Search Documents

By Martin Hertzberg

The concept of limit burning velocities is being used to formulate a quantitative theory of flammability limits. Competing and complicating processes dissipate power from a combustion wave and quench propagation at some characteristically low limit velocity. Two earlier reports dealt with process (a), natural convection (RI 8127); and with process (b), conductive-convective wall losses (RI 8469). This report considers process (c), radiative losses, and process (d), selective diffusional demixing. The limit burning velocity for radiative losses is [(SU)c ~ e cp] It is normally not a significant process for premixed gas flames; however, for laminar flame propagation in a gravity-free environment, it is the only loss process present. Accordingly, limit velocities at zero gravity should be much lower than on earth, and premixed gases should be flammable over wider composition ranges. For highly emissive dusts, soot, or ash-forming flames, radiative losses are significant even under normal gravity conditions. Selective diffusional demixing is a complication that manifests itself in the form of cellular flame structures and wide gaps in composition between upward and downward propagation limits. It induces a burning velocity shift (?Su)d, causing the flame to behave as though it were richer or leaner than its initial composition, depending on whether the fuel or the oxidizer mole¬cule has the higher diffusivity. A simple pertubation analysis shows that the process generates stable cellular flames whenever [dsu] > 0, where ci is the concentration of the reactant with the higher diffusivity. The same analysis indicates that at the opposite stoichiometry, where [dcu] < 0, laminar structures are stabilized. A simple formula for the diameter of cellular flames is derived, which predicts that dcell should vary inversely with the product of the diffusivity difference Di -DJ, and the burning velocity slope [dc ]. Those predictions are in good agreement with the available data. Buoyancy forces for upward propagation induce flame front curvature, and hence buoyancy and selective diffusion are mutually supportive in upward propagation. Thus large gaps in composition between upward and downward limits are present in those composition domains where cellular flames are stable.

Jan 1, 1981

By Dennis R. Dolinar

Physical property tests were conducted on drill core from three exploratory holes on the Naval Oil Shale Reserve near Anvil Points, Colo. Data and regression analysis curves are presented. Data obtained above the Mahogany zone were used to estimate the potential zone of surface effects from under-ground mining. Single specimen testing was primarily used to obtain Mohr&apos;s envelope and subsequent rock properties. The technique is shown to provide satisfactory results for this rock type with a significant reduction of core preparation and testing time.

Jan 1, 1981

By William D. Riley

In order to evaluate the corrosion resistance of zirconium in mineral extraction processes, such as a clay-hydrochloric acid leaching process for extracting alumina, the Bureau of Mines conducted corrosion studies in HCl-AlC13-FeC13 environments. A series of weight loss and electrochemical tests were conducted at 25° and 65° C in aluminum chloride (AlC13) plus hydrochloric acid (HCl) solutions containing 0 to 1,000 ppm ferric ion. It was determined that zirconium, which normally exists in a passive state in chloride-containing solutions, undergoes pitting attack in solutions containing more than 100 ppm of ferric ion. It is also shown that an oxide film prepared in air at high temperature offers protection in acid solutions containing levels of ferric ion from 300 to 1,000 ppm.

Jan 1, 1981

By G. R. Palmer

Preliminary studies by the Bureau of Mines were conducted to determine the feasibility of a multiple-compartment, ion-exchange (MCIX) column simulator for examining the effect of multiple-orifice plates in the column. A rectangular, five-orifice, three-compartment, MCIX simulator with a cross-sectional plate area of 0.66 ft2 was used for the investigation. Orifices with open areas of 1, 3, and 5 percent were used with various operating conditions. The study was separated into three separate sections: (1) solution flow effect, (2) fluidization effect, and (3) resin transfer effect. The solution flow and fluidization studies showed that for solution flow rates of about 3 gpm/ft2, a I-percent open area plate functioned best, while at solution flow rates of 9 and 15 gpm/ft2, the best open areas were 3 and 5 percent, respectively.

Jan 1, 1981

By Noel N. Moebs

Studies by the Bureau of Mines have identified geologic structures in mine roof rock that contribute to many roof falls in Appalachian coal mines. These structures, including paleochannels, scours, pinchouts, slickensides, clay veins, crevasse splays, and joints, can often be identified during, and sometimes before, mine development. Mine projections can be revised to reduce the adverse effects of discontinuitites in roof structure; large roof areas of laminated sandstone or incompetent strata generally can be delineated or inferred from exploratory drill hole data, and the need for supplementary support can be anticipated. Accurate descriptions of roof geology also provide some indication of optimum length and type of roof bolts that should be installed.

