Search Documents

By Connie Postupack

The purpose of the workshop is to show the effect of various blasting factors on the overall results.

Jan 1, 1994

By J. Chai, Q. Yuan, B. Qiu

"Overburden strata deformation monitoring is one of the key problems in ground control. Using geophysical method through surface drilling to detect strata deformation is commonly used in the industry. In this paper, a geophysical method based on the distributed optical fiber sensing (DOFS) system were conducted in the laboratory, where a DOFS-based strata deformation monitoring experiment was performed with three physical models. The results show that the DOFS method precisely detects the rock mass deformation and strata structure forming with the Brillouin frequency shifts (BFS) representation. The BFS curves are divided into three phases, which reflects the horizontal three zones developed in the overburden. The BFS distribution presents a multiple stages form, the 1st stage corresponds to the caving zone and the 2nd stage corresponds to the fracture zone. Based on the multiple stages form, the evolution of the water flowing through fractured zone have been determined and the controlling effect of key strata over the water flowing fracture has been pointed out. In the end, the comparison validation proves the accuracy and reliability of this method, and it could be a new approach for the ground control research. INTRODUCTION Overburden rock strata above the work face space will propagate from slight deformation, part destruction to violent movement because of the underground coal mining. It is fundamental and an intrinsic requirement of ground control to monitor the mining-induced rock mass deformation.[1] Overburden strata have their significant mechanical behaviors and movement under damage deformation and fracture. Overburden strata deformation affect the mining ground pressure control directly, and performance in the relationship of supporting equipment and the surrounding rock, the mining-induced fracture distribution and the loss of underground water resource, the ground surface structure stability and the ecological environment.[2] From the perspective of the concept of safe and efficient scientific coal mining: the overburden strata deformation is an important part of mining method selection and reasonable supporting solutions decision which can solve the issues like the roof supporting force calculation, overburden fracture distribution and gas drainage, ground subsidence, separation of coal and rock control and top-coal recovery rate and so on. From the perspective of green and ecological mining: the overburden strata deformation is the key basis of studying the mining-induced ground subsidence and mining area ecological damage, and such engineering problem like environmental protection in mining area, ecological restoration in mining subsided land and the water conservation in fragile ecology area of mining could be solved based on it.[3-6] Therefore, the mining-induced overburden strata deformation is the key of ground control and needs to be controlled artificially."

Jan 1, 2017

By Fangtian Wang

The fully mechanized longwall mining was employed in a shallow coal seam that was under the gobs of room and pillar mining and overlain by thin bedrock and thick loose sands. Operational practices have demonstrated that severe accidents would occur including roof structure instability, roof steps, damages of shield supports, and face bumps triggered by the large area roof weighting, resulting in serious threats to the safety of underground miners and equipment. This paper uses Shigetai Mine, located in the Ordos area, Inner Mongolia, as the study site. It fully considers the geological conditions of 3-1-2 coal seam and employs theoretical analysis, 3DEC numerical simulation, and field measurements to analyze the overlying strata movement for the shallow seams under an abandoned room and pillar mine without pillar extraction. The research results serve as an excellent guide to mining in similar geological and mining conditions.

Jan 1, 2014

By Haitao Wang, Shen Wang, Dongyin Li, Yongjia Xu, Jinzhao Liu, Xiangjun Chen

The safe and efficient driving of the roadway along the gob is becoming an increasing challenge due to the influence of the integrity and bearing capacity of the side coal and rock mass in the gob under the roof cutting mining mode. The mechanism of protection of the gob-side roadway is shown by modeling the influence of roof cutting and the application of a destress technique on the lateral coal and rock mass zones. The distribution characteristics of stress, displacement, and fracture in the overburden are analyzed by numerical simulation method under the three working conditions. The results indicate (1) construction of row holes and blasting can form artificial structure’s fracture plane above the roadway, which can effectively cut the connection of overburden. The artificial structure’s fracture plane decreases the peak value of the lateral coal body’s support pressure. The peak point and the critical location of the stress reduction area are both transferred to the deep part at the same time, providing adequate space for the gob-side roadway. (2) The stress arch foot in the lateral rock mass rises to the rock layer at the bottom of the roof cutting plane after top cutting, as does the high-pressure area of deviator stress. The fracture plane prevents lateral coal and rock mass instability and limits the negative effects of roof deformation above the gob-side roadway. (3) The triangle slip fracture zone moves to over the roof cutting drilling zone due to the fracture plane, showing a high position compared to its original zone.

