Search Documents

By G. S. Hume

Production of petroleum and natural .gas increased in Canada in 1940 over the previous year. Alberta produced more than 97 per cent of the total Canadian production of 8,718,053 bbl. of oil, an increase for this province of nearly 12 per cent, whereas in Ontario and New Brunswick, where the production is relatively small, there was a slight decline. In Alberta the main producing field is Turner Valley, on the eastern edge of the foothills southwest of Calgary, and development continued in this field in 1940 with the completion of 36 wells, all of which obtained production. In the Red Coulce field, close to the International Boundary, near Coutts, no new wells were drilled and the seven producing wells showed a decline of 900 bbl. below the previous year. Also, in the Wainwright field of east central Alberta, four wells, yielding heavy crude oil, produced 4000 bbl. less oil than in 1939, owing possibly rather to discontinuous operation than to actual decline in potential yield. This decline was more than offset by production from a new field 40 miles northeast of Wainwright, at Borradaile, producing oil of 14" to I 5° A.P.1. There was a small increase in production during 1940 from the Del Bonita field, in southern Alberta, where the production is from two wells. The outstanding development of the year was the completion of Standard Oil Princess No. 2 well in the Steveville area, on the Plains 100 miles east of Calgary. This well was completed late in December with an initial flow1 of 520 bbl. of 26.3" A.P,I. oil, and 12,750 M cu. ft. of gas from the upper part of the Mississippian limestone. It has opened up a new field and given a further proof of the potentialities of the Southern Plains. The production of petroleum in Canada is shown in Table I. Since most of the yield comes from Alberta, the production is shown from the various fields in Table 2. The sale value of the petroleum produced in Canada in 1940 exceeded 11.1 million dollars, which is still somewhat less than the value of the natural gas production, shown in Table 3. Table i.—Production of Petroleum in Canada" Barrels Province 1939 1940 New Brunswick........ 20,101 21,161 Ontario............... 206,196 186,471 Alberta............... 7,595,000 8,493,237 Northwest Territories. . 17,013 8,493,23717.184 Total............... 7,838,310 8,718,053 Value............... $10,353,351 $11.113,000 0 Bureau of Statistics, Ottawa. Turner Valley, Alberta Turner Valley continues to be by far the largest producing field in Canada (details are given in Table 4), The limits of the Pr in- field are now Known. On the east the oil area is bounded by the gas cap, which in turn is cut off on its east side by a major overthrust fault; on the west, ii is defined by edge water at a level of 4roc

Jan 1, 1941

By Arthur Wade

The most important development in connection with the search for oil in Australia during 1940 was on the legislative side. Prior to 1939 legislative enactments in the various states with regard to prospecting for petroleum were such as to prohibit large-scale effort and to bar the major oil companies from operating. The preparation of the Wade Model Bill for the Commonwealth Government in 1939 and the acceptance of the Bill in principle by all States, has gone far to remove these obstacles. Amending Acts, largely based on the Alodel Bill, have now been passed by all States with the exception of New South Wales and Tasmania. In New South Wales an Amending Bill is being drafted, while the Govern-ment of Tasmania is preparing to introduce an Amending Bill provided there is any demand for it. Noteworthy developments followed immediately on the passing of these Amending Acts. The Shell Company (1)1 and the Superior Oil Company of California (2) too$ up large areas in Queensland and com-menced work during 1940. Caltex acquired a big tract of country in the Kimberley district of Western Australia (3) and has made application for an area in the Territory of Papua. An Australian company, The Phoenix Oil Extraction Co., has obtained a permit to prospect over an extensive area bordering the south coast of Western Australia (4). Other developments are foreshadowed. The Shell Company is making an intensive examination of its area in Queensland (I). Geological, geophysical and aerial surveys are in progress. Caltex has three geological parties in the held in Western Australia while Superior Oil Company of California has done some geological work in the interior of Queensland (2). None of these concerns envisages a drilling campaign in the near future. Much exploratory work is necessary. Further work has been done by the companies that were already operating in 1939, though an important Australian company - Oil Search—has abandoned the work of prospecting in Australia. This company has subleased its holdings, at North West Cape in Western Australia (;), to Caltex on a royalty basis. The company also maintains its holdings in, and connection with, the Australasian Petroleum Company Proprietary Limited, which is a combination of Standard Oil (New Jersey), Anglo-Iranian and Oil Search. This company is operating in the territories of Papua and New Guinea. Drilling Victoria.—Although a good deal of drilling was done in the LaBes Entrance Tertiary Basin of Victoria (7), no appreciable production of oil was obtained. In order to test the extent and possibilities of the oil-bearing sand in this region, the Commonwealth and State Governments jointly put down six scout boreholes to depths of between 1200 and I500 it. The results were nega tive. A deeper exploratory horehole put down by the Governments at Seacornbe, or 26

