Search Documents

By P. J. Closmann

Steam zone growth as a function of time has been calculated for the case of constant rate steam injection into a preheated reservoir. To simplify the calculation a linear temperature profile has been assumed in the cap and base rock at the start of steam injection. The results indicate that at early times augmentation of steam zone growth due to preheating should be greatest. At longer times the steam zone development becomes close to that calculated with no preheating. INTRODUCTION With the increasing application of thermal recovery processes to recover viscous oil, cyclic steam injection has become important in many large-scale projects. In this process, the cycle of steam injection followed by oil production is repeated a number of times. At the beginning of the second and later cycles, steam is injected into a reservoir that has already been heated but that has lost part of its heat both in produced fluids and by conductive heat loss away from the injection zone. In such a case, the temperature level of the injection zone and the temperature distribution of the surrounding rock will affect the growth of the steam zone developed during the subsequent steam injection. Knowledge of the size of steam zone developed is important in determining the amount of oil displaced and the extent of heating in the reservoir. It is also useful to be able to compute the size of the steam zone for cases where thief zones take most of the injected steam. This paper presents a fairly straightforward method of estimating the steam zone developed in a preheated formation, based on certain simplifying assumptions. Some cases of steam injection into a reservoir at its original temperature have already been considered elsewhere.1-3 Because it is difficult or impossible to obtain an accurate representation of the temperature distribution in the reservoir some time after initial heating has taken place, in this work, a linear temperature profile in the cap and base rock is assumed (Figs. 1A and 1B). The linear profile has the advantage of yielding heat flow equations that

Jan 1, 1969

By Robert G. Nisle

The classic theory of pressure build-up in shut-in oil wells as developed by Horner and van Everdingen is based on two-dimensional radial symmetry in the well-reservoir system. Such symmetry does not exist in the case of a well which parfiially penetrates the producing formation. As a result of this lack of symmetry the use of the classic theory in such cases become questionable. In this paper the mathematical theory has been extended to include the case of partially penetrating wells. Numerical solutions illustrating the up-dication of the equations are presented. The effect of partial penetration on pressure build-up is shown by a comparison of synthetic pressure build-up curves derived from the numerical solution of the equation for partially penetrating wells for various degrees of penetration. It is shown that partial penetration is detectable from the characteristic shape of the pressure build-up curve and that formation productivity may be calculated from the pressure buildup data in a manner identical to that described by the classic theory. INTRO DUCTION The use of pressure build-up data on shut-in oil wells is a well-established technique for the measurement of reservoir productivity. The work of Homer' and van Everdingen' is well known. Since the publication of their pioneering work, others"' have elaborated and extended the technique. These authors have dealt exclusively with the case of wells that completely penetrate he producing formation. Two-dimensional radial symmetry is achieved, thereby, and the problem is greatly simplified. This ideal situation is seldom encountered in practice. But, in spite of this, the technique is often employed anyway. The question, therefore, arises: how much confidence can be placed in the results of such calculations when the data are taken on wells that only partially penetrate the producing formation? It is the purpose of this work to answer this question. Only the single-phase fluid case will be considered. van Everdigen' has presented a rigorous solution of the two-dimensional case, but because of mathematical complexity, this solution has not proved to be particularly useful. Horner' utilized Kelvin's point source solution in two dimensions and showed that it is a sufficiently good approximation for oil reservoir studies. The geometry of the well and the producing formation is illustrated in Fig. l. Geometrically the formation may be described as an infinite slab. The infinite slab is defined as the solid (the porous medium in this case) bounded by two parallel planes. Thus, the slab extends to very great distances in both the positive and negative directions of two of the coordinate axes, but is finite in

By M. Prats

Most of the information available on the heat efficiency of hot fluid injection processes, both water and steam, has been obtained from calculated temperature distributions in the pay zone and adjacent formations. The usual approach has been to write the heat balance equations in terms of the temperatures, and then to introduce whatever simplifications are necessary to help obtain an analytical or a numerical solution. In either case, the assumption has often been made that the vertical thermal conductivity in the flooded interval is infinite, so that the temperatures within the flooded interval are then independent of vertical position. Because it was first made by Lauwerier,l and has been used extensively since, this assumption will be referred to as the Lauwerier assumption. Excellent reviews of the literature on the heat efficiency of hot fluid injection processes have been given by Spillette,2 Flock et al.,3 and Ramney.4 Of course, the most significant contributions take into account the effect of a finite vertical thermal conductivity on the vertical temperature profile. The most general analytic expression for the heat efficiency of a hot fluid injection process is that of Antimirov5 who considers injection of a heated incompressible fluid into a reservoir through an arbitrary number of wells. The rate of heat injection into the reservoir, as well as the injection temperature, is an arbitrary function of time. The geometry of the horizontal flow is arbitrary, although the reservoir is considered to be of uniform thickness and properties and to be of infinite areal extent. Heat transfer within the reservoir is by horizontal convection and conduc- tion, and by vertical conduction. In the formations adjacent to the flooded interval, heat transfer is by conduction in any direction. Thus, the available expression for the heat efficiency due to hot water injection has been developed for rather general conditions. This degree of applicability has not been obtained for other thermal recovery processes. By making the Lauwerier assumption we have been able to obtain expressions for the heat efficiency that are essentially independent of the thermal recovery process, be it steam, hot-water, or underground combustion. Clearly, then, the approach followed here is more restrictive than that of Antimirov5 in that it uses the Lauwerier assumption. At the same time less restrictive assumptions are made about the horizontal heat transfer mechanisms, either in the flooded interval or in the formations adjacent to it. The main difference between our approach and that of other investigators is that the heat balance in the pay zone is expressed for the pay zone as a whole rather than for a volume element within it. The Lauwerier assumption is introduced after the problem is developed along these lines as far as possible. The details of the development of the heat efficiency are given in the Appendix, while the main features of the model are discussed in the next section. Results and their implications are discussed later in a separate section. The Model Certain assumptions have been made to determine