Jan 1, 1981

By K. O. Bennington

The thermodynamic properties of synthetic acmite, NaFe3+Si206, were determined by the Bureau of Mines. The enthalpy of formation was determined by hydrofluoric acid solution calorimetry. The values of the standard enthalpy of formation at 298.15 K, ?Hf°298.15, from the elements and from the oxides, ?H°298.15, are ?Hf°298.15 = -615.87 ±0.71 kcal/mole, ?H°298.15 (from oxides) = -32.08 ±0.53 kcal/mole. Various experimental data were combined with other data from the literature to calculate all the related thermodynamic properties in the range of 298 to 1,263 K. The standard Gibbs energy of formation is ?Gf°298.15 = -575.8 kcal/mole.

Jan 1, 1981

By J. M. Kuchta

The Bureau of Mines investigated four simulated coal gob fires to obtain a more reliable data base for defining the state of a sealed mine fire and to evaluate the performance of various fire detectors. The fires were conducted in a multiple-entry section of the Bruceton Experimental Mine by heating 4,000 to 21,000 pounds of rubblized bituminous coal to ignition and monitoring the temperature, gas emissions, and smoke under ventilated and sealed combustion conditions. Product gas concentrations depended upon the coal bed size, coal temperature, heating rate, and oxygen concentration or ventilating condition but varied little after the fires were sealed. Expressions are given that define the temporal variation of CO and O2 after sealing when the coal temperature decreased rapidly. The CO/C02 ratio is a more sensitive fire indicator than the CO/?02 ratio, although the latter is universally used for detecting the incipient state of a coal fire. In comparison, the Jones-Trlckett ratio [ CO2 + ¾ CO ? ¼ H2 ?O2] is less reliable for this purpose. The best detector for determining the state of a mine fire after it has been sealed was a prototype submicrometer smoke particulate sensor. Limitations of the various detector systems are also discussed.

Jan 1, 1982

By Rolland L. Blake

Petrographic methods of examination were used by the Bureau of Mines on a suite of samples of ultramafic rock from Soapstone Ridge, Ga., located about 8 miles south-southeast of Atlanta. The samples were analyzed to determine (1) their potential for releasing regulatory particles upon crushing and grinding and (2) their concentration of fibrous particles that approach the dimensions of amphibole and serpentine asbestos minerals. Such particles might be generated during grading and excavation for housing and industrial development and could become a health concern. Light optical microscopy, scanning electron microscopy, and X-ray diffraction were the techniques used to examine the samples. Six of the twelve samples contained amphibole as a major mineral; in five, it was a moderate to minor mineral. One sample contained no amphiboles, and serpentine was not observed or identified by X-ray diffraction in any of the samples. In nine of the samples, the amphiboles exhibited a habit that was either prismatic or acicular, but not asbestiform. Two of the samples did contain asbestos, occurring as small veins or fracture fillings, which represented only a minor percentage of the total sample. Similar petrographic screening is recommended for examining any rock deposit or mine location to delineate hazardous and nonhazardous mineral areas.

Jan 1, 1982

This Bureau of Mines publication describes the plan used to instrument two longwall gateroads at the Powhatan No. 4 Mine of the Quarto Mining Co. Vibrating wire stressmeters, flat jack U-cells, multipoint extensometer stations, and convergence stations were installed in or on the coal pillars, roof bolts, and roof strata of the gateroad entries. The instruments measure pillar stresses, bolt loadings, and strata movements as the gateroad entries are developed and the longwall panel(s) is mined. The report details only the instrumentation plan of the longwall gateroads and not the evaluation of any subsequent data. This is because a complete analy-sis of the data cannot be made until extraction of the longwall panel(s) is complete.

Jan 1, 1982

By L. L. Oden

The Bureau of Mines analyzed vapor-aluminum-diffused stainless steels prior to conducting corrosion measurements in severely sulfidizing environments. These studies were conducted in response to the national need to better control the environmental and economic costs of corrosion. Specimens of a ferritic alloy and austenitic alloys types 316 and 310 were treated by a proprietary vapor-aluminum diffusion process and a dual vapor-aluminum diffusion process. Weights and dimensions were recorded before and after treatment, and comprehensive metallographic, X-ray, and electron micro-probe analyses were conducted for both single-and dual-vapor-aluminum-diffused specimens. Surface aluminum concentrations ranged from 26 to 34 wt-pct for all alloys. Dual treatment increased the quantity of aluminum per unit area by a factor of 2 and increased the depth of penetration by a factor of 3. The aluminum-diffused region of the ferritic alloy was single-phase aFe solid solution that was ordered on the surface, whereas two distinct diffusion layers were ob-served on the austenitic alloys. The outer layer comprised aFe solid solution that was ordered on the surface, and the inner layer was a two-phase mixture of aFe solid solution and the interrnetallic compound AINi.

