Search Documents

By Wellington Pereira Inácio, Fernando Wypych, Sergio Neves Monteiro, Artur Camposo Pereira, Rafael Marangoni

"The efficiency by which an applied load is transmitted from the matrix to reinforcing fibers in a composite depends on the fiber/matrix adhesion strength. This is determined as the interfacial shear strength, IFSS, which may be measured by means of pullout tests that measure the force needed to pull a single fiber out of a block of material simulating the composite matrix. Different techniques are used to perform pullout tests. The objective of this work was to characterize the IFSS of sisal fibers embedded in epoxy matrix through the determination of the critical length pullout curves. As the main results, a relatively small critical length was found for the sisal fiber/epoxy pullout specimens, corresponding to a weaker IFSS. This was compared to other results applying different pullout techniques. Scanning electron microscopy observation identified the mechanism responsible for the weak sisal fiber adhesion to the epoxy matrix.IntroductionSynthetic fiber reinforced composites is today one of the most successful class of materials with increasing industrial applications from house appliances to large airplanes like the modem Airbus 380. However, environmental issues are revealing serious drawbacks related to the fabrication, use and post-use discard of these composites. For instance, the thermoset polymer composite reinforced with E-glass fiber, known as ""fiberglass"" has an energy-intensive fabrication associated with a surplus emission of C02, which is responsible for global warming [1]. Moreover, the glass fiber is considered toxic and also causes long term pollution after being discarded."

Jan 1, 2011

By V. Castranova, T-M. Ong, V. Vallyathan, M. J. Keane, W. E. Wallace Jr.

"Inhalation of certain forms of silica, asbestos and some other respirable dusts can result in pulmonary fibrosis, characterized by destruction of the surfaces of alveoli and respiratory bronchioles. Fibrous thickening of the alveolar septa decreases the lung's capacity for gas exchange.Pulmonary macrophage damage by respired dust may initiate the fibrotic response.In one proposed mechanism, dust particles interact with the plasma membrane of a macrophage. This damages the cell or induces some hyperactivity of the cell, resulting in excessive release of lysosomal enzymes and reactive forms of oxygen (1). These reactive enzymes or radicals then damage the alveolar surface epithelial cells. A second mechanism has also been pro¬posed (2,3) in which dust damage to the macrophage causes the release of mediator substances which induce pulmonary fibroblast cell proliferation and increased collagen synthesis. This produces fibrous tissue in the terminal air spaces (4,5).Mineral surface interactions with plasma membrane lipoproteins have been proposed as a mechanism of lytic damage of pulmonary cells by silica dust in numerous models (6,7). The significance of dust surface proper¬ties has been further revealed in studies showing significant changes in dust induced cytotoxicity as a function of dust surface crystallinity and organic or inorganic contamination or coating of mineral surfaces (8,9). Such modification of the mineral surface might interfere with surface sites responsible for the toxicity of dusts for pulmonary macrophages, thus interrupting the early stages of the process of fibrosis.In vitro cellular assay systems using erythrocyte hemolysis or the release of macrophage cytosolic or lysosomal enzymes following dust challenge, have been used to analyze the initial mechanism of dust damage to cells. However the ability of these assays to predict the pulmonary disease producing potential of various dusts is imperfect owing to some ""false positive"" results. These assays as performed are therefore questionable models for the initial lesion in pneumoconiosis or silicosis. In particular, kaolin frequently is found to have comparable biological activity to silica quartz in these assays (10,11).Silica and kaolin have distinctly different fibrogenic potentials. Silica is highly fibrogenic, resulting in both acute and chronic silicosis (12). Some epidemiological data and animal experimentation data have indicated that long term exposure to kaolin can result in pneumoconiosis; however, kaolin is relatively benign as compared to silica (13-18). Kaolin is also of interest because it is one of the major mineral inclusions in Eastern U.S. bituminous coals. We have observed that exposing respirable sized native silica or kaolin for two hours to pulmonary macrophages results in a greater enzyme release for kaolin exposures, on a dust mass basis. Exposure of erythrocytes to the dusts also results in greater levels of hemolysis by kaolin for equal mass respirable dust doses. Therefore, these results do not correlate positively with known disease inducing potentials of the two dusts.Characterization of physical and chemical surface properties of dusts involved in occupational exposures, and characterization of the alteration of those surface properties which are likely to occur upon deposition of the dust in the lung, should improve the identification of respiratory disease hazards.Inhaled dust particles deposited in the lower respiratory tract will come in contact with pulmonary surfactant. This surfactant forms a surface film on and emulsion in the liquid hypophase coating of the alveoli and respiratory bronchioles. The primary constituent of this pulmonary surfactant is the lipid diacyl glycerophosphorylcholine, lecithin (19). Because this lipid is also a major component of cell membranes, it is possible that surfactant can interact with mineral dust to alter its Interaction with macrophages and other pulmonary cells and, thus, it"

