Search Documents

By C. G. Dunn

James, Jones, and Leak (JJL) conclude that growth-rate and orientation-distribution data obtained in a steep thermal gradient should be used with caution to account for isothermally produced recrystallization textures. I agree. However, it is not clear whether they conclude a) that the orientation dependence of rate of growth of secondaries in (commercial) silicon iron depends on both temperature and a temperature gradient or b) that, in applying rate data obtained in a steep thermal gradient, the isothermal annealing temperature must be close to the temperature for which the rate data apply. Also, it is not clear what tem-

Jan 1, 1967

By R. Ebeling, M. F. Ashby

The paper is in two parts. The first develops the formulae and method needed to calculate the size, nu)nber, spacing, and volume fraction of hard or inert particles in the interior of a specimen from measurernents made on an extraction replica; throughout, the spread of- particle sizes in a single specimen is taken into account, and the extraction efficiency of the replica is considered. A method for testing whether the particles are randotnly distributed in space is described, and the spacing of randomly distributed particles is discussed. The second Part describes the application of the method to copper containing spherical particles of silica; the description includes an estimate of the errors involved, and a comparison of this with alternative methods. All parameters except uolume fraction can be determined satisfactorily, and the method offers advantages over other electron-,rzicroscopic techniques when dealing with hard particles in a softer matrix, or inert particles in a chem-ically less inert matrix. 1 HE experimental measurement of sizes and numbers of discrete particles of a second phase embedded in a matrix material from opaque, plane sections has been considered by many authors, notably by Fullman.' It is assumed that, when the specimen is sectioned, the particles are also sectioned, so that the diameters of the circles of intersection of particles with the plane of the cross section ("surface diameters") are measured. It is difficult to derive the distribution of true particle diameters ("volume diameters") from measurements of the distribution of "surface diameters" on a plane section. The measurement of size and numbers of small second-phase particles by transmission electron microscopy through thin foils of matrix containing the particles has been described by Cahn and ~uttin~' and by ~illiard.~ Because of overlap and the fact that particles which intersect the foil surface may be sectioned whereas those in the bulk of the foil are not, it is again difficult to measure the true distribution of particle sizes. The use of replicas for this sort of measurement has not been analyzed in detail. A replica made from an opaque cross section, thus replicating the circles of intersection of particles with the plane of section, is analyzed by Fullman's method and suffers from the same difficulties. Under certain circumstances, however, extraction replicas can be used, and offer a special advantage in that they make the determination of the true distribution of particle diameters particularly simple. It is the purpose of this paper to describe this extraction replica method. Consider the example of an alloy consisting of SiOz particles, whose mean diameter is about 1000A, dispersed in a copper matrix. When the alloy is sectioned and mechanically polished, the particles are not sectioned, because they are much harder than the matrix, and so will be either left in the surface or pulled out whole, and because the particle size is smaller than the abrasive size of even the finest abrasive. The particles are chemically inert in solutions which chemically etch or electropolish the matrix, so that chemical treatments do not section the particles either. (Experimental measurements of particle shape in this alloy confirm this—truncated particles are never seen.) Small, hard or inert, particles are therefore not sectioned when the specimen is sectioned and polished. An extraction replica taken from this polished surface shows the true "volume" diameter of each extracted particle; the distribution of diameters seen on the replica is the surface distribution of true "volume" diameters, and the volume distribution of true "volume" diameters is easily derived from it. The extraction replica method is not subject to the difficulties associated with sectioning of particles, and avoids the problem of overlap from which the transmission method suffers. The method is well-suited for studying hard particles in a soft matrix. Examples are provided by internally oxidized alloys, oxide-dispersion strengthened metals like T.D. Nickel, and carbides, nitrides, and strong intermetallic compounds in metals. It should be possible to adapt polishing techniques in alloys containing softer but inert particles to avoid sectioning the particles (say by electropolishing or etching). The method is tested and illustrated in Sections 8 and 9 by applying it to a dispersion of spherical SiO2 particles in a copper matrix. I) SYMBOLS Symbols are defined where they first appear in the text. Volume fractions of particles are denoted by the symbol f, particle diameters by x, center-to-center particle spacings by D, and numbers of particles by N. Mean particle diameters and standard deviations about these means are denoted by x and a. Both arithmetic (subscript A) and geometric (subscript G) means are employed. In this paper we measure the distribution of true diameters of particles which touch or pass through a random-plane section of the specimen. We may want to know the distribution of particle diameters in the

Jan 1, 1967

Jan 1, 1967

Jan 1, 1968

By M. C. Flemings, F. R. Mollard

Two-phase Pb-Sn alloys, ranging in compositiotz from 12 to 26 at. pct Pb, were unidirectionally solidified in a convection-fvee system, with thermal gradients in the liquid of up to 480°C per cm. Plane front solidification Loas achieved in all alloys at sufficiently steep gradient and slow growth rate. Conditions causing breakdown of the interface to a cellular or dendritic structure were roughly as predicted by a sinlple constitutional supercooling criterion. Structures of alloys of near-eutectic composition, solidified with plane front, exhibited a lamellar structure; the alloys furthest from the eutectic exhibited a rod-like morphology. Assumptions used in a previous paper for calculations of solute redistribution in two-phase plane front growth are shown to be reasonable for Pb-Sn alloys. Results of calculations are in good agveement with experiment. These show that variations in growth rate during solidification of the composite produce marked changes in average composition of the solid. IN a previous paper, Part I,' conditions necessary for plane front solidification of two-phase alloys were discussed and calculations given on solute redistribution in this type of solidification. This paper, Part 11, describes experiments on Pb-Sn alloys, designed to check the assumptions of the analyses presented, and to demonstrate their applicability to a given alloy system (Pb-Sn). APPARATUS AND PROCEDURE General. A vertical crystal growing unit was built for the study as described below, and "normal solidification" employed throughout (i.e., the ingot was completely melted except for a portion near the bottom end and then solidification initiated). The furnace was designed to permit achieving very low interface velocities, and steep gradients, in essential absence of convection; it is sketched in Figs. 1 and 2. Simple heat flow considerations indicated choice of a small-diameter specimen (ingot) to achieve high thermal gradients; ingot size chosen was 0.3 cm in diam. The ingots were held inside silica tubes 0.06 cm wall thickness. The requirement for an essentially convection-free system was met by use of the vertical furnace with the heat source over the heat sink, as well as by use of the small diameter ingots. In addition, by selection of tin-rich Pb-Sn alloys, the diffusion boundary layer (lead-rich) was denser than the bulk liquid and would not cause convection. The only apparent driving force for convection in this system was the small transverse temperature gradient resulting from heat flow into the samples from the furnace. Such convection must have been small, however, since 1) no temperature fluctuations in the melt were noted in the recordings, which would have indicated turbulent convection, and 2) experimental results obtained and described below could not have been achieved in presence of significant convection. Ingot Preparation. Pb-Sn alloys ranging from 12 to 26 at. pct Pb were prepared from high-purity lead and tin (99.9999 pct pure metal). Each alloy was prepared by first melting the pure metals in the proper ratio in air, in a Pyrex container. The melt was then stirred thoroughly with a graphite rod and cast into a preheated graphite mold. Ingots were then prepared from these castings for use in the actual experiments; each ingot consisted of a rod of alloy, 15 cm long in a 25-cm-long transparent fused-silica tube, 0.3 cm ID and 0.06 cm wall thickness. One chromel-alumel thermocouple, made with 0.004-in.-diam wire and protected by a two-hole alumina tube, was inserted into each ingot. The 1.5 cm of the thermocouple nearest the bead were protruding from the alumina tube and were coated with a very thin layer of boron nitride paste which provided electrical insulation while allowing good heat conduction. The electrically welded junction size was about that of each wire and the cross section of the two wires represented about 0.3 pct of the sample cross section. Including the coating, the thermocouple cross section still represented less than 0.5 pct of the ingot cross