Jul 11, 2023

By Lumley G, Rowlands D

The overburden slusher (OS) is proposed as a stripping tool that is expected to find application in overburden stripping operations including open cut coal and oil shale mines. OS is expected to combat the effects of increasing depth on the productivity of conventional dragline stripping.Although previously developed stripping techniques have included the use of drag scrapers the OS is sufficiently different as to constitute a new stripping method.A study undertaken at the University of Queensland during 1985 is believed to be the first major study on the use of the OS and preliminary economic results are very encouraging. It appears that the OS has the capacity to remove overburden at a cheaper unit cost than the equivalent powered dragline stripping machine at any comparable depth of overburden. The OS is not adversely affected by increasing stripping depth to the same extent as a dragline. In addition, the action of the OS machine allows for the lowering of spoil face angles, thereby reducing spoil slope stability problems encountered in deep open cut strip mines.

Jan 1, 1986

By Wenquan Zhang

Based on the mining and geological conditions of Wadong Mine, Longkou City, Shandong Province, China, a viscoelastic model with proper creep parameters was established. The 3-D ANSYS was used to simulate surface subsidence, analyze overburden subsidence characteristics, and propose the rational mining and pillar widths for mining in weak rocks and under special mining conditions, and provide the policy makers scientific data for decision making on mining activities.

Jan 1, 2006

By Koppe J. C, Costa J. F C L

This paper compares different results for overburden volume estimation assisted by geoestatistics, particularly using kriging methods. The main goal is to obtain the most reliable digital terrain model for the calculation of the overburden volume. The data was collected on an irregularly spaced grid and interpolated values were calculated to provide a denser, more regular data set before volume estimation. The field work was developed at the Butia-Leste Coal Mine, southern most Brazil, where an accurate survey was done using a total station theodolite with electronic data collector. The study was developed in five main steps: data acquisition, exploratory data analysis, spatial continuity measurements, point and block kriging estimation and verification of the results. Data acquisition was carried out on a 5 x 5 in grid. This dense grid provides an exhaustive data set of the real terrain against which data subsets can be compared for the various interpolation procedures and volume calculation. This provides an interesting insight into the influence of the number of data on the estimation error. Univariate statistics were used to compare each data subset and the exhaustive dataset. Ordinary kriging on the data subsets followed by contouring was carried out using Geoeas and Surfer software respectively. A subroutine written in C provided the link between the files generated in Geoeas and subsequent contouring routines embedded into the Surfer package. Omnidirectional and directional variograms were modelled defining the parameters for kriging estimation using Geoeas. Different variogram models were checked through cross validation prior to kriging. A comparison between the magnitude of the differences in volumes calculated with the different DTMs was attained. These final result indicates the sensitivity of the volume obtained to the number of data points. As the number of data points increases the estimation error decreases, but at some point there is no significant decrease in the final volume with the collection of additional data.

Jan 1, 1995

By Tim Brick, Peter Jewell, Stephen Thompson, Simon Morgan

The $980m (€750m) Dublin Port Tunnel, Europe’s biggest urban highway tunnel project, was opened in December 2006. The culmination of this immense scheme is set to transform the environment, mobility and road safety of Ireland’s capital city. This paper summarizes the key aspects of a project linking both sequential and parallel construction of individual tunnels and describes various approaches to bored, mined and pre-support cut-and-cover tunneling in a wide variety of ground types and depth of cover. Examples of innovative approaches to deal with structural and geotechnical problems while maintaining full operation of both road and rail traffic and the integrity of properties in a dense urban corridor are described.

