Search Documents

By Thomas M. Barczak, Joe Bower, Jinsheng Chen

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water-to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water-solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

By Christopher J. Bise

INTRODUCTION The control of nuisance water in a mine is extremely important; left uncontrolled, nuisance water can have a severe effect on haulage, ventilation, production, and the health and safety of miners. To control water in mines, a four-step process is followed: (1) prevention, (2) collection, (3) transportation, and (4) treatment. This chapter will be devoted to the collection and transportation of mine water because prevention is usually dictated by pre-mining conditions and initial planning, while treatment is variable and highly site specific. A mine drainage system is nothing more than a collection of gathering points (sumps), machines that impart energy to the fluid (pumps), transportation ducts (pipes), and control devices (fittings, valves, etc.). A pump does not pull the fluid up the suction pipe; atmospheric or external pressure pushes the liquid up the suction pipe to the pump. All references in this chapter will be to centrifugal pumps, due to their popularity for mine drainage. PUMP CHARACTERISTIC CURVES The performance of a pump is plotted on a graph as an indication of its characteristic. To develop the data points, a test facility similar to that shown in Fig. 1 is established. The calibrated Venturi meter is used to measure quantity, the Bourdon gage measures pressure, and the wattmeter measures power input. Various discharge pressures are obtained by throttling with a gate valve in the discharge pipe. Quantity and power are measured at each of these pressure levels, giving the necessary data for plotting the characteristic curves. Fig. 2 shows a typical characteristic curve for a centrifugal pump. Notice that pressure is measured as so many feet of vertical water column above the outlet level, or head. Knowing the quantity (in gallons per minute), head (in feet), and power input (brake horsepower), the pump's efficiency can be plotted based upon the following relationship:

Jan 1, 1986

THE choice of a pumping plant for the drainage of a mine is a matter of such importance that it is obvious that in a short paper it is impossible to go fully into the reasons governing the adoption of any particular type. The author, therefore, proposes to briefly discuss the methods.in vogue, and, as far as possible, to point out the advantages and disadvantages of the numerous systems. The probiem is of extreme importance to the mining engineer, and it appears that in the past sufficient thought has not been given to this branch, as shown by the numerous failures which are encountered.When water is met with in large quantities, the development of the mine depends upon the pumping plant to such a great extent that the most careful consideration should be given before deciding on any particular scheme for drainage. The pumpingplant in a mine should be looked. upon in the light of an insurance policy, and should be treated as such, care being taken that the premium is as low as possibl~, and to ensure this it is necessary that the most efficient plant be secured. Local conditions play such an important part ill the design of a plant that no hard and fast rules can be laid down. When the amount of water to be handled is small, and there is no possibility of any increase...

Jan 1, 1912

By M. L. Brashears

Pine Point Mines is located in the Northwest Territories of Canada, about 500 miles north of Edmonton, Alberta (figure 1). Lead-zinc ore is found in numerous localized deposits along a generally east-west trending reef of Devonian dolomite, about 5 miles south of Great Slave Lake. A pumping-test program was carried out in 1968 to guide the design of dewatering systems for several open pits that are partially or wholly below the natural ground-water levels. The hydrogeologic conditions, methods employed and results obtained are discussed.

