Search Documents

By John W. Buch

Upon review of German World War II mining practices and equipment for planning coal, the Federal Bureau of Mines initiated research leading to the development of a pneumatic planer for anthracite. The results of tests are reported in this manuscript. It was demonstrated (1) that hard anthracite can be planed and (2) that the design and operating requirements are within the limits of present-day engineering and technology. For hard anthracite, the depth of cut indicated is 4 to 6 inches; with a chain pull of 20 to 40 tons and the speed of planer travel of 18 to 20 feet per minute, a 40-hp. motor will be required for the planer hoist. Compressed-air requirements for the planer will be 250 to 300 c, f, m, at 60 to 70 p. s, i. It was learned that the length of the 4 individual sections of the planer should not exceed that of the individual troughs of the armored chain conveyor (5 feet in this instance); otherwise, bottom coal will be left in synclines, and the planer will override the conveyor at anticlines. Pneumatic pushers should be operated from a separate compressed-air line fitted with a pressure regulator. Results indicate that additional development work is warranted.

Jan 1, 1957

By Milton B. Hall

This report discusses in detail laboratory and pilot-plant tests conducted from January 1951 until January 1955 at the Northwest Electrodevelopment Experiment Station of the Bureau of Mines, Albany, Oreg., on defluorination and recovery of evolved fluorine from phosphate rock. Results of use tests of defluorinated phosphate rock by cooperating agricultural colleges and the United States Department of Agriculture are also included. In 1954 the consumption of fluorspar, the only domestic fluorine-bearing mineral of commercial importance, was approximately 478,000 short tons; 245,000 tons was from domestic mines. The production of marketable phosphate rock in the same period was about 13,800,000 long tons. Of this total amount, approximately 15 percent was produced in the West. From the viewpoint of conservation and utilization of fluorine as a natural resource, it is interesting to note that the total estimated quantity of fluorine in domestically produced phosphate rock is more than double that present in domestically mined fluorspar.

Jan 1, 1958

By W. H. Oppelt

Converting small-particle lignite to a stable, storable fuel of relatively high heating value was investigated. The fuel was prepared by thermal pretreatment of the lignite in an 8-inch i. d. rotary-drum retort, then the pretreated material was pelletized in an experimental 15-inch-i. d. rotary-drum pelletizer. Pelletizing tests were made with both starch and bituminous binders. During the first phase of the project, the quantity, composition, and heating value of products from the thermal processing of Kincaid lignite from Burke County, N. Dak., in an B-inch i. d. rotary-drum retort were investigated at a series of temperatures from 250° to 950° F. to establish optimum conditions for preparing feed material for pelletizing. To determine the response to thermal treatment of different lignites, 5 other lignites from Divide, McLean, Mercer, and Stark Counties, N. Dak., and 1 lignite from Saskatchewan, Canada, were processed at 700° F.

Jan 1, 1958

By Roy F. Abernethy

All samples tested showed some loss of heating value for the 5-month period under all 4 storage conditions. The losses increased as the time of storage increased, with the pan-storage samples showing somewhat greater losses than those in cans. The individual daily analyses for the first 2 weeks and the analyses every other day for the third and fourth weeks of storage vary within the approximate tolerance of the test for heating value. During the first 2 months of storage the changes in heating values were not Significant for the samples from Pennsylvania, Indiana, and Colorado. The Ohio coal indicated some loss by the end of I month, which increased to a value measurable with certainty by the end of 2 months. These data show that (1) small changes may occur even to samples in closed cans and (2) the laboratory sample should be handled as expeditiously as is practical until the analysis is completed. The statement by the ASTM that "If the B.t.u. determination is an important consideration in the sale of coal, the time elapsed between sampling and analysis shall not exceed 30 days,"3/ is quite adequate for 3 of the 4 coals tested. The change in the Ohio coal stored for 30 days is merely indicated and could not be determined with certainty by the techniques normally employed. The data on free-swelling indexes determined on can samples, after 30° C. air drying, show that only the Indiana coal lost more than one unit in free-swelling index number in 120 days. No significant changes were observed with the samples from Pennsylvania, Ohio, and Colorado in the 5-month period.

