Search Documents

By Wallace W. Roepke

The Bureau of Mines determined coal-cutting forces and primary dust generation of four styles of radial gage bits as used on end rings of continuous mining machines. Direct comparisons for reference were made with two widely used conical plumb-bob types having 60' and 90' (nominal) included tip angles. The cutting forces for all of the gage bits were similar to those of the 60°-tip plumb-bob bit. All bits except the RAD-3 gage bit generated similar amounts of primary total dust at shallow cutting, but during deeper cutting, the amounts varied and the gage bits produced as much as 2-1/2 times the dust produced by the 60° bit. This seems atypical since past experience has always shown differences in dust generation at shallow cutting. The specific energy was more like that found previously with other bits, since the values were spread at shallow cutting but became nearly similar at deeper cuts. The 90° bit and the RAD-3 gage bit are not recommended for use except in extremely difficult cutting conditions where dust and forces are of secondary importance. The choice among the remaining four bits can be made on the basis of dust, energy, forces, or cost, as circumstances dictate.

Jan 1, 1983

By Wallace W. Roepke, Jon I. Voltz

"The Bureau of Mines determined coal-cutting forces and primary dust generation of four styles of radial gage bits as used on end rings of continuous mining machines. Direct comparisons for reference were made with two widely used conical plumb-bob types having 60° and 90° (nominal) included tip angles. The cutting forces for all of the gage bits were similar to those of the 60°-tip plumb-bob bit. All bits except the RAD-3 gage bit generated similar amounts of primary total dust at shallow cutting, but during deeper cutting, the amounts varied and the gage bits produced as much as 2-1/2 times the dust produced by the 60° bit. This seems atypical since past experience has always shown differences in dust generation at shallow cutting. The specific energy was more like that found previously with other bits, since the values were spread at shallow cutting but became nearly similar at deeper cuts. The 90° bit and the RAD-3 gage bit are not recommended for use except in extremely difficult cutting conditions where dust and forces are of secondary importance. The choice among the remaining four bits can be made on the basis of dust, energy, forces, or cost, as circumstances dictate. INTRODUCTIONThe Federal Coal Mine Health and Safety Act of 1969, with revisions in 1977, was enacted to ensure more healthful and safer working conditions for miners. The Bureau of Mines coal-cutting research facility at Twin Cities (MN) is examining fundamental aspects of the cutting system, including generation of primary dust causing pneumoconiosis in miners and ignition of methane by the frictional impact of cutting bits used on continuous mining machines (CMM's). The cutting system is defined as the cutter-mineral interface area with all its variables, e.g., forces, speed, cutter geometry, bit-mounting geometry, and wear. It has become obvious over the past several years that the cutting system directly affects the economics and design of the ""total system,"" which is defined as all areas of the operation, from the mine face to the preparation plant, which support the mineral recovery by cutting tools to obtain a salable product."

Jan 1, 1983

By Wallace W. Roepke

Four bit designs, two conical and two radial, were tested in coal against a 60° conical reference bit to obtain data on orthogonal cutting forces and primary respirable dust generation. One conical and one radial design were modified by the Bureau of Mines for these tests. Results were mixed: One radial bit used substantially lower overall cutting forces and specific energy than the other bits and was the only cutter lower on energy and most forces than the standard 60° bit. How-ever, it generated more specific and total dust than any other bit. The four bits were also tested for incendivity, with a 90° plumb-bob bit as the reference. The frictional ignition tests were designed to simulate both trimming top rock and cutting such rock during advance on-sump. Results of these tests were also mixed. The radial bits were substantially less incendive than the reference bit and caused no ignitions in either top trimming or sump modes. Only the modified mushroom-tipped conical bit caused ignitions. Bits similar to this modified design should not be used on drum-type miners in gassy mine areas; in-stead, the other types of bits tested should be used to reduce ignition potential to a minimum.

