Search Documents

By S. J. Ma

With the very effective depressant and collector developed by China Bluestar Lehigh Engineering Corp (hereinafter referred to as LEHIGH), satisfied results are obtained from laboratorial beneficiation tests on phosphate samples from Karatau, Republic of Kazakhstan by the direct flotation process. In this paper the effect of single factors on performance of flotation is studied and their applicable ranges are proposed. The final test results are described as follows: As the feed contains 23.20 % P2O5, and 3.96% MgO, a phosphate concentrate assaying 29.77%P2O5 and 1.54% MgO is produced, and the P2O5 recovery in concentrate is 88.28%. The beneficiation tests make it possible to simplify existing technology with fine grinding-desliming, followed by reverse & direct flotation system and consequently improve the concentrate grade and recovery for the future beneficiation plant

Jan 1, 2014

By D. J. Lachel, Douglas E. Hansen, Bruce Kennedy

The very high cost of exploration and development for new mines requires that a carefully planned, complete, and technically competent geotechnical evaluation be applied to the ore body and the surrounding rock. The ground conditions must be predetermined sufficiently so that, during the development and exploitation stages, unexpected conditions will be of minor consequence. Ground conditions are a major factor affecting the cost of excavated items such as shafts and inclines. For example, shafts cost less to sink in tight dry ground than in highly pervious ground below the water table, with all other factors being equal. The proper mining methods also is dependent upon the ground conditions. Bad ground for room-and-pillar mining may be ideal for caving methods; whereas, ideal ground for room-and-pillar mining would be extremely difficult for a caving operation. To do a proper engineering design, the parameters of strength, deformability, and permeability must be determined, in addition to the loads that will be applied as a result of the mining activity. The required degree of accuracy for each parameter depends upon the individual case. For example, the strength of massive rock in which openings of small cross-sectional area are to be driven at shallow depths needs to be resolved only within several thousand kilopascals (pounds per square inch). Under such conditions, the rock strength is not likely to be of great economic importance unless the rock is very weak. Large openings at great depths require a much more accurate appraisal of rock strength and deformation characteristics. Ground water conditions are important at any depth. Today, a number of techniques exist for evaluating conditions before opening up the ground for development. These techniques and their applications are described in more detail later in this text. The evaluation of ore body ground conditions should start at an early stage, as soon as the deposit has been proven viable for a mine. Economic geology investigations mainly serve to define the value and limits of the ore deposit. To do this properly, the geology of the site is determined in at least as much detail as is necessary to define the "controls" for the ore body. The ground-condition evaluation must determine the engineering properties of the ore body and the surrounding material. This includes the structural geology as it relates to rock strength; i.e., the frequency, extent, and orientation of discontinuities such as faults, joints, bedding, etc. Ground water conditions also must be determined. It is important that the detailed geology of the site be determined at an early date. Reasonable geotechnical parameters must be established during this time period, so they can be used in mining model studies that include both physical and mathematical models. The ultimate goal bf-the geotechnical evaluation is to predict the ground behavior as the excavations are made and how the ground behavior will affect the safety and economic well-being of the mine. The formulation of a ground-condition evaluation program should be planned carefully to determine the particular geotechnical parameters only in as great a detail as will have a bearing on the mine design. For instance, it is not necessary to make numerous triaxial tests in strong rock when the mining will be conducted within a few meters (feet) of the surface in a regime of gravity loading and an absence of tectonic stresses. Similarly, it is not necessary to invest large amounts of time and effort in the determination of joint strengths if the orientations of the joints are such that the failure could not occur along them. Generally, the determination of ore body ground conditions can be divided into four main steps: 1) The general and structural geology of the site must be determined; this is determined primarily during the economic evaluation. 2) The material behavior characteristics of the deposit and the vicinity must be determined. 3) The ground water hydrology of the deposit and the vicinity must be determined. 4) Miscellaneous ground support considerations must be established. Gross features are defined first, followed by a series of increasingly detailed investigations. Specifically, the geology study should start by utilizing techniques such as remote sensing, topographic map interpretation, geologic mapping, etc. After the gross features, such as major faults, have been delineated, the studies are directed toward defining the more detailed elements of jointing, rock strength, ground water hydrology, and other characteristics. This information is used to formulate an assessment of the strength of the ore body and the surrounding rock. Finally, all of the gathered information is integrated to make an assessment of the rock behavior in relation to the types of openings, the excavation methods, the support requirements, etc., that should be used for the rock conditions that are present. The mine design and the geotechnical assessment should be an iterative process. General conclusions about the rock conditions will dictate a type of mine plan. The specific mine plan then should be modified by specific geotechnical considerations. For example, an initial assessment may conclude that the ore body is strong and that a strong rock unit is present over the ore body. Thus, one definite possibility is to mine the deposit by room-and-pillar methods. However, subsequent investigations may reveal faults through the deposit, requiring relocation of the mine openings so that pillars and other structures are in sound rock. In other words, the final mine plan should be compatible with the geotechnical aspects of the ore body.

