Search Documents

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"NIOSH recently completed a 15-month study at an underground limestone mine crusher booth which evaluated three research parameters: (1) the effectiveness of a single-filter filtration and pressurization system for improving the air quality inside the operator booth, (2) comparing the effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) evaluating the use of three different pressure monitoring devices to determine the performance of the filtration and pressurization system over time. The protection factor was quantified monthly using particle counters in the respirable dust range (0.3–10 µm), and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static conditions and after outlier removal, the single-filter filtration unit installed offered a protection factor between 8 and 216, depending on the filter type and loading condition. The particle counting analysis shows that the ? > 95 filter offers a protection factor greater than 4-times that of the ? > 99 filter when evaluated over 60 minutes. The booth pressure monitors provided data that proved to be a valid indicator of system performance over time. INTRODUCTION Designed and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from physical hazards, such as flying rock, debris, and noise, as well as a more comfortable environment in regards to temperature and humidity [1]. But while it may be easier to quantify whether the A/C unit is working (measuring the temperature) or observe whether the cab offers protection from flying debris, it can be somewhat more difficult to quantify its performance in reducing respirable dust hazards. For over 15 years, NIOSH has been conducting applied research to improve the air quality inside of enclosed cabs of mobile equipment [2-5]. This work has led to the identification and mathematical modeling of enclosed cab filtration systems [6]. The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms [1, 7]. Stationary enclosures are similar to enclosed cabs; however, the volume of the work area can be significantly larger. In addition, workers who perform their duties in stationary enclosures tend to stay within the room for a greater percentage of the day, as opposed to workers on mobile equipment who may enter and exit frequently. Structural integrity can be easier to maintain as well, as there is typically less vibration and stress placed on these compartments as compared to mobile equipment. In addition to offering protection from dust and flying debris, enclosures must ensure that workers have a healthy supply of fresh air to avoid elevated levels of CO2, which are known to cause headache and dizziness, impairing cognitive function. The American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE) states that enclosures should have no more than 1,100 ppm of CO2 when outside levels are 400 ppm [8]. In addition, the American Society of Agricultural and Biological Engineering (ASABE) recommends a minimum airflow for enclosed cabs of at least 42.5 m3/hr (25.0 cfm) per person [9] to ensure an acceptable level of CO2."

Jan 1, 2017

By A Jewbali, J Phillips, C Boyle

Normal practice in the mining industry is the creation of a single geological model. These models provide a single interpretation of the geological and mineralisation domains. These interpretations infer the exact behaviour of ore domain contacts at shorter scales when resource definition drilling is done on wider scales and are thus locally highly uncertain. The interpreted geological model provides a single number for the volume and tonnes of mineralised material enclosed by the mineralisation envelope. It is on this single number for volume and tonnage that capital intensive mine development decisions (mine design and scheduling, stockpile strategy, waste management, closure planning, dewatering strategy, product quality, etc) are based. Some of these decisions require knowledge of grade variability for small volumes of material such as quarterly production periods. It is generally recognised that this information cannot be derived from single kriged geological models, but can potentially be modelled by conditional simulation techniques. Uncertainty in the extent and continuity of the mineralised envelope and its effect on grade variability for shorter production periods is thus recognised as a major source of uncertainty in new mine development.CITATION:Jewbali, A, Boyle, C and Phillips, J, 2013. Quantifying domain uncertainty for an iron ore deposit, in Proceedings Iron Ore 2013 , pp 157-168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By E Amini, M Scott