Jan 1, 1970

By H. T. Kennedy, S. M. Avasthi

An equation developed for gaseous hydrocarbon mixtures predicts molal volumes with an average absolute deviation of 0.73 percent when applied to 264 natural gas and condensate systems including 2,043 PVT points. Another equation developed for liquid hydrocarbon mixtures predicts molal volumes with an average absolute deviation of 1.12 percent when applied to 346 crude oil systems including 1,759 PVT points. Both equations require composition of the mixture to be expressed as mole fraction of methane through heptanes-plus, hydrogen sulfide, nitrogen and carbon dioxide, together with the characteristics of the heptanes-plus fraction in addition to the temperature and pressure. The equations cover wide ranges of the variables involved, and their accuracy is considerably better than that of other available methods. The equations were differentiated to allow calculation of the coefficients of isothermal compressibility and isobaric thermal expansion. (In this paper the coefficient of isothermal com-pressibility and the coefficient of isobaric thermal expansion will be expressed as compressibility and thermal expansion coefficient, respectively.) Equations to calculate these quantities are presented. INTRODUCTION Calculations of reservoir performance for petroleum reservoirs require accurate knowledge of the volumetric behavior of hydrocarbon mixtures, both liquid and gaseous. Compressibilities are required in transient fluid flow problems, and thermal expansion coefficients are important in thermal methods of production. An accurate laboratory investigation of the PVT behavior of each reservoir fluid encountered would be costly and time consuming. For this reason various correlations for predicting fluid properties have been developed and recorded in recent literature. Correlations have been presented in the form of graphs, tables and equations. Since an increasing number of studies are being conducted with the aid of electronic computers, recent efforts have been directed toward development of correla-tions suitable for computer programming. Application of computers permits the use of more complex correlations which otherwise are not feasible. Moreover, methods for predicting reservoir performance, particularly those based on the compositional material balance, depend upon the capability of accurately expressing the molal volumes and other fluid properties as functions of pressure, temperature and composition. The coefficient of isothermal compressibility c is defined by

Jan 1, 1969

By F. J. Fayers, R. L. Perrine

For many years the problem of increasing ultimate recovery of oil from a reservoir has been a subject of interest to the oil industry. At present, a standard secondary recovery technique is to flood the reservoir with water once natural forces of the system are depleted. The permeability characteristics of the rock, together with interfacial forces which exist between the two fluids and the porous material. allow only part of the oil in the rock formation to be recovered by the water-flooding process. Laboratory experiments have shown that when detergents are added to the flooding water, the flow properties of oil in a porous rock arc improved. This improvement results in greater oil recovery. Even though higher recoveries are obtained using detergents, the extra cost associated with the method may make it economically unsatisfactory. To establish economic feasibility requires experimental laboratory measurement of fluid and rock properties together with a calculational procedure to predict field results. Pilot tests in the field may also be required. This paper presents a mathematical procedure for predicting detergent flood behavior. A number of reasonable simplifying assumptions are made to obtain a tractable system of equations. The resulting method may be regarded as a generalization of Buckley-Lev-crett' theory to solve simultaneously for water saturation and detergent concentration profiles. Consequently this type of calculation can be used in much the same manner as Buckley-Leverett theory is used to evaluate a water flood. The mathematical method employed is the so-called method of characteristics for solving hyperbolic partial differential equations. This application of the method is instructive because several other problems in reservoir analysis may be analyzed in a similar manner. FLUID FLOW EQUATIONS The flow behavior of oil and water without detergent through porous reservoir rock is usually expressed by Darcy's law and a continuity equation for each phase. If gravitational forces are neglected, vrg = kr (s)µr v p rg.........(1) vrg = kr (s)µr v p rg.........(1) ? pa va = F ?/?t (sd) where v is the volumetric flux, k represents permeability, S is saturation, and P the pressure. Fluid viscosity is denoted by 11, p is the density, 4 is porosity, and I the time. The subscripts w and o refer to water and oil. The capillary forces in the system lead to a difference in pressure between phases. This may be expressed by the relation: Pm -P0 =Pc(S).........(5) The capillary pressure? P,, is determined experimentally as a function of saturation. DETERGENT BALANCE EQUATION Addition of detergent to the water phase affects the flow properties of the system. Capillary pressure and relative permeability become functions of detergent concentration, c, as well as fluid saturation. That is: P--P (S,c) and k,,,.- - -- k,,,. At low oil saturation values, the presence of detergent reduces capillary pressure and reduces the relative permeability ratio. Detergents are surface-active and adsorb on rock surfaces. The quantity adsorbed, a, will depend on the concentration c of detergent solution and may also depend on the saturation; thus, a = a(S,c). In this analysis we have assumed that the detergents used are water soluble but not oil soluble, and their movement is therefore restricted to the water phase. The dispersion of detergent in water is neglected by comparison with transfer by flow within the system. Detergent movement is determined by the water flux and adsorption: ? cv m = -F ?/?t (cs + a) We will assume that the quantity of detergent in solution is too small to significantly change water density or viscosity. When the permeability and capillary pres-