Jan 1, 2007

By Jared M. Green

This paper presents the wall stabilization design and implementation for a 541 linear ft masonry and concrete gravity-type retaining wall flanking the west perimeter of a 7.37 acre parcel in Bronx, New York. This paper will discuss the results of static and dynamic stability analyses performed for the pre- and post excavation phases for the proposed 300 ft wide open-cut of up to 14 ft of contaminated soil below the toe of the retaining wall. The wall stabilization consisted of over 74 inclined drilled and grouted anchor dowels, and 55 tiebacks drilled and grouted to the underlying mica schist bedrock. Three over-lapping rows of jet grout columns were chosen as the foundation solution for the existing retaining wall. This paper focuses on the design, construction and performance of the jet grout curtain wall. The jet grout wall served three purposes: 1) underpinning and excavation support for the removal of contaminated site soils, 2) permanent hydraulic barrier, and 3) resistance against a deep seated failure within the thick clay layer present at the site. The originally designed jet grout wall had unexpected negative effects to the existing retaining wall. The jet grouting program was modified while the Observational Method (Peck 1969) was employed to keep wall movements to a minimum. This paper discusses the diagnostic methods used to determine the cause of retaining wall movement; the implementation of a remedial ground improvement program; the modification to the jet grout installation procedure; and the ultimate performance of the jet grout wall.

Jan 1, 2011

By G. Balletto, C. Furcas

"The mineral raw materials industry is a key-component of the Gross Domestic Product of industrialised economies, closely related to both the building and the industrial sectors. Despite this, at local level mining and quarrying are associated with both irreversible environmental damage and several visual alterations affecting the natural landscape. In this sense, SIA (Social Impact Assessment) has become a strategic tool that can not only improve the prediction but also the assessment of the social impact by involving the local communities in a participatory process. Taking into account the SIA experience, together with the examination of some relevant international case studies, it is possible to draw up a list of good practices for mining project management, from exploration through to closure and beyond, with quarry restoration. Such good practices will complement the existing studies, focusing on environmental issues, with the social issues arisen considered in SIA application."

Jan 1, 2011

By Hiroyuki Tamaru, Futoshi Kusumoto, Kosuke Tanimura, Atsuyuki Kimura

"SUMMARY The Hachinoshiri tunnel is a 2,469 m long two-lane road tunnel on the Chubu-Odan Expressway. Since more than 70% of the total tunnel length consists of low strength rock masses the competence factor of which is less than 1.0, it is expected that a self standing span cannot be achievable because of no ground arch to be established. The tunnel was thus designed with tunnel support patterns forming multi-arc early ring closure that can develop the load-carrying capacity estimated from the exerted earth pressure, Po, which can result from the competence factor, cf. The tunnel support pattern was selected based on the competence factor at tunnel face, then the subsequent tunnel support patterns were determined with reference to the monitoring data. The tunnel construction adopted full-face excavation accompanied by early ring closure using a 330 kW road header. The proposed construction methods at this tunnel site have turned out ensuring tunnelling in massive squeezing rock, so that they can be verified as reasonable tunnelling technologies, clarifying the relationship between the characteristics of the mechanical behaviour of the tunnel and its design parameters. INTRODUCTION The presence of highly weathered mudstone having the competence factor less than 1.0 where the tunnel became unstable with the early ring closure having the distance to early ring closure, Lf, of 6 meters, resulting in difficulty in maintaining the inner section of the tunnel, prompted a substantial amount of high strength double support and replacing of the tunnel support (Sato et al., 2015). Based on the mechanical characteristics learned from the construction, the mechanical stability of multi-arc tunnels was investigated using 3D FDM analyses with respect to the ratio of the radius for early ring closure, r3/r1, and the distance to early ring closure, Lf, so that tunnel support patterns for early ring closure can be established in terms of the competence factor, of, which was employed for a 725 m long section. Consequently the tunnel support patterns for early ring closure which can be determined from the competence factor became applicable to tunnel construction. The relationship between the characteristics of the mechanical behaviour of the tunnel and its mechanical parameters was also clarified. The early ring closure method adopted ensured tunnelling in massive squeezing rock, verifying its effectiveness in stabilizing the tunnel."