Grade Engineering® involves the planning, integration and operation of coarse preconcentration techniques to reject uneconomic material as early as possible in the mining value chain to improve the quality of ore delivered to mineral processing activities. These preconcentration techniques include screening for natural and induced deportment of grade to finer size fractions during blasting and coarse breakage, sensor-based measurements of grade and mechanised sorting at particle or bulk scales and coarse gravity separation. Over the last decade, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE), with the support of its participants, has developed a framework for the holistic evaluation of economic and production impacts attributable to these preconcentration techniques. The framework combines the characterisation of preconcentration responses, geostatistical modelling, process modelling and simulation of downstream and upstream production impacts and the optimisation of strategic mine plans to quantify changes in net present value due to different preconcentration strategies. This framework has been applied to evaluate preconcentration techniques at numerous metalliferous operations and can also be used to quantify changes in the environmental metrics for energy, water and steel consumption and emission, tailings and waste rock production. This paper collates the results of these Grade Engineering® studies to show the range and magnitude of economic and environmental impacts attributable to preconcentration. The studies have shown that rejection of uneconomic material prior to mineral processing activities can have a pronounced improvement in energy, water and comminution steel productivity, emission intensity and the profitability of metalliferous mining.

Nov 10, 2020

By R. Zhang, S. Azam, S. Liu, J. H. Golbeck, V. Kurashov, S. Bhattacharyya

Free radicals (FRs) present in coal dust directly influence the interaction behavior between lung cells and dust particles. FRs are atoms or groups containing unpaired electrons, with strong chemical reactivity and a short lifespan. FRs which are quite persistent in natural environments, termed environmentally persistent free radicals (EPFRs), have recently received much attention as new environmentally hazardous substances. EPFRs present on coal dust serves as an active intermediary to catalyze reactive oxygen species (ROS) production by oxygen molecules endangering mine workers’ health. Many EPFR species may be bonded to the particle surface or trapped within the particle during coalification and can be modified with progressive size reduction through cutting at the mining face or crushing/pulverization in the plant. This study measured EPFRs for lignite, sub-bituminous, and anthracite coal dust at various sizes. We especially focused on EPFRs for submicron coal dust prepared by cryogenic methods. The outcome of this study will directly improve the free radical-dependent toxicity quantification and ultimately contribute to the size-dependent coal dust toxicity quantification.

Mar 2, 2022

By T P. Medhurst

In many cases mine design is the most important driver of the profitability of a mining project, however to reach an æoptimumÆ mine plan many compromises have to be made. Some of the fundamental profit (and loss) drivers relate to stoping methods and stope design parameters. Inevitably trade-offs have to be made between the stability of underground openings, ground support costs and production efficiency. This paper looks at the role of geomechanics in the mine planning and design process. The concepts of æcontrollable lossesÆ and æuncontrollable lossesÆ are developed as a means of partitioning ground control costs. A stope design example is given which provides a method of examining mining costs, and includes a decision making element in order to quantify geotechnical impacts and select stope dimensions. The method also provides a general framework as a means of balancing ground control costs against maximising returns from an underground mining project.

Jan 1, 2000

By S. J. Neethling

"Liberation is a key driver in all mineral separation processes as it limits the maximum possible grade for a given recovery. In flotation, this is further complicated by the fact that it is surface exposure of the floatable minerals that determines the ultimate performance. Liberation, grade and surface exposure are commonly quantified using Scanning Electron Microscopy coupled to Energy Dispersive X-ray spectroscopy (SEM/EDX) analysis of polished sections. The intrinsically 2D nature of this technique can result in significant sampling errors and stereological effects that can affect the quantification of the ore’s textural characteristics. X-ray micro-Tomography (XMT) is an imaging method that can non-invasively and non-destructively delineate ore fragments in 3D, thus providing an alternative method that eliminates the need for stereological corrections and readily provides surface exposure. A methodology and automated algorithm were designed for extracting this information from images of closely packed particles, thus allowing samples containing a large number of particles to be assessed.The main drawback of XMT is that, unlike SEM/EDX, it cannot directly measure the mineralogy of the sample, instead producing a 3D X-ray attenuation map. We therefore also present an algorithm for calibrating the thresholding of the XMT images based on SEM/EDX images of sections through the same sample, thus allowing the liberation analysis to be carried out on a 3D mineral map in which the uncertainty in the mineral assignment is small and statistically quantified.The methodology was tested on low grade porphyry copper ore as this is both an industrially relevant and traditionally difficult system to quantify using XMT due to the similarity in the X-ray attenuation of the sulphide species, especially the pyrite and chalcopyrite. As each 3D volume imaged contain 100-1000s of grains, large data sets can be readily produced. By dividing these particles into classes based on both their surface exposure and grade, the extent to which there is preferential breakage of the particles can be assessed—an important consideration if sufficient surface liberation for good flotation performance is to be achieved at coarser particle sizes. It is also shown that erroneous conclusions can be drawn when basing the analysis on 2D sections through the particles."