Jan 1, 1988

By Gordon R. Harris, Raymond Chalk

Descriptions of typical pulp and paper manufacturing processes are presented, with particular emphasis on the use of minerals and derived products. Some consideration is given to the future demand for these minerals by the pulp and paper industry. Possible influences of techno-logical change and social legislation are suggested and their effect on saltcake demand by the pulp industry is discussed. Predictions are made regarding trends for new and existing paper products.

Jan 1, 1968

By Raj Rajamani

In general, many past works examine mill load, mill power, shell lifter design etc with a view to improving the mill capacity. On the contrary, only a handful of papers have addressed the transport of fine slurry through the pulp lifters. We present the flow dynamics of pulp lifters via laboratory scale experiments, high speed photography and modeling with computational fluid dynamics. Next, the flow behaviour in ArcelorMittal?s Mont-Wright autogenous mill discharge flow is examined. In an effort to improve mill throughput, a comprehensive simulation and plant scale study of the mill was taken up with a focus on the shell and pulp lifter design. The shell lifter was found to be at its optimum limit for breakage of ore particles given the constraints of wear life and occupied volume. Next, the pulp lifter study was taken up with computational fluid flow code and discrete element code. The simulations directly showed that there was considerable carry-over of slurry. This effect was traced to the area restriction in the pulp lifter channels. Further, crash-stop studies confirmed slurry pooling within the mill. Thus it was readily apparent that mill throughput can be increased if the pulp-lifter could be redesigned. Consequently, the discharger section of the pulp-lifter was redesigned. First, this paper outlines the modeling in laboratory scale studies and plant scale studies leading up to the discharger design. Next, the discharge flow in seven different published mill surveys is predicted with computational fluid dynamics (CFD) methodology shown here. Finally, Mont-Wright mill circuit performance before and after the discharger redesign is described. The usefulness of fluid flow simulations in the design of pulp-lifters is emphasized.

Jan 1, 2012

By Luzheng Chen

Pulsating high-gradient magnetic separation (PHGMS) of fine hematite from tailings was studied using a pilot PHGMS separator to investigate the possibility of its application in industry. The results of this investigation indicate that PHGMS is effective for recovering fine hematite from the tailings and greatly improved the separation performance compared with the conventional high-gradient magnetic separation at the same conditions. By applying the pilot separator with a 1-mm rod matrix to a tailings containing 28.76% Fe, a concentrate assaying 54.35% Fe with 35.89% recovery was achieved. It was found that the separation performance of the pilot separator closely correlates with the main pulsating parameters, i.e., pulsating stroke and frequency. It was also found that a change in the wire diameter of the rod matrix from 2 to 1 mm causes a weak drop in concentrate grade but results in a considerable rise in recovery. This finding proves that the improved performance achieved by the pilot separator is attributed to the pulsating of slurry and to the use of a 1-mm rod matrix. When the first commercial SLon-2500 PHGMS separator with a 1-mm rod matrix was applied to recover fine hematite from the tailings, the results duplicated those achieved with the pilot PHGMS separator.