Jan 1, 1982

By Misra V. N

Davis tube tests were conducted on a Koolanooka magnetite iron ore sample, supplied by Kingstream Steel Ltd, to determine the optimum grind size, maximum iron recovery and the cleanness of the products from low intensity magnetic separation (LIMS). The ore sample contained 38.6 per cent iron, 37.8 per cent silica, 6.5 per cent magnesia and 0.54 per cent alumina. XRD and microscopic examination showed that the main minerals in the ore were amphibole (42 per cent), magnetite (39 per cent), and quartz (14 per cent). Amphibole, (Mg, Ca, Fe),Si8O22.2(OH), containing 50.3 per cent SiO2, 35 per cent FeO and 11.5 per cent MgO is the main gangue mineral in the ore, and about 30 per cent of the total iron in the ore is contained in the amphibole. Heavy liquid separation tests showed that it is very difficult to separate iron from silica by gravity separation to obtain a high quality iron concentrate. Three grind sizes were initially tested, ie 45, 38 and 20 ¦m. It was found that grinding to 100 per cent -38 ¦m (P80 of 29 ¦m) appeared to be the best option for liberating the magnetite from gangue minerals. The iron recovery to the LIMS magnetic product for the 100 per cent -38 ¦m sample reached 73 per cent and the iron content was 65 per cent. Further test work suggested that the optimum grind size was a Psu of 25 ¦m.

Jan 1, 1999

By A Scott, S Kanchibotla, J Segui

The æMine to MillÆ concept is not new. In fact, it is the underlying objective of every mine. Unfortunately, in many operations the management structure and reporting systems have created independent æbusinessesÆ within the overall mining enterprise. This has created incentives to optimise the performance of each component of the operation rather than the enterprise as a whole. The Mine to Mill Conference organised by The AusIMM in October 1998 documented a number of case studies where run of mine ore was not presented to the mill in the best possible form for subsequent stages of comminution and processing. A number of examples were quoted where modest expenditure in the mine had a very significant impact on downstream process efficiency and hence costs. Examples included:the minimisation of fines in the mining and handling of iron ore; the management of fines in blasting and crushing for a copper heap leach operation; the control of blast damage, mining recovery and dilution in open cut coal operations; and the optimisation of mine fragmentation to increase mill throughput in gold and copper operations. The latter topic has been trialed at a number of mines and is referred to as æMine to MillÆ fragmentation. A number of æMine to MillÆ type investigations have been reported in the literature including Pease et al, Simkus and Dance, Nielsen, Scott et al, Kojovic et al, Kanchibotla et al, Bulow et al and Hawkes from the 1998 Mine to Mill Conference. In addition, a number of studies are in progress or the results have yet to be published. These studies have demonstrated the feasibility of obtaining the data required to characterise the breakage behaviour of ores and to model the impact of changes to blasting practices on process efficiency. Characterising the breakage behaviour of ores is a vital step in the management of fragmentation and comminution in mines. The characteristics of importance to fragmentation fall outside the parameters conventionally required to describe the economic geology of a deposit. æMine to MillÆ optimisation of fragmentation means that the mining engineer needs information from the geologist in order to be able to help the metallurgist. Providing this information requires close interaction between these groups.