Jan 1, 1941

By Arthur Wade

The most important development in connection with the search for oil in Australia during 1940 was on the legislative side. Prior to 1939 legislative enactments in the various states with regard to prospecting for petroleum were such as to prohibit large-scale effort and to bar the major oil companies from operating. The preparation of the Wade Model Bill for the Commonwealth Government in 1939 and the acceptance of the Bill in principle by all States, has gone far to remove these obstacles. Amending Acts, largely based on the Alodel Bill, have now been passed by all States with the exception of New South Wales and Tasmania. In New South Wales an Amending Bill is being drafted, while the Govern-ment of Tasmania is preparing to introduce an Amending Bill provided there is any demand for it. Noteworthy developments followed immediately on the passing of these Amending Acts. The Shell Company (1)1 and the Superior Oil Company of California (2) too$ up large areas in Queensland and com-menced work during 1940. Caltex acquired a big tract of country in the Kimberley district of Western Australia (3) and has made application for an area in the Territory of Papua. An Australian company, The Phoenix Oil Extraction Co., has obtained a permit to prospect over an extensive area bordering the south coast of Western Australia (4). Other developments are foreshadowed. The Shell Company is making an intensive examination of its area in Queensland (I). Geological, geophysical and aerial surveys are in progress. Caltex has three geological parties in the held in Western Australia while Superior Oil Company of California has done some geological work in the interior of Queensland (2). None of these concerns envisages a drilling campaign in the near future. Much exploratory work is necessary. Further work has been done by the companies that were already operating in 1939, though an important Australian company - Oil Search—has abandoned the work of prospecting in Australia. This company has subleased its holdings, at North West Cape in Western Australia (;), to Caltex on a royalty basis. The company also maintains its holdings in, and connection with, the Australasian Petroleum Company Proprietary Limited, which is a combination of Standard Oil (New Jersey), Anglo-Iranian and Oil Search. This company is operating in the territories of Papua and New Guinea. Drilling Victoria.—Although a good deal of drilling was done in the LaBes Entrance Tertiary Basin of Victoria (7), no appreciable production of oil was obtained. In order to test the extent and possibilities of the oil-bearing sand in this region, the Commonwealth and State Governments jointly put down six scout boreholes to depths of between 1200 and I500 it. The results were nega tive. A deeper exploratory horehole put down by the Governments at Seacornbe, or 26

Jan 1, 1941

By James Terry Duce

The symposium on production for the year 1940 contains few papers on the foreign situation. It is probable that the foreign part of next year's symposium will be even shorter. This is due to rigid censorship in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even more true than in the last war, owing to greater mechanization of armies. 'It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable frod data available to the author, please inserty; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In sucli cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved') and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1941

By James Terry Duce

The symposium on production for the year 1940 contains few papers on the foreign situation. It is probable that the foreign part of next year's symposium will be even shorter. This is due to rigid censorship in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even more true than in the last war, owing to greater mechanization of armies. 'It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable frod data available to the author, please inserty; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In sucli cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved') and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1941