Jan 1, 2009

By Erik Vlot

"The mining industry has recognized the advantages of high density backfill or ‘paste’, which is typically pumped with a hydraulically driven piston pump. Due to the discontinuous flow of this type of pump, pressure pulsations can occur in the discharge line. Pressure pulsations are an undesired phenomenon in pumping installations for a number of reasons that include: damage to the pumping system; piping and supports; disturbing noise levels; and even safety risks for operators and maintenance personnel.This paper describes an advanced system on the GEHO® piston pumps, which will prevent virtually no pressure pulsations from occurring, rather than merely reducing the already existing pulsations.INTRODUCTIONThe first GEHO® hydraulically driven piston pump was developed in the mid-1970s. It was an industrial design pump designed to operate in the high-standard industrial environment with regards to operating hours per day, duties, maintenance and lifetime of the pump and spare parts. This type of pump has a proven track record and has been further developed for the type of applications that we are describing today. The special feature of this pump type is its ability to pump extremely viscous slurry with solids content of up to 90% by weight, at high pressures. Typically, in the mining industry, this pump is used for tailings transportation, with a focus on mine backfill and is often referred to as a paste pump.In the 1980’s the hydraulically driven piston pump made its entry into the application of mine backfill, thanks to the high discharge pressure capabilities enabling the mines to pump higher density (i.e. higher solids concentration) slurries and pastes over longer distances.Part of the ongoing development was (and still is) the increase in discharge pressure and flow capacity to comply with the ever growing demands for high power piston pumps. In line with the technological developments and increase in performance duties, the popularity of this pump type increased significantly and many other industrial applications have discovered the benefits of this pump type.Together with the increase in pump discharge pressures and flow capacities the effect of an undesired phenomenon also increased: the phenomenon of pressure pulsations. Before we explore this subject in more detail it is important to first understand the design and the characteristics of a hydraulically driven piston pump."

Jan 1, 2017

By Crone Duncan

The search. for massive sulphide orebodies is steadily being extended to greater depths as well as expanding outward into the large portion of the earth's surface where the sulphide bodies are deeply weathered. Massive sulphide orebodies are generally not large in dimensions. They are not like disseminated type sulphide bodies that form large ground exploration targets that can be detected at greater and greater depths simply by increasing the geometrical spacing between the geophysical transmitter and receiver. In¬creasing the transmitter-receiver spacing with massive sulphide bodies eventually "waters down" the anomaly from the body until it disappears into noise. If high surface conductivity is present, as is common in areas of deep weathering, the problem is compounded by the increasing response of the surface layer, as the receiver-transmitter spacing is expanded. The search to greater depths has important implications other than just detection of the orebody. Drilling costs are increased and the probability of missing the target are increased. Missing an orebody is an expense that is difficult to evaluate in dollars per line mile of survey especially since one does not know the value of what was missed. A ground Pulse EM method has the capabilities of solving the problems of deeper exploration particularly in areas of surface weathering it can attain deep penetration without large coil spacings, it also provides information from a complete range of frequencies. The method has other operational advantages since it is free of geometrical restrictions as to coil alignments and can operate in areas of high power line noise.

Jan 1, 1975

By Valentine A. Chanturiya

The aim of this paper is basically to show progress in the study of nanosecond processes involved in the disintegration and breaking-up of mineral complexes with fine noble metals. We studied the influence of nanosecond High-Power Electromagnetic Pulses (HPEMP) on the physical and technological properties of refractory gold-containing ores and beneficiation products. Experimental data are presented to confirm the formation of breakdown channels and selective disintegration of mineral complexes as a result of pulse irradiation, which makes for efficient access of lixiviant solutions to precious metal grains and enhanced precious metal recovery into lixivia during leaching. Preliminary processing of gravity concentrate with a HPEMP resulted in significant increase of gold and silver extraction into lixivia during the cyanidation stage, with gold recovery increased by ~31% (from 51.2% in a blank test to 82.3% after irradiation). Gold recovery from stale gold-containing dressing tailings products increased after pulses-irradiation from 8-12% to 80-90%.

Jan 1, 2006

E. W. Stutchbury (Internationa~ Oombustion Aust. Ltd.) : Mr. Callcott made particular mention in his paper of erosion in primary air fans which are placed after the mill discharge. He adds that subsequent reduction in plant performance and resulting increased maintenance costs occur. It is generally assumed that this statement is substantially correct as the fan handles the complete output from the mill, but with modern materials, reduction in performance and subsequent .maintenance are not now a problem. This consideration of handling the pulverised coal in the fan is more than offset by the advantage of operating the mill under suction which results in cleaner operating conditions, simpler feeder arrangements and elimination of complicated seals on the mill.and feeder unit. It should be specially noted that whereas mill exhausters in the past have used chequer plate blades (sometimes with the addition of hard facing by electrode deposit) it is modern practice to provide fan blades of up to 1 in·. thick Ni-hard suitablyheat treated, with the circumferential section of the fan also in Ni-hard. By the use of this material large power...

