Search Documents

By Jack E. Fraley

Because of their noncombustibility, silicate and magnesium oxycements are desirable for sealing shale in underground coal mines. In this Bureau of Mines investigation, cement samples were cured and tested (nonstandard tests) for submersion to note resistance to dissolution (breaking into parts), which is an important property for a coating. Nonappreciable dissolution during 1 week of submersion was set for passing the test. Over half of the coatings passed the test.

Jan 1, 1977

By R. R. Backer

The Bureau of Mines investigated the typical physical and chemical properties of coal waste materials from the western part of the United States. The results are compared, in so far as possible, with the properties of waste materials from eastern coal operations. The authors found a disparity of mines and preparation plants among western U.S. coal operations and dissimilarities with typical operations in the East. The relatively cleaner product from the predominance of surface mining and the occurrence of thicker seams in the West reduces the amount of coal preparation required and the size of the waste piles. Because of the abundance of land available for waste disposal, many of the piles are low and extended over large areas. New concepts relating statistical shear strength data to liquifaction potential are presented. The somewhat limited data indicates that western coal sludge is coarser with higher permeabilities and shear strengths than the eastern deposits.

Jan 1, 1977

By Peter F. Steidl

As part of the Bureau of Mines methane control program, the Upper Free-port coalbed was studied in Fayette County, Pa., where this coalbed lies about 650 feet below the Pittsburgh coalbed and contains the largest remaining reserves of any coalbed in the county. Coal and overburden isopachs, structure and joint pattern maps, and a fence diagram were prepared using data from gas and oil exploration logs and coal outcrops. These maps will aid in deter-mining the need and/or feasibility of degasifying the Upper Freeport coalbed in the study area. Much of the coalbed in this area is under 600 to 1,400 feet of overburden. By correlation with data from the Pittsburgh coalbed, the gas content at depths of this order is estimated to be between 140 to 300 cf/ ton of coal, for a total of 190 to 400 billion cubic feet of methane in this coalbed in Fayette County.

Jan 1, 1977

By David H. Yee

Because of environmental concerns, the Bureau of Mines investigated an anhydrous chlorination process for the recovery of copper from chalcopyrite, Pelletized concentrate was reacted continuously with chlorine in a vertical shaft reactor at 550° to 750° C to extract copper-iron chlorides and elemental sulfur. The resulting molten metal chlorides drained from the reactor and collected in a receiver while sulfur distilled from the top and condensed in a separate unit. The tests were conducted in a 10-cm-diam reactor constructed of glass and in l5-cm-diam reactors constructed from various refractory materials. A high-alumina ramming mix exhibited the best resistance to molten metal chlorides and elemental sulfur in chlorine atmospheres. A reactor made with this high-alumina refractory was operated for 55 hr under actual chlorinating conditions without suffering any deterioration. Tests results show that more than 96 pct of the chalcopyrite was converted to copper-iron chlorides and elemental sulfur. Good separation of the metal chloride and sulfur products was achieved. After filtration, elemental sulfur of greater than 99 pct purity was obtained.

Jan 1, 1977

By Noel N. Moebs

The Bureau of Mines investigated severe coal mine roof support problems along a section of main entries in the Pittsburgh coalbed in southwestern Pennsylvania to identify the causative factors. The mine roof was examined in detail, and various sedimentary structures are described that contributed directly to irregular and unstable roof. Small-scale paleochannels, scours, and related slickensides were identified as the leading cause of bad roof, and isopach maps were prepared to illustrate a method whereby the presence of these structures could be inferred in advance of mining. Probably second in importance was the occurrence of relatively incompetent flaggy, poorly cemented sandstone, weakened by coal and micaceous laminea. No effect of in situ stresses on roof stability was detected.