Jan 1, 1958

By William M. Nabors

As a part of a program to promote conservation and efficient utilization of petroleum resources, Bureau of Mines engineers are studying secondary oil-recovery projects in the United States. Published reports that set forth the pertinent facts of these operations help others to profit by the experience gained. This report presents the results of a study of secondary-recovery methods used in Kentucky by the Cumberland Petroleum Co. on its L. C. Bailey lease, Oil Springs pool, Magoffin County, Ky. This is believed to be the first water-flooding project in eastern Kentucky (fig. 1).

Jan 1, 1958

By LaMar G. Evans

The rapid determination of uranium in ores by radiometric means was investigated by the Bureau of Mines. Among the various procedures and schemes tested, two showed most promise. They were the ratio scheme developed in the Bureau's Tucson, Ariz., laboratory and the equilibrium method developed by the Canadian Department of Mines and Technical Surveys. The ratio method is a simple, empirical procedure for classifying the state of equilibrium in ores by measuring their radioactivity by means of a Geiger-Muller counter under three different conditions, using filters. The principal merit of the method is in providing a clue as to the reliability of equivalent uranium determinations.

Jan 1, 1958

By T. E. Gray

This report describes the preparation characteristics of the most significant coal beds in Wise County, Va. It is one in a series of reports planned to determine coals suitable for the production of metallurgical coke, either as mined or after beneficiation. Wise County produced approximately 6,600,000 tons of coal in 1955, of which about 2,110,000 tons was cleaned mechanically. The Federal Geological Survey has estimated that 1,341 million tons of measured and indicated coal reserves remained in the county as of January 1, 1951.

Jan 1, 1958

By N. A. Eilertsen

This report describes field investigations conducted in 1953 of two occurrences of manganese and a separate magnetic anomaly in the Southern manganese district of Aroostook County, vicinity of Houlton, Maine -the Pierce deposits, in Hammond Plantation Township; the Burnham anomaly, also in Hammond Plantation; and the Nickerson-Farm prospect in Hodgdon Township. The manganese occurs in a thinly laminated sedimentary rock containing manganiferous carbonate interlayered with fine-grained metamorphosed sediment, rich in chlorite or hematite. The surrounding rocks are mostly dark gray-green slates. Samples composited for metallurgical testing from the Pierce deposits and the Nickerson-Farm prospect assayed 9.0 to 12.3 percent of manganese. More than 90 percent of the manganese could be extracted with sulfuric acid, but in most instances 30 to 40 percent of the iron was also extracted. Leaching tests indicated that, after being reduced in a hydrogen stmosphere at 600° C., about 85 percent of the manganese could be selectively extracted by a solution of ammonia-ammonium carbonate with iron extraction of only 14 percent.

Jan 1, 1958

By H. L. Riley

At the Southern Experiment Station, Tuscaloosa, Ala., reports are prepared from time to time on results of washability studies of coal from important beds in the Southern Appalachian region. The investigations that provide the material for these reports are made by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the mine operators. The principal objective of a washability study is to obtain technically and commercially important data to aid in determining the best methods for preparing and utilizing the Nation's reserves, particularly of coking coals. Such information is also important from the standpoint of conservation, because it facilitates the selection of preparation methods that will yield an acceptable product with a minimum loss of coal to the rejects.

Jan 1, 1958

By M. J. Ferrante

Laboratory-scale tests were undertaken to examine several electrolytes for possible use in separating nickel and cobalt from products being prepared at Nicaro, Cuba. The most extensive work was done with nickel sulfate-ammonium fluoride, ammonium fluoride, ammonium sulfate, and nickel sulfate-boric acid electrolytes. All four electrolytes exhibited some selectivity for dissolving nickel carbonate from Nicaro basic carbonate used for regeneration. The nickel sulfate-ammonium fluoride electrolyte exhibited less selectivity for dissolving nickel carbonate from Nicaro basic carbonate than it did from synthetic mixtures. Ammonium fluoride leaching experiments showed that a low concentration and high temperature gave a good nickel extraction with C. P. reagents; however, this was not confirmed in tests using Nicaro basic carbonate. Electrolytic tests employing ammonium fluoride leach liquors gave no further separation, since approximately 90 percent of the cobalt was deposited at the cathode with the nickel.