Jan 1, 1983

By Wallace W. Roepke

The Bureau of Mines tested new designs of drag bit cutters with sintered diamond inserts instead of standard tungsten carbide tips. The bits were tested for orthogonal cutting forces, primary dust generation, and incendivity, with a standard plumb-bob type conical cutter (600 included tip angle) as the reference. Preliminary wear and impact-failure testing were also done. The results were mixed. Two new designs had forces similar to those of the reference bit, but one new design had about twice the normal force. This same design had almost twice the specific energy during shallow cutting but generated an equal or slightly lower amount of primary dust than did the reference bit. Incendivity was eliminated for two radial designs. One conical design had ignition only after more than 15 impacts, but the other conical design was incendive. Impact failure occurred, but not so quickly as anticipated. Over 7,500 impacts on a sandstone face, with a total cutting distance of more than 1,981.2 m, only scuffed the leading edge of the sintered diamond cutting face but put hairline cracks in the substrate mounting pad. Additional design and testing are needed to develop an optimum cutter, but prospects look good for this material.

Jan 1, 1983

By Gwendolyn D. Hood

The Bureau of Mines investigated techniques for dewatering slurries from talc-processing operations to improve water reclamation and pro-duce dewatered solids suitable for disposal. Various flocculating reagents were evaluated, and a nonionic polyacrylamide was found to be most effective in a specialized flocculation dewatering technique. The flocculation dewatering method was applied in laboratory batch tests and in continuous tests using a static screen, a belt-roller device, and a clarifier-thickener laboratory unit. In continuous tests using the unit, wastes of 3.5 pct solids were dewatered to 56.9 pct solids using 0.03 Ib of flocculant per ton of dry solids treated.

Jan 1, 1983

By T. W. Smelser

This Bureau of Mines report presents a review of underground testing, test results, and design guidelines of steel-fiber-reinforced concrete (SFC) mine support (cribbing) developed at the Spokane Research Center. The objective of the work was to verify, in field applications, the performance, economics, and acceptance by the mining industry of the SFC supports and establish design guidelines for their use underground. Results indicate superior performance, favorable economics, and enthusiastic acceptance by the mining industry.

Jan 1, 1983

By Roy T. Sorensen

The Bureau of Mines has investigated the recovery of cell-grade alu-mina by RCI leaching of calcined kaolin in the alumina miniplant at its Boulder City (NV) Engineering Laboratory. Classification and thickening were used for separating aluminum chloride leach liquor from the siliceous residue generated in the acid leaching step of the clay-HCI process. Coarse solids were classified from fines at 115 mesh and countercurrently washed in three additional spiral classifiers. Fines were treated in a conventional five-thickener, countercurrent decantation circuit. When this method was applied to the solids-liquid separation of slurry from RCI leaching of minus lO-mesh calcined kaolin, 75 pct of the residue reported as classifier sands and 25 pct as thickener underflow. Predicted individual classifier and thickener area requirements were 6 and 25 ft2/tpd, respectively. Total thickener circuit flocculant requirement was 2.4 lb/ton solids. Aluminum chloride pregnant liquor was produced that analyzed 8.4 pct A1203 and contained more than 97 pct of the alumina in the liquid phase of the slurry. Bench-scale settling tests were used to correlate fines content of leach residue to thickener area and flocculant requirements.

Jan 1, 1983

By J. A. Eisele

The Bureau of Mines is investigating the recovery of alumina from domestic nonbauxitic resources, including anorthosite. The United States has large reserves of anorthosite, but its aluminum content is less than 50 pct soluble in acid, unless a source of fluoride is added to the acid. A flowsheet that includes leaching with HCl and fluoride followed by crystallization of AlC13.6H20 from the pregnant liquor by HCl gas injection was designed. Approximately 90 pct of the aluminum values were recovered from the anorthosite when a ratio of 0.14 mole of fluorine per mole of aluminum was used. Sodium chloride is cocrystallized with the A1C13.6H20 but is removed by water washing of the Al203 product. A material balance is given based on results of laboratory studies of the unit operations.