By P. P. Gregory

Natural petroleum gas occurring in the oil-bearing reservoirs is found to exist either as free gas associated with the oil and/or in solution in the oil. In some virgin fields practically no free gas is encountered under the reservoir conditions of pressure and temperature, although in other fields a considerable section of the "pay" horizon is occupied by free gas. In other words, a given oil field may or may not have a gas cap before the exploitation takes place. However, when the reservoir pressure is reduced to a point below the critical saturation pressure by withdrawals of fluids from the producing formation, the gas dissolved in the oil inevitably begins to come out of solution and becomes free gas. Under the controlled methods of production and drilling, a portion of this gas is produced with the oil to the surface and a portion of it remains within the reservoir to accumulate at higher structural levels toward which it migrates by virtue of its low specific gravity. The rate of growth of a gas cap in a given structure depends primarily upon the rate of decline in the reservoir pressure. If the rate of pressure decline is rapid, the gas cap likewise will grow rapidly. On the other hand, shrinkage in the gas-cap area was noted in some fields in which reservoir pressures wereincreasing. Determination of Gas-oil Contact and Thickness of Gas Cap The gas-oil contact can be conveniently located in the process of drilling a well and by electrical logging. However, very little can be found in the petroleum literature concerning methods of predetermining gas-oil contacts in producing reservoirs. Therefore, the writer feels justified in describing briefly a simple, workable, and inexpensive method of determining gas-oil contacts and outlining the limits of gas-cap areas in a field where such knowledge may be essential for efficient production and development operations. The method involves the determination of the following data: (I) Structural data, such as the depth or elevation of the top' of "pay" horizon; (2) reservoir pressures; (3) tubing and casing pressures at the well head; (4) static oil-pressure gradient; (5) static gas-pressure gradient. These data can be secured with a minimum of expense, inasmuch as the

Jan 1, 1938

By F. Cadena

Hiwassee Darn, now under construction by the Tennessee Valley Authority on the Hiwassee River, a tributary of the Tennessee River, will require aggregate for approximately 800,000 cu. yd. of concrete. Near the damsite deposits of natural sand or gravel are not available and graywacke, a rock that is found in abundance, suggested itself as a likely source of manufactured aggregate. Graywacke is a metamorphosed sandstone composed principally of a mixture of quartz (65 per cent), mica (25 per cent), and feldspar (10 per cent). Other minerals are present in negligible amounts. The rock varies in different parts of the quarry from very fine to a coarse grain containing particles of about ¼ in. maximum size, although the bulk of the deposit is medium grain. Extensive tests showed that graywacke would be suitable as a source of both coarse and fine aggregates. The aggregate plant available for use at Hiwassee Dam consisted of the coarse-aggregate and sand plant used on the Norris project. The coarse-aggregate plant had also been used at Chickamauga Dam. Although most of this plant equipment is now in use at Hiwassee, the present flowsheet is not only different from that at Norris and Chickamauga but is also unique as compared to the flowsheet of the average crushed-stone aggregate plant. It is hoped that this paper will show the importance of proper arrangement of equipment if the optimum in flexibility and capacity is to be attained. Flowsheet Rock is ioaded by 3-yd. electric shovels into 12-yd. dump trucks, which carry the rock to the primary crusher, a 42-in. Superior McCully gyratory unit set at 4¾ in. (Fig. 1). The primary crusher discharges directly onto a 42-in. inclined belt conveyor, which carries the product to a surge storage pile with a maximum live storage capacity of approximately 3000 tons. A concrete tunnel under this storage pile houses the feed end of a 36-in. belt conveyor (conveyor B) fed by a 36 by 66-in.

Jan 1, 1942

By F. Cadena

Hiwassee Darn, now under construction by the Tennessee Valley Authority on the Hiwassee River, a tributary of the Tennessee River, will require aggregate for approximately 800,000 cu. yd. of concrete. Near the damsite deposits of natural sand or gravel are not available and graywacke, a rock that is found in abundance, suggested itself as a likely source of manufactured aggregate. Graywacke is a metamorphosed sandstone composed principally of a mixture of quartz (65 per cent), mica (25 per cent), and feldspar (10 per cent). Other minerals are present in negligible amounts. The rock varies in different parts of the quarry from very fine to a coarse grain containing particles of about ¼ in. maximum size, although the bulk of the deposit is medium grain. Extensive tests showed that graywacke would be suitable as a source of both coarse and fine aggregates. The aggregate plant available for use at Hiwassee Dam consisted of the coarse-aggregate and sand plant used on the Norris project. The coarse-aggregate plant had also been used at Chickamauga Dam. Although most of this plant equipment is now in use at Hiwassee, the present flowsheet is not only different from that at Norris and Chickamauga but is also unique as compared to the flowsheet of the average crushed-stone aggregate plant. It is hoped that this paper will show the importance of proper arrangement of equipment if the optimum in flexibility and capacity is to be attained. Flowsheet Rock is ioaded by 3-yd. electric shovels into 12-yd. dump trucks, which carry the rock to the primary crusher, a 42-in. Superior McCully gyratory unit set at 4¾ in. (Fig. 1). The primary crusher discharges directly onto a 42-in. inclined belt conveyor, which carries the product to a surge storage pile with a maximum live storage capacity of approximately 3000 tons. A concrete tunnel under this storage pile houses the feed end of a 36-in. belt conveyor (conveyor B) fed by a 36 by 66-in.