Jan 1, 1971

A knowledge of the principles of punctuation is essential to effective and intelligible writing, for the ease and pleasure of the reader, and even his understanding, may depend upon the choice and the placing of punctuation marks. To 'punctuate' is to mark with stops or points; the word comes from the medieval Latin punctuare (punctuatus), which in turn is derived from the Latin punctum, a point. The purpose of punctuation is to show the manner in which the writing is to be understood; to indicate the relations between parts of a sentence and between successive sentences. To some extent "it does for the eye what vocal stress does for the ear", but especially it marks logical relations. Some punctuation marks, such as those indicating admiration, exclamation, and interrogation, are rhetorical as well as grammatical, but most of the common ones are logical or grammatical. My discussion will be confined to grammatical punctuation in ordinary writing. "The problem of punctuation in text matter", as George Summey * says, "is to employ words, points, and paragraph breaks in such a way as to achieve at the same time clearness, proper distribution of emphasis, and the desired kind of movement." The criticism of the punctuation of a sentence or of a group of sentences is not final until the context, within the paragraph, is read. A paragraph is a sentence or a group of' sentences forming an independent unit of the composition; it represents a unit of thought. A multiplicity of paragraphs produces a choppy effect; on the other hand, paragraphs of excessive length are tiresome, because the belaboring of one unit of thought wearies the reader. The aim should be to

Jan 1, 1931

By Pat Wilmoth, Joseph P. Gildner, Dan Nowak, Shane Yanagisawa, Don Z. Painter, Gordon F. Revey

Frontier/Traylor is presently completing construction of twin tunnels for the Tri-County Metropolitan Transit District of Oregon’s (Tri-Met) westside lightrail system. The tunnels are each 4,550 m (14,935 ft) in length and 6.48 m (21.29 ft) in diameter. The 1/3 of each tunnel was driven from the west portal using drill and blast methods and the remaining 2/3 was driven from the east portal using a TBM. The paper describes: The difficulties encountered by the TBM mining the weathered Columbia River Basalts. The execution of drill and blast work despite challenging ground conditions, stringent noise and vibrations specifications, and public relations problems. The excavation and lining of the Washington Park Station 79 m (260 ft) below the park zoo.

Jan 1, 1997

By Armando Díaz

Anteriormente, el objetivo de las organizaciones empresariales era la optimización de los procesos productivos a través de una limitada eficiencia en el mercado. Sin embargo, esta situación ha cambiado, dado que para ingresar al mercado y mantenerse rentable, se requiere una mayor eficiencia y efectividad. Por ello, el presente trabajo describe el punto de equilibrio como herramienta en el proceso de gestión, donde se igualan los ingresos totales y los costos totales a cero. Son tres los métodos utilizados para la determinación en el punto de equilibrio: ecuación, margen de contribución y gráfico. En este sentido, se utiliza el método gráfico ya que define las ecuaciones de costos totales y es fácilmente comprensible a todo nivel.

Sep 13, 2001

W. H. BASSETT, * Waterbury, Conn.-Manganese should not be expected to remedy all the defects that are due to poor melting practice. It is undoubtedly valuable in helping to eliminate porosity in many of the alloys. In the copper-nickel alloys, its use is becoming almost universal, for, beside helping to make sound castings, it tends to hold the carbon in solution in the solidified alloy. GWILLIAM H. CLAMER,? Philadelphia, Pa.-I have found that manganese copper is satisfactory for eliminating sulfur and that it works very well in the crucible and when you have reducing conditions; but in a large reverberatory charge, where the conditions are oxidizing, we were not able to eliminate the sulfur.

Jan 1, 1919

By W. F. Wheeler

IN the study of the coals of Illinois now being carried on by the State Geological Survey, an attempt is being made to determine the most satisfactory basis of comparison between different coals. The following discussion is based upon work done for the survey in the laboratories of the State University and under the general direction of Prof. S. W. Parr. " Pure coal " has been defined by Mr. A. Bement1 as ash- and moisture-free coal, and the use of this " pure coal " as a basis for comparing different bituminous coals has lately been much discussed among engineers in the middle West. By some the B.t.u. of the pure coal is being used to check calorimetric results, and to calculate the calorific value of different coal-samples from the same seam, for which purposes it is necessary to assume-first, that the composition and calorific value of pure coal from different parts of the same coal-seam are uniform, and, second, that these values remain constant after the coal is mined, both of which assumptions there are reasons to believe are inconsistent with the facts. Certain variables are included in pure coal, as ordinarily defined, and disregard of them may lead to serious error. In any event, where delicate shades of difference are involved, no sure interpretation of results can be made, unless these variables be eliminated. As a basis of comparison between coals, ash- and moisture-free coal is much to be preferred to " dry coal," and still more is it to be preferred to " moist coal," as ordinarily reported in analyses. There are, however, two constituents other than ash and moisture which are similar in effect to them, and which