Jan 1, 1983

By James P. Bennett

To identify construction materials for emerging technology in chemical and metallurgical processes, the Bureau of Mines investigated the acid resistance of ceramic materials. Eight commercial ceramic materials comprising two red shale, two fire clay, a silica, a five-claybonded silicon carbide, a carbon, and a high-alumina brick were evaluated. Samples were exposed for 110 days to 20 wt pct HCl at 50°, 70°, and 90° C and to 30 wt pct HCl at 70° C. Statistically significant changes in cold crushing strength, volume, and weight were generally small or not detected. The leach rates of Al, Ca, Fe, K, Mg, Na, Si, and Ti ions were monitored. The carbon brick sample had the best acid resistant properties with a maximum total leached ion weight loss of 0.004 wt pct. The silicon carbide, the silica, and one of the fire clay bricks also had excellent acid-resistant properties.

Jan 1, 1983

By Jon C. Volkwein

The Bureau of Mines conducted a series of tests to evaluate the effectiveness of mixing a compressed-air-generated foam with dried whole-grain silica sand to suppress dust in minerals processing plants. Dust at downstream transfer points was monitored with personal gravimetric samplers and with Real-Time Aerosol Monitors (RAM's) that were connected to strip' chart recorders. Results showed dust reductions of 80 to 90 pct on three separate occasions at two different plants. The mechanism by which foam suppresses dust is discussed, as are the constraints on the use of foam, which may include incompatibility of the foam with the mineral product, difficulty in controlling the foam generator, and cost.

Jan 1, 1983

By Seth C. Schaefer

The Bureau of mines investigated thermodynamic properties of MnSO4 and 2CdO CdSO4 to obtain basic thermodynamic data applicable to the treatment of mineral concentrates during roasting and sintering processes. Standard Gibbs energies of formation were determined with high-temperature galvanic cells using stabilized Zr02 as the electrolyte. Potential measurements were obtained from the cells?

Jan 1, 1983

By J. W. Walkiewicz

The Bureau of Mines investigated alloys containing lanthanum (La), praseodymium (Pr), neodymium (Nd), cobalt (Co), copper (Cu), iron (Fe), and magnesium (4g) as possible components of a permanent magnet mate¬rial utilizing a cerium-free synthetic mischmetal (M) as a substitute for scarce samarium (Sm) metal. Magnets containing M-Co-Cu-Mg and M-Co-Cu-Fe-Mg were fabricated by powder metallurgy techniques and evaluated. A synthetic mischmetal (M20) containing 20 pct La, 60 Pr, and 20 Nd yielded the best overall magnetic properties. The M20-Co-Cu-Mg alloys had energy products as high as 13.2 MGOe, remanences as high as 7.89 kG, normal coercivities as high as 6.26 kOe, and intrinsic coercivities as high as 13.4 kOe. The best value of intrinsic coercivity, 22.9 kOe, was obtained with an M-Co-Cu-Mg magnet in which the synthetic misch¬metal contained 30 pct La, 50 Pr, and 20 Nd. These values compare favorably with those of the Sm-Co magnets fabricated and measured at the Bureau's Reno Research Center, which had energy product of 15.1 MGOe, remanence of 7.8 kG, normal coercivity of 7.5 kOe, and intrinsic coercivity of 27.4 kOe. Iron substitution for part of the cobalt resulted in a decrease of magnetic properties, although several percent iron can be added before a drastic loss of magnetic properties occurs.