Jan 1, 1942

By C. E. Lesher

Low-temPeRatUre carbonization needs no introduction to the literature on coal. This paper will attempt no review of that literature; it tells the story of the commercial development of one of the processes for carbonizing coal at so-called low temperatures, dealing with the technology and economics of the process rather than with the design of equipment. The process used is that covered by the patents of C. B. Wisner, with improvements and changes made by the Pittsburgh Coal Carbonization Co. The important and novel feature of the process is the phenomenon of making the product in ball form (Fig. 1). Melting coal dust into smokeless solid fuel in an apparatus as simple as a revolving cylinder of ordinary mild steel has been proved to be practical. Furthermore, it has been found that the process has a wide application, for by applying a knowledge of why and how this balling action is accomplished, the apparatus can be designed and adapted to treat any coal that has a certain minimum agglutinating property. The operating plant is 20 miles west of Pittsburgh, adjacent to the Champion preparation plant of the Pittsburgh Coal Co. The coal used is cleaned minus ?-in. or finer sizes. The products are low-tem-perature coke, tar and tar products. Present capacity is 7000 tons per month of low-temperature coke and 140,000 gal. of tar. There is no surplus gas for sale, and none of the light oils are stripped from the gas. The coke is marketed in two sizes, 1 to 2 in. and 1 to 6 in., through retail coal dealers for domestic consumption in hand-fired furnaces, and for fireplace fuel. The smaller size is bagged by dealers. Crude tar and many distillates and road tars are sold. Acknowledgments During the 10 years in which the work that is summarized in this paper has been under way, many have contributed time and effort, faithful service and fruitful thinking. Whatever success has attended

Jan 1, 1940

By C. E. Lesher

Low-temPeRatUre carbonization needs no introduction to the literature on coal. This paper will attempt no review of that literature; it tells the story of the commercial development of one of the processes for carbonizing coal at so-called low temperatures, dealing with the technology and economics of the process rather than with the design of equipment. The process used is that covered by the patents of C. B. Wisner, with improvements and changes made by the Pittsburgh Coal Carbonization Co. The important and novel feature of the process is the phenomenon of making the product in ball form (Fig. 1). Melting coal dust into smokeless solid fuel in an apparatus as simple as a revolving cylinder of ordinary mild steel has been proved to be practical. Furthermore, it has been found that the process has a wide application, for by applying a knowledge of why and how this balling action is accomplished, the apparatus can be designed and adapted to treat any coal that has a certain minimum agglutinating property. The operating plant is 20 miles west of Pittsburgh, adjacent to the Champion preparation plant of the Pittsburgh Coal Co. The coal used is cleaned minus ?-in. or finer sizes. The products are low-tem-perature coke, tar and tar products. Present capacity is 7000 tons per month of low-temperature coke and 140,000 gal. of tar. There is no surplus gas for sale, and none of the light oils are stripped from the gas. The coke is marketed in two sizes, 1 to 2 in. and 1 to 6 in., through retail coal dealers for domestic consumption in hand-fired furnaces, and for fireplace fuel. The smaller size is bagged by dealers. Crude tar and many distillates and road tars are sold. Acknowledgments During the 10 years in which the work that is summarized in this paper has been under way, many have contributed time and effort, faithful service and fruitful thinking. Whatever success has attended