Jan 1, 1968

By H. E. Cline

Solidification of Pb-Sn alloys ranging in composition from 1.2 to 56 at. pct Pb ws observed with polarized light. Lamellar structures were observed over a larger range of compositions in alloys containing excess tin than excess lead, as expected from constitutional supercooling. The occurrence of pools of supercooled liquid surrounded by lead is explained by the difficulty in nucleating tin. Cells and dendrites weve observed in tin-rich alloys. Evidence was found that the degenerate structure formed at low growth rates, the formation of faults, and abrupt changes in composition and structure can be attributed to non-steady-state growth. The apparent interface shape was observed to have deep grooves at the interphase boundaries. HUNT and Jackson have observed the shape of the interface during growth of organic eutectics. They observed the formation of lamellar faults and shape instabilities upon changes in growth rate. The lamellar structure in these organic eutectics was not restricted to the eutectic composition. Recent work by Mollard and Flemings2 indicated that Pb-Sn alloys from 12 to 26 at. pct Pb could be solidified with a lamellar or rodlike structure if a sufficiently steep temperature gradient was used at a slow growth rate. Observations of the solid liquid interface of the Pb-Sn eutectic were made by Davies3 using polarized light. Photographs were at too low a magnification to determine the interface shape, but he has concluded that tin was the leading phase. In the following experiments, solidification of a range of Pb-Sn alloys from 1.2 to 56 at. pct Pb was observed using polarized light, to determine the factors controlling stability of the lamellar structure. EXPERIMENTAL Procedure. One hundred-gram ingots of alloys prepared from 99.999 pct pure Pb and Sn were cast into graphite molds under argon. The compositions of the alloys were 1.2, 6, 12, 26, 36, 46, and 56 at. pct Pb. Two-gram pieces were melted between two cover glass slides which were squeezed into a 1-mm separation. Samples were then observed under polarized light in a hot stage shown in Fig. 1. A long working distance objective designed for viewing at 500 times was used. Photography was made difficult by the lack of illumination and contrast at these high magnifications. By using an elliptical polarization compensator, as suggested by A. Holik, the contrast and illumination could be optimized. Photographs could be taken only at slow growth rates to avoid excessive interface motion during the 15-sec exposure used. The solidification rate was varied by increasing or decreasing the power to the heater. It was found that insulation was necessary to avoid undesired growth rate fluctuations. The temperature gradient, as measured with two thermocouples 1 cm apart, was 80" ± 20°C per cm during all the experiments reported here. The advantage of this procedure is in being able to observe solidification while it is occurring. However, the observations are restricted to the glass-metal surface and may be influenced by this surface. Also, one has no knowledge of the interior of the sample, in contrast to studies of the freezing of transparent organic eutectics.' Observations. The alloy near the eutectic composition (26 at. pct Pb) solidified in a lamellar structure when the growth rate was uniform. If the growth

Jan 1, 1968

By C. Altstetter, Y. Huang, E. de Lamotte

Nitrogen was introduced into pure niobium (colutn-bium) and dilute Nb- Zr alloy wires by equilibration with pure nitrogen gas at high temperatures. Room-temperature hardness was correlated with the alloy composition, heat treatment, and microstructure. Hardness was found to be most sensitive to the amount of nitrogen in solution; however, a significant hardening up to 500 Dph look place upon aging of quenched alloys. A coarse dispersion of nitride did not significantly increase the hardness of the material though the nitride was found to have a hardness of 1400 Khn. BY now the marked effect of nitrogen on the properties of bcc refractorv metals is we ll-documented. There are few studies, however, in which the state of the solute has been carefully controlled. Indeed, the composition-temperature-pressure relationships in nitrogen-refractory metal systems have been determined precisely for only niobium and tantalum.'-4 Most investigations on niobium have dealt with alloys High-nitrogen alloys cleaved on (100) planes and had negligible ductility. Precipitation was found to occur in either a discontinuous or a continuous fashion, depending on the composition and cooling rates. Upon cooling, the precipitation first proceeded discontinu-ously by the nucleation of nilride needles at subbound-aries and subsequent growth of a two-phase microcon-stituent. At lower temperatures continuous precipitation occurred in the subgrain interior ahead of the discontinuous precipitation interface. containing nitrogen, carbon, and oxygen in significant but uncontrolled and, in several instances, undetermined amounts. Thus, there has been some uncertainty regarding the presence and the distribution of precipitates. This paper presents results which relate the hardness and microstructure to the heat treatment and nitrogen content of niobium and Nb-Zr alloys. Niobium rod* produced by the Wah Chang Corp.

Jan 1, 1968

By P. R. Sahm, T. V. Pruss

Mixtures of fine GaSb and Gds as well as preal-loyed GaSbl,As, powders were hot-pressed at 690°C and 25,000 psi. Dense alloys with compositional gradients of less than 5 pct were obtained from mixtures containing about 20 mol pct GaAs. For x < 0.2, there were increasing compositional gradients, and for x > 0.2 a GaAs-rich second phase appeared in the microstructure. Densification as well as alloying wlechanisms were enhanced by dissociation and, possibly, oxidation reactions of the powders. Densification of coarse prealloyed material, however, primarily depended on plastic flow phenomena and required temperatures just below solidus and pressures of 50,000 psi Thermal and electrical properties were measured. Although in no case was the figure of merit of melt growth materials approached closer than to within 25 pct, the better overall thermoelectric properties were found in coarse-grained, prealloyed materzals which had been compacted to near theoretical density and where grain regrowth had been induced. Similar results are believed to hold in other binary 111-V compound systems if processed under similar conditions. The densification of unalloyed GaSb powders during pressure sintering (= hot pressing) was shown to depend strongly on powder particle size.&apos; Fine powders displayed a "liquid skin effect" that enhanced compaction through the presence of liquid gallium, whereas coarse powders compacted predominantly by plastic flow. The liquid skin effect, in particular, appeared attractive for alloying GaSb with other, higher-melting, III-V compounds, and to densify these in a one-step operation. This is of special interest in the case of III-V compound alloys as the conventional techniques of melt growth or long-time annealing of powders2 is very time-consuming, especially in cases where a large separation of liquidus and solidus can be expected, such as in GaSbl alloys.2 It was felt that experimentation with this system, a particularly unfavorable example, would allow us to extrapolate to several other, more favorable, cases. Uses of Ill-V alloys are most evident in thermoelectric energy conversion devices.&apos; For this reason certain thermal and electrical properties were measured and compared to those of melt-grown material and to hot-pressed prealloyed powders. EXPERIMENTAL PROCEDURE The pressure-sintering apparatus has been previously described.&apos; Using this equipment, both powder mixtures of GaSb with GaAs and prealloyed GaSbl-,As, powders were hot-pressed. The mixtures were pre- pared from cast GaSb and melt-grown GaAs. The prealloyed material was obtained from stoichiometric melts, initially heated to 1200°C in an evacuated quartz ampoule, and then annealed in the solidus-liquidus interval. A typical annealing cycle consisted of a heating to 850°C (1 hr), extended successive annealing at 750°C (65 hr), and slow stepwise cooling (25 hr) to below solidus. The GaSb, GaAs, and GaSbl-,As, materials were ground in a vibrational mill to particle sizes below 500 . A jet mill reduced these further where necessary. Fine powders were analyzed by Coulter counting for their size distribution. Average sizes by volume were calculated from the data. Mixing of the powders, where necessary, was carried out through rapid vibrational motion. The hot-pressing operation consisted of a degassing period of 15 hr, in most cases at 690°C, followed by several hours of compression, normally 25,000 psi at 690°C for powder mixtures and 50,000 psi at 710°C for prealloyed powders. The chemical compositions were confirmed by X-ray fluorescence analysis. To estimate the degree of solid solution achieved, lattice parameters were determined and interpreted according to Vegard&apos;s rule. In addition, optical microscopy helped to correlate the relative amounts of the phases present as well as the degree of porosity to the measured density. To reveal grain boundaries, polished surfaces were etched4 with H 2 O:H 2 O:HCl = 2:l:l. In several cases microscopic concentration gradients were monitored by electron-probe analysis-. RESULTS AND DISCUSSION Alloying and Densification of GaSn-GaAs Powder Mixtures. After preliminary experiments showed that no appreciable alloying took place in mixtures of coarse GaSb (22.5 p) and fine GaAs (2.5 p) powders, hot pressing of mixtures was confined to fine powders only (3.1 and 2.4 p, respectively). Alloying and densification apparently occurred simultaneously with a grain regrowth mechanism which depended on the presence of a liquid phase.&apos; The liquid phase was provided by the dissociation of GasbS particles into liquid gallium and antimony above 555°C. This not only enhanced grain regrowth and densification, as in unalloyed GaSb,&apos; but took on additional importance here for the alloying process. Alloying was speeded up by the resulting liquid-solid interaction as compared to the very slow solid-state diffusion process normally expected at these temperatures.&apos; The results obtained with a series of powder mixtures have been compiled in Table I. It is seen that for mixtures with less than 20 mol pct GaAs, x < 0.2, the compositional ranges increased and for x > 0.2 a GaAs-rich phase and free antimony appeared in the microstructure in sizable amounts.