Jan 1, 2016

By Hunter W. H, Wilson I. P, Craig R. W

In September 1988 the Imperial Smelting zinc - lead blast furnace at Avonmouth England, was uprated from its then 52 week annual rated capacity of 90 000 tonnes/year of furnace zinc to 110 000 tonnes. In order to provide sufficient extra feed the sinter plant was likewise uprated in April 1989 by increasing the blowing rate of the sinter/acid plants from 100 000 to 120 000 Nm3/h, effectively a 20 per cent increase. In the 12 months after the uprate zinc production was only 85 000 tonnes. Two years after the uprate zinc production had increased to 100 000 tonnes, but it was not until January 1992 that a rolling 12-month zinc production of 110 000 tonnes was consistently achieved. This paper describes the problems encountered with the uprate and how they have been or are being overcome. It deals chronologically with events starting with the restart of the ISF at the end of 1988 and covers the following issues and their resolution: 1. Initial shortages of sinter due to an offset in uprate timing. 2. Greater difficulties in operating the larger furnace particularly on start-up, the greater tendency for iron production and serious slagging problems. 3. Coincidental timing of deleterious trends in slag chemistry. 4. Refractory problems in the furnace shaft and condenser. 5. Shortages of sinter due to commissioning problems with the wet gas and sinter tip end fans, and difficulties in obtaining sufficient sinter hardness. 6. Unrealised full benefits of the sinter-acid uprate due to a late change in design to dispense with sinter gas recirculation, but offset by successful use of oxygen. In a planned maintenance stop in September 1992 further improvements to the furnace design were carried out to resolve the refractory problems, and with improvements to the sinter plant the furnace zinc output capacity is planned to rise to a rate of 120 000 tonnes/year within two years.

Jan 1, 1993

By Raffaella Granata, Wesley Schmutzler, Matteo Bertoni

"The Lower Wood River Levee system, at the confluence of the Wood River Creek and the Mississippi River, in East Alton, Illinois, has been plagued with underground seepage and, in 2010, remediation was deemed necessary by the Southwestern Illinois Flood Prevention District Council and the United States Army Corp of Engineers (USACE). The experts enlisted by the council produced a design that provided for constructing a cutoff wall approximately 2,000 feet long and up to 140 feet deep, through alluvial and outwash soils, and embedded in bedrock. This paper will describe the challenges faced by the Quality Control (QC) and Quality Assurance (QA) teams due to the complex nature of the project in conjunction with an extremely thorough QC/QA program.INTRODUCTIONThe “American Bottom” is an area of 453 km2 (175 square miles) in Southwestern Illinois, extending from Alton south to the Kaskaskia River, which is home to 156,000 people. In the 1940s and 1950s the U.S. Army Corp of Engineers (USACE) designed and built a 120 kilometer (74 mile) long levee system to protect the area from a 500-year flood event on the Mississippi River, which flows through it. The levee system has been plagued by under-seepage for several years. The phenomenon has worsened to varying degrees, depending on location, to the point that remediation was needed.The Southwestern Illinois Flood Prevention District Council (SIFPDC), to obtain Federal Emergency Management accreditation, in June 2010 commissioned a team lead by Amec Foster Wheeler for the design and management of the required levee improvements. The team presented in 2011 the project’s first set of drawings showing proposed design features throughout the levee system. The project was subdivided in four areas, based on the controlling levee districts, one of which, the Wood River Drainage and Levee District, was split into three subdivisions: Upper Wood River, East-West Forks of Wood River, and Lower Wood River.The project included the installation of a cutoff wall at the confluence of the Wood River and the Mississippi River in East Alton, IL (Fig. 1). The Engineer of Record (Amec Foster Wheeler) considered the cutoff wall as the only viable solution to stop the severe under-seepage that was undermining the integrity of the Lower Wood River Levee. The Lower Cutoff Wall (LCW) project is the subject of this paper."