Jan 1, 1908

By Adam Powell, Salvador Barriga, Matthew Earlam

"The inert anode is a key enabling technology for dramatic energy and emissions reduction in extractive metallurgy. In molten salts, the materials challenge is nearly insurmountable: the anode must conduct electrons at high temperature in a pure oxygen and molten salt environment. A solid electrolyte, e.g. zirconia, between the salt and anode removes the molten salt stability constraint, and can act as a container for a liquid metal anode. This can be liquid silver for oxygen-generating inert anodes, or several metals for natural gas-fueled anodes; it is possible to switch between these modes. The solid electrolyte brings several other benefits: it eliminates molten salt contamination of the anode gas, creates a reducing environment enabling low-cost steel vessels, increases current efficiency, and eliminates carbon contamination of the product. New developments presented here, including current collector and low-cost anode designs, amplify these benefits for producing aluminum, magnesium, rare-earths, and other metals.IntroductionReactive metals such as magnesium, aluminum and rare-earths play increasing roles in efficient transportation and clean energy. In response to new fuel economy standards, automotive OEMs are planning large increases in use of aluminum and magnesium to reduce vehicle weight. Rareearth permanent magnet motors and generators exhibit better power-to-weight and efficiency than induction motors and other designs, making this today's primary motor technology for hybrid and electric vehicles, and for wind turbines. Nickel metal hydride (NiMH) batteries with lanthanum are dominant in hybrids. In 2011, transportation comprised 28.6 out of 103.1 EJ of US energy consumption [1] and 1,845 out of 5,471 million metric tonnes (MMT = 109 kg) CO2e of US greenhouse gas (GHG) emissions [1], creating big targets for economy-wide reductions.Unfortunately processes for making reactive metals for these applications are very inefficient and heavily-polluting. In primary aluminum production, Hall-Heroult cell electricity use [2] is more than double the reaction enthalpy due to heat losses through frozen cryolite side-walls and anode gases, graphite anode plants add significant energy use and GHG emissions [2] (see Table 1). Magnesium is even worse: silicothermic reduction by the Pidgeon process in China produces about 85% of the world's magnesium using coal or coke gas [3]. Chloride electrolysis begins with high-purity MgO and requires carbochlorination or hydrochlorination and costly chloride dehydration [4]—rendered unnecessary for aluminum by the Hall-Heroult cell. Production of neodymium and lanthanum with graphite anodes leads to inconsistent carbon content: small cells make 1 kg batches for analysis, sorting and sale by carbon content, with very high labor and analysis costs. And vertical electrodes give no incentive to reduce anode effect: some reports indicate that China's rare-earth metal industry emits more CF4 and C2F6—with global warming potential (GWP) 6500 and 9200 times CO2 respectively—than China's aluminum industry [5]."

Jan 1, 2014

By L. A. Wasselle

The Israel Mining Industries Institute for Research and Development has developed, during recent years, a number of new processes for fertilizer materials. Their phosphoric acid processes, however, are capable of producing an acid of far higher quality than that normally associated with fertilizer grade acid. This paper will discuss two of these processes showing the quality attainable and the capital and operating costs for, U. S. conditions. The Standard IMI Process is based on the acidulation of phosphate rock with hydrochloric acid and involves solvent extraction for the separation of high quality, phosphoric acid from the resulting solution. The IMI Purification Process applies the same solvent extraction technique to the purification of a wet process phosphoric acid from sulfuric acidulated rock. IMI has built and operated a semi-works scale demonstration plant for the standard process. The first commercial plant was started up in; Japan in 1962. This small seven metric ton per day plant is currently producing a furnace quality acid. A larger 50 metric ton per day plant is nearing completion in Brazil. Another 50 metric ton per day plant is under design while a large plant with a capacity in excess of 150 metric ton per day is in the planning stage. Both of the latter facilities are for Israel.