Jan 1, 1968

By A. J. Ardell, O. D. Sherby

The elevated-temperature steady-state creep behavior of polycrystalline a Zr was studied in vacuo under constant tensile stress. The experiments were conducted from 660° to 845°C over the stress range 870 to 5400 psi. The steady-state creep rate, is, of a Zr was found to be related to the applied stress, a, and temperature, T, by the equation where C is a constant. Two interpretations of the data are considered, each requiring different values of the parameters ß, Q, and . It is shown that this formula can be derived using Gilman&apos;s phenomeno logical equation relating dislocation velocity to the shear stress for the case where dislocation mobility is limited by the nucleation of kink motion. From the fundamental dependence of strain rate on dislocation velocity and the density of mobile dislocations, the factor exp(ßo) can be related to the stress dependence of the dislocation density, and Q to the energy of kink formation. The two interpretations considered are as follows: Case I—the parameters are adjusted so that the equation above describes the data over the entire range of stress and temperature, implying that creep is controlled exclusively by dislocation glide; Case IIthe parameters are adjusted to allow for the possibility that creep is diffusion-controlled at high stresses but glide-controlled at low stresses. For both cases the values of the parameters are within the spread permitted by the data. Factors favorable to the observation of the unusual stress -dependence of i, for a Zr are discussed and it is shown that the anomalously rapid rates of self-diffusion and the low modulus on the principal glide system are primarily responsible for the anomalous creep behavior. Metal-lograflhic observations are presented and discussed with reference to the overall creep behavior. PREVIOUS investigations of the creep behavior of a Zr have been conducted from room temperature to about 500C The results of these investigations are primarily of engineering significance because of the variety of conditions under which they were carried out, and the low testing temperatures employed. Little information is available concerning the fundamental nature of the elevated-temperature creep behavior of a Zr. This investigation of the creep behavior of a Zr above half the melting temperature (the melting temperature, T,, of a Zr is estimated to be about 1860"K was initiated because there are two significant anomalies of the physical properties of a Zr: a) the rate of self-diffusion in polycrystalline a Zr is anomalously rapid: b) both Young&apos;s modulus for polycrystalline a Zr and the shear modylus as-sociated with the prismatic slip system { 1010)( 1120) (the principal slip system in a Zr 7) have anomalously large temperature variations The importance of these quantities to the understanding of creep behavior has been demonstrated, and it was hoped that this investigation would provide a critical test of the predictions based upon the analysis of creep data for other pure metals. However, as the investigation progressed it became increasingly clear that the unusual creep behavior of a Zr could not be analyzed in a conventional manner. 1) EXPERIMENTAL EQUIPMENT AND PROCEDURES Two grades of zirconium, designated A and B, were used in this investigation. The analyses, as supplied by the vendors, are presented in Table I. Material A, with a nominal purity of 99.84 pct, was supplied by the Wah Chang Corp. in the form of cold-rolled sheet from which specimens were machined without further fabrication. Material B, with a nominal purity of 99.95 pct, was purchased from the Nuclear Materials and Equipment Corp. in the form of iodide crystal bar.

Jan 1, 1968

By R. E. Hummel, J. W. Koger

IT is generally accepted that the martensitic start temperature (Ms) can be determined by resistivity measurements and is that temperature where the resistivity vs temperature curve on cooling first deviates from a straight line.1-4 Both Titchener and ever&apos; and pops5 have used resistivity measurements to follow the martensitic transformation in b1 Cu-Zn and ternary Cu-Zn-based b-phase alloys, respectively. Actually because of the nature of their measurements the temperature of minimum resistivity (M) was used by these authors to determine "Ms" . Also, due to experimental difficulties in detecting M, with resistivity measurements, Pops and Massalski 8 determined M, by optical microscopy. The present communication is concerned with high-precision, low-temperature resistivity measurements which reveal a definite M, temperature which differs from the temperature of minimum resistivity (M). It is also shown that M is merely the result of the geometry of the percent-transformation curve and the temperature coefficient of resistivity of the alloy. In other words, it will be demonstrated that M has no apparent significance (except that it denotes a temperature at which some percent of martensite can be detected in a given alloy). Alloy specimens were made by melting 99.999 pct Cu and 99.9999 pct Zn in sealed and evacuated quartz tubes and homogenizing them at 601PC for 300 hr. After the alloy was cold-rolled into foils suitable for resistivity measurements, it was quenched in ice water from 871PC. The chemical analysis showed a zinc content of 38.8 wt pct. The cooling rate during the martensite transformation was 1°C per min and was controlled with a thermistor. Electrical resistivity measurements were made using a K-3 type potentiometer; the reproducibility of the resistivity values was better than 0.03 pct. Temperatures were measured with a thermocouple to an accuracy of better than 0.2° C. Fig. 1 shows the resistivity vs temperature curves of the martensitic transformation in B1 Cu-Zn for both cooling and heating. The starting point of the martensitic transformation (M,) was taken as that