Jan 1, 2018

By A. E. Lewis

Particle morphology is a term that is used to describe the overall external shape and appearance of particulate solids. From the physical point of view, a precipitated solid is characterized primarily by the size and morphology of the particles (Sohnel andGarside, 1992). If the morphology of the crystal structures is to be related to the processing conditions, then the morphologies need to be quantified in some way. This can be achieved by using surface area measurements as well as fractal dimensions. The key idea is that rugged and indeterminate systems can be described by using a fractional number that describes the ruggedness of the system (Kaye, 1989). In other words, when the complexity of a structure, such as an agglomerate, increases with increasing magnification, it is useful to employ fractal dimensions to describe the structure. Fractal geometry proposes that, instead of attempting to measure the length of an irregular boundary, the rate at which the length of the boundary approaches infinity with increasing resolution should be calculated. Cross-sectional profiles of rugged particles can thus be quantified using the fractal dimension, and a measurement of the ruggedness of the morphology obtained. One of the additional uses of measuring the fractal dimension is that the measured value can be related to the physical properties and formation characteristics of the particle (Kaye and Trottier,1995). The morphology of nickel crystals was quantified with fractal dimension calculations of particle cross-sections. Particle cross-sections were obtained by mounting the particles in resin and polishing back. These were then photographed using Scanning Electron Microscopy and the resulting profiles analysed using the structured walk technique.

Jan 1, 2001

Surface subsidence that results from longwall mining can be large magnitude and can affect significant areas. Conventional methods for subsidence monitoring include leveling, global positioning system (GPS), and photogrammetric surveys. Remote sensing techniques, including aerial LiDAR, terrestrial laser scanning, and satellite-based differential interferometric synthetic aperture radar (DInSAR), are also used to measure deformation associated with subsidence. DInSAR data are different than data from conventional subsidence surveys. Images capture data over large areas (hundreds of kilometers), and each pixel (data point) in an image quantifies the average displacement over an area of square meters. DInSAR data can have fairly high time resolution; imaging periods typically range from weeks to months.

Jan 7, 2020

By G Gilchrist, S C. Dominy, T Jashashvili, R C. A Minnitt

The grouping and segregation error is one of Gy’s seven errors that cannot be measured in any qualitative manner because of its transient and changing characteristics each time the sample is handled mechanically. Attempts to calculate the mean and variance of the segregation error is considered by some as ‘an exercise in futility’ that would not help us achieve representative sampling. This research is aimed at understanding the process of segregation of dense, finely divided and dilute particulate materials supported in a clean quartz substrate during intense agitation. Several mixtures of fine-grained materials including steel, tungsten carbide and gold grains were used in these experiments. Four hundred grains of each of the minerals and metals at a top size of 2 mm were mixed with approximately 600 g of finely ground quartz material (95 per cent passing 2000 microns) in a 500 ml plastic jar with a sealable lid. The mineral–?metal mixtures were analysed in three steps using microfocus X-ray computed tomography. Step one consisted of rolling the containers on a flat surface in an attempt to concentrate the mineral and metal grains in the core of the supporting substrate; this is a base case that can be reconstructed after each session of analysis. The second step involved gentle and vigorous shaking of the mixtures in order to segregate the denser minerals and metals from the supporting quartz substrate. In some cases, a third step involved splitting the sample through a riffle splitter. Three-?dimensional images of the surface of each grain, its volume and its X-, Y- and Z-coordinates, before and after intense agitation of the container, were interpreted from the reconstruction of the tomographic X-ray data. The spatial analysis of grains using cell declustering and 3D variography provided a useful means of characterising the distribution of the grains in space and the extent to which they had become segregated during the process of agitation. Spatial analysis indicates that in general, grouping and continuity of grains is weakly developed. The modelled nugget effect remains high for most tests, indicating that grains of similar size did not group together strongly. Agitation through rolling provided the best continuity, although not consistently in the long axis of the plastic jar. The nugget effect was consistently highest, and the range of continuity shortest in samples that had been split, indicating that the grouping and continuity were reduced through splitting the sample. Initial results indicate that very little segregation of the minerals and metals occurs in the quartz substrate. This is somewhat counter-intuitive, but suggests that the effects of agitation on mixtures of dense minerals and metals in substrates of lower density do not lead to excessive segregation. Differences in behaviour between dense materials in response to agitation are evident. Grains of different composition and shape did not group and segregate in a predictable manner in response to the agitation methods. Initial results indicate that the degree to which a material groups and segregates relates more to the characteristics of the denser material itself, rather than the agitation method employed.CITATION:Minnitt, R C A, Jashashvili, T, Gilchrist, G and Dominy, S C, 2017. Quantifying segregation of minerals and metals in particulate materials using computed X-ray tomography and variography, in Proceedings Eighth World Conference on Sampling and Blending , pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By K. Taylor