Jan 1, 1958

By R. H. Storch

The work described in this report was part of a Bureau of Mines program to appraise the titanium-mineral resources of Idaho. Part of the program included churn drilling of alluvial deposits that previous preliminary testing, primarily for rare minerals, had indicated to be potential sources of titanium minerals. The first spot churn drilling began in the Deadwood placer area, Valley County, Idaho, in July 1956 to determine both the amount and grade of the ilmenite, FeTi03. Ten holes, ranging in depth from 6 to 40 feet and aggregating 251 feet, were drilled; 54 samples were taken. The samples were sent to the Spokane field laboratory for concentration and visual estimation of the amounts of the more common minerals in the heavy sand concentrates. For specific determinations samples from each drill hole were composited and shipped to the Bureau of Mines laboratory in Albany, Oreg., where petrographic, quantitative X-ray spectrographic, and chemical analyses were made.

Jan 1, 1958

By D. E. Wolfson

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. According to the estimate of reserves by Dowd,3/ the recoverable coal in Floyd County in beds 28 inches or more thick, in thousand tons, is as follows: [ ]

Jan 1, 1958

By Walter E. Lewis

The Cuyuna iron range in Crow Wing County, Minn., is the principal producer of manganiferous iron ore in the United States. The ore is mined from a manganiferous iron formation in the bedrock of the Cuyuna district. This iron formation is divided into two general lithologic types-thin-bedded and thick-bedded. The unoxidized, thin-bedded iron formation is composed of iron silicate with associated fine-grained carbonates of iron and manganese. The thick-bedded iron formation carries iron and manganese oxides with intimately associated silica. Oxidation and leaching of the original iron formation have been the most influential factors in producing manganiferous iron-ore concentrations in quantities large enough to exploit on a commercial basis. The unoxidized and the partly oxidized and enriched iron-formation materials are suitable as a source of ferrograde manganese ore. These materials have been classified according to their amenability to mineral dressing and degree of oxidation and leaching.

Jan 1, 1958

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4/ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous .sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1958

By G. C. Lammers

The object of this study was to determine the economic feasibility of hydraulically transporting Sandow (Tex.) lignite 100 miles and dewatering and thermally drying the transported lignite to a surface-dry condition. The most important factors involved in the feasibility of hydraulic transport, are the degradation incurred during transit, the length of the line, and the cost of alternative methods of shipment. In pipeline tests in which roughly 75 miles of hydraulic transport was simulated the percentage of minus-325-mesh solids increased from about 1 to 41 percent for both lignite and bituminous coal; in the micron sizes the coal fared considerably better than the lignite. Such degradation, even though it enhances flow through the pipe-line, severely aggravates the dewatering problem on lignite. Cost studies indicated that continuous vacuum filters offer the most economical means of dewatering minus-1/8-inch material. Surface moisture, if high, must be removed by relatively expensive thermal drying.

Jan 1, 1958

By T. E. Gray

This report describes the preparation characteristics of the more significant coals in Dickenson County, Va. It is one in a series planned to determine which coals are suitable for the production of metallurgical coke either as mined or after beneficiation. Nearly 4 million tons of coal was produced in Dickenson County in 1955, of which approximately 2.7 million tons was cleaned mechanically in 5 cleaning plants. The Federal Geological Survey has estimated that nearly 1,300 million tons of measured and indicated coal reserves remained in the county as of January 1, 1951.