Jan 1, 1940

By Earnshaw Cook, J. A. Fellows, Howard S. Avery

Heat-resistant alloys of the higher nickel and chromium ranges have been empirically developed through the practical experience of the past two decades to a position of significant industrial importance. Few quantitative metallurgical data have been published, however, that could be related directly to engineering specifications and design. Inadequate information led to the inauguration, in 1934, of a research directed toward a better understanding of the properties and performance of these steels at temperatures between 1400° and 2000°F. Investigation was concentrated upon the 26 per cent Cr:I2 per cent Ni type, which owes its extensive application to an excellent combination of economy, strength and surface stability at elevated temperatures. The requirements of the oil-refining industry have been prominent in influencing the scope and evolution of the program. Creep strength at the maximum allowable deformation ranges has been employed to evaluate the merits of these alloys. Permissible elongation rates vary from 1.0 per cent in one million hours for turbine blades to I .o per cent in ten thousand hours for tube supports and heating-furnace equipment. Throughout this paper, the limiting creep stress (L.C.S.) for a given temperature has been defined as the stress that will produce a uniform elongation rate (stage 11) of one per cent in ten thousand hours as extrapolated from rates per hour for tests of less than two thousand hours duration. Certain current specifications require a minimum L.C.S. of 1600 lb. per sq. in. at I800°F., of 3600 lb. per sq. in. at 1400°F., and include a tensile acceptance test at room temperature, after aging for 24 hr. at 1400°F., as a measure of embrittlement in service. An elongation of 4 per cent is considered satisfactory for general use, while a minimum of 9 per cent is prescribed on occasion. Many differences of opinion concerning the properties and performance of these alloys appear to result from their sensitivity to unappreciated variations of chemical analyses which, for example, may change their L.C.S. from 3500 to 350 lb. per sq. in. at 1800°F. Within broad chemical limits, it is possible to balance the six or more important elements present to attain desirable properties with a number of different combinations. One method for adjusting the composition has been described under the sponsorship of the Alloy Casting Institute,' in which, by maintaining a substantially austenitic* alloy, optimum creep strength and minimum tendency to embrittle after aging are expected. Unless, however, the limits are undesirably close, it has not been possible to ensure a moderate range of strength and of ductility by any chemical specification alone. There is a definite need

Jan 1, 1942

By J. A. Fellows, Earnshaw Cook, Howard S. Avery

Heat-resistant alloys of the higher nickel and chromium ranges have been empirically developed through the practical experience of the past two decades to a position of significant industrial importance. Few quantitative metallurgical data have been published, however, that could be related directly to engineering specifications and design. Inadequate information led to the inauguration, in 1934, of a research directed toward a better understanding of the properties and performance of these steels at temperatures between 1400° and 2000°F. Investigation was concentrated upon the 26 per cent Cr:I2 per cent Ni type, which owes its extensive application to an excellent combination of economy, strength and surface stability at elevated temperatures. The requirements of the oil-refining industry have been prominent in influencing the scope and evolution of the program. Creep strength at the maximum allowable deformation ranges has been employed to evaluate the merits of these alloys. Permissible elongation rates vary from 1.0 per cent in one million hours for turbine blades to I .o per cent in ten thousand hours for tube supports and heating-furnace equipment. Throughout this paper, the limiting creep stress (L.C.S.) for a given temperature has been defined as the stress that will produce a uniform elongation rate (stage 11) of one per cent in ten thousand hours as extrapolated from rates per hour for tests of less than two thousand hours duration. Certain current specifications require a minimum L.C.S. of 1600 lb. per sq. in. at I800°F., of 3600 lb. per sq. in. at 1400°F., and include a tensile acceptance test at room temperature, after aging for 24 hr. at 1400°F., as a measure of embrittlement in service. An elongation of 4 per cent is considered satisfactory for general use, while a minimum of 9 per cent is prescribed on occasion. Many differences of opinion concerning the properties and performance of these alloys appear to result from their sensitivity to unappreciated variations of chemical analyses which, for example, may change their L.C.S. from 3500 to 350 lb. per sq. in. at 1800°F. Within broad chemical limits, it is possible to balance the six or more important elements present to attain desirable properties with a number of different combinations. One method for adjusting the composition has been described under the sponsorship of the Alloy Casting Institute,' in which, by maintaining a substantially austenitic* alloy, optimum creep strength and minimum tendency to embrittle after aging are expected. Unless, however, the limits are undesirably close, it has not been possible to ensure a moderate range of strength and of ductility by any chemical specification alone. There is a definite need

Jan 1, 1942

By Earnshaw Cook, H. S. Avery, J. A. Fellows

TEe increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloys presented in a companion paper. The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. The Creep Test Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test iaboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit I000-hr. tests in the temperature range of I200° to 2 200°F. with a choice of applied stress extending from jo to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10:I ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a I-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, zo per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of -construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with aludum cement; the distribution of turns is adjusted to give a maximum temperature gradient of , I°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used „ to reduce the temperature of the threaded joints and thus to facilitate removal from the grips. Thermal losses are minimized by refractory insulators cut to shape and surrounded by diatomaceous ear,th. The taps