In surface coal mining, the performance of a shovel through blasted muck is one of the key performance indicators of the blast. Historically, performance has been measured qualitatively based on operator feedback or visuals of the muckpile. More complete shovel data, such as loading times and GPS location, is available from most fleet dispatch systems that are already in place at most truck and shovel operations. With some database and analysis skill, the drill and blast team can take advantage of this data to make targeted improvements to drill and blast designs. An area typically known to cause trouble for shovel operators at this operation are blast boundaries. Blast patterns with and without design changes along the boundaries were studied in this case study. The instantaneous loading times for each shovel pass were analyzed for 75 blasts across two subsequent benches with similar firing direction and shovel paths. The benches were split into three categories: Main body of pattern, boundary with design change, and boundary with no design change. The loading times from the main body of the patterns and where the design change was utilized in the boundary had similar prevalence of good loading times. However, boundary areas without the deign change had approximately 2% more prevalence of poor loading times compared to the main boundary of the pattern. Improving the dig rates through the boundaries up to the average loading time would result in approximately 280 hours taken off the total loading time for one bench. By quantifying the shovel’s performance by GPS location, the drill and blast team can decide how much of a design change is needed, can target precisely only the areas that require it and measure the impact of any changes made

Jan 1, 2024

The current methodology to design stope support systems in South African gold and platinum mines is based upon the tributary area concept. The discontinuous nature of the hangingwall rock is not adequately addressed, and mechanisms leading to rock mass failures between adjacent support units are poorly understood. The work reported here aims to formulate a basis for quantifying support mechanisms and gain insights into the influence of rock discontinuities on stable hangingwall spans. Numerical models are used to qualitatively investigate the stress transfer from the support units to the discontinuous hangingwall. Stable hangingwall spans are quantified by considering two failure mechanisms, namely (i) beam buckling, and (ii) shear failure due to slip at the abutments. The output of the proposed design methodology is appropriate site specific support spacing, based on discontinuity spacing and orientation. The method is particularly suited to mines at intermediate and great depth, where typically the hangingwall is highly discontinuous due to face parallel mining induced fractures. Results of parametric studies show that with increasing in situ compressive hangingwall stress, beam thickness and friction angle, hangingwall stability is increased, leading to wider stable hangingwall spans between adjacent support units.