By E. H. Herron, J. H. Perry

Mathematical simulation of reservoir behavior may be used to help understand reservoir processes and to predict reservoir behavior, thereby leading to the most economically desirable form of exploitation. In addition, simulation can be used as a tool for reservoir description to learn more about the physical nature of the reservoir and the mode of primary recovery. This use is essential in most reservoir studies and represents one of the more significant applications of simulation. Prediction of reservoir behavior provides information concerning displacement efficiency, optimum well locations, and the comparison of alternative producing processes. Since oil, water and gas all commonly occur in many reservoirs, a simulation that takes into account the simultaneous flow of three immiscible phases is a prerequisite for obtaining such information. Furthermore, a simulation that describes this flow in two dimensions provides the capability of evaluating combination gas- and water-drive reservoirs with either an areal or a cross-sectional description. Many reservoir problems require such a simulation. The objective of the research described here was to develop a mathematical model and associated computer program for accurate, efficient, and economical prediction of the reservoir flow of three phases in two-dimensional geometry. Several authors have discussed multidimensional reservoir simulation of two phases.l-3 Gottfried et al.' presented an analy- sis of three-phase simulation in one dimension. Fagin and Stewart" and Garrett6 have discussed the simulation of three-phase flow in two dimensions, but their solution techniques were different from the method discussed in this paper. In particular, previous models and computer programs have usually involved either fewer capabilities or inefficient and less rigorous descriptions resulting in limited applicability. In the following sections, we present a description of the model, an evaluation of the method, and the application to reservoir problems. Additional and supporting material is presented in the Appendix. The Three-Phase Model General Description The three-phase model consists of the mathematical description of the flow of oil, water and gas in a reservoir. Conceptually this description considers flow in all three space dimensions, but in the subject simulator it is assumed that no flow occurs in the third dimension. The model includes the effects on reservoir behavior of fluid and rock compressibility, viscosity, gravity, capillary pressure, relative permeability and gas solubility. Within the two-dimensional restriction, the reservoir considered may be completely heterogeneous and anisotropic. The differential equations governing multiphase, multidimensional flow in a reservoir are too complex to be solved analytically, so they are approximated by a system of finite difference equations and solved

Jan 1, 1970

By K. E. Gray, M. S. Seth

In Part I of this work,1 equations of elasticity were formulated for transversely isotropic, axisymmetric, homogeneous, porous media exhibiting pore fluid pressure. Equations of elasticity and the thermal analogy method were used to determine transient horizontal, tangential, and vertical stresses and radial displacement in a semi-infinite cylindrical region when either a constant rate of pressure or a constant rate of flow is maintained at the wellbore. In this paper, the approach presented earlier is extended to finite reservoirs for the cases of (1) steady-state flow, (2) constant pressures at the well bore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Results of this work show that radial and tangential stress gradients are high near the wellbore but diminish rapidt; away from the well; the vertical stress gradient behaves in the same way but is less severe. Radial stresses are compressive or neutral, whereas tangential and vertical stresses may be tensile, neutral or com-pressive, depending upon the boundary conditions, the physical Properties of the system and the radial distance involved (vertical stresses are always compressive in an unbounded system1. For constant boundary pressures, both radial and tangential stresses increase with time whereas they both decrease for a closed outer boundary and constant pressure at the wellbore. The vertical stress decreases with time for both systems. For steady-state systems, radial displacement may be positive or negative, depending upon the dimensions of the system, the pressure differential and the porosity. Radial displacement may be positive or negative for a closed outer boundary but is positive for constant pressures at both boundaries. INTRODUCTION The importance, utility and complexity of a realistic appraisal of the stress state at and local to a wellbore were indicated in Part I. In this paper the analytical approach presented earlier is extended to finite, cylindrical reservoir geometry for the cases of (1) steady-state flow, (2) constant pressures at wellbore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Other than the outer boundary of the reservoir being finite, the physical system and assumptions pertinent thereto are the same as before. The reader may wish to review the mathematical development through Eq. 49 of Part I before proceeding here. SOLUTION FOR GENERAL BOUNDARY CONDITIONS THERMAL STRESSES AND DISPLACEMENTS Since normal stresses do not exist at the free boundaries of a system subjected to thermal stresses, the boundary conditions are

Jan 1, 1969

By A. G. Spillette, R. L. Nielsen

The purpose of this paper is to further the understanding of reservoir response to hot-water injection by desuribing a two-dimensional, mathematical model of the process. Key assumptions are that no gas phase is present, and that the injected fluid reaches thermal equilibrium instantaneously with the reservoir fluids and sand. The resulting system of three partial differential equations is solved simultaneously through the use of a "leap-frog" application of standard alternating direction implicit methods for the solution of the mass-balance equations and the method of characteristics for solution of the energy-balance equation. The utility of the mathematical model is demonstrated by comparing numerical and analytic temperature distributions for hot-water bank injection and by comparing calculated with observed field behavior. Additional calculations show that hot waterfioding can recover significantly more oil than cold waterflooding, and that a hot-water bank recovers, with less energy input, nearly as much oil us continuous injection. Introduction Consistent field success with hot fluid injection processes requires good reservoir description and a thorough understanding of recovery mechanisms. The latter is fostered by a combination of well designed experimental studies and physically sound mathematical modeling. The purpose of this paper is to further the understanding of reservoir response to hot-water injection by describing a two-dimensional mathematical technique, indicating its validity, and demonstrating its utility for studying the effects of reservoir and operating parameters. Published experimental studies of hot fluid injection processes are few." Even if extensive data were available, two considerations discourage exclusive reliance on laboratory or field work. First, because of the severity of scaling requirements," laboratory results must be interpreted with care. Second, because of the one-shot nature of field experiments — injectivity/productivity tests and pilot floods—results seldom are available over the desired range of operating conditions. These factors emphasize the need for devoting attention to mathematical modeling to complement laboratory and field work. Through the use of mathematical models, scaling uncertainties can be bridged and response can be predicted for unique combinations of reservoir and operating conditions. Numerous mathematical models developed during recent years enable us to calculate temperature distributions, thermal efficiency (or conversely, fraction of heat lost), and oil recovery behavior for hot fluid injection. Ramey" and Spillette' recently have provided reviews of these methods. Most models have concentrated on predicting temperature distributions and thermal efficiency; few have been directed at predicting oil recovery.'."1° Although these techniques are useful for estimating effects of reservoir parameters and operating conditions on process performance, results are limited by the assumptions made and by the methods of coupling independently solved fluid-flow and energy-balance equations. A computer-based method is presented for predicting total reservoir response to hot-water injection that obviates most simplifying assumptions. The model simulates fluid flow and heat transfer in two dimensions within a vertical cross-section spanning the oil sand and adjacent unproductive strata. Known numerical procedures are used to solve the governing partial differential equations. The mathematical model handles the effects of reservoir heterogeneity, gravity, capillarity, relative permeability and temperature-dependent fluid properties. In addition, a wide range of operating conditions can be modeled, including hot-water followed by cold-water injection. Mathematical Description of Hot-Water Injection Key assumptions in the mathematical model for hot-water injection are that (1) no gas phase is present and (2) the injected fluid reaches thermal equilibrium instantaneously with the reservoir fluids and sand. Relative permeability and capillary pressure are assumed independent of temperature. Darcy's law for multiphase fluid flow relates the velocities of the oil and water phases to the phase pressure gradients by the following relations:

Jan 1, 1969

By G. E. Warner

This paper presents a review and analysis of a highly stratified Burbank sand waterflooding project in Osage County, Okla. Permeability values in this reservoir range from less than 0.1 md to nearly 3 darcys, and 90 percent of the permeability capacity is contained in approximately 26 percent of the reservoir volume. To date, the project has recovered 103 bbl/flood-acre-ft since waterflood initiation, which represents 50 percent of the total preflood cumulative and 12 percent of the original stock-tank oil in place (OSTOIP). The outstanding feature of this project has been the economical recovery of a sizable quantity of oil at water-oil ratios higher than those normally considered prohibitive. Nearly 70 percent of the recovery to date has been achieved at water-cut values greater than 95 percent. An ultimate waterflood recovery of 138 bbl/flood-acre-ft, or 67 percent of the preflood recovery and 16 percent of the OSTOIP, is predicted. The ultimate primary and secondary recovery will be 302 bbl/acre-ft and approximutely 40 percent of the OSTOIP. The actual performance is compared with the predicted performance by both the Stiles and the Dykstra-Parsons methods, and applicabiliry of these methods to this particular reservoir is evaluated. The performance of this project indicafes highly stratified reservoirs can be successfully and economically waterflooded when either reservoir or economic conditions preclude the use of mechanical and chemical means of mdbility control. Introduction The concept of the stratified reservoir has been used by reservoir engineers for many years to describe the vertical variations in permeability within a reservoir. Numerous techniques have been advanced to predict the expected waterflood performance of the stratified reservoir, and in most cases they prove reasonably accurate. The advisability of undertaking a prospective waterflooding project is determined, based on these predictions. This paper presents a review of a waterflood project in a highly stratified reservoir that normally would be considered a marginal prospect, at best, when evaluated with any prediction technique properly adjusted for reservoir conditions. This kind of project can be successful if the predictions are used to design a waterflooding system capable of economically recovering an oil cut of 1 to 2 percent. Experience gained in the early stages of the project's development was profitably applied in the later development of the entire reservoir and could prove beneficial to other projects with similar reservoir stratification or fracture characteristics. The East Burbank pool waterflooding operations have been developed in three separate stages, each of which has been a separate project: Mid-Burbank Unit, Flood A, and Stanley Waterflood. When referred to collectively, these projects will be called the Composite Project. The Skelly Oil Co.'s Barber lease — the only portion of the pool not included in the three projects — is operated as a separate facility with a cooperative injection-well agreement. It contains less than 80 productive acres and would not significantly affect the over-all performance picture.

Jan 1, 1969

By B. H. Caudle, W. J. Bernard

Factors which influence the success or failure of a waterflood can seldom be determined in the laboratory. For this reason pilot waterfloods are initiated in a repreventative portion of the oil reservoir in question. For a pilot flood to predict quantitatively the recovery to be expected in a field-wide waterflood operation, the pilot area must behave as though it were confined (surrounded by similar areas). In this study, laboratory fluid-flow models were used to determine the simplest pilot pattern, for particular conditions of mobility ratio and initial gas saturation, that would behave as though it were confined. Pilot patterns studied ranged in complexity from a single inverted five-spot to a grouping of nine regular five-spots. Only the innermost producing well in each pattern was studied. Model results showed that the optimum number of wells in the pattern depends upon the oil-water mobility ratio and the expected oil-bank size. Unfavorable mobility ratios will, in general, require more wells in the pilot pattern than will favorable mobility ratios. Pilot patterns in reservoirs which contain a dispersed, flowable, free gas saturation will require fewer wells than for the under-saturated case. The single inverted five-spot pattern was found to be unsatisfactory for predicting behavior of fully developed waterfloods. In particular, it is possible that, in reservoirs which contain a flowable, dispersed gas phase, the oil bank will never be observed at the producers due to the large amounts of free gas which continue to be produced with the oil. INTRODUCTION One method which has been used to predict the performance of a waterflood is the pilot flood. The pilot waterflood is a flood which involves only a small cluster of the reservoir wells and is located in a small, representative portion of the reservoir. The object is that oil produced from the pilot can, in some way, be related to the oil recovery to be expected from a field-wide expansion of the waterflood. However, these field pilot waterfloods have often been unreliable in the prediction of oil recovery in a fully developed waterflood. This unreliability has also been demonstrated in several laboratory studies of pilot floods. Some of the investigators have shown that there are situations in which the pilot flood oil production is far too optimistic with respect to the oil recovery in the fully de- veloped flood. Others4-G have shown that the pilot results can also be pessimistic, especially if the pilot waterflood is initiated in an oil reservoir which has been depleted by primary recovery and is at very low pressure. The major reason for this unreliability of pilot water-floods is the migration of fluids into or out of the pilot area. By the well-known method of images, if straight lines can be drawn to represent vertical planes of symmetry in a porous medium which contains pressure sources and sinks (injectors and producers), then these lines are invariant streamlines, or lines across which there is no potential gradient, and therefore no flow. In an actual reservoir, these lines of symmetry can never be established exactly because of reservoir inhomogeneities and irregular reservoir boundaries. However, if the reservoir is relatively large and contains wells in repetitive patterns, these lines of symmetry are commonly assumed to exist for the pattern units sufficiently far removed from the reservoir boundary. Lines of symmetry for the five-spot injection pattern are shown in Fig. 1. Each five-spot unit in this figure can be considered confined with respect to flow across its boundary. In pilot floods this is not the case. The lines of symmetry for the pilot patterns investigated in this study are shown in Fig. 2. It is obvious that the fluid within these pilots is not confined and is therefore able to migrate into or out of the pilot area. Intuitively, one can see that, if more wells are added to the pilot, the innermost unit tends to behave more and more like the confined pattern. However, there is a practical limit to the number of wells which should be placed in the pilot. This limit is usually determined by economic factors. It was the purpose of this study to use laboratory fluid-flow models to determine which of the previously mentioned pilot patterns will force the innermost producing well to behave as it would in a fully developed waterflood. Since fluid migration is influenced by initial saturation conditions and the mobility ratio, these factors were included in the study. The ultimate objective of this study was to develop data which would allow the operator to choose a pilot pattern and operating conditions that will yield a production history which can be applied directly as an estimate of the performance of each production well of the fully developed waterflood. BASIS FOR THE STUDY The basic problem of field pilot floods is the migration of the reservoir fluids into or out of the pilot area. This problem has been the subject of previously reported model studies on pilot floods. These studies have been concerned mainly with the development of arbitrary "correction factors" to be applied to the simple, unconfined pilot systems such as the single five-spot. The correction factors were intended to adjust the production history of the un-