Jan 1, 1977

By Jack E. Fraley

In this Bureau of Mines study, sealants containing mineral wool, cement, etc, were sprayed through dry-process equipment that propels dry material pneumatically to the water-adding nozzle. Advantages over slurry applications include no mixing, no extensive cleanup, and freedom from hardened cement in equipment should power be lost. Sealants with large mineral wool nodules (>l-inch) were sprayable at rates to 900 square feet per hour for 1/2-inch thickness with little dust and smooth material flow through equipment, but they were weak for mine use, Materials containing small wool nodules (1/4-inch) were stronger but tended to plug lines because the nodules were inadequately separated in the shredder. Increasing the dedusting oil also increased line plugging by holding the nodules together in larger lumps. Best results were obtained using a 3/4-inch-nodule wool with cement binder, which provided both smooth flow through the machine and adequate strength.

Jan 1, 1977

By d&apos, Dennis V. Andrea

The Bureau of Mines and El Paso Mining and Milling Co. conducted a cooperative in situ leaching research program at the Emerald Isle mine near Kingman, Ariz. The objective of this research was to develop in situ leaching methods for 200,000 tons of ore exposed in the pit bottom and also 3,000,000 tons of ore under 200 feet of overburden adjacent to the pit. The research included core drilling for fragmentation analysis, inplace permeability testing, seismic surveys, blasting tests, blast vibration measurements, inplace leaching, and ground water monitoring. A l5,000-ton test area in the pit bottom was blasted and leached inplace for 117 days. This successful test was followed by leaching 100,000 additional tons of unblasted pit bottom ore. Two test blasts, under 205 feet of overburden and extending to 290 feet, were detonated in an area near the open pit. The second blast was detonated because the first blast did not create adequate permeability for leaching. Pit bottom leaching was discontinued and the test area under 200 feet of overburden was not leached because the company terminated operations at the Emerald Isle mine. Based on the research completed, an expanded in situ leaching system was designed, but not implemented, to recover copper from a 1,500,000-ton area at the Emerald Isle mine.

Jan 1, 1977

By Robert F. Droullard

The Bureau of Mines has investigated techniques of using gross alpha or beta detectors to continuously measure working levels. Both methods measure radioactive particulates collected on a filter paper using a constant airflow. Inherent-error studies indicate a value of about ±3 percent for the gross alpha method and about ±8 percent for the beta method in typical mine atmospheres. However, the beta method avoids problems associated with alpha detectors and is therefore more useful. Applications of these continuous working-level detectors include work area monitoring of exposure levels in underground openings, such as mines and caves, and calibrating personal dosimeters exposed over extended time intervals.

Jan 1, 1977

By Byron S. Gottfried

This Bureau of Mines report presents a method for combining the distribution curves at different specific gravities of separation, for a given piece of coal-cleaning equipment and a given raw coal feed, into a single, generalized distribution curve normalized with respect to specific gravity and, therefore, independent of the specific gravity of separation. Illustrative generalized distribution curves, based upon Bureau of Mines collected data on industrial operations, are presented for five different types of coal-cleaning equipment. The well-known concept of probable error is extended to the generalized distribution curve. It is shown that the conventional probable error is directly proportional to the specific gravity of separation. A number of sample calculations, illustrating the use of the generalized distribution curve and generalized probable error, are presented in the appendix.

Jan 1, 1977

By Kenneth J. Miller

The Federal Bureau of Mines coal-pyrite flotation process has been modi¬fied to produce a concentrated final clean coal slurry underflow that could be dewatered more effectively by filtration or centrifugation. This change was accomplished by redesigning the Bureau's two-stage flotation pilot plant facility and running the second-stage flotation step with undiluted or only partially diluted first stage coal froth concentrate. Results of the pilot plant flotation tests showed that substantial sulfur reduction could be achieved by flotation with undiluted pulp but some dilution is recommended for maximum selectivity. For example, coal-pyrite flotation in slurry of 25 percent solids yielded clean coal products analyzing as low as 0.7 percent pyritic sulfur and froth reject products containing slightly over 3.0 percent pyritic sulfur. In comparison, coal-pyrite flotation with pulp diluted to about 12.5 percent solids yielded clean coal containing as low as 0.4 percent pyritic sulfur and froth reject of 5.6 to 6.7 percent pyritic sulfur. Despite the need for some dilution, it was concluded that excellent coal-¬pyrite flotation selectivity could be achieved without diluting to 6 or 7 per¬cent solids as done in the earlier work. Thus the economics of coal-pyrite flotation would be improved by easing clean coal dewatering problems and by reducing second-stage flotation cell volume requirements.