Jan 1, 1966

By A. B. Kinzel

SILICON, unfortunately, is not in the same category as some other metals with respect to the absolute value of the highest purity material prepared. Tucker, in England, and Becket, in this country have devel-oped procedures for the purification of silicon, and Becket's process has made industrially available silicon of a purity of 99.8 per cent or better. However, even the term "silicon metal" may be a paradox to some people, although not more so than the term "amorphous" as applied to silicon. These terms come from commerce, and "metal" is used to distinguish industrially high-purity silicon from ferrosilicon, silicon-aluminum, and other high-silicon alloys. Alloys of iron and silicon with 95 per cent Si or less are known as ferrosilicon, with a designation of silicon content where necessary, and the terns "silicon metal" is invariably applied to the grades containing 96 per cent Si and higher. The Becket method of purification was referred to in a monograph on the Alloys of Iron and Silicon, and the Tucker procedure was described in some detail in that publication.1 In order to get silicon of still higher purity, a sample, prepared by the Becket method, analyzing 99.84 per cent Si, 0.020 Fe, 0.016 Al, 0.005 Ca, 0.025 C, 0.033 per cent 02, 0.006 H2, 0.006 N2, and 0.001 per cent Mn, was crushed to pass a 100-mesh sieve said further purified by a modification of Tucker's procedure. This modification differs from Tucker's method in that after treatment the 100-mesh alloy was centrifuged to remove the last traces of acid. Our directly determined analysis of this purified sample shows: Si, 99.952 per cent; Fe, 0.009; Al, 0.012; Ca, 0.003; C, 0.006; or 99.982 per cent. Silicon by difference equals 99.97 per cent. The variation between silicon by difference and silicon as directly determined is important. Although Tucker mentions the amount of insoluble matter in commercial silicon both before and after his treat-ment, he does not mention the existence of carbon in the alloy; neverthe-less, lie reports silicon by difference. Any final figure as to purity obviously results from agreement between direct determination and

Jan 1, 1939

By Arshad Ali, Mudassar Khan, Waqas Ahmad, Nisar Muhammad, Muhammad Salman

Talc is an important industrial commodity due to its wide-ranging intrinsic properties; however, the presence of iron oxide hinders its industrial utilization. Herein, we report the purification of Pakistani talc through acid leaching assisted by chlorination techniques. Among various acids (i.e., HF, HCl, H2SO4, HNO3, H3PO4, Aqua Regia, H3BO3, and CH3COOH), HF was the most effectual, removing up to 67% of iron oxide at optimized conditions of temperature, 90–95 °C; time, 120 min; HF concentration of 5%; and at a pH of 1. In the second step, chlorination of the talc sample was performed separately by both wet chlorination and dry chlorination. Wet chlorination was carried out using KMnO4 and HCl in slurry phase which shown about 52% removal of iron oxide, whereas dry chlorination with CaCl2 at high temperature attained about 48% removal of iron oxide from talc sample. Further, the wet chlorination of HF leached samples was also performed under optimized conditions which showed up to 87% iron oxide removal. The original and treated talc samples were characterized by EDX and XRD analysis to monitor the changes in the elemental and mineralogical composition of the talc. It can be concluded that HF leaching followed by wet chlorination is an effective method for the upgradation of low-grade Pakistani talc ores.