Jan 1, 1983

By W. C. McLaughlin

Under a cooperative agreement, the Bureau of Mines, Magma Copper Co., and ASARCO, Inc., tested backfilled ground support systems at t.wo elevations in Magma's San Manuel, AZ, mine. The tests were mainly for guidance in designing the loading crosscuts of the new ASARCO Sacaton underground mine. Two-piece, wide-flange steel sets for 8-by 8-ft (2.44-by 2.44-m) and 11-by II-ft (3.36-by 3.36-m) openings were designed. Set spacing was 3 ft (0.91 m) and 5 ft (1.52 m), respectively. After erection, the sets were lagged with various test materials. The void between the lining and the ground was backfilled with sand and pea gravel. Instruments measuring strain (used to determine changes in stress) were placed beneath the sets and in the backfill. Results indicate the backfilled sets in the smaller drift (2315 grizzly level, panels 6 and 7) of 8-by 8-ft (2.44-by 2.44-m) cross section are a viable permanent support system, lower in cost than the standard formed concrete. Results are inconclusive in 2615 grizzly level, panels 5 and 6, where wide-flange steel sets were used with 5-ft (1.52-m) long concrete gob lagging of T-design.

Jan 1, 1983

By B. W. Madsen

A modified transpiration apparatus was devised by the Bureau of Mines to permit rapid and accurate measure of the vapor transport and vapor diffusion coefficients of antimony sulfide (Sb2S3) and other compounds at temperatures to 1,045 K. The apparatus was equipped with dual condensers and valves to switch the flow of vapor in a fraction of a second from one condenser to the other, thus allowing short-interval sampling under equilibrium conditions. Reliability of the technique was established by measuring the vapor pressure of ZnC12 as a function of temperature and comparing the results with published data. As part of an investigation of the vapor concentrations and species of accessory element sulfides associated with copper and zinc smelting, the apparatus was used to measure the rate of vapor transport and diffusion coefficients of vapor over liquid Sb2S3 as a function of temperature between 870 and 1,045 K. The calculated vapor density was combined with published direct measurements of vapor pressure to calculate the average molecular weight of the gaseous species. Average molecular weight of the vapor in equilibrium with Sb2S3 ranged from 286 to 112 g/mol over the temperature range studied.

Jan 1, 1983

By Rolland L. Blake

The Bureau of Mines investigated the mineralogy, tonnage, and beneficiating characteristics of oxidized (nonmagnetic) taconite iron resources of the Western Mesabi Range as part of its program to insure adequate future domestic mineral supplies. Magnetic taconite currently provides about 95 pct of Mesabi production, but the large tonnages of oxidized taconite between the magnetic deposits will be needed to help meet future domestic demand for iron ore. Three bulk samples that represent large tonnages from the Western Mesabi Range were selected to determine their mineral composition and liberation by light optical microscopy and to test their beneficiating response. This report describes the mineralogy and liberation characteristics of the three samples of the Biwabik Iron-Formation for 26.5 mi (42.7 kID) from Keewatin to Grand Rapids, MN. (Details of response to beneficia-tion were reported previously.) The samples represent mostly material from the Lower Cherty Member of the Biwabik-Iron Formation, although one sample included some Upper Cherty Member. Minerals of all three samples were quartz (chert), hematite, goethite, and minor to trace amounts of magnetite, iron carbonate, and iron silicates. It was concluded that the oxidized taconites of the Western Mesabi Range represent a subeconomic indicated resource that can be selectively mined and beneficiated as a future large source of iron feed for steelmaking.

Jan 1, 1983

By S. J. Gerdemann

In support of its objective to improve mine safety, the Bureau of Mines has searched for better materials and systems to anchor roof bolts. TIlis report describes a study on the effects of mine waters upon accelerated gypsum, one of the materials under consideration. The accelerated gypsuw dissolved at an appreciable rate relative to an assumed 10-yr life span of a roof bolt. Surface orientation, initial ion concentration of a dissolving solution, and flow rate of the solu-tion had substantial effects on the dissolution rate. Factors such as water-cement ratio, accelerator content, wax capsule additions to the gypsum in cartridge-installed bolts, surface area, temperature, and curing duration had little effect. In an actual roof-bolt environment, dissolution will occur in static solutions to the solubility limit of gypsum (~2 giL) and cease, result-ing in minimal damage; but in flows of unsaturated solution as slow as 1 L per month, a loss of up to 10 pct will occur in 2 yr. Since miners cannot readily measure the flow or ion concentration of static-appearing water at every roof-bolt site, all such water must be assumed to be pure and flowing. It is recommended that gypsum-bonded roof bolts be confined to dry roofs only.