Jan 1, 1968

By G. Das, S. V. Radcliffe

The substructural features developed in tungsten as a function of annealing temperature (up to 2200°C) and type of material [undoped and doped powder metallurgy (PM) tungsten and electron beam melted tungsten] have been investigated by transmission electron microscopy. For doped PM tungsten wires, characteristic "par-ticulate" substructural features developed rapidly with increase in annealing temperature above 700°C. The features consisted of parallel rows of elongated or circular shapes (500 to 1000A diam) lying along the direction of the wire axis and were identified as internal voids by diffraction contrast experiments. In recrystallized doped PM rod, larger voids were observed and were identified by precision dark field analysis to be cubic in shape and bounded by (100) planes. In marked contrast with both the doped PM materials, recrystallized undoped PM rod exhibited only very occasional and randomly arranged voids. Furthermore, no voids were observed in either material after electron beam melting. The high concentration of voids in the doped PM materials is attributed primarily to vaporization of doping additions or their pvoducts situated at the original grain boundaries , whereas the few voids in undoped material are considered to be traces of microporosity which were not eliminated during sintering. A tentative mechanism is suggested for the dezlelopment of the voids in relation to the processing sequences (sintering and working) and to the subsequent annealing. In recent years, a characteristic substructural feature consisting of rows of small elongated or circular regions of light contrast lying along the direction of working has been seen in thin foil electron microscopy studies of annealed sheet, wire, and rod tungsten. These features were present in the published micrographs of sheet by Weissmann et al.1 and of wire by Meieran and Thomas2, although the authors did not draw attention to them. Wronski and Fourdeux3 observed similar features in sintered rod tungsten (it was not specified whether or not the material was doped*) and interpreted them on the basis of their ap- particles, based on extraction replica evidence from the fracture surface of the initial hot-rolled slab material from which the sheet was prepared. No diffraction contrast experiments on the features were reported in any of these studies. The present investigation was undertaken with the primary objectives of: a) identifying the nature of these substructural features in tungsten by electron diffraction contrast experiments, since the contrast for voids can be expected to differ from that for crystalline or glassy particles, and b) elucidating the origin of the features and their development. For the latter purpose, doped and undoped powder metallurgy tungsten was obtained as rod and wire to represent different stages of reduction during final processing. These materials were examined both in the as-processed condition and after annealing to successively higher temperatures. In addition, the same doped and undoped materials were examined after vacuum melting in rod form. I) MATERIALS AND PROCEDURE Doped powder metallurgy (PM) tungsten wire (commercial purity 99.9 pct W) was obtained in the as-drawn and surface ground condition (0.030 in. diam "ground seal rod"). Doped and undoped tungsten rod (0.075 in. diam) representing an earlier stage of final processing was obtained from the same commercial source (Refractory Metals Division, General Electric Co.). Lengths of both the doped and undoped rod materials were single-pass melted in an electron-beam zone refiner to examine the effect of vacuum melting on the substructure. Annealing was carried out in a tungsten crucible in a tantalum strip resistance furnace under a vacuum of l0-15 mm Hg. Longitudinal sections of the wire and rod materials were examined by light and electron microscopy. The preparation of thin foils suitable for electron transmission from 0.030 in. diam tungsten wire and the rod specimens was carried out by means of a high-precision microjet technique developed to provide lack of jet stability and precise control of the area thinned. The method is described in detail elsewhere.&apos; The foils were examined in a JEM 6A electron microscope using a goniometer stage (±20 deg tilt, 360 deg rotation) and operated at 100 kV. To minimize contamination problems a 200 µ condenser aperture was used in conjunction with a useful beam current of 50 µA. II) RESULTS AND DISCUSSION A) Diffraction Contrast Analysis. In order to determine the optimum conditions for the development of the substructural feature, a series of isochronal 30 min annealing experiments were carried out on specimens of the doped PM tungsten wire. The transmission electron microscopy analysis showed that the as-drawn wire, Fig. 1(a), consists of &apos;fibers&apos; whose long axis is closely parallel to the wire axis of (110). The fiber width averages some 0.5 µ. Dense disloca-

Jan 1, 1969

By G. Birkbeck, T. C. Wells

Pearlite morphology in three commercially produced, low-carbon steels has been studied using optical and electron microscopy. A reduction in the cooling rate from 600° to 6°C per hr increased the interlamellar spacing but had little effect on pearlite content. The form of the lamellae was also assessed in terms of a new parameter, the ratio of lamellae length to interhmellar spacing. The variation of this parameter with cooling rate depended on steel composition. For each steel, it would appear that an optimum cooling rate exists at which lamellar pearlite can be produced to the greatest extent, though not necessarily the same extent in different steels. PeARLITE morphology depends principally on steel composition, prior austenite grain size, and either cooling rate or isothermal transformation temperature. Alloying with manganese,&apos;" fine grain size,374 and slow cooling rates reduce the likelihood that a well-developed lamellar structure will be produced. Instead, imperfect structures usually consisting of partly globular carbides are formed in a ferrite matrix. Such structures have been described as granular.1,2,5 degenerate,6 or semi4-pearlite. Manganese additions also progressively lower the eutectoid temperature and the carbon concentration at the eutectoid so so that, for a given carbon content. the pearlite fraction is increased as manganese is added. While the effects of manganese are understood in a general way, quantitative studies of pearlite morphology have been carried out mainly on steels of eutectoid composition;9 little quantitative data is available for low-carbon steels. Certain anomalies exist in the behavior of steels containing -1.5 pct Mn, however. The pearlite morphology in niobium-treated steel differs from that which is generally accepted as typical of low-carbon/manganese steels in that a reasonably well developed lamellar structure is sometimes observed. In the present work, the effects of changes in cooling rate from 600° to 6°C per hr on the pearlite morphology in three commercially produced, low-carbon steels have been studied by both optical and electron microscopy. I) MATERIALS The steels were of the following types: 1) 0.1 pct C, 0.4 pct Mn steel (En 2, a composition similar to specification SAE 1010); 2) niobium-treated, 0.2 pct C, 1 1/2 pct Mn steel (BS 968:1962); 3) silicon-killed 0.2 pct C, 1 1/2 pct Mn steel (En 144, a composition similar to SAE 1320). The chemical analysis for each steel is given in Table I. To facilitate the comparison of pearlite morphology in the three steels, steels 1 and 3 (which were obtained as 1/2-in. plate and 1-in.-diam bar, respectively) were hot-rolled in the laboratory to $ in. thickness, finishing at around 850°C. The BS 968:1962 was received as 1/8-in. plate finished at 885°C and was not further worked. Specimens from each steel were heat-treated in vacuo at 950°C for 1 hr and cooled at rates of 600°, 60°, and 6°C per hr. 11) EXPERIMENTAL Pearlite contents were determined by point counting (500 points) on longitudinal sections mechanically polished and etched in 2 pct nital. Pearlite morphology is usually considered in terms of interlamellar spacing. For pearlite colonies randomly distributed in space and having a true, constant interlamellar spacing So Pellissier et al.9 determined the distribution curve for the apparent spacings of the lamellae on a random section plane. The areal fraction fs of the pearlite colonies occupied by apparent spacings up to a limiting value S is given by:

Jan 1, 1969

By F. Weinberg

Lead single crystals have been deformed in tension over the temperature range of 4.2°K to the melting point. Changes in flow stress resulting from temperature cycling and strain rate cycling have been measured as a function of temperature for crystals of different orientations and purity. It was found that the flow stress ratio, after correcting for the temperature dependence of the shear modulus, decreased progressively with temperature above approximately 0.5Tm. The activation energy calculated from the high-temperature portion of the curve was found to be markedly higher than that of self-diffusion. For single glide crystals, the corrected flow stress showed an increase above 0.5 Tm before decreasitzg with temperature. This increase is attributed to static recovery occurrittg during temperature cycling. THE temperature dependence of the flow stress, based on temperature cycling and strain rate cycling, has been extensively investigated,&apos; and on the basis of these results dislocation models of the work-hardening process have been proposed. In general, the flow stress is divided into two parts, ts, the short-range interaction term, which is only effective at low temperatures and which decreases with increasing temperature, and TG, the long-range stress term, which is independent of temperature after allowing for the temperature dependence of the shear modulus. The observations demonstrating that tG/µ is independent of temperature were generally carried out at low temperatures to minimize recovery effects. Several investigations have been reported on flow stress measurements at high temperatures2"5 which demonstrate that TG/µ does not remain constant at temperatures above 0.5Tm (where Tm is the melting temperature of the material in OK). Specifically, Hirsch and warrington3 carried out temperature cycling tests at two strain rates on single and polycrystalline aluminum up to 0.8 Tm and on polycrystalline copper. For aluminum they found that the flow stress ratio (the flow stress at temperature T2, divided by the flow stress at the reference temperature T1 in one temperature cycle) dropped progressively with increasing temperature above 0.5Tm. From the slopes of the high-temperature portions of the curves, they determined an activation energy for the deformation process of 1.6 ev (at best) which they considered was in agreement with the activation energy of self-diffusion, 1.35 ev. Calculations of the activation volume demonstrated that the deformation was not controlled by dislocation climb. They proposed a mechanism in which the rate-controlling process at high temperatures was due to the rate of move- ment of vacancies away from jogs, i.e., that of self-diffusion. Results of Lucke and Buhler4 on single crystals of aluminum confirmed this conclusion. They measured the critical resolved shear stress of aluminum over a wide range of temperature and strain rates. They found that the temperature dependence of the critical resolved shear stress was similar to that of the flow stress ratio, as determined by Hirsch and Warrington, and from their data calculated an activation energy for high-temperature deformation of 1.35 ev identical to that of self-diffusion. More recently Gallagher5 has carried out a detailed investigation of the temperature dependence of the flow stress ratio of copper, silver, and gold. In all cases, he found that the flow stress ratio, after adjusting for the shear modulus temperature change, drops at high temperatures. The activation energies he determined were found to be appreciably higher than the activation energy of self-diffusion of the material being considered. The flow stress ratio was found to be dependent on the orientation of the material, and, in addition, an anomalous increase in the flow stress ratio for copper, oriented for single glide, was observed above 0.5Tm. The purpose of the present investigation was to measure the critical resolved shear stress, the flow stress ratio, and the strain rate sensitivity of lead, primarily as a function of temperature. The results should indicate whether, following Lucke and Buhler, the critical resolved shear stress of lead has the same temperature dependence as the flow stress, and, following Hirsch and Warrington, whether the activation energy for high-temperature deformation in lead is the same as that of self-diffusion. Lead deforms as a normal fee material,6&apos;7 is available in high-purity form, can readily be grown as single crystals, and, for this investigation, has the very considerable advantage of having a low melting point, 327°C. The observations of the critical resolved shear stress of lead have been published elsewhere.&apos; EXPERIMENTAL PROCEDURE The experimental procedure was essentially the same as that used in the critical resolved shear stress measurements.&apos; Single crystals of 99.999 pct (59) and 99.9999 pct (69) lead were deformed in tension with a table-model Instron in a silicone oil bath above room temperatures and in a cooled methyl alcohol or liquid-nitrogen bath below room temperatures. The test specimens were rectangular in section, 0.65 by 0.33 cm, and had a 5-cm gage length. The specimens were grown as single crystals with tapered ends, which fitted into matched tapered grips for testing. To obtain the flow stress between two temperatures, specimens were first deformed approximately 1.0 pct at the higher temperature. The test was then stopped, the load relaxed, the oil bath removed without disturbing the specimen, the grips and specimen cooled with a fan and then immersed in liquid nitro-

Jan 1, 1969

By J. Brett, S. Friedman

A study of the diffusion of nickel into both fibrous and recrystallized 0.065-in.-diam silica-alumina doped tungsten wire at 1200°C has been conducted. The diffusion profiles were determined by chemical dissolulion of successive circumferential layers and spectro-photometric determination of nickel in the etchant. It was shown that the diffusion of nickel into tungsten is markedly structure-sensitive. No significant amount of nickel could be introduced at 1200°C into tungsten which had first been recrystallized at temperatures of 2300°C, leading to an upper limit estimate for the bulk diffusivity of nickel in tungsten of 10-11 sq cm per sec at 1200°C. However, nickel did diffuse into initially fibrous wires, caused re crystallization, and was alsays present at the advancing recrystallization front. The accumulation of nickel in an initially fibrous region ceases when the recrystallization front arrives. The characteristics of the resulting diffusion profiles are explained in terms of the relation between diffusion processes and micro structural changes. WHILE it is well-known that the presence of nickel and certain other metals causes low-temperature recrystallization of the cold-worked fibrous structure of doped tungsten,&apos;&apos;&apos; the character of the phenomenon is not well understood. Recently it was shown that the recrystallization reaction can be induced at low temperatures by the presence of solid nickel on the surface of doped wire, but not by exposure to nickel vapors.3 Once recrystallization was initiated, a continued source of nickel was required for propagation of the recrystallization front. The phenomenon appeared to be a complicated solid-state reaction since, in addition to the change in structure of the tungsten from fibrous to equiaxed grains, diffusion of nickel from the surface into the recrystallized and fibrous structures was occurring with possible chemical reaction between nickel and tungsten at the surface and interaction of nickel with the dopants which ordinarily stabilize the fibrous structure within the wire. The objective of the present work was to study the diffusion of nickel into fibrous and recrystallized tungsten structures in order to clarify the relationship of the diffusion process to nickel-induced recrystallization. Studies of interdiffusion in the Ni-W system4"7 have been principally concerned with the mobility of tungsten in nickel. Information on diffusion of nickel in tungsten is meager, and there seem to be no studies of the mobility of nickel in tungsten which elucidate the structural aspects of the phenomenon. The present experiments were designed to determine the diffusivity of nickel at 1200°C in fibrous tungsten, in large-grained tungsten prerecrystallized at high tem- perature, and in tungsten recrystallized at 1200°C due to the presence of nickel. Although the concentration profiles were determined in these experiments, unexpected changes in boundary conditions or complex diffusion paths complicated the analysis of these profiles so that the interpretation could not be readily expressed in terms of simple diffusivities. EXPERIMENTAL PROCEDURE The experiments were conducted on Sylvania 0.065-in.-diam silica-alumina doped commercial tungsten wire, hereafter designated as ordinary doped wire. A special lot of 0.065-in.-diam silica-alumina doped low-nickel wire was also used. Impurity analyses of the wire are given in Table I. The experimental design is shown in Fig. 1. All heat treatments were conducted in vacuum. Two groups of ordinary doped wire were prepared for diffusion with nickel. One group in the as-received (fibrous) condition was elec-tropolished, nickel-plated, and annealed at 1200°C for 20 and 40 hr, or was exposed to nickel vapor at 1200°C for 20 and 40 hr. The second group was recrystallized to an equiaxed grain structure at 2300°C for 3 hr, electropolished, nickel-plated, or exposed to nickel vapor for anneals at 1200°C for 20 and 40 hr.