Jan 1, 1977

By Joseph Cervik

This Bureau of Mines report deals with water infusion of coalbeds, which can control methane emission at face areas during developmental mining and which may sometimes suppress dust. Studies show that water infused into the coalbed flows through the fracture system and displaces the methane in the fractures and prevents migration from the solid coal. Displaced gas migrates away from the face area that has been water infused and enters the return ventilation airways. A gradual decrease in methane emission is observed from the start of infusion until the infused zone is mined through. Depending on the permeability of the coalbed, infusion pressures ranged from 300 to 2,200 lb/in2. Face emissions in the Upper Kittanning coalbed were reduced by 89 pet; reductions of 38 to 79 pet were measured in the Pittsburgh coalbed depending on the relationship between the face cleat direction and mining direction. Respirable dust levels were reduced by about 75 pct on a longwall section in the Pocahontas No.3 coalbed and by about 50 pct on a development section in the Upper Kittanning coalbed, but no statistically reliable reduction was found in the respirable dust levels in the Pittsburgh coalbed.

Jan 1, 1977

By Charles D. Litton

A new prototype ionization-attachment fire detector was developed by the Bureau of Mines for detecting combustion-generated submicrometer particulates. It is much more sensitive than the conventional ionization smoke detector, and it has the following added features: 1. A primary charging current of unipolar air ions is generated by a gold-coated, radioactive center electrode of a cylindrical diode. 2. Submicrometer particulates are flowed axially through the unipolar cloud where they acquire charge. The charged particles impinge upon a third electrode, located downstream, resulting in a current which is directly proportional to the particulate concentration. 3. Additional electrodes analyze the particulates in terms of their mobility and thus determine their size distribution. 4. A filter and cyclone assembly protect the ionization chamber against ambient dust. An analysis of conventional ionization smoke detector performance is also presented in terms of source strength, chamber geometry, and applied potential.

Jan 1, 1977

By J. E. Matta

The Bureau of Mines made laboratory absorption measurements on oil shale samples, which showed that the amount of methane absorbed is proportional to pressure and oil yield, and can be much larger than would be predicted based solely on porosity. Oil shale cores collected in the field were also measured for their gas content using the Bureau of Mines direct method. Cores taken from deep locations and far from outcrops yielded more gas than cores from shallower locations or at outcrops, when taking into account variations in oil yield, and all data indicate that oil shale mines that are both deep and far from an out-crop will emit low levels of methane gas.

Jan 1, 1977

By B. W. Haynes

With the national focus on energy, the combustible fraction of urban refuse is being extensively considered as a fuel supplement for coal in the generation of heat and power. The objective of these analytical studies by the Bureau of Mines was to determine the concentration of major, minor, and trace elements in the combustible fractions collected at various locations in the Bureau's urban refuse recycling pilot plant located at College Park, Md. The samples processed through the plant were submitted by various municipalities that are considering resource recovery as an alternative to landfill or other means of disposal. Twenty-five elements were determined in samples from six geographic areas and were compared with element concentrations found in typical coal samples.

Jan 1, 1977

By Ann G. Kim

The Bureau of Mines estimated the methane content of a coal, which depends primarily upon rank and pressure, from the adsorption equation V =kpn, where k and n are constants related to rank. By incorporating corrections for moisture, ash, and temperature, and estimating pressure and temperature as a function of depth, the methane content of coal in place can be estimated from the following equation: [ ] Values calculated with this equation generally are in reasonable agreement with direct determinations. By assuming a standard moisture and ash content, and using the hydrostatic head to estimate pressure, a graph of rank and depth versus gas content was constructed. Although estimated values were consistently high for several high-volatile bituminous coals from an area where the pressure is known to be less than hydrostatic, the estimated methane content for most coals shows reasonable agreement with values determined by the direct method.