Jan 1, 1983

By H. William Zeller

The Bureau of Mines is conducting research to determine whether the use of chemical surfactants improves respirable coal dust control and is evaluating laboratory test criteria for selecting effective surfactants. This publication presents the results from wetting effectiveness tests with emphasis on the capillary rise test. The test variables investigated included coal particle size, type of surfactant, surfactant concentration, test duration, and mineral con-tent of the water. In addition to the rise test, measurements of con-tact angle, zeta potential, and sink time for various coal and surfactant combinations were conducted. No significant correlations among the four wetting tests were observed, a surprising result which implies that each test type measures specific aspects of the wetting phenomenon and also that each test type should only be used to select surfactants for specific applications. For example, the rise test shows solution penetration into porous materials, and the sink test discriminates among surfactants for dispersing finely ground materials into suspension. Another important conclusion is that combinations of agents retain their individual wetting properties, allowing mixtures to be for-mulated to perform well in both rise and sink tests.

Jan 1, 1983

By D. E. Shanks

The Bureau of Mines surveyed a variety of inorganic ion-exchange materials to determine their suitability for removing valuable accessory elements and troublesome contaminants from metallurgical process and waste streams. Most of the materials, which included molecular sieves, heteropolyacid salts, and hydrous metal oxides, did not give adequate separations, did not have the necessary stability in strong acids or bases, or were not in a physical form suitable for ion-exchange use. Many of the suitable inorganic materials, especially the hydrous oxides, were capable of cation exchange with high capacity only in basic conditions, which caused hydrolysis of most of the cations tested. Multivalent anions, such as arsenate and phosphate, were easily removed from acidic solutions by hydrous oxides. Hydrous zirconia was the best material for this purpose. Multivalent anions were not easily des orbed because of compound formation; therefore, conventional ion-exchange techniques could not be employed. As an alternative approach, hydrous ferric hydroxide was used as a filter material to remove arsenate and phosphate from acid solutions. One gram of arsenic was removed from solution for each 20 g of ferric hydroxide. Ferric hydroxide is preferable to hydrous zirconia for use as a filter material because of low cost.

Jan 1, 1983

By R. R. Lowery

An analysis of three 1-1/4-diam manufactured wire ropes of 6x19 classification was done to identify and describe reference conditions of new rope. Reference condition is of value when examining tested or retired ropes. Measurements of strand and rope pitch and of wire and rope diameter confirmed adherence of all ropes to those construction specifications. Mechanical properties of strength and ductility were determined by accepted methods for the ropes and wires from the ropes. Individual wires from one rope failed to meet minimum wire ductility values. Wire chemical composition varied in average carbon levels, from 0.70 to 0.78 wt pct, and in manganese content, from 0.45 to 0.80 wt pct. One manufacturer's product contained 1 to 3 wt pct Ni and Cr. Heavily wrought pearlitic steel microstructures were porous and contained inclusions. Cold work variations were evidenced by wrought grain width. Recorded anomalies reflected the condition of the manu-factured products. The report provides data that compare the three wire ropes studied, but cannot verify the effects that these conditions or anomalies have on rope service life.

Jan 1, 1983

By August J. Kwitowski

This report presents the results of a joint Bureau of Mines-U.S. Department of Energy project that evaluated a newly developed low-coal mining system: the 4M miniminer system. The evaluation took place from April through October 1981 and determined potential health, safety, and productivity factors for the mining system using the surface test facilities at Bruceton, PA. The planning, testing, results of testing, and a summary evaluation of the 4M miniminer system are included in the report. The miniminer system was found to be a very good concept with future potential for safe, healthful, and economic production in thin-seam mining. The mining system was also judged to have considerable potential for use in some coal seams that are presently considered unminable by other existing mining equipment. The preproduction, prototype version of the miniminer system that was tested suffered from several safety and production problems. These problems are also described, along with suggested remedies.

Jan 1, 1989