Jan 1, 1957

By N. T. Avard

THE profitable disposal and utilization of much of our slack coal, lignite, and other low-grade fuels is one of the major problems facing the coal mining industry of Canada today. It is my belief that the pulverization process applied to these fuels opens the door to greater efficiency and greater prosperity, and I wish to discuss briefly with you some features of its development and advantages to date. Indeed, the art of burning pulverized coal under stationary boilers is one of the romances of modern engineering. As a Nova Scotian, I feel some pride in the fact that at Chignecto Mines, N.S., was built in 1906 the first pit-mouth power plant on the North American continent. This was built to make effective for the first time Edison's dream of carrying coal for power by wire rather than by rail. This plant, built by the Maritime Coal, Railway and Power Company, Limited, success-fully utilized underfeed stokers for twenty years but in 1927 was replaced by a more modern plant equipped with machinery for burning pulverized coal, which is now operating very successfully. A further source of pride is the fact that the first boilers on this continent to be operated by pulverized coal were installed by the Dominion Coal Company at New Waterford, N.S., in 1912 and were satisfactorily operated during the lifetime of the plant. It is an acknowledged fact that average living conditions on a large part of the North American continent are far superior to those of any other people on earth. The reason is that we use so much more machinery per capita, and cheap power supply has been a large factor in bringing that about. Statistics show that where one horse-power was used one hundred years ago to assist man in his work, five hundred horse-power is used today. Truly a remarkable development and the key to our present high standard of living. Lack of coal in the chief industrial centres of Canada has forced the extra-ordinary development of the water powers which Providence has placed in those centres. How many of us realize that Canada stands second in the world in the per capita development of hydro power, Switzerland being first and the United States sixth? From this condition, we are reminded of the fact that the per capita foreign trade of Canada far exceeds that of our great neighbour to the South-but another illustration of the benefits accruing from our great power development.

Jan 1, 1937

By André Oliveira

The present paper describes state-of-the-art Pulverized Coal Injection technology with focus to Dynamic Distribution guaranteeing highest accuracy on equal distribution and being thus one of the key factors enabling constantly highest injection rates. As an alternative to the construction of a new plant, existing plants may be modernized and upgraded to latest technology. Two recent examples are presented. As a conclusion, two case studies of return on investment are showing that the PCI technology, both for new facilities as well as for upgrades, is very profitable and mandatory for high blast furnace operation effectiveness.

Aug 17, 2017

Brief descriptions of several types of unit pulverizeI' are given and the functioning of the components that crush, carry, dry and classify the coal is considered. A distinction is drawn between pulverizers which crush particle beds and those .operating by free-crushing. The overall performance of pulverijlers is considered in terms of correlations between mill variables, coal grindability, abrasiveness, moisture and particle size. Brief discussioiJ. of the influence of pulverized fuel quality on boiler operation and of pulverizing costs concludes the paper.INTRODUCTIONModern coal pulverizers function as carriers of materials and as crushers, as dryers and as size classification machines and, thus, the unit pulverizer comprises. several components that normally function as separate apparatus. The controls of the unit pulverizer must have sufficient flexibility to accommodate rapid variations of boiler load or coal quality. Further, the machine must be robust, yet easy to maintain preferably at annual intervals-so that maintenance costs are small (for coal is a relatively cheap material). Usually, the full load of a modern pulverized-fuel fired boiler can be raised with one pulverizer off-line. All coals, from anthracites to brown coal, may be prepared as pulverized fuel (hereafter P.F.) .Each pulverizer of a direct-fired boiler has, broadly, to supply the burners with coal powdered so that about 80 per cent passes a 200 B.S. sieve and only a small proportion, less than about 10 per cent, remains on the 100 B.S. sieve. The classification processes must prevent any appreciable proportion of coarse particles in the P.F. and yet not return excessive proportions of "finished" fines. The quality of the P.F. should not vary greatly with output rates which may be anywhere between the maximum rate and one quarter ofthe maximum. The suspension of P.F. in the primary air...