Aug 9, 2021

By P. Dhar, H. R. Kota, M. Thornhill

Precipitated calcium carbonate is used as a filler and coating material in the manufacturing of paper because of its high brightness and light scattering characteristics. However, beneficiated calcite has similar potential, given the fact that the industrial specifications are already achieved. For paper industries, the requirement is that the desired product should be pure and have a brightness of 93 to 95 percent. A very-high-grade calcite deposit of around 92 percent is located in the north of Norway, which is used as the raw material for ground calcium carbonate (GCC) feed for the paper industries. There is a substantial amount of calcite resource, which has pyrite and pyrrhotite as major impurities. These sulfides, even when present in minor concentrations, impart color to the end product (paper). Removing these minerals is estimated to increase utilization of the deposit by 10  percent, which represents several million tonnes of calcite marble. Due to the requirement for environmentally friendly reagents and chemicals by the mineral industry, fatty di-amines are being tested for pyrite and pyrrhotite flotation. The interaction mechanism of diamine with the main components of the ore were studied and optimum conditions for removal of sulfide impurities are outlined.

By P. Dhar, H. R. Kota, M. Thornhill

A very high-grade calcite deposit located in northern Norway consists of CaCO3 ore with minor silicate and sulphide impurities. Cationic (Tallow-1,3-diaminopropane, Duomeen T) collector has been used in the purification of calcite by flotation with an aim of achieving calcite concentrate for its use in value-added products in a variety of industries. The feasibility of sulphide flotation from calcite by this cationic collector has been initially judged from Hallimond flotation and zeta potential on pure mineral systems and the results illustrate the removal of sulphide from calcite ore at neutral pH region. The adsorption mechanism of diamine on both the sulphide minerals was found to be the same by zeta potential studies. The variations in zeta potential are in good agreement with the adsorption of diamine molecular and ionic species as a function of pH. FTIR studies also showed the adsorption of diamine species in agreement with the zeta potential and Hallimond flotation results. Furthermore, the removal of sulphide impurities with selective flotation by diamine collector was performed in bench-scale flotation with the calcite ore and the results indeed showed that the calcite concentrate could meet the quality requirements for its use in the paper industry for coating and filler purposes.

Purification of Nickel and Cobalt from Heap Leaching Effluents Using Ion Exchange Resins A comparative study among several chelating resins for purification of a heap leaching effluent from a nickel laterite ore has been finished. Chelating resins with iminodiacetate (IDA) and bis-picolylamine (Bis-PA) functional groups, from different suppliers, have been evaluated for their selectivity and loading capacities for nickel and cobalt over impurities. The two evaluated IDA resins, Amberlite IRC 748 and Monoplus TP 207, showed very similar results for both loading capacity and selectivity. Better performance was obtained at 7 BV/h at a pH of 4. Evaluation of Bis-PA resin showed that XUS 43578 has better performance than TP 220, with a 30 per cent higher loading capacity and superior selectivity for nickel over impurities.

Sep 13, 2010

By Georgios N. Anastassakis, Nickolaos Georgiou

"Soil contamination by oil as well as by other organic pollutants poses a major problem to the environment. Various methods have been used to remove organic contaminants from soil, such as: biological, thermal, chemical and physical. Methods based on Mineral Processing principles have also been used (cyclone separation, gravimetric separation, attritioning and washing). This paper studies the possibility to remove a rich-in-contaminant soil fraction by applying flotation. The contaminated soil was artificially prepared by mixing soil with diesel fuel. Sodium dodecylsulfate (SDS) and a tertiary amine (TA) were used as collectors. The effect of collector quantity added and conditioning time was studied. The results showed that the removal of a rich-in-contaminant soil is feasible while a clean fraction is also obtained. In several cases, the removal of oil-contaminated soil approaches or reaches 100%. Introduction Human activities are intimately associated with environmental pollution to the air, water and soil, as well. Soil pollution from inorganic and organic compounds is of equal importance with that of air and water, as it results in soil degradation and its concomitant problems with respect to meeting the human needs (house building, agriculture etc). Heavy metals along with their compounds are encountered among the most usual soil inorganic pollutants. The corresponding organic soil-pollutants are oil, oil-derivatives, pesticides, various aromatic (benzene, phenols, cresols, toluene etc) and poly-aromatic (naphthalene, anthracene etc) hydrocarbons, as well as various other organic compounds (pyridine, cyclo-hexane etc). Oil remains the basic energy source sharing 38% of the global needs, being followed by coal and gas with a share of 26 and 21% correspondingly [1]. The entire activities related with oil production, transport and consumption promote pollution in the air, water and soil. Consequently, soil pollution from oil is favoured at refineries, storage sites (due to possible pipe and tank leakage, tank cleaning works, loading and transportation) and, finally, at the oil-selling sites. Oil (or diesel-oil) fuel is a mixture of hydrocarbons, with 10-20 carbon atoms in the chain of each. It is mainly composed of paraffins, naphthenes and various aromatic compounds. In general, oil is composed of 20-30% in aromatic compounds, 5-6% in naphthenes and the rest is paraffins [1]."