Jan 1, 2017

By D R. Anstey

The growing demand for iron ore from Western Australia has led to an increased focus on the development of magnetite and lower grade iron ore deposits. The need to process and beneficiate the ore from these projects can result in the generation of significant quantities of iron ore tailings over the life of a project. Over the coming decades, the management of iron ore tailings will become a significant aspect of the mining landscape in Western Australia.The tailings generated from iron ore projects differ signifi cantly from other mineral tailings currently produced in Western Australia. Iron ore tailings are generated on a scale not matched by any other mineral process and can often contain asbestiform or potentially acid forming components. New iron ore projects are coming under increased environmental scrutiny because of their large scale operations and the sensitive environments in which they occur. This combination of factors creates some unique challenges for the management of tailings generated by iron ore mining in Western Australia.This paper presents the fi ndings of two studies conducted in recent years to overcome the challenges posed by iron ore tailings. The paper discusses the role of laboratory testing in the development of management strategies for asbestiform minerals in tailings. It also presents a numerical modelling approach for evaluating the rates of rise in the storage of magnetite tailings. The paper concludes by outlining how the findings of these studies can be applied to reduce tailings management costs, lower risks and improve environmental outcomes for the management of tailings from iron ore mining.

Jul 11, 2011

By John A. Herbst

Plantwide control of mineral processing operations has long been sought for its potential benefits. These benefits include minute-to-minute optimization, reacting to disturbances in ore characteristics and equipment status as they happen and the coordination of all unit operations in pursuit of the highest performance level. However several difficult challenges have kept us from fully realizing those benefits. One of these challenges has been to provide fairly complete quantitative descriptions of Unit operations to account for critical interactions within and 'between unit operations. In some cases we understand the physics and chemistry very well and can incorporate that 'knowledge into phenomenological models. In other cases our knowledge is incomplete, so we must rely on other forms of knowledge such as fuzzy logic or neural nets. Another challenge to be met has been to simultaneously compute a large number of manipulated variables. In the past this challenge was met by optimizing only unit-by-unit, rather than on a global basis to significantly reduce the number of variables. In this paper, a procedure that globally optimizes one or two important variables is outlined. This procedure comes much closer to true plantwide optimizing control while remaining computationally feasible. Finally, another major challenge is to choose a meaningful global objective that can be calculated With the models and can be effectively optimized. Financial goals seems to be the objectives of choice. This paper discusses recent progress In overcoming the challenges and illustrates a promising approach which is being pursued at :Mexicana de Cobre's 'La Caridad copper ore concentrator. At M de C, advanced ,control strategies have been 'installed one at a time in the crushing, grinding and flotation sections. During this period, the throughput of La Caridad, Mexico's largest copper concentrator, 'increased from 76;000 tpd to 90,000 tpd. Plantwide integration is expected' to gain an additional 3% improvement in profitability.

Jan 1, 1996

By John A. Herbst, William T. Pate

"Plantwide control of mineral processing operations has long been sought for its potential benefits. These benefits include minute-to-minute optimization, reacting to disturbances in ore characteristics and equipment status as they happen, and the coordination of all unit operations in pursuit of the highest performance level. However, several difficult challenges have kept us from fully realizing those benefits. One of these challenges has been to provide fairly complete quantitative descriptions of unit operations to account for critical interactions within and between unit operations. In some cases we understand the physics and chemistry very well and can incorporate that knowledge into phenomenological models. In other cases our knowledge is incomplete, so we must rely on other forms of knowledge such as fuzzy logic or neural nets. Another challenge to be met has been to simultaneously compute a large number of manipulated variables. In the past this challenge was met by optimizing only unit-by-unit, rather than on a global basis to significaritly reduce the number of variables. In this paper, a procedure that globally optimizes one or two important variables is outlined. This procedure comes much closer to true plantwide optimizing control while remaining computationally feasible. Finally, another major challenge is to choose a meaningful global objective that can be calculated with the models and can be effectively optimized. Financial goals seems to be the objectives of choice.This paper discusses recent progress in overcoming the challenges and illustrates a promising approach which is being pursued at Mexicana de Cobre's La Caridad copper ore concentrator. At M de C, advanced control strategies have been installed one at a time in the crushing, grinding and flotation sections. During this period, the throughput of La Caridad, Mexico's largest copper concentrator, increased from 76,000 tpd to 90,000 tpd. Plantwide integration is expected to gain an additional 3% improvement in profitability."