Jan 1, 1957

By Gordon C. ‘Bud’ Presley

The pumice and pumicite review arrived too late for the June issue. Estimated domestic production of pumice and pumicite in 1992 was up compared with 1991, according to US Bureau of Mines statistics. The Bureau estimate of domestic production of 400 kt (440,000 st) for 1991 turned out to be 401 kt (442,000 st) of actual production, the lowest since 1989. In 1992, the estimated the value of pumice and pumicite sold or used in the United States was $11.6 million, up only $200,000 from the 1991 value. There was an increase in the mine, or mill, average price from the five-year low of $11.44/t ($10.37/st) in 1986 to $26.42/t ($23.96/st) in 1992. Estimated tonnage produced in 1992 was 439 kt (484,000 st). Apparent domestic consumption was 642 kt (707,000 st), up 135 kt (149,000 st) from 1991. Imports for consumption were estimated to be 215 kt (237,000 st) last year. Domestic production supplied 68% of the demand in 1992, with net imports supplying the remaining 32%. This compares with domestic production sup¬plying 53% and net imports supplying 47% of the apparent consumption in 1988. Exports were about 900 t/a (1000 stpy) for the period 1984 to 1988. In 1989, exports rose sevenfold to 7 kt (7700 st) and to 20 kt (22,000 st) in 1990. The Bureau of Mines reported that the amount of pumice and pumicite exported in 1992 was 12 kt (13,200 st). It is assumed that these exports were from the Pacific Coast because imports, mainly from Greece, continued to be a market factor on the East Coast and the Gulf Coast States in the United States.

Jan 1, 1993

The design/optimization of the pump and cyclones to maximize grinding circuit efficiency first requires a concise understanding of, and clearly defined specifications for, desired grinding circuit performance. Subsequently, the pump and cyclone performances that provide the desired grinding circuit performance can be defined. Once the performance requirements of each process unit are determined, selection of physical equipment parameters that will deliver those performances can be carried out. The Functional Performance Equation shows that there are two distinct efficiencies in closed circuit ball milling. One of these, ?Circuit Classification System Efficiency? (CSE), is the fraction of ?coarse? material inside the ball mill upon which grinding energy is deliberately expended, versus the remaining fraction of ?fines? or finished size material inside the mill, upon which grinding energy is wasted (on over-grinding). The role of the pump and cyclones is to maximize CSE, which is the desired grinding circuit performance. The obtainable, target CSE for any given circuit can be estimated, for example by referring to a plant data base of CSE?s. Design/optimization guidelines then allow us to specify the pump and cyclone performances that will achieve the target CSE. This paper outlines the step-by-step, systematic method of pump and cyclone selection which maximizes CSE. Numerous examples of its successful application are provided.

Jan 1, 2011

By Robert E. McIvor

"The design/optimization of the pump and cyclones to maximize grinding circuit efficiency first requires a concise understanding of, and clearly defined specifications for, desired grinding circuit performance. Subsequently, the pump and cyclone performances that provide the desired grinding circuit performance can be defined. Once the performance requirements of each process unit are determined, selection of physical equipment parameters that will deliver those performances can be carried out.The Functional Performance Equation shows that there are two distinct efficiencies in closed circuit ball milling. One of these, “Circuit Classification System Efficiency” (CSE), is the fraction of “coarse” material inside the ball mill upon which grinding energy is deliberately expended, versus the remaining fraction of “fines” or finished size material inside the mill, upon which grinding energy is wasted (on over-grinding). The role of the pump and cyclones is to maximize CSE, which is the desired grinding circuit performance. The obtainable target CSE for any given circuit can be estimated, for example, by referring to a plant data base of CSE’s. Design/optimization guidelines then allow us to specify the pump and cyclone performances that will achieve the target CSE.This paper outlines the step-by-step, systematic method of pump and cyclone selection which maximizes CSE. Numerous examples of its successful application are provided.THE FUNCTIONAL PERFORMANCE EQUATIONObservation of the feed and product size distributions going into and discharging from the mill in grinding circuits with low versus high circulating load ratios initially led to the definition of “Circuit Classification System Efficiency” (or CSE, McIvor, 1988a), and subsequently the discovery of the Functional Performance Equation (McIvor, 1988b; McIvor et al, 1992). The CSE is the fraction or percentage of “coarse” (usually in reference to the plus P80) size material inside the mill, versus “fines” or product size material finer than the circuit P80. It can be readily calculated by taking the average of the percentage of said coarse material in the mill feed and mill discharge streams. As this also represents the percentage of the mill energy expended on targeted, coarse size material, it is directly proportional to overall grinding circuit efficiency and production rate. This is all clearly expressed in the Functional Performance Equation for ball milling circuits, for which the derivation has often been presented (e.g. McIvor, 2006)."