Jan 1, 2000

By P Warner

Mines are often located in remote areas that are not well served by æstiffÆ power grids. Radial transmission networks, high lightning incidence (eg in South Africa the Witwatersrand experiences seven to ten strikes/km2 per year), low short circuit strengths and diesel generation are not uncommon. All these factors result in the electric power supply to many mines being unusually prone to dips and disturbances. æLegacyÆ winder drives û cyclo converters and dc drives û convert power directly from the supply to the motor, with no intermediate energy storage element. Further, they rely on the supply network for commutation and are therefore sensitive to supply voltage disturbances. There is a high probability that a dc or cyclo mine winder will trip during a supply disturbance, often resulting in lost production time and call-outs for technical staff to reset or even repair equipment. In contrast, a voltage source inverter (VSI) ac drive stores a large quantity of energy (in the dc link capacitors) and is fully self-commutating. Hence, this topology is inherently more immune to supply voltage disturbances. Indeed, vendors of ac VSI mine winders make general statements about the superior performance of their drives during supply disturbances. However, the advantages have apparently not been previously quantified. This paper compares different winder drive topologies and their sensitivity to supply disturbances, considers categories of supply disturbances and quantifies the cost of the effects on the different drive types.

Jan 1, 2005

By M. Grodner

Underground excavations exhibit different hangingwall conditions in response to varying geotechnical and mining situations. These differences need to be quantified so as to accurately determine the effectiveness of the mining and/or support strategies. A useful tool for the quantification of these differences is hangingwall profiling. Two methods of hangingwall profile measurement are described?termed irregular and periodic methods. Several data analysis techniques are reviewed for these methods and the suitable ones are discussed in detail. For irregular data the suitable techniques are the determination of the length, the average of the profile and the average absolute deviation from the mean of the profile. All of these techniques as well as determination of the moving average of the height and examination of the spectral image of the profile can be successfully applied to regular data. The effect of preconditioning on the hangingwall is discussed as an example and it is quantitatively shown that it results in improvements of conditions. The techniques described allow the engineer to quantitatively identify the appropriate support type or mining strategy and thus represent a valuable decision-making tool. It is suggested that these techniques should be employed on a routine basis by the rock engineers on the mines as part of their geotechnical classification, as well as support manufacturers to quantify the effectiveness of various support types.

Jan 1, 2000

By J C. de Vries

When times are tough in the mineral industry û as they have been for some time û typical responses by mining companies are to cut costs and/ or increase production. The latter is seen to spread fixed costs, thereby also reducing unit costs per tonne mined. However, most mineral deposits respond to increased production rates by lowering ore grades, so the reduction in cost per tonne of ore does not necessarily result in a reduced cost per unit of metal produced. The authorsÆ experience is that this process often leads to a mine plan that is a long way from optimal. Producing to the point where marginal cost equals marginal revenue may work well in a manufacturing operation, but it is not necessarily the best strategy for a mining company with a depleting resource. Variations in tonnage and grade with depth, ore reserve optimism and a variety of other factors conspire to produce variations in production rates and grade that often result in suboptimal outcomes and potential mine failure. Added to this is the focus of industry analysts and senior corporate management on such measures as unit costs and ounces in reserves. This is perceived to have the perverse effect of driving the share price down when strategies are adopted that actually improve the value of the mining operation, and vice versa! Many mine failures can be prevented by a close examination of the tonnage grade curve and an understanding of how margins, net cash flows and resulting business risk change with cut-off grades and rates of production. A few relatively simple analyses early in the evaluation of a project can demonstrate the tradeoffs between the main decision parameters, leading to right-sizing of the operation. Once major commitments to major capital items have been made, and reserves have been publicly reported, optimisation of the operation becomes much more difficult than if it had been done earlier. Such investigations can also identify the upside potential and downside risks associated with factors outside the companyÆs control. Many strategies that may enhance value in the good times significantly increase the downside risk in the bad times. What is often called risk analysis typically looks at superficial issues, and does not evaluate the major factors leading to the potential for financial disaster. This paper illustrates some of these major risks, and demonstrates how they may be fully evaluated so that corporate decision makers can make fully informed decisions that take account of the real risks.