Jan 1, 1996

By Rainer Hüsken

Over the last decades long BOF campaign lives have successfully been established due to improved quality of the refractory material and due to intensive use of slag splashing. On the other hand, steelmakers are more and more faced with elevated phosphorous contents in the hot metal. This phenomenon is a global tendency caused by the increasing pressure to utilize cheaper iron ore sources. In India, iron ore sources have traditionally elevated phosphorous contents. The phosphorous removal challenge calls for using bottom stirring at the BOF converters, as these combined technology of top oxygen blowing and inert gas stirring through the bottom, helps significantly to improve bath mixing and thus in shifting the process towards the optimum metallurgical equilibrium conditions. All this is common knowledge and daily business in the steelmaking shops all over world. Unfortunately, focusing on a long BOF refractory campaign by means of slag splashing and maintaining optimum conditions for high efficient bottom stirring are naturally conflictive aims. Applying slag splashing causes unavoidable bottom built-up which in turn covers or even blocks the bottom tuyeres. Most of the steelmaking shops today are either operating slag splashing without bottom stirring or bottom stirring without slag splashing. Some are trying slag splashing with bottom stirring but mostly only for a certain short period of the whole campaign. Baoshan Meishan Steel is an integrated steel plant, located in Nanjing (China). The plant is operating two BOF shops (3x 150t and 2x 250t), producing various steel grades. Because of the iron ore source used, the hot metal phosphorous content is rather high with up to 2,000 ppm. In order to achieve low phosphorous contents in the molten steel below 200 ppm, Meishan uses the TBM (Thyssen Bottom Metallurgy) bottom stirring technology in both of their steel plants, successfully applying slag splashing and efficient bottom stirring for campaigns up to 10,000 heats. This paper describes the operation procedures, strategies, and the maintenance concept established at Meishan Steel which is suitable to meet both conflicting targets at the same time.

Jul 30, 2018

By A. Galibois, H. Monette, J. L. Collins

This paper deals with the problem of caving, which occurs in varying degrees in blast holes before loading. It is shown that the distribution of the amount of caving in materials may be described by a gamma density function. A decision model to determine the optimal depth of over-drilling 'in order to minimize the expected additional cost per hole is described. Two different policies are discussed. In addition, charts which permit the mine operator to realize significant savings have been drawn for different actual situations.

Jan 1, 1971

By A. S. Hall

Significant pyrite often does not dissolve in the Sobek (1978) nitric acid extraction; therefore, the standard conservative approach is to estimate pyrite using sulfur present in the sum of the nitric acid and residual sulfur fractions. Alunite, when present, appears as residual sulfur. Because alunite does not generate acidic effluents, overestimation of AGP can occur if all residual sulfur is assumed to be undigested pyrite. Evaluation of 16 samples from the Florida Canyon Mine revealed that petrographic examination coupled with a modification of the Sobek method to include a 6 hour hot (250°F) 'nitric acid extraction resulted in a more accurate estimation of AGP.

Jan 1, 1999

By Jun Han

Coal has been mined in the Kailuan mining area for more than 130 years. The remaining reserves consist of, in large part, coals that would have been considered economically unminable or technically not feasible by the previous generations. Some of the current operations have to resort to overmining because the lower seams had been extracted in the past. This paper deals with the feasibility and proper layout of mining roadways of overmining carried out in the No. 5 seam of Qianjiaying coal mine of Kailuan mining area using numerical and physical simulation. FLAC2D was used to investigate the characteristics of stress and displacement in the overburden after extraction of the lower seams. It also analyzed the proper layouts of gateroads in the upper seams, i.e. locating them in the stress-relief zone of the gob so that their stability can be easily maintained. In addition, a two-dimensional physical model was constructed for investigation of damages to the upper seams due to mining of the lower seams. Finally, based on the results of investigations, proper gateroads layout was designed and successful extraction was implemented for panel 1357 in the No.5 seam.

Jan 1, 2009