Jan 1, 1969

By Robert J. De Angelis, James H. Barker

An improved method for solving dynawzical dislocation problems using a digital computer is described in this paper. Interactions between two distinct types of dislocations were studied: attractive screw dislocations; and Lomer lock forming dislocations. One dislocation is positioned in the lattice and is initially at rest, while the other dislocation is moved through the lattice on an intersecting slip plane at a constant velocity in the range 0.5 to 0.999C. (C is the transverse velocity of sound.) The results obtained from these computations indicate that screw dislocations account for a small fraction of the total strain over a wide portion of the range of velocities studied. They further indicate that mixed dislocations mainly repel other dislocations in the neighborhood of the active glide plane. From this a possible explanation for cell formation is put forth. The density of Lomer locks expected to exist after a strain of 0.2 was found to be 1.4 x 106 cm-2 which is in good agreement with indirect experimental estimates. IN the past, predictions of favorable or nonfavorable dislocation reactions were based on the associated changes in elastic strain energy. Such considerations take no account of the probability of the two dislocations coming into contact to react. Venables1 was the first to approach these probabilities by considering the interactions between two moving screw dislocations on perpendicular glide planes. Because of the restrictive types of dislocations and glide plane geometry employed, his results have limited application to metallic crystals. The work to be presented here develops a general approach to solving dynamical dislocation problems; either dislocation-dislocation interactions, presented here in detail, or dislocation interactions with any other suitably defined stress field. Two types of dislocation-dislocation interactions common to face centered cubic (fee) materials are considered: those between pure screw dislocations of opposite sign on intersecting slip planes and those between mixed dislocations on intersecting slip planes, that can react to form a perfect dislocation. This latter reaction, referred to as the Lomer reaction, produces a locked product dislocation that finds it energitical favorable to disassociate into two Shockley partials and a stair-rod dislocation. This partial configuration known as a Lomer-Cottrell (L-C) lock plays a major role in work hardening of fee crystals. seeger2 names the L-C lock as the prime contributor to Stage II hardening while Kuhlmann-wilsdorf3 and Meakin and Wils- dorf4 also state that it is a significant contributor to work hardening. However, with a few notable exceptions,5-7 direct observations of the Lomer lock and the L-C lock by electron transmission microscopy are scanty, and even these are subject to other interpretations.5,6 In a study of partial dislocations present in austenitic stainless steel, whelan8 did not observe any L-C locks at the head of pile-up groups. This result contradicted existing work hardening theories and led him to postulate an alternate theory based on the stress required to break away dislocations intersecting a pile-up group, from their stacking fault nodes. Due to the importance of the Lomer reaction in producing L-C locks which are an essential feature in current work hardening theories and because there exist no data giving direct quantitative values for the density of locks, and because there has even been some doubt expressed as to whether this important reaction occurs at all, a study of the dynamic behavior of the mixed dislocations which form the Lomer lock was undertaken. Due to their ability to cross-slip with relative ease, screw dislocations play an important role in the deformation of fee crystals. For this reason, the second type of reaction considered here is between screw dislocations of opposite sign. In addition, computations in volving screw dislocation interactions are relatively simple, thus providing a convenient check on the cornputational scheme employed. DEFINITION OF PROBLEM The force exerted on a dislocation due to a generalized stress field is given by the Peach and Koehler9 equation: Here t2 and b2 are respectively the tangent and Burgers vectors of the dislocation, and T1 is the stress dyadic defining the local stress field. The stress field may be externally applied or generated internally by the presence of a lattice defect, such as a second dislocation, as is the case in this work. Frank10 has shown that an equivalent momentum, P, of a screw dislocation can be defined by: Here, EST is the total energy of a screw dislocation and ESo is its rest energy. The left side of Eq. [2] is the time derivative of momentum and the right side is the position derivative of the energy due to the dynamical nature of the dislocation. The total energy of a dislocation is the sum of the potential and kinetic energies. Weertman11 has developed the expressions which were used here; these give the potential and kinetic energies of uniformly moving edge and screw dislocations in an isotropic medium.

Jan 1, 1969

By S. F. Frederick, G. F. Pittinato

The deformation mechanisms operating in Ti-5Al-2.5Sn at 20°K under uniaxial and biaxial stress fields were determined by using both optical and electron microscopy. In the uniaxially stressed specimens, de-fu~rnation twins were found only in the immediate vicinity of the fracture. Twinning was, however, established as a deformation mechanism under biaxial stress conditions. The same slip systems were opera-tiz,e under both uniaxial and biaxial stress. Prismatic slip was identified as the major slip syslem; however, basal and first-order pyramidal slip also occurred, but to a lesser degree. The interaction of moving dis-locations on intersecting slip planes resulted in the formation of jogs and dipoles. Hexagonal dislocation networks were formed only under biaxial stress conditions. A discussion is given on the formation of hexagonal dislocation networks. IT has been shown that titanium alloys can exhibit unusually high strengths when tested in a biaxial stress field.&apos;-" The high biaxial strengths are a consequence of a strong basal plane sheet texture which results in distinctly anisotropic flow properties. This texture strengthening appears to decrease with decreasing temperature2 and would seem to indicate a change in deformation modes. For example, in a uniaxial tensile test, Ti-5A1-2.5Sn yields isotropically at 20°K but is strongly anisotropic at room temperature. The increase in biaxial ultimate over uniaxial strength at 20°K is also much less than at room temperature. It is known that titanium car] form deformation twins more readily at cryogenic temperatures than at room temperature.4 Since the formation of deformation twins will reduce the degree of basal texture in sheet material,&apos; an accompanying decrease in texture strengthening would be expected. To investigate more fully the nature of texture strengthening at cryogenic temperatures, the deformation modes of Ti-5A1-2.5Sn tested in uniaxial and 1:1 biaxial tension at 20°K were studied by optical and electron transmission microscopy. EXPERIMENTAL PROCEDURE The uniaxial and biaxial stress test specimens were prepared from 0.020-in. thick sheets of Ti-5A1-2.5Sn ELI having the composition shown in Table I. Uniaxial stress conditions were obtained by using flat tensile specimens machined from the sheet material. The longitudinal axis of the tensile specimens was aligned perpendicular to the rolling direction of the sheet. Tile biaxial test specimens were prepared by rolling precut, 19-in.-lengths of sheet into 4-in.-diam cyl- inders. Following longitudinal butt welding, the cylinders were stress relieved at 1000°F for 4 hr. A 9-in. sq "window" was then chemically milled into each cylinder&apos;s surface reducing the wall thickness in the milled area to approximately 0.006 in. The testing procedure consisted of pressurizing the cylinders while simultaneously applying a tensile load. Using this technique, a 1:l axial to hoop stress was obtained. Complete details of the specimen and testing procedures are given in Refs. 1 and 2. The biaxial and uniaxial stress specimens were all tested in liquid hydrogen. Specimens for electron transmission microscopy were prepared by first chemically milling to a thickness of about 0.001 in. followed by electrolytic polishing to electron transmission thickness. The chemical milling solution, consisting of 800 ml of water,