By W. E. Stiles

A method is presented for predicting the performance of water flooding operations in depleted, or nearly depleted, petroleum reservoirs. The method makes use of permeability variations and the vertical distribution of productive capacity. From these two parameters can be calculated the produced water cut versus the oil recovery. Derivations of the mathematical analogy is shown and sample calculations and curves of prediction are presented. Comparison is made of the predicted and actual performance of a typical 5-spot in an Illinois water flood. INTRODUCTION The use of water as a flooding medium in both depleted and "flush" oil reservoirs is gaining greater recognition and acceptance. Many of the shallower fields, depleted by primary production, have been and are being subjected to water injection in order to obtain some part of the large volume of oil remaining after primary production. Some of the earlier water flood installation proved highly discouraging and the value of water flooding was often questioned. Many of these earlier floods were haphazardly selected and developed as little was known of the physical characteristics and contents of the producing formations. The prior evaluation of the flood performance was impossible. During the past decade the development of the required reservoir engineering tools-—core analysis, reservoir fluid analysis, electric logs, fluid flow formulae, etc.—has allowed the engineer to construct and apply the methods which are presently being used to evaluate the economic and mechanical susceptibility of a reservoir to flooding. This discussion will present a method for taking into account the effect of permeability variations in predicting the performance of water floods in depleted reservoirs. PERMEABILITY AND CAPACITY DISTRIBUTION It is generally agreed by most investigators that in a single phase system fluid will flow in a porous and permeable medium in proportion to the permeability of the medium. Producing formations are usually highly irregular in permeability, both vertically and horizontally. However, zones of higher or lower permeability are often found to exhibit lateral continuity. Thus, while structurally comparable stringers in adjacent wells may differ several fold in permeability values, they usually bear resemblance as being part of a general continuous higher or lower permeability section. It is generally agreed that where such stratification of permeability exists, injected water sweeps first the zones of higher permeability, and it is in these zones that "break-through" first occurs in the producing well. It is a basic assurnption of the presently described method that penetration of a water front follows the individual permeability variations as if such variations were continuous from input to producing well. This is admittedly not rigorously true, but can be justified as making possible a simplifying mathematical approach to an otherwise extremely complicated three dimensional flow problem. As a basis for study of the lateral flow of fluids in formations of irregular permeability, the irregularities may be conveniently represented by a permeability distribution curve and a capacity distribution curve. In obtaining these curves, the permeability values, regardless of their structural position in the formation, are rearranged in order of decreasing permeability. If these permeability values so arranged are plotted against the cumulative thickness, a permeability distribu- tion curve is obtained. This curve may then be likened to a "smoothed" permeability profile of the formation. In making comparison between different distribution curves it is convenient to state the permeabilities in terms of the ratio of the actual permeability values to the average permeability of the formation. These ratios termed "dimensionless permeabilities", are used in this paper rather than the permeabilities in terms of millidarcys. The capacity distribution curve is a lot of the cumulative capacity (starting with the highest permeabilities) versus the cumulative thickness. The capacity and thickness are given as fractions of the total capacity and thickness. Mathematically, the capacity distribution is the intergration of the permeability distribution curve. In practice it is convenient to first obtain the capacity distribution curve and derive from it a smoothed dimen-sionaless permeability curve. The method of obtaining the capacity distribution curve is illustrated in the successive column of Table 1, in which capacity and thickness are derived as fractions of their respective totals. If only a small number of permeability values are available, it is generally desirable to smooth the resultant curve. This has been done to give the capacity distribution curve shown in Figure 1. The differentiation of the capacity distribution curve to obtain the permeability distribution curve is shown in Table 2. Here, the capacity values are read from the smoothed curve at intervals of cumulative thickness, and the increments of capacity are divided by the increments of thickness to obtain the dimensionless permeability, K. Due to this stepwise procedure of calculation these premeability values must be plotted at the midpoints of the successive increments of thickness. The curve so obtained from these data is shown in Figure 1. The total area under the K' curve is equal to unity.