Jan 1, 1982

By C. D. Litton

The results of full-scale fire tests are used to determine optimum distributions of fire sensors for the protection of conveyor belt haulageways in underground coal mines. Empirical relationships are derived that relate the spacing of fire sensors to the rate of development of the fire hazard. For this application, a critical fire size is defined as that size of fire for which belt ignition and subsequent flame spread down the belt is assured. Detection and alarm, regardless of sensor type or sensing methodology, must be achieved at some point in time before the critical fire size is reached. Based upon this approach, it is found that the horizontal spacing for products-of-combustion sensors is in the range of 300 to 600 meters, while the required thermal sensor spacing is found to be ~4 meters or less. Additional design criteria are discussed for product-of-combustion fire sensing systems.

Jan 1, 1982

By Jalna R. Zatko

Coal-clay waste slurries were dewatered in laboratory-and small-scale continuous tests by the Bureau of Mines using polyethylene oxide (PEO) as a flocculant. Dewatering from a nominal 7-wt-pct solids to over 50-wt-pct solids was accomplished using 0.5 lb of PEO per ton of feed in small-scale continuous tests. Parameters such as pH, initial solids content, and PEO concentrations were investigated. Water recovered from dewatering was reused as dilutant for PEO solutions.

Jan 1, 1982

By R. H. Lien

The Bureau of Mines developed a flue gas desulfurization process as part of its goal of minimizing the undesirable environmental impacts associated with energy and mineral-processing plants. The modified citrate process involves absorption of sulfur dioxide (S02) in a buffered citric acid solution. The S02-loaded solution is regenerated by countercurrent contact with steam in a packed tower. The wet S02 product is then dried and can be liquefied or further processed to make sulfuric acid. Test data from process investigation unit studies are presented. Material balances, flowsheets, and cost estimates are given for recovering S02 from copper smelter reverberatory gas, lead smelter sintering machine tail gas, and power-plant stack gas. Operating cost estimates show the process will add $0.04 per pound of copper, $0.01 per pound of lead, and $0.015 per kwhr to the cost of the respective operations. These costs could be substantially reduced if a source of waste heat was avail-able to provide the process steam requirements.

Jan 1, 1982

By Alexander May

In its role to provide technology to prevent or limit adverse environmental impacts associated with mining or minerals processing, the Bureau of Mines has conducted research at its Tuscaloosa Research Center to asess the environmental impacts of phosphogypsum produced by the Florida phosphate industry. Over the years, stockpiles containing 335 million tons of phosphogypsun have accumulated and the industry continues to generate an additional 33 million tons a year. Samples from approximately 1,000 feet of drill core, obtained from nine stockpiles were characterized using chemical, X-ray diffraction, emission spectrographic, radiological, and physical means. The data developed indicated that phosphogypsum is not a corrosive or toxic hazardous waste as defined by Environmental Protection Agency criteria. Radium concentration averaged 21 picocuries per gram and its content was inversely related to particle sizes. Thirty-nine elements were detected in phosphogypsum; concentrations of these elements did not vary with depth within the stockpiles.

Jan 1, 1982

By David C. Oyler

Three long horizontal holes were drilled from a directionally drilled surface hole at the Emerald Mine near Waynesburg, Pa. The purpose was to adapt the technique of directional drilling for use in draining methane from coalbeds. A 504-m (1,652-ft) long, 76-mm (3-in) diameter, circular arc pilot hole was drilled, using a downhole mud motor, to enter the Pittsburgh coalbed at a vertical depth of 305 m (1,000 ft). The hole was reamed to 222 mm (8-3/4 in) and was cased to a measured depth of 486 m (1,595 ft). Three 76-mm (3-in) diameter horizontal drainage holes were then drilled, totaling 2,909 m (9,544 ft) of horizontal hole. Improvements in drilling methods increased the average drilling rate from 20.4 ill (67 ft) to 64.9 m (213 ft) per day. The cost of drilling the directional and horizontal holes (using a Government-owned drill rig) was $1,169,530, a figure inflated by inexperience and by delays caused by lost-circulation problems and fishing operations. An estimated total drilling cost of $960,000 (including rental of a drill rig) for an improved system, was determined by a detailed cost analysis. Initial gas and water production from November 1979 through May 1980 was low because of caving of the horizontal holes drilled in shale near the bottom of the casing.