Jan 1, 1958

By E. E. Creitz

Application of the usual chemical methods to the determination of beryllium in the mineral-dressing products of a spodumene pegmatite was found to be unsatisfactory as to speed, accuracy, sensitivity, and range of analysis. A spectrographic method is described for the determination of beryllium. Samples are ground, mixed with borax, high-purity, flake graphite, and an internal standard; then they are fused, reground, pelletized, and excited with a high-voltage-spark discharge. Investigation of several spectrographic techniques to overcome matrix effects are described. The method developed gives results for beryllium in the concentration range from 0.002 to 5.0 percent; the average probable error of duplicate determinations was below 3.0 percent of the quantity present. INTRODUCTION The main source of beryllium in pegmatite is the mineral, beryl. Many of the conventional methods for the determination of beryllium in beryl are not suitable for control purposes because of lack of speed and accuracy, especially in the range below a few tenths percent. Beryl resists the usual chemical attack and can be lost in a hurried chemical analysis.

Jan 1, 1958

By A. L. Engel

High extractions of lead, gold, and silver resulted from treatment of an oxidized, arsenical refractory ore by chloride volatilization. The ore was roasted in an oxidizing atmosphere at 1,000° C. for 1 hour. The chloridizing reagent was 300 pounds of CaC12?2H20 per ton of ore. Ninety-nine percent of the lead, 98 percent of the gold, and 96 percent of the silver, and only 6 percent of the arsenic, were volatilized. These results indicated that a satisfactory method could be developed for treating this type of ore. Recovery and separation of the volatilized values and developing metallurgical and operating data for this process require further investigation on a more extensive scale. Tests by gravity concentration, flotation, and cyanide leaching did not give satisfactory results.

Jan 1, 1958

By M. R. Geer

American and European practices in cleaning fine coal are strikingly different. The tables, launders, classifiers, and pneumatic devices used in America are seldom employed in Continental Europe, where much of the fine coal is cleaned in feldspar jigs, often supplemented by froth flotation of the extreme fines. This difference in choice of cleaning equipment may be fortuitous, but in large measure can be attributed to a difference in economic factors. Coal being more costly in Europe, there is greater emphasis on efficient cleaning of all sizes, including the extreme fines, and it is common to produce a high-ash middling for "on-site" consumption to avoid any waste of fuel value. The feldspar jig has been found advantageous under these conditions. In the United States fuel coal must be prepared as cheaply as possible, and metallurgical coal must be prepared as efficiently as possible; thus in both branches of preparation practice, any cleaning device that promises greater economy or higher efficiency warrants consideration. The feldspar jig, as employed in Europe, has a much higher unit capacity than the wet table used so extensively here and therefore offers economy in the capital costs of a washery through saving in space. As pointed out by Vissac,4/ the jig operates under automatic control, and therefore can cope with fluctuations in quality of feed. Maintenance costs for a single, large-capacity unit, such as the feldspar jig, would be expected to be lower than those for a battery of low-capacity cleaners. These considerations led the Bureau of Mines to undertake an investigation of the feldspar jig to determine its possible usefulness in this country.

Jan 1, 1958

By R. V. Higgins

This report presents the results of a study of water injection in the HX sub-pool fault block V-B, in the Upper Terminal zone, Wilmington field, California, and is based on data obtained to May 1957. An earlier report3/ describes the results of gas injection in part of the field. The principal purpose of the pilot flood was to determine whether a sand having a permeability of 1,200 millidarcys and containing oil having a viscosity of 17 centipoises could be waterflooded effectively. The results of a preliminary study by engineers of the Long Beach Harbor Department of oil recoveries from areas where encroaching edgewater was active and the results of an independent study by a consultant retained by the Long Beach Harbor Department were favorable to a trial waterflood. After these preliminary studies, a detailed petroleum-engineering exam-ination was made of the technical details. As a result, a peripheral flood was started in June 1953. The peripheral flood was deemed desirable because the producing wells are bottomed a short distance from the edgewater. The HX subpool was selected for the pilot test because it is an isolated section of the Upper Terminal zone and is separated from the adjoining pools by faults on the east and west and by edgewater on the north, south, and west. Several petroleum-engineering methods were applied to evaluate the performance of the waterflood, and all showed that injecting water stimulated oil production.

Jan 1, 1958