Jan 1, 1970

By A. Moskowitz, L. S. Redmerski

The corrosion resistance of stainless steels can be strongly affected by surface treatments. Changes in corrosion resistance can relate to surface composition, integrity and stability of the passive film, and to surface profile (roughness). Operations producing oxidation at the surface, such as annealing, heat treating, and welding, can result in a chromium-rich scale and a chromium-depleted metal surface. In order to restore full corrosion resistance, chemical or mechanical clean-up techniques must remove not only the oxide, but also a very thin layer of metal. Laboratory and field test studies show that these factors are particularly significant in less highly alloyed steels. Annealing stainless in a reducing atmosphere (bright annealing) avoids chromium depletion, but as-bright-annealed material does not display optimum corrosion resistance in certain environments. Electro passiva-tion can be applied to improve pitting resistance without significantly changing bright surface appearance. Potentiometric studies show that electropassivated material also displays significantly greater resistance to breakdown of passivity in acid solutions. The application of special surface finishes for appearance purposes can affect corrosion resistance. Roughness is a key factor. Samples of related appearance but with different surface profiles can show significant differences in corrosion resistance. Thus nonreflec-tive stainless with a relatively smooth surface produced by a special rolling process is much superior to material chemically etched to a similar low reflectivity. THE corrosion resistance of a stainless steel is affected by other factors in addition to its bulk composition and metallurgical structure. These other factors include those relating to the specific chemical and physical condition of the steel&apos;s surface. This paper will consider certain aspects of surface condition in relation to corrosion resistance. In particular, studies will be described on the effects of oxidation encountered in heat treating or welding operations, of passivation after bright annealing, and of different surface finishes. EFFECTS DUE TO OXIDATION When stainless steels are exposed to high temperature in an oxidizing environment, as in annealing or welding, the oxides formed are relatively rich in chromium. As a consequence of oxidation, the metallic layer directly beneath the scale may be low in chromium to some very thin but finite depth.1"8 Such a change in chromium content could lower the corrosion resistance at the surface, whether or not the oxide layer is removed. Studies were performed relating to the effect of oxidation and chromium depletion produced during annealing and welding on the corrosion resistance of stainless steels. The nominal compositions of steels used in this study and others are given in Table I. A) Annealing Studies on 17 pet Cr Steels. 1) Effects of Pickling Treatments. Studies were performed to investigate the corrosion resistance of air annealed type 430 stainless as a function of the amount of electrolytic pickling after annealing. The material used in this study had been air annealed and electrolytically pickled in the mill. All scale had been removed, and yet the material showed unusually poor corrosion resistance. Laboratory electrolytic pickling studies were performed to determine whether additional metal removal from the surface would improve corrosion resistance. Electrolytic pickling was performed in a sulfuric acid bath using various conditions of bath acidity, temperature, time, and current density. The samples were then rated for corrosion resistance in a ferric chloride spot test. For this spot test, a solution was prepared by dissolving 10 g of FeCl3 . 6H2O, 5 g of NaCl, and 2.5 ml of concentrated HC1 in 200 ml of water. An area on a specimen was cleaned and a drop of test solution was placed on the prepared area. After 5 min, the drop was rinsed off and the area wiped dry. The spot was then rated between 1 and 5 by visual comparison with standard spots. The numerical rating of the standard spots can be described as follows: 1—No clouding of surface; 2—very slight clouding of surface; 3—slight clouding of surface; 4—moderate clouding of surface; 5—strong clouding of surface. A rating of 1 or 2 was considered to have passed the test, a rating of 4 or 5 represented failure, and a rating of 3 was considered borderline. The severity of etching in this test has been related to the actual chromium content at the surface.4 Etching (clouding) occurs on type 430 stainless (rating of 4 to 5) when the surface chromium content is 14 pct or less. The effects of current density and retention time when electrolytically repickling this material in 6 pct sulfuric acid are shown in Fig. 1. Increasing the cur-rent density or retention time improved corrosion resistance as measured by the spot test. Similarly, increasing acid concentration of the bath or bath tem-perature was found to improve corrosion resistance. The conditions making for improved spot ratings resulted in increased metal removal, regardless of specific pickling conditions used, Fig. 2.

Jan 1, 1970

By R. R. Vandervoort

The creep behavior of Nb(Cb), Ta, Mo, and W was determined under conditions of constant atomic dif-fzisivity, constant stress to elastic modulus ratio, and nearly equivalent grain size, and the steady-state creep rates obtained from these tests were correlated with calculated stacking fault energies for the metals. These results, in conjunction with similar data for several fccMetals,13 suggest that stacking fault energy may influence the creep strength ofbcc metals. The interrelationship between steady-state creep rate, subgrain size, and stacking fault energy was examined. It was found that the subgrain size for a given creep stress, increased as stacking fault energy increased, but that this relationship did not cormpletely account for the effect of stacking fault energy on creep rate. The crystallography and energetics of stacking fault formation in bcc metals has been discussed by a num-ber of authors,1-5 and impurity stabilized stacking faults on (112) planes have been observed in Nb,6,7 w,8,9 Fe,] and V" by transmission electron microscopy. However, a crucial question is whether or not stack-ing faults influence the mechanical strength of bcc metals. Potentially, stacking faults could increase strength by reducing the mobility of the partial dis-locations bounding the fault, by acting as barriers to slip dislocations, and by retarding the climb of dislo-cations during high-temperature deformation. The objective of this study was to seek a correlation be-tween creep strength and stacking fault energy for several bcc metals; namely, Nb, Ta, Mo, and W. The creep behavior of most polycrystalline metals and alloys at high temperatures and moderate stresses can be described by the following relation:11,12 im=Af(s) where i, = minimum creep rate, A = constant, j(s) = a function involving metallurgical structure, a = applied stress, E = average elastic modulus at the test tempera-ture, w = constant (equal to 5 for most pure metals), D = diffusion coefficient. One factor in the structure function F(s) which sig- R. R. VANDERVOORT, Member AlME is Research Metallurgist, Process and Materials Development Division, Chemistry Department, Lawrence Radiation Laboratory, University of California, Livermore, Calif. Manuscript submitted February 28, 1969. IMD nificantly affects the creep resistance of fcc metals is stacking fault energy, and creep rate has been shown to vary directly with stacking fault energy to the 3.5 power." In the latter investigation, four fcc metals of widely different stacking fault energies (Ag, Cu, Ni, and Al) were creep tested at a constant stress to modulus ratio of 1.21 x 10-4, at a constant diffusivity of 2.7 x 10-12 sq cm per sec, and at nearly equivalent grain sizes of about 0.7 mm. The creep data were then correlated with stacking fault energies. In the present study, a similar procedure was followed. All materials used in this work were consolidated by powder metallurgy techniques. Impurity contents in the as-received materials are listed in Table I. Chemical analyses showed that no measurable contamination of the test specimens occurred during pretest annealing treatments or creep testing. Specimens with a gage section 0.75 by 0.125 by 0.050 in. were creep tested in tension in a vacuum of less than 10-9 torr. Deformation at temperature was measured by tracking fiducial marks on the gage section of the specimen with an optical comparator. Optical deformation measurements also permitted observation of the macroscopic characteristics of the deformation Table I. Typical Specimen Impurity Content, ppm Nb Ta Mo W C 45 10 155 6 O 185 30 4 10 N 30 6 3 2 H 5 I 1 <1 als 3 10 2 15 Ca <5 I3 5 Cr 5 <3 10 <5 Cu 10 50 2 15 Fc 10 10 150 35 Ni 2 150 20 <5 Si <I0 1 3 <10 Ta 100 Ti 10 8 1 Zi 15 50 1 3 Table II. Test Conditions for Constant Stress-Modulus Ratio of 6 X 10.&apos; and Constant Diffusivity of 2.7 X 10-12 sq cm per see, and Grain Size Values for the Given Pretest Annealing Treatments Literature references Pretest Annealing for E and D Treatment Stress, Temperature, ___"&apos;Values__ Grain Tempera-Metal psi "C E D Size, mm ture, .C Time hr Nb 745 1525 14 15 to 17 0.83 1650 I Ta 1220 1770 18 19.20 O.91 1800 I Mo 1975 1630 18 21 0.77 2200 I W 2140 2265 18 22 040 2400 5