Jan 1, 2003

By C. Samson, R. S. Smith, S. W. Hefford

"Abstract - Time-domain electromagnetic systems are most sensitive to highly conductive targets during the transmitter on-time. Data collected during the on-time is highly influenced by the geometric relationship between the transmitter and the receiver. Unless corrections can be applied for these geometric variations, the ability to correctly detect and identify highly conductive targets can not be fully realized. Variables affecting the relative position between the transmitter and receiver include changes in the position of the receiver with respect to the transmitter, variations in transmitter attitude, and transmitter loop deformation. The level of accuracy in the determination of the relative geometry required to permit complete removal of the effects due to geometric variations is different for each of the variables and is dependent on the depth of the target. The most influential geometric variation involves changes in the relative position of the receiver with respect to the transmitter along the direction of flight; this variable, therefore, requires the highest degree of accuracy. The accuracy required for receiver motions along the vertical direction is roughly one order of magnitude less, and in the lateral direction, several orders of magnitude less. The objective of this paper is to relate the sensitivity of the response to transmitter-receiver geometry to the ability of an airborne, time-domain electromagnetic system to resolve a highly conductive vertical target. This is achieved by a detailed analysis of the effect of the individual x, y, and z distances between the transmitter and the receiver, the transmitter attitude (roll, pitch, and yaw), and transmitter deformation.Sommaire - Les systèmes électromagnétiques en domaine temporel sont particulièrement sensibles aux cibles à forte conductivité durant le temps d’excitation. Les données collectées durant l’émission du transmetteur sont fortement affectées par les relations géométriques entre le transmetteur et le récepteur. Si un facteur de correction n’est pas introduit pour tenir compte de ces variations géométriques, la capacité de ces systèmes à détecter et identifier correctement les cibles fortement conductrices ne peut pas être pleinement réalisée. Les facteurs affectant les positions relatives du transmetteur et du récepteur comprennent les changements de position du récepteur relativement au transmetteur, les changements d’altitude du transmetteur et la déformation de la boucle du transmetteur. Le degré de précision requis pour déterminer la configuration nécesaire pour compenser complètement l‘effet des changements géométriques est différent pour chacune des variables et dépend de la profondeur de la cible. Les changements géométriques qui ont le plus d’influence sont ceux qui font varier la position du récepteur relativement au transmetteur dans l’axe de la ligne de vol; c’est donc cette variable qu’il faut contrôler avec le plus de précision. La précision requise pour le suivi des mouvements du récepteur le long de l’axe vertical est moindre d’environ un ordre de grandeur, tandis que selon l’axe latéral elle est diminuée de plusieurs ordres de grandeur. Le but du présent article est d’établir comment la susceptibilité de la réponse à la géométrie transmetteur-récepteur affecte la capacité d’un système électromagnétique en domaine temporel aéroporté à reconnaître une cible verticale fortement conductrice. Cet objectif est atteint par l’analyse détaillée de l’effet individuel des distances x, y, et z entre le transmetteur et le récepteur, l’attitude du transmetteur (lacet, roulis, tangage) et la déformation du transmetteur."

Jan 1, 2006

By J Seppelt, G S. Lane, E Wang

Newcrest’s Cadia concentrator operated from 1998 to 2012 with a traditional SABC grinding circuit treating Cadia open pit ore. The Cadia comminution circuit was well characterised through surveys and data that are available in the public domain, and became a benchmark standard for the industry and practitioners modelling large SAG mill based circuits. In 2012, the HPGR-based crushing circuit was introduced in front of the SAG mill to increase throughput when treating the Cadia East ore that was derived from an underground block cave. This ore was expected to be more competent and have a coarser run-of-mine size distribution.Numerous previous papers have described the design and commissioning of the Cadia HPGR-based circuit.This paper describes the improvement in comminution energy consumption resulting from the introduction of the HPGR, including identifying the impact of process complexity and an increase in ancillary energy consumption for conveyors, screening, and crushing.CITATION:Lane, G S, Seppelt, J and Wang, E, 2018. Quantifying the energy efficiency transformation at Cadia due to HPGR crushing, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 141–152 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By M. E. Kuchta

Research is currently being conducted at the Colorado School of Mines in the use of high-pressure water for scaling down loose rocks in underground mine openings. In addition to improved miner safety, the adhesion strength of shotcrete applied to rock surfaces treated with high-pressure water is also increased significantly resulting in improved overall support capabilities of the shotcrete layer. Test results show an increase in adhesion strength by a factor of four on a concrete test wall cleaned with water at 21 Mpa (3000 psi) as compared to a surface cleaned at 0.7 Mpa (100 psi).

