is considered, and the procedure does not account for an asymmetrical loading condition. The evaluation of whether an arch canopy is suitable for a particular installation depends on many variables, including in-mine conditions and the engineering properties of the structure. However, a general evaluation can be based on a comparison of the arch's maximum crown deflection and a prescribed allowable crown deflection. The design procedure is based on the concept that when an arch canopy is sub-jected to impact loading at its crown and deflects from its unloaded state to maximum crown deflection, the structure absorbs strain energy, both elastic and plastic. As a result, this strain energy can be calculated from a static load-displacement diagram for the structure. The significance of this design procedure is that it gives mine personnel an analytical tool to select an arch canopy to meet the dimensional and functional requirements of a mine entry and a prescribed allowable crown deflection.

Jan 1, 1987

By Sterling J. Anderson

Through the use of nondestructive testing techniques, the Bureau of Mines is pursuing a goal of improving the efficiency of the rock excava-tion process. Toward this end, 44 laboratory tests were conducted to identify a practical method of monitoring fracture development in rock, as caused by an excavation tool. An acoustic emission CAE) transducer was used to monitor the test samples as they were loaded. The signal from this instrument was recorded in real time along with the radial and axial loads generated by the fracturing device. Through the review of these signals on a common-time base, it was possible to see the relationship between the developing fracture and the loading conditions. As a part of the posttesting investigations, samples that were pletely fractured were sawn and ground to expose the fractures. examination of these samples allowed approximations to be made incom-Visual of the total surface created. Surface area approximations were also made for the completely fractured samples. Quantitative analyses· of the AE signals were conducted for comparisons with the calculated surface areas.

Jan 1, 1987

By Alex C. Smith

This report describes laboratory studies conducted by the Bureau of Mines on the spontaneous combustion of U.S. coals. Approximately 11 pet of U.S. underground coal mine fires are attributed to spontaneous combustion. The relative self-heating tendencies of 24 coal samples were evaluated in an adiabatic heating oven. Minimum self-heating temperatures (SHT's) in the oven ranged from 350 C for a lignite and high-volatile C bituminous (hvCb) coal, to 1350 C for two low-volatile bituminous (lvb) coals. An empirical expression was determined predicting a bituminous coal's minimum SHT in the adiabatic oven based on the coal's dry ash-free oxygen content. Several factors that can affect the self-heating process were also evaluated. The self-~eating tendency of a coal increased when the coal was dried and exposed to humidified air, and was dependent on the particle size and oxygen concentration of the air. A new moderate-scale apparatus is described, in which the self-heating tendencies of larger coal samples, 3 kg, can be evaluated. The minimum SHT's of two coals were determined and the results were in good agreement with those found in the adiabatic oven. Finally, results of a test in the moderate-scale apparatus indicated a strong dependence of the self-heating rate of a low rank coal on the moisture content of the air.

Jan 1, 1987

By John W. Kopp

Stemming is used in blasting operations to help contain explosive gases as long as possible. Stemming can reduce airblast, improve fragmentation, and reduce the chances of hot explosive gases igniting methane and dust explosions in underground mines. Stemming is required in underground coal mines but is generally not used in underground metal and nonmetal mines. Some underground metal and nonmetal mines are classified as gassy and can require special blasting procedures such as the use of stemming to minsure the safety of miners. The types and amounts of stemming material that are desirable in underground metal and nonmetal mine blasting to ensure good or improved fragmentation while containing the hot gases are largely unknown. This Bureau of Mines research examined the effectiveness of differing lengths of stemming by measuring stemming ejection times as related to burden movement. With properly stemmed blasts, stemming is contained until some burden movement has occurred. Test blasts at two surface limestone quarries were evaluated using high-speed photography. For the conditions of these tests, a stemming length of at least 26 charge diameters was found to prevent premature stemming ejection. In tests with stemming lengths of 16 charge diameters, the stemming was effective but there was early venting of hot gases through fractures in the rock. Further testing with other rock types, hole diameters, explosive types, and stemming materials as they affect incendivity is recommended.