Jan 1, 1982

By C. Melvin Lepper

Microseismic energy is generated when stresses accumulated in rock formations are released in the form of fracturing. The acoustic emissions resulting from these rock fractures and movements are detectable as velocity signals in the earth near the energy source. A Bureau of Mines microseismic system that is capable of detecting the acoustic emissions from pit slope movements is described. The digital circuitry incorporated in the system allows a microprocessor program to immediately calculate and present the location coordinates for the seismic energy source in the mine pit wall. This monitoring system is compact, portable, reliable, and relatively inexpensive and rapidly provides accurate information to the mine operators about the stability of a pit slope.

Jan 1, 1982

By Steven J. Schatzel

Gas drainage through surface bore-holes has been the conventional means of methane control for U.S. longwall gobs. However, these vertical boreholes are becoming so costly, and the surface rights so difficult to obtain, that the Bureau of Mines is developing underground gob gas drainage as an alternate means of methane control for U.S. longwalls. Holes are drilled into the roof over the panel and on retreating longwalls, towards the working face from a location inby the face. As the longwall retreats, an increasing portion of the hole intercepts the fracture system over the caved gob. A surface exhauster maintains a vacuum on a pipeline parelleling the panel and draws the methane mixture out of the mine. Auxiliary systems of gob gas drain-age during longwall mining will be essential for an increasing number of coal mines. Deep and gassy mines often find ventilation insufficient for adequate dilution of methane in bleeder entries. Although this cross-measure method of degasification has been used successfully in Europe, some of the European techniques cannot be directly applied to U.S. mines. This is the first study of its kind in this country.

Jan 1, 1982

By W. L. Falke

The Bureau of Mines has developed a system that permits the "soft" soldering of aluminum and aluminum alloys with standard tin-lead solders. The method employs application of a thin nickel-copper-alloy coating to the substrate, which enables the tin-lead solders to wet readily and spread over the areas to be joined. With conventional technology, aluminum and aluminum alloys are extremely difficult to solder because tenacious surface oxide films prevent wetting. With the Bureau-developed method, the aluminum substrate is mechanically or chemically cleaned to facilitate bonding to a minute layer of zinc that is subsequently applied with an electroless zincate solution. The nickel-copper-alloy (30 to 70 pct Ni) coating is then applied electrolytically over the zinc, using immersion cell or brush-coating techniques. Development of acetate electrolytes has permitted deposition of the proper alloy coatings. The coated areas can then be readily joined with conventional tin-lead solders and fluxes. The joints so formed are ductile, strong, and relatively corrosion resistant, and exhibit strengths equivalent to those formed on copper and brass when the same solders and fluxes are used. The method has also been employed to soft-solder magnesium alloys.

Jan 1, 1983

By Michael T. Nigbor

The Bureau of Mines assisted the Rocky Mountain Energy Co. in a pilot-scale in situ leaching experiment at Casper, Wyo., to determine if sulfuric acid can be used as a cost-effective alternative lixiviant (leachant) for uranium in situ leaching. This experiment, which lasted more than 2 years, is the first fully documented pilot-scale operation in which the leaching-restoration cycle was completed using sulfuric acid instead of the more common carbonate-bicarbonate leachant This report describes activities at the experimental site, presents extensive geochemical data from startup to site restoration, compares laboratory and field experiments, and discusses the environmental aspects of acid leaching. The data showed that sulfuric acid is apparently an effective leaching solution. Three to five grams of acid per liter of ground water resulted in a production solution grade of 80 to 100 ppm uranium. Restoration was successful, but required extended flushing. The pH was the last chemical parameterto return to baseline, requiring about 350 days. This was longer than was predicted in laboratory simulations. The data also showed that mobilization of toxic elements such as selenium, arsenic, radium, thorium, and molybdenum stayed within reasonable limits and quickly fell back to preleach concentrations during restoration.

Jan 1, 1982

By J. S. Dunning

The Bureau of Mines investigated a series of Fe-Al-Mo alloys strengthened by ZrC (zirconium carbide) precipitates as chromium-free substitutes for stainless steels. Melting and fabrication methods were devised, and the effects of minor additions of columbium (niobium) and cerium on the mechanical properties and oxidation resistance were determined. Zirconium carbides could not be con-trolled reliably to produce fine precipitate dispersions. A more reliable carbide strengthening mechanism is required if the high-temperature strengths of types 304 and 316 stainless steels are to be duplicated. Workability and oxidation resistance of the alloy series were excellent.

Jan 1, 1982