Jan 1, 2002

By G R. Hancock, W D. D P Welivitiya

is placed in a waste rock dump, which is usually later reshaped to be erosionally stable, initiate and sustain vegetation and ultimately integrate with the surrounding undisturbed landscape. However, it is unclear how this exhumed material will weather and evolve for most sites. Also, there is a lack of data on the weathering of post-mining materials. If weathering is better understood, then there is the potential to improve rehabilitation outcomes. To improve predictions of the evolution of soil properties and weathering-limited erosion, estimating the rate at which fine, transportable material is produced from the weathering of larger, non-transportable particles and the resultant fragment size distribution and how that distribution evolves over time is necessary. This study examines the weathering process for four different coalmine waste rock materials for a Bowen Basin, Queensland site. Materials obtained from various areas of the coalmine were subjected to cyclic wetting and drying and heating and cooling. Particle size distribution and other material properties were explored after each experimental cycle to ascertain how the material changes during the experimental cycles. The particle size distribution data of wet and dry cycles were used as input data in a numerical weathering model to explore the dynamics of the weathering process for each material sample. A Monte Carlo framework was employed to assess the geometry of the weathering products, weathering rate and the number of daughter particles produced within a weathering cycle. Then the SSSPAM Landscape Evolution Model was used to evaluate the influence of weathering on erosion and landscape evolution of a post mining landform. SSSPAM simulations with: (i) active weathering and (ii) without weathering were run for each material. The erosion rate and the overall landform structure were then compared between weathering and non-weathering simulations.

Aug 2, 2023

By A B. Christie, R Barker

Recent studies carried out to support the development of a strategy for the New Zealand mineral industry by the NZ Minerals Industry Association have included investigations of mineral potential, and the development of scenarios for realising this countryÆs mineral potential by 2010. New economic research is applying a general equilibrium model to quantify the opportunity cost of this potential. The model analyses separately four categories of land (private land and three categories of Crown land) and identifies four distinct mineral classes û precious metals, industrial minerals, coal and aggregate. It investigates the economic effect of the increased availability of mineral resources on the mining industry itself, on other industry sectors and on the NZ economy generally, including its impact on unemployment, GDP and household welfare.The analyses suggest that increases in the level of GDP of between 1.9 per cent and 3.4 per cent may be obtained by utilising New ZealandÆs mineral wealth to varying degrees. The mineral industry sectors are significant beneficiaries under all scenarios; mineral output increases by between two and five times its current level. However, the flow-on effects to the rest of the economy, and to households, are also significant. The analyses show that household income, adjusted for changes in consumer prices, can be expected to increase by between 1.6 per cent and 2.7 per cent. This results largely from increased employment.

Jan 1, 2002

By A Fowler

The unpredictability of the location, grade and width of narrow-vein deposits presents difficulties for mine geologists and engineers attempting to estimate, schedule, forecast and mine their deposit profitably. This unpredictability stems not only from the grade distribution within a vein, but also the irregularity of vein geometry in three-dimensional (3D) space. Traditional deterministic methods of modelling vein geometry do not account for the inherent variability of the veins, resulting in significant errors when using limited drill hole information. This paper presents a probabilistic method of modelling narrow-vein deposits using sequential gaussian simulation (SGS), which can quantify this variability and improve production forecasts. Vein geometry, thickness and grade are simulated to provide a number of different equi-probable realisations that each honour the drill hole and face sample input statistics. An example is presented from the Augusta narrow-vein Au-Sb mine in central Victoria, where the simulation results are validated against the input data and survey pick-ups of the veins along ore drives.

Aug 22, 2011