Jan 1, 2011

By Ralph van Rijswick, Erik Vlot

"Anglo American operates 18 Weir GEHO piston diaphragm pumps (PD) in the two pump stations of the 52-km (32-mile) long Minas Rio iron ore concentrate pipeline. The pipeline is designed to transport 26.5 Mt/a (29.2 million stpy) of concentrate from the mine to the export terminal at the coast.During the commissioning of the pipeline in the fall of 2014, high pressure pulsation levels were experienced, with peak-to-peak levels as high as 20 bar. Based on pressure readings it was concluded that hydraulic resonances were present in the system, which were excited by the third and sixth harmonic of the flow pulsation generated by the pumps.Based on this observation, Weir Minerals Netherlands, manufacturer of GEHO PD slurry pumps, recommended installing a phase shift controller that controls the phase shift between the crankshafts of the individual pumps, thereby minimizing the effect of the hydraulic resonances.GEHO piston diaphragm pumps and pressure pulsation analysisPiston diaphragm pumps are used worldwide to transport abrasive and/or aggressive slurries against high discharge pressures in the mining, mineral processing and power industries. The basic operating principle of a piston diaphragm pump is shown in Fig. 1.A crankshaft is driven by an external electric motor via a gearbox. The crank mechanism transfers the rotating motion of the crankshaft into a reciprocating motion of the piston. The piston displaces a hydraulic fluid, called the propeling liquid, which displaces an elastic rubber diaphragm. When the piston moves to the right, the pressure in the pump chamber drops below the suction pressure and the nonreturn valve on the suction side will open, allowing the pumped fluid to flow into the pump chamber. When the piston moves to the left, the fluid is compressed, and when the pump chamber pressure rises above the pipeline pressure, the nonreturn valve on the discharge side will open allowing a displacement of fluid into the discharge line. The main objective of the diaphragm is to isolate the piston and the drive mechanism from the abrasive and/or aggressive fluid and create a hermetic seal between the pumped fluid and the ambient environment. Piston diaphragm pumps as shown in Fig. 1 are among the largest positive displacement pumps in the world and have been produced with stroke volumes of up to 100 L (26 gal) per pump chamber for flow rates up to 800 m3/h, discharge pressures up to 250 bar and hydraulic outputs over 2 MW per unit (van Rijswick et al., 2010)."

Jan 9, 2017

By Hans Perlid

In the handling of emulsion explosives pumping is a key operation. A number of serious accidents has shown that pumping can be a risky operation and should be carefully considered and investigated. This is the background behind a series of pump tests carried out by NITRO NOBEL.

Jan 1, 1996

[ ]

Jan 1, 1938

By T. M. Barczak, S. C. Tadolini

Pumpable roof supports provide an alternative approach to secondary support in underground mining. Unlike all other supports that are either partially or fully prefabricated prior to being transported into the mine, the pumpable support is fabricated in place in the mine entry. This reduces the underground material handling efforts and thus the injuries historically associated with in-mine support construction. On-site fabrication also facilitates application of the support in areas that are inaccessible to transportation equipment such as scoops or rail cars, making it ideal for many bleeder applications. One of the main advantages of the pumpable support is that it fully bridges from the mine floor to the roof, thereby eliminating the requirement of “topping off” the support with wooden wedges or crib blocks that soften most other support responses. This report examines the development of modern pumpable roof support technology and provides a full description of the performance capabilities of each of the support products now on the market.

By T. M. Barczak

Pumpable roof supports provide an alternative approach to secondary support in underground mining. Unlike all other supports that are either partially or fully prefabricated prior to being transported into the mine, the pumpable support is fabricated in place in the mine entry. This reduces the underground material handling efforts and thus the injuries historically associated with in-mine support construction. On-site fabrication also facilitates application of the support in areas that are inaccessible to transportation equipment such as scoops or rail cars, making it ideal for many bleeder applications. One of the main advantages of the pumpable support is that it fully bridges from the mine floor to the roof, thereby eliminating the requirement of ?topping off? the support with wooden wedges or crib blocks that soften most other support responses. This report examines the development of modern pumpable roof support technology and provides a full description of the performance capabilities of each of the support products now on the market.

Jan 1, 2008