Jan 1, 1970

By C. F. Jenkins, G. V. Smith

Serrated plastic flow in stable austenitic alloys based on Fe/Ni has been shown to be related to the presence of carbon and/or chromium in the systems. Strength peaks and plateaus in the serrated-flow temperature region for a commercial alloy correlate with an increased dislocation content, arising, presumably, from enhanced multiplication as a result of a strong interaction between dislocations and solute atoms. The data generally support a mechanism controlled by migration of vacancies, with the energy for vacancy motion being modified by the presence of chromium. Chromium atom -dislocation interaction is responsible for effects above 500°C, whereas the defect interacting with dislocations between 200" and 500°C is suggested to be a carbon-vacancy Pair. ThE phenomenon of jerky flow, serrated flow, or the Portevin-le Chatelier (P-C) effect in austenitic stainless steels is usually attributed to substitutional at1,2 mospheres1,2 or to precipitates&apos;-4 which form at dislocations during plastic deformation. On the other hand, evidence exists which supports a direct inter-stitial-dislocation interaction mechanism for serrated flow in fcc Ni-C,5,6 Ni-H7-9 and in nickel-austenites containing carbon." The present work consists in a study of serrated plastic flow in stable austenitic al-loys. The effects of carbon and of chromium were investigated separately, and a commercial stainless steel with different levels of interstitial impurity concentration was studied in an attempt to delineate the combined effects of the alloying elements. EXPERIMENTAL TECHNIQUES a) Materials and Fabrication. A commercial AISI 330 stainless steel and several specially prepared aus-tenitic alloys have been studied. The experimental alloys were prepared by arc melting the constituents under purified argon. Analyses of the materials are given in Table I. The commercial alloy was obtained as 5/8 in. bar stock and rolled to 0.092 in. sq, with several intermediate anneals. At this stage some of the material was annealed in Pd-purified hydrogen at 1100°C to establish different levels of interstitial content. All other heat treatments were in vacuum (10-5 torr). The "pure" alloy ingots were swaged to 0.120-in. rod and annealed in Pd-purified hydrogen at 1100°C. The analyses for these conditions are also contained in Table I. Following the above treatment, the final wire sizes Table I. Chemical Analyses of Test Materials Hrin Hydrogen at Cr, Ni, Alloy 1lOO°C wt pct wt pct C, ppm* N, ppm* Type 330 As-received 14.78 33.25 430 300 Type 330 64 14.78 33.25 40 50 Type 330 200 14.78 33.25 27 21 Fe/35 Ni 72 - 35.10 <10 62 Fe/35 Ni 200 35.10 <I0 44 Fe/35 Nil15 Cr 72 14.95 34.94 <I0 61 Fe/35 Ni/15Cr 200 14.95 34.94 <10 45 Fe/35 Ni/C $ 35.OM 380 *Sensitivity: N t 5 ppm Ct10ppm. f Nominal Ni content. % A master NiC alloy was used in preparation of this material; courtesy of D.E. Sonon. were obtained by either swaging or cold drawing. The test results did not vary with these techniques. b) Specimen Preparation. Two sizes of specimen and two gripping systems were used. i) 0.070-in. wire with a chemically milled gage section: 0.75 in. long, 0.060 in. in diam. These were fastened into grips containing tapped grooves. ii) 0.050 in. wire, gage length 1.5 in. Ball bearings were welded to the ends of the wires and the gage length was taken to include all material between the welds. Socket-type grips were used with these specimens. With specimens of type ii), joining was performed in a specially constructed brass jig, under argon, and automatic timing was utilized in the procedure. No adverse effects of welding were noted. Specimens were encapsulated and solution treated for 1 hr at temperatures selected to produce the same average grain size, -50 µ. Annealing twin boundaries as well as normal crystal boundaries were counted. The temperatures used are listed in Table 11. Table 11. Specimen Size. Temperature of Heat Treatment and Resulting Grain Diameters for Test Materials Recrystallization Resulting Material Condition Temperature Grain Sue AISI 330 Not H purified 0.070 120O°C 45 to 55µ in, wire AlSl 330 H , pure, 0.070 in. 1150°C 45to55µ wire Fc/35Nil15Cr Pure, 0.070 in. wire 1000°C 45tossp Fe/Ni Pure. 0.070 in. wire 775°C 45 to 55µ Fe/Ni/C Pure, 0.050 in. wire 850°C 10 to 20p AlSl 330 Not purified, 0.050 1150CC 45to55p in. wire AlSl 330 ti, pure, 0.050 in. 1150°C 45to55p wire

Jan 1, 1970

By F. George, W. Tice, M. Salkind

It was found that Al-A13Ni could be readily cold rolled perpendicular to but not parallel to the whiskers. Reductions of more than 98 pct were achieved without cracking by rolling perpendicular to the whiskers, whereas extensive edge cracking was noted after only 15 pct reduction when rolling parallel to the whiskers. The longitudinal and transverse tensile strengths were nearly doubled, and the longitudinal yield strength more than tripled by cold rolling 50 pct in a direction perpendicular to the whiskers. The whiskers exhibited some waviness (elastic bending) as a result of cold rolling, but at very high reductions (greater than 75 pct) whisker fracture and misalignment became significant. A fine dislocation substructure in the matrix consisting of cells attached to the whiskers was pro -duced by cold rolling. Most of- the substructure was readily removed by a 1-hr anneal at 500°C. Cold rolling was found to substantially reduce the thermal stability of the microstructure at 610°C but did not affect the stability at 500°C. FIBER and whisker reinforced composite materials promise significant improvements in properties over conventional materials. Before they find wide use, however, it will be necessary to understand the response of these highly anisotropic materials to common metalworking processes. Most of the nonmetal-lic fiber reinforced materials have very low elongations (a few pct or less) in the direction of fiber alignment. Thus, metalworking techniques such as rolling and forging would not be as broadly applicable to these materials. This investigation was initiated to determine how a composite system consisting of Al3Ni whisker reinforced aluminum responded to rolling, what changes in the microstructure occurred, and the effect of deformation on the mechanical properties. The composite material studied was produced by unidirectional solidification of the A1-Al3Ni eutectic alloy&apos;-7 and consisted of 10 pct by volume of aligned whiskers of Alai in a matrix of aluminum. It should be pointed out that this system is not representative of all composite materials, and the results will therefore not be universally applicable. The A1-Al3Ni system is characterized by: 1) A strong fiber-matrix interfacial bond 2) A ductile matrix 3) A sufficiently low fiber content to allow significant plastic flow between fibers 4) Strong, completely elastic whiskers (tensile strength 400,000 psi, elastic modulus = 20 X 106 psi.1 These factors allow the material to be readily rolled perpendicular to the fibers. If the fiber-matrix bond were not strong, such a weak interface could fail during rolling. A measure of the ability of a composite to be rolled in the transverse direction can be obtained from noting the transverse tensile behavior. In the case of Al-Al3Ni,2 there is considerable ductility (15 to 30 pct). In the case of boron filament reinforced aluminum, for example, the transverse elongation is less than 1 pct,8 and the material could probably not be cold rolled as readily in that direction. EXPERIMENTAL PROCEDURE 3-in. diam ingots of A1-A13Ni eutectic were unidi-rectionally solidified in graphite crucibles. The starting materials consisted of 99.99+ pct pure nickel and aluminum, and the pure eutectic ingots were made with 6.2 wt pct Ni. The unidirectional solidification process (described in detail elsewhere1-3) consists of preparing a master heat of eutectic composition, remelting, and withdrawing the ingot vertically downward through the heat source at a controlled rate so that plane front solidification proceeds upward at a constant velocity. The resulting microstructure consists of 10 pct by volume of whiskers of very high aspect (length to diameter) ratio. The fiber lengths have not been measured because of the difficulty of detecting fiber ends9 but exceeds 104. There is some possibility that the fibers may be continuous within one grain. Flat sheet specimens 2¾ in. sq and approximately 0.2 in. thick containing whiskers parallel to the plane of the sheet and to one edge were used for this study. A1-A13Ni exhibits either a rod-like (high solidification rates) or a blade-like (low solidification rates) whisker morphology,1,3 and both types were studied. Rolling was accomplished using a two-high rolling mill at a speed of approximately 10 fpm. The rolling direction was either parallel to or perpendicular to the direction of growth (direction of whisker alignment). Reductions of from 0.002 to 0.03 in. per pass were used with the most common value being 0.005 in. per pass. Cold rolling of Al-Al3Ni to more than 98 pct reduction in thickness was accomplished with no intermediate anneals. In addition. a series of speci-mens was cold rolled 97 pct with a 1-hr, 500°C anneal in air after each 50 pet reduction. Tensile testing was accomplished using a Tinius-lsen four screw testing machine. Flat sheet specimens + in. wide and between 2 and 2; in. long with the thickness dependent upon rolling reduction, were used. The gage section was in. wide and 1 in. long. Strain was measured using a clip-on LVDT extensome-

Jan 1, 1970