Jan 1, 2008

By Nobuo Takahashi

Effective solvent extraction media have been investigated for purification of rare earths. At first, a quaternary ammonium compound was studied. The counter anions of rare earths and organic dielectric substances were tested to improve separation factors,. And second, crown ethers were selected for extractant. Several diluents of crown-adducts were tested to improve solubility and distribution coefficient as well as the counter anions of rare earths. Especially, in the presence of strong reducing agents, highly selective extraction of europium from other rare earths was observed. The third extactnts were ß -diketones. Presence of organic dielectric substances was very effective to improve separation factors. Though those. three groups of extractants were suitable for mutual separation of light rare earths, alkyl esters of alkyl-phosphonic acids were suitable for mutual separation of heavy rare earths because of their high separation factors. To keep proper pH value was necessary for acidic extractants, so control method of the solution pH was studied with high molecule insoluble amines or salts of those.

Jan 1, 1995

By J. C. Escobedo, J. M. Almanza, A. Flores, Cortés. D. A.

Secondary aluminum dross, which has been exposed for several years to atmospheric conditions, was characterized using chemical analysis, X-ray diffraction, optical and scanning electronic microscopy, and energy-dispersive spectroscopy. Based on the characterization, a method to purify the solids is presented. This method starts with the washing of the dross in boiling water to eliminate the soluble compounds like Na and K, followed by the physical separation of the metallic aluminum by milling and screening. Finally, an acid lixiviation process is applied using three different acid solutions, HCl, HNO3, and H2SO4. The best results were obtained using HCl. The main insoluble components of the dross after lixiviation were Al, SiO2, and Al2O3. MgAl2O4, AlN, Si, and Na2Al22O3·2H20 species were also found. Based on the alumina content, the solid product could be suitable as a raw material in the manufacture of castable refractories or metal matrix composites.

Jan 1, 2005

By S. Fazluddin, K. C. Sole, M. R. Serwale, T. Coetsee

The CSIR-Ti process employs lithiothermic reduction of titanium tetrachloride feedstock to produce titanium sponge. The product is therefore contaminated by a range of lithium and chloride species. In this study we examine the effects of particle size, temperature, and HCl concentration as input leaching variables on the removal of chlorides from the crude titanium sponge. A review of the aqueous chloride chemistry of Li and Ti provided initial conditions for leaching of impurity species from the sponge. Experimental results confirm that the effectiveness of leaching and removal of dissolved impurities from the sponge are dependent on leaching kinetics, which are influenced by temperature, particle size, and morphology. Of the variables tested, reaction temperature had the strongest influence on the oxygen content of the leached product. The HCl lixiviant concentration had a negligible effect under the conditions tested. Leaching of crude titanium sponge (−10 mm size fraction after crushing) at 14°C in either 1 M or 0.032 M HCl yielded a titanium sponge product that met the ASTM standard specification for commercially pure Grade 1 titanium, i.e., oxygen content < 0.18 mass% and chloride content < 0.15 mass%.

Dec 13, 2022