Jan 1, 1987

By Thomas M. Barczak

Longwall roof behavior is characterized by strata displacements in both the face-to-waste (horizontal) and roof-to-f1oor (vertical) direc-tions. The roof support structure provides resistance to this motion by translation of these displacements into vertical and horizontal support loading. Observations indicate that the shield reacts with both a vertical and horizontal force to uniaxial convergence (displacement). However, there are different magnitudes depending on whether the displacement is vertical or horizontal. This makes it possible to use supports as monitors of strata activity and loading. The Bureau of Mines examined this behavior using a linear elastic model of the support structure with two degrees of freedom. Vertical and horizontal load reactions were related to associated displacement actions of the strata. This was done by determining the stiffness of the shield under controlled vertical and horizontal displacement motions in the Bureau's mine roof simulator. This report provides example predictions of strata convergence and isolation of horizontal support loading due to vertical roof convergence using the linear elastic shield model. The report also examines efforts to determine strata behavior by direct measurement of support displacement.

Jan 1, 1987

By T. H. Jeffers

Significant amounts of cobalt are present in readily accessible spent copper leach solutions. The Bureau of Mines investigated the feasibility of extracting cobalt from these solutions in a multiple-compartment ion-exchange (MCIX) column. The effects of aqueous flow rate, resin flow rate, column height, and compartment height on cobalt extraction were determined. Cobalt extractions of 92 pct or higher were achieved at solution flow rates of up to 5.5 gpm/ft of column cross-sectional area and an aqueous-to-resin flow ratio of 40:1. Overall cobalt extraction increased as the column height increased, but cobalt extraction per unit of length was more efficient in 8-and 12-ftco1umns than in an 18-ft column. Solvent extraction procedures were utilized to purify and concentrate the MCIX column eluates and produce a cobalt sulfate solution containing 70 to 80 giL Co. Metallic cathodes containing over 99 pct Co were e1ectrowon from this solution. Zinc, nickel, and copper byproducts were also recovered during processing of the ion-exchange eluates. Estimated total capital cost for a commercial-scale 10,000 gpm of a spent leach solution containing 26 million. With credits for zinc, nickel, and copper estimated net operating cost was $9.36/lb Co.

Jan 1, 1987

By F. J. Perzak

The Bureau of Mines conducted a flammability study of plastic ventilation ducts. Six rigid 16-in-diam fiberglass-reinforced plastic ducts from five manufacturers were examined using laboratory-scale, large-scale, and full-scale fire tests. The laboratory-scale tests included the American Society for Testing and Materials E162 radiant panel test, the E2863 oxygen index test, and the standardized small-scale flammability test (S3FT) developed by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and replicated by the Bureau of Mines. Ten-foot lengths of the same ducts were also subjected to a large-scale vertical fire test, and 20-to 30-ft lengths were tested in a full-scale in-mine fire test at the Bureau's Lake Lynn Laboratory mine. The data from the laboratory-scale radiant panel test and oxygen index test indicated that the ducts were fire-resistant, However, five of the six ducts failed the S3FT and vertical fire tests, and four of the ducts failed the full-scale in-mine tests with flame propagation rates that ranged from 3 to 10 ft/min. The results indicate the need for improved fire-resistant plastic ducts. The good agreement between the S3FT re-sults and the vertical and full-scale tests show that the S3FT provides a good indication of the flammability of fiberglass-reinforced plastic ducting under realistic fire conditions.

Jan 1, 1987

By Stephen A. Swan

This Bureau of Mines report discusses research to analyze and evaluate extended bumper systems in order to determine the degree of protection provided to equipment operators in the event of rear-end collisions be-tween off-road rear-dump haulage trucks. The basic characteristics of rear-end collisions were determined, and a detailed analysis of the col-lision dynamics was performed to identify the magnitude and direction of impact loads, the amount of energy that must be absorbed during impact, and the major factors that affect the outcome of a collision. Separate bumper designs were developed to facilitate attachment to four 170-st-capacity haulage truck frame types.

Jan 1, 1987