Jan 1, 1949

By W. E. Stiles

A method is presented for predicting the performance of water flooding operations in depleted, or nearly depleted, petroleum reservoirs. The method makes use of permeability variations and the vertical distribution of productive capacity. From these two parameters can be calculated the produced water cut versus the oil recovery. Derivations of the mathematical analogy is shown and sample calculations and curves of prediction are presented. Comparison is made of the predicted and actual performance of a typical 5-spot in an Illinois water flood. INTRODUCTION The use of water as a flooding medium in both depleted and "flush" oil reservoirs is gaining greater recognition and acceptance. Many of the shallower fields, depleted by primary production, have been and are being subjected to water injection in order to obtain some part of the large volume of oil remaining after primary production. Some of the earlier water flood installation proved highly discouraging and the value of water flooding was often questioned. Many of these earlier floods were haphazardly selected and developed as little was known of the physical characteristics and contents of the producing formations. The prior evaluation of the flood performance was impossible. During the past decade the development of the required reservoir engineering tools-—core analysis, reservoir fluid analysis, electric logs, fluid flow formulae, etc.—has allowed the engineer to construct and apply the methods which are presently being used to evaluate the economic and mechanical susceptibility of a reservoir to flooding. This discussion will present a method for taking into account the effect of permeability variations in predicting the performance of water floods in depleted reservoirs. PERMEABILITY AND CAPACITY DISTRIBUTION It is generally agreed by most investigators that in a single phase system fluid will flow in a porous and permeable medium in proportion to the permeability of the medium. Producing formations are usually highly irregular in permeability, both vertically and horizontally. However, zones of higher or lower permeability are often found to exhibit lateral continuity. Thus, while structurally comparable stringers in adjacent wells may differ several fold in permeability values, they usually bear resemblance as being part of a general continuous higher or lower permeability section. It is generally agreed that where such stratification of permeability exists, injected water sweeps first the zones of higher permeability, and it is in these zones that "break-through" first occurs in the producing well. It is a basic assurnption of the presently described method that penetration of a water front follows the individual permeability variations as if such variations were continuous from input to producing well. This is admittedly not rigorously true, but can be justified as making possible a simplifying mathematical approach to an otherwise extremely complicated three dimensional flow problem. As a basis for study of the lateral flow of fluids in formations of irregular permeability, the irregularities may be conveniently represented by a permeability distribution curve and a capacity distribution curve. In obtaining these curves, the permeability values, regardless of their structural position in the formation, are rearranged in order of decreasing permeability. If these permeability values so arranged are plotted against the cumulative thickness, a permeability distribu- tion curve is obtained. This curve may then be likened to a "smoothed" permeability profile of the formation. In making comparison between different distribution curves it is convenient to state the permeabilities in terms of the ratio of the actual permeability values to the average permeability of the formation. These ratios termed "dimensionless permeabilities", are used in this paper rather than the permeabilities in terms of millidarcys. The capacity distribution curve is a lot of the cumulative capacity (starting with the highest permeabilities) versus the cumulative thickness. The capacity and thickness are given as fractions of the total capacity and thickness. Mathematically, the capacity distribution is the intergration of the permeability distribution curve. In practice it is convenient to first obtain the capacity distribution curve and derive from it a smoothed dimen-sionaless permeability curve. The method of obtaining the capacity distribution curve is illustrated in the successive column of Table 1, in which capacity and thickness are derived as fractions of their respective totals. If only a small number of permeability values are available, it is generally desirable to smooth the resultant curve. This has been done to give the capacity distribution curve shown in Figure 1. The differentiation of the capacity distribution curve to obtain the permeability distribution curve is shown in Table 2. Here, the capacity values are read from the smoothed curve at intervals of cumulative thickness, and the increments of capacity are divided by the increments of thickness to obtain the dimensionless permeability, K. Due to this stepwise procedure of calculation these premeability values must be plotted at the midpoints of the successive increments of thickness. The curve so obtained from these data is shown in Figure 1. The total area under the K' curve is equal to unity.

Jan 1, 1949

By C. Özgen Karacan

Degasification and methane control in underground coal mining is an important area augmenting conventional ventilation in order to prevent possible fires and explosions due to excessive methane emissions. Coal bed reservoir engineering has been applied for many years to coalbed methane production. In recent years, modeling the flow and draining methane, not only from coal bed itself but also from the overlying strata, have been recognized as important areas of expertise for supplementing underground ventilation. This paper demonstrates the applications of coal bed reservoir engineering and modeling techniques for optimizing and controlling methane emissions in longwall and continuous miner sections. Practical applications and some considerations are presented for reservoir modeling, borehole performances, and face emission predictions for various coal bed and borehole configurations. A section on field reservoir studies and well bore log analyses for methane control are also presented as a complementary way of controlling methane and optimizing ventilation.

Jan 1, 2009

By B. P. Nutter, M. Lebourg, J. A. McAlister

The Multi-Flow Evaluator (MFE) is a new system of tools providing an original approach in drill-stem testing. It improves control during the testing operation and gives a more accurate evaluation of the fluid recovered while providing additional pressure information for reservoir analysis. The tools are operated entirely by up and down motion of the drill stem. This up and down operation provides a positive means of control and offers easily observed surface indications of tool operating position. An unlimited number of shut-in and flow periods may be taken with this tool while in the hole. The key to the success of the MFE system of tools is the safety seal packer. Until this development, operation of the tools by up and down motion only had proven unreliable. The success ratio of the MFE now exceeds the ratio achieved by conventional tools. The equipment includes a 2,750-cc chamber in which a representative sample of the flowing formation fluid is trapped at the end of the last flow period and brought to the surface under pressure. The sample can be evaluated at the wellsite or transferred under pressure for laboratory analysis. The sampling feature of the tool allows a sample to be obtained from a reservoir which has suffered minimum influence from production. A representative sample can be obtained for laboratory or empirical analysis by employing a testing technique to minimize drawdown during flow periods. Interpretation methods to take advantage of this additional information are presented and supported by actual field examples. INTRODUCTlON The Multi-Flow Evaluator (MFE) represents the most recent technical advance in formation testing. Drill-stem testing techniques prior to the MFE have been limited in three areas—(1) operaiion, (2) recovery analysis, and (3) reservoir analysis. The tools in the MFE system allow maximum control during testing and provide test information superior to that obtainable with conventional tools. The system of tools and the operation procedures are described to illustrate the mechanical advantages over present tools. Methods of pressure build-up and fluid