Jan 1, 1977

By Ann G. Kim

The Bureau of Mines estimated the methane content of a coal, which depends primarily upon rank and pressure, from the adsorption equation V kpn, where k and n are constants related to rank. By incorporating corrections for moisture, ash, and temperature, and estimating pressure and temperature as a function of depth, the methane content of coal in place can be estimated from the following equation: [ ] Values calculated with this equation generally are in reasonable agreement with direct determinations. By assuming a standard moisture and ash content, and using the hydrostatic head to estimate pressure, a graph of rank and depth versus gas content was constructed. Although estimated values were consistently high for several high-volatile bituminous coals from an area where the pressure is known to be less than hydrostatic, the estimated methane content for most coals shows reasonable agreement with values determined by the direct method.

Jan 1, 1977

By C. H. Elder

Two degasification test boreholes were drilled to depths of 1,238 and 1,212 feet on Bureau of Mines property at Bruceton, Pa., as part of the Bureau's long-range coal degasification program. The holes provided detailed geologic information and geologic sections, which were correlated with regional stratigraphic cross sections prepared by the Pennsylvania Geological Survey. Gas content determinations and coal analyses were made on the Upper Freeport, Middle Kittanning, Clarion, Brookville, and Mercer coalbeds; gas content of the coalbeds ranged from 53 to 165 cubic feet per ton. Formation pressure and gas flow tests were conducted on selected coalbed intervals in borehole 1; formation pressures ranged from 292 to 473 psig. The middle Kittanning coalbed was hydraulically stimulated using very heavy gelled water, but gas production remained low because gel residue and formation water inhibited the flow of gas. Gas contents in the Clarion, Upper Brookville, and Mercer coalbeds were anomalously low owing to the proximity of porous sand-stones which act as reservoirs for gas migrating from coalbeds.

Jan 1, 1977

By Natesa I. Jayaraman

A field study was conducted by the Bureau of Mines to determine the feasibility and effectiveness of a secondary ventilation system retrofitted onto an Eickhoff EDW 340L double-drum shearer as a technique for controlling respirable dust generated during a longwall mining operation. An airflow duct was formed by enclosing the bottom of the undercarriage with steel plate and cutting air channels through the ends of the undercarriage frame. Air intakes were provided behind each cutting drum and at several locations along the undercarriage. Grills were installed at the intakes to prevent the broken coal from entering the ducting. A dust collector consisting of 5,000-ft3/min fan, water sprays, and a minicyclone panel was installed on the shearer at the tailgate end. Field results indicated that the secondary ventilation system reduced respirable dust more than 60% along the face. Reduction was less near the intake airway and when secondary dust sources occurred.

Jan 1, 1977

By David Schlain

The Bureau of Mines investigated methods for electrodepositing platinum-group metals from molten cyanide baths. The preparation of thick, protective coatings on molybdenum, Inconel, graphite, stainless steel, copper, and other structural metals were studied, as well as the electroforming of platinum and iridium crucibles. Iridium, rhodium, and ruthenium can be electrodeposited under an inert atmosphere, while platinum and palladium require the presence of air. Electrolytes may be prepared by direct-current electrolysis in NaCN or mixtures of NaCN and KCN using anodes of the particular platinum-group metal. When the concentration of metal increases to about 0.3 or 0.4 percent, the deposits become bright, adherent, and coherent. Current densities may be 10 to 25 ma/cm2, and plating rates are often 0.5 mil/hr. Platinum and palladium baths deteriorate because of the oxidation of cyanide to cyanate and carbonate, and the precipitation of metal. Changes in the platinum cyanide bath are relatively slow. The protection against oxidation afforded by the platinum-group metal coatings is evaluated by testing encapsulated specimens in a thermogravimetric balance. Surface pretreatment and the use of undercoats are discussed.

Jan 1, 1977

By George J. Conroy

To provide data as a basis for proposed acceptance standards and procedures covering permanent splices in trailing cables, the Bureau of Mines conducted testing programs on the flexure life in flat types W and G dc trailing cable splices and ground conductors. Primary reliance was placed on laboratory testing, although some cross comparisons were made at manufacturers' plants and mine operations Besides providing data for acceptance standards and procedures, results of the program should promote the general improvement of commercially available splice kits.

Jan 1, 1977