Jan 1, 1942

By J. A. Fellows, Earnshaw Cook, H. S. Avery

TEe increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloys presented in a companion paper. The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. The Creep Test Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test iaboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit I000-hr. tests in the temperature range of I200° to 2 200°F. with a choice of applied stress extending from jo to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10:I ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a I-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, zo per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of -construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with aludum cement; the distribution of turns is adjusted to give a maximum temperature gradient of , I°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used „ to reduce the temperature of the threaded joints and thus to facilitate removal from the grips. Thermal losses are minimized by refractory insulators cut to shape and surrounded by diatomaceous ear,th. The taps

Jan 1, 1942

By J. T. Eash, E. M. Wise

Platinum and palladium are the most generally useful, most ductile and least rare members of the platinum family. They have many important applications in the pure state but for other applications it is frequently desirable to harden them and otherwise modify their properties by alloying small amounts of the other platinum group metals with them. These alloys are frequently required to withstand very drastic forming operations and to possess certain mechanical properties to fulfill specific requirements. For these reasons a knowledge of the tensile properties and annealing characteristics of pure platinum and palladium as well as their more useful commercial alloys is important to the user and the fabricator. The present work was undertaken to fill this need. Rather brief (5 min.) annealing treatments were employed to render the data of maximum practical value and all tests were conducted upon 0.050-in. dia. wire, initially reduced 50 per cent in area by cold drawing, for the same reason. Conclusions 1. Pure (thermocouple grade) platinum reduced 50 per. cent by cold drawing exhibits the following tensile properties: ultimate tensile strength, 36,000 lb. per sq. in.; proportional limit, 27,000 lb. per sq. in.; elongation, 2.5 per cent in 2 in.; reduction in area, 95 per cent. When fully annealed by treatment at 1100°C. its properties are: ultimate tensile strength, 20,700 lb. per sq. in.; elongation, 30 per cent in 2 in.; reduction in area, 93 per cent. 2. The addition of alloying elements in moderate amounts markedly increases the strength and annealing temperature without much detriment to the ductility. The behavior and properties of variously hardened platinum alloys are considered in some detail. The behavior of a 20 per cent iridium

Jan 1, 1935

By J. T. Eash, E. M. Wise

Platinum and palladium are the most generally useful, most ductile and least rare members of the platinum family. They have many important applications in the pure state but for other applications it is frequently desirable to harden them and otherwise modify their properties by alloying small amounts of the other platinum group metals with them. These alloys are frequently required to withstand very drastic forming operations and to possess certain mechanical properties to fulfill specific requirements. For these reasons a knowledge of the tensile properties and annealing characteristics of pure platinum and palladium as well as their more useful commercial alloys is important to the user and the fabricator. The present work was undertaken to fill this need. Rather brief (5 min.) annealing treatments were employed to render the data of maximum practical value and all tests were conducted upon 0.050-in. dia. wire, initially reduced 50 per cent in area by cold drawing, for the same reason. Conclusions 1. Pure (thermocouple grade) platinum reduced 50 per. cent by cold drawing exhibits the following tensile properties: ultimate tensile strength, 36,000 lb. per sq. in.; proportional limit, 27,000 lb. per sq. in.; elongation, 2.5 per cent in 2 in.; reduction in area, 95 per cent. When fully annealed by treatment at 1100°C. its properties are: ultimate tensile strength, 20,700 lb. per sq. in.; elongation, 30 per cent in 2 in.; reduction in area, 93 per cent. 2. The addition of alloying elements in moderate amounts markedly increases the strength and annealing temperature without much detriment to the ductility. The behavior and properties of variously hardened platinum alloys are considered in some detail. The behavior of a 20 per cent iridium

Jan 1, 1935

By M. F. Trice

Pyrophyllite is a hydrous aluminum silicate (A1²Si4O10(OH)²)1 that, occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.' The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey12 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, ('are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. Sources At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This belt varies from 8 to 50 miles in width. Two major deposits of pyrophyllite lie along its eastern boundary, in what is known as the Deep

Jan 1, 1942

By M. F. Trice

Pyrophyllite is a hydrous aluminum silicate (A1²Si4O10(OH)²)1 that, occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.' The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey12 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, ('are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. Sources At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This belt varies from 8 to 50 miles in width. Two major deposits of pyrophyllite lie along its eastern boundary, in what is known as the Deep

Jan 1, 1942

By J. C. Reed, J. M. Hansell

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935

By J. C. Reed, J. M. Hansell

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935