Jan 1, 1966

By A. M. Khan, I. Fatt

A new type of steady-state thermal conductivity apparatus is presented and described. Results of measurements on Berea sandstone, Solehofen limestone, Bandera sandstone and Bakelite are presented. The measurements were made in a two-hour period at temperatures up to 80C and axial stress to 125 bars. Results show that the thermoelectric heat pump and tbermistor-controlled electric heater can be used in a steady-state apparatus for measuring thermal conductivity of mck. Steady-state is reached within two hours. With Urethane foam insulation, not more than 3 per cent of heat is lost by radial flaw. The apparatus can be used as a comparator or for absolute thermal conductivity determinations. INTRODUCTION Calculations of heat flow through the earth, both for scientific purposes and engineering design, require thermal-conductivity data on rock. However, the high variability of rock often makes handbook thermal-conductivity data of little value. For engineering purposes in particular, it is desirable to have measured data on samples of the rock mass under study. Laboratory methods for measuring thermal conductivity of rock use either time-dependent1-3 or steady - state temperatures .4,5 The time -dependent (transient) techniques give thermal diffusivity from which thermal conductivity can be calculated if the specific heat and density of the sample is known. Most transient techniques require lengthy and involved sample preparation. Also, the accuracy tends to be low. Steady-state techniques are more exact and are the most commonly used. The steady-state methods, however, also have their difficulties. A long time is often required to reach steady state, troubles have been encountered in establishing good thermal contact between the heating and cooling elements and the rock sample, and unaccounted-for heat losses are difficult to prevent. In this paper we present a description of a new type of steady-state thermal conductivity apparatus. With it, measurements have been made in two hours at temperatures up to 80C and axial stress to 125 bars. Sample preparation is simple and no thermal conductivity standard is needed.6 APPARATUS Our steady-state apparatus is an improvement . over the conduction pile used by Zierfuss and van der vliet4 and Somerton.5 A linear heat flux is established through a conduction pile consisting of the rock sample and a standard material of known thermal conductivity in series. The thermal conductivity of the sample is calculated from the ratio of the temperature drop across the sample

Jan 1, 1966

By C. Scala, F. Bernstein

General expressions are derived relating the streaming potential to the electrochemical potential of a permeable junction separating two electrolytic solutions. By the methods of irreversible thermodynamics, these potentials are related to the flux of mobile species arising from differences in pressure and chemical composition. The flux is conveniently expressed as a transference number, the equivalents of a mobile species transferred through the junction per faraday of electricity. At constant pressure, the flux equation gives the electrochemical potential across the permeable junction. The streaming potential across the junction is obtained by imposing the condition of constant chemical composition. The familiar expression for the borehole SP is shown to be a particular solution of the general flux equation. The derived exprersions were verified in experiments with seven shale samples. Both the theory and experimental data provide additional proof of the presence and magniturle of the streaming potential in shales. INTRODUCTION In the interpretation of electric logs, there has been much concern over the correction to be made to the recorded SP for an electrokinetic or streaming potential originating from the difference in pressure between the mud column and the formation. It was long recognized by M. R. J. Wyllie that such an electrokinetic potential source mas in the mud cake opposite permeable sands.' More recently, M. Gondouin and C. Scala2 showed an additional but opposing electrokinetic source of potential to be in shale beds. Their work was supported by the very extensive and excellent work of Hill and Anderson.3 n the present contribution, the general relationships between the electrochemical potential and the corresponding streaming or electrokinetic potential are examined and clarified. A notable advance towards understanding the relation between the various sources of electrical potential in a borehole has been the application of the now common methods of irreversible thermodynamics to describe the passage of ions and water through charged electrolyte junctions such as in shales.' The advantages of these methods are twofold. Unlike classical thermodynamics, they can be applied to non-equilibrium sys- tems, i.e., systems in which flow takes place, provided the flow processes have reached a steady state. They also permit conventional thermodynamic properties to be related to the steady-state dynamic properties. These methods arc used here specifically to derive expressions relating the potential behavior of shales in terms of ion and water transport. Experimental verification of the expression for the shale streaming potential is given which in turn offers theoretical support to the existence of a streaming potential in shales.' Importantly, the relative contribution of transport parameters to the SP is clarified. The theoretical treatment is essentially that of Lori-mer, Boterenbrood and Hermans3 ut has been extended to derive the general expression for the SP.

By J. M. McDowell

A study has been made to deter~r~irre how the behavior of a water drivee reservoir changes as a function of the permeability of the formation and as a function of the size of the aquifer. The effect of pressure maintenance programs on the rote of nat11rn1 water influx is also studied, (IS well as the influence on the influx of the position of water injection we1ls with reference to the oil-water contact. The results are determined by the use of an electrical reservoir analyzer and are plotted as families of curves of pressure, natural water influx, and water injection vs time or cumulalive production. Two size aquifers are studided. One is limited with a 36-inile radius, and the, other approximates an infinite reservoir. The field remains the same in all respects for the completed. study except that the permeability is changed to agree with that assumed for the aquifer. 1 N TR ODUCTI ON this study was undertaken in -dcr to determine how the pres- sure decline and water influx of a water drive field would change as a function of the rate of fluid withdrawals, as a function of the permeability of the formation, and as a function of the size of the aquifer. The effect of pressure maintenance programs on the rate of natural water influx was also studied as was the position of water injection wells with reference to the oil-water contact. The information has been determined by the use of an electrical reservoir analyzer1, sometimes referred to as a Carter type analyzer. This instrument is an analog type computer which can be set up to represent a water-drive oil field. It can reproduce the past performance of the field in terms of analogous electrical quantities when the proper circuit analog of resistors and condensers has been determined, also, it can determine the future behavior for any method of production which may be selected, or permit the comparison among several different methods. Although most applications of the reservoir analyzer"" have been to thc study of specific field performance, it is intended to use the analyzer here to help understand how various reservoir characteristics effect the final performance of the field and to sec under what conditions water injection will be of benefit and to what extent. Within the oil industry the performance of water-drive reservoirs was first described analytically by LV. Hurst' and M. Muskat2 for certain types of boundary conditions. The solutions of the equations developed involved products of exponential functions and Bessel functions. Later publications by Hurst4 and van Ever-clingen" and the hooks of Muskat6 gave further information on reservoirs with other boundary conditions. They also presented rather extensive curves and tables to help evaluate the analytical expressions involved. A rccent series of publications by Chatas. bascd on the work of Hurst and van Everdingen, gives quite complete charts and tables of data to evaluate the pressure decline or water influx in infinite or limited radial reservoirs. and in linear reservoirs. The curves in all of these publications are given in dimensionless form

Jan 1, 1956

By K. Leutwyler, H. L. Bigelow

Jan 1, 1966

By A. Lubinski, C. R. Stewart, K. A. Blenkarn

Storage porosity has been considered one of the important pore geometry characteristics of heterogeneous-porosity limestones. Storage pores are only containers for fluids, in contrast to flow channel pores which both contain fluids and provide continuity for fluid flow. The concept of another geometry characteristic, "poro-striction", is presented as a second pertinent variable in describing limestone pore space. In simple terms, poro-striction is a measure of the flow resistance between storage and flow channel pores. Alternating-flow core-testing theory provides flow relationships which can be used to divide the pore space of heterogeneous-porosity media into flow channel and storage pores and to measure the "porostriction" of the latter. Experimental application of this theory to naturally occurring heterogeneous limestones shows that "porostriction" and the ratio of storage to flow channel pores can be estimated. Porostriction and porosity ratio are microscopic characteristics which should influence oil-recovery efficiencies during certain types of displacement processes. A knowledge of pore geometry should be valuable in designing or selecting the most effective oil-recovery process for heterogeneous limestones containing storage porosity. INTRODUCTION The primary and secondary recovery of oil from limestone (carbonate) reservoirs has been and will continue to be a major source of the world's supply of petroleum. Oil recovery from this type of formation is strongly influenced by the size, shape and arrangement of the pore spaces which hold the formation fluids. Therefore, it is expected that better knowledge of pore geometry would lead to design of more effective recovery processes. The concept of storage and flow channel pores has been presented as an important characteristic of limestone porosity.1 In this concept, storage pores are only containers for fluids, whereas flow channel pores are those pores which both contain and transmit the fluids. The work reported herein involves the concept of an additional pore characteristic called "porostriction". This characteristic can be visualized as the flow resistance between the storage and flow channel pores. This resistance is an important pore geometry characteristic because it determines how easily gas and oil can replenish fluids removed from the flow channel pores. Fatt and co-workers at the U. of California have studied the effect of storage porosity and a factor similar to porostriction on transient-flow response of models of porous media during a pressure build-up or drawdown test.55 These models consisted of porous sandstone cores with artificially simulated storage pores. It is the purpose of this paper to describe tests which permit the storage porosity and porostriction of actual reservoir core samples to be estimated. The tests used for this purpose involved not transient tests but, rather, an alternating-flow technique in which pressure and flow are varied according to a sine-wave relationship. This technique may offer advantages over transient methods. THE POROSTRICTION CONCEPT Before discussing alternating-flow (A.F.) tests in core samples, it is necessary to define the porostriction parameter. For this purpose attention is focused upon an elemental volume v representative of a porous medium having both flow channel pores and restricted-access storage pores. For such an elemental volume, it is considered that the storage porosity is combined to form a single pore and that the access into the storage porosity may be represented by a single capillary tube connecting the single pore to the flow channels of the elemental volume. Let the radius of the capillary tube be designated as Rc and its length as L,. When fluid flows into or out of the pore, the following equation (Poiseuille's law) relates flow rate q to pressure drop p, and the physical characteristics of the tube and the fluid of viscosity jx.

By M. R. J. Wyllie, Michael A. Torcaso

With the continued deep drilling of today, increasing numbers of high pressure and high temperature gas-condensate reservoirs are being discovered. Correspondingly, the ranges of properties of gas-condensate reservoir fluids are also being increased. The literature1*'." contains several excellent reviews of the property ranges in presently known condensate reservoirs. When one examines these property ranges, it becomes apparent that the need for reliable data is great if the engineer is to evaluate properly or appraise a gas-condensate reservoir. It is the purpose of this paper to present phase-behavior data that will point out some of the important variables that influence recovery from gas-condensate reservoirs produced by pressure depletion. All these variables may be resolved into two major categories: the hydroc:arbon composition of the reservoir fluid and the physical properties of the reservoir. But the variables which we will consider are those which are usually determined from well tests shortly after discovery and are, consequently, readily available to the engineer. They are as follows: (1) the producing separator gas-stock-tank liquid ratio, (2) stock-tank liquid gravity, and (3) reservoir temperature. Laboratory depletion studies have been performed on several reservoir fluids to illustrate the effect of changes in the cronsidered variables upon ultimate recoveries. The deviation factors, Z, of a series of reservoir fluids were determined experimentally to illustrate their order of magnitude and their effect upon the calculation of in-place reserves existing at high pressurcs and temperatures. The procedures followed in conjunction with the performance of these studies and their associated calculations are illustrated in Fig. 1. For the purpose of this paper, the depletion recoveries are expressed only in terms of pcr cent of initial stock-tank liquid, with the abandonment pressure assumed to be 500 psig. VARIATION OF RECOVERY WITH INITIAL PRODUCING SEPARATOR GAS-STOCK-TANK LIQUID RATIO The producing separator gas-stock-tank liquid ratio has long been one of the principal criteria in assumptions and generalized correlations' used for the estimation of ultimate recovery from gas-condensate reservoirs. Fig. 2 presents a plot of the cumulative recovery of stock-tank liquid at abandonment as a function of the initial producing separator gas-stock-tank liquid ratio. The graphical illustration represents the results of 44 laboratory depletion studies performed on actual gas-condensate fluids. These data are presented not only to illustrate the general trend of ultimate recovery increase with initial producing ratio increase but to emphasize the considerable variation in possible recovery at any given producing ratio. Table 1 presents the properties of two actual reservoir fluids chosen to illustrate the approximate extremities of producing ratios for gas-condensate systems. The fluids designated as A and B exhibited initial producing ratios of 3,400 and 114,000 scf/bbl, respectively. Fig. 3 presents a graphical comparison of the cumulative stock-tank liquid recoveries, calculated from the well-stream compositions and produced volumes for each fluid during depletion. It is to be noted that Fluid A exhibited a recovery of only 16.5 per cent when produced to an assumed abandonment pressure of 500 psig while the corresponding recovery for Fluid B was calculated to be 62.2 per cent. This difference in recovery, which exemplifies the general trend of recovery increase with initial producing ratio increase, is readily explained by consid-