Jan 1, 2000

By Steven W. Wilson, Brigitte Lacouture, Nichola A. McKay

"The Aqqaluk deposit is a lead-zinc ore body that lies immediately north of the Main Pit at Teck Cominco’s Red Dog Mine in Alaska. It is scheduled to begin production in 2011 or 2012. A project team was formed in late 2004 to plan and implement an ore characterisation and metallurgical evaluation on the Aqqaluk ore. The main objective of this program was to facilitate the transition from Main Pit to Aqqaluk ore in the Red Dog concentrator. The program will develop a detailed, spatially-oriented characterisation of the Aqqaluk deposit attributes including lithology, ore geochemistry, bulk mineralogy, ore texture, as well as evaluating the metallurgical characteristics of ore hardness, process water geochemistry, bench-scale floatability and mineral liberation in ground feed, concentrate and tails. Developing correlations between the metallurgical response and the ore characterisation data is key to the emerging science of geometallurgy. This on-going program is a technical due diligence study that aims to reduce the risk associated with processing a new ore and to provide predictive information for mining and stockpile preparation.The test work to date has focused on characterising the five ore zones currently identified in the Aqqaluk deposit, namely: Siliceous (sub-divided to High Zn:Fe and Low Zn:Fe), Vein, Median Plate and Baritic ores. It identified a number of challenges associated with surface oxidation, or weathering, of the core samples and outlined a program for future sample collection and storage. Metallurgical testing evaluated ore hardness by a variety of methods. Preliminary floatability studies have been completed and some initial links have been established between the ore characteristics and the flotation response. Soluble mineral weathering products, the relative abundance of pyrite and marcasite and the iron content in the sphalerite grains have all shown a correlation to mineral recovery.As new core is received, both the ore characterisation and the metallurgical testing will be continued with a view to strengthen the existing correlations and develop new links."

Jan 1, 2007

By W. Petruk

A study was undertaken to determine whether interrelations between mineral grains affect ore breakage during grinding, and to establish a correlation between ore breakage and mineral liberation. A base metal ore from the Brunswick No. 12 deposit in New Brunswick was ground for different periods of time in a laboratory ball mill, and both the unbroken ore and the ground products were analysed by image analysis. The results show that the mode of breakage is strongly influenced by the behaviour of pyrite. Similar size distributions were obtained for material from the 15 minute grind in a laboratory ball mill, for the grinding circuit discharge from a commercial mill, and for pyrite grains in the unbroken ore. This similarity indicates that a 15 minute grind breaks poorly bonded pyrite grains along grain boundaries, and represents the limit of easy breakage for the ore. Such a grind liberates both large separate grains of ore minerals and poorly bonded mineral grains that occur in interstices among pyrite. On the other hand the 15 minute grind does not separate moderately bonded mineral grains nor release moderately bonded interstitial minerals from pyrite; a 45 minute grind in a laboratory ball mill is required. It is assumed that, for Brunswick No. 12 ore, a 45 minute grind in a laboratory ball mill is equivalent to regrinding in a commercial mill. Grinding beyond 45 minutes in a laboratory ball mill breaks the ore by fracturing pyrite across grain boundaries and by chipping grain edges. Such intense grinding does not markedly increase sphalerite liberation from Brunswick No. 12 ore, because most of the sphalerite that can be released was liberated at the 45 minute grind. In contrast the intense grinding increases galena liberation because a significant proportion of the galena occurs as minute inclusions in pyrite. These findings show that ore breakage and coincident liberation depend upon size distributions, intergrowths, and mode of occurrence of the minerals in an ore.

Jan 1, 1988

By W. Petruk

A study was performed to determine whether mineral textures affect are breakage during grinding, and to establish a correlation between are breakage and mineral liberation. A base metal are from the Brunswick No. 12 deposit in New Brunswick, Canada was ground for different periods of time in a laboratory ball mill, and both the unbroken are and the ground products were studied by image analysis. Similar size distributions were obtained for material from the 15-minute grind in a laboratory ball mill (K. 0 67 pm), for the grinding circuit discharge from a commercial mill (K. 0 = 59-72 pm), and for pyrite grains in unbroken are (K,. = 74 pm). This similarity indicates that the 1S-minute grind separated weakly adhering pyrite grains along grain boundaries, and represents the limit of easy breakage for the are. At this grind (15 minutes) large discrete are mineral grains and weakly adhering interstitial fillings aIrong pyrite were liberated. On the other hand, the 15-minute grind neither separated rooderately bonded pyrite grains nor released rooderate1y bonded interstitial minerals from pyritei a 45-minute grind (K.. 31 pm) in a laboratory ball mill was required. For Brunswick No. 12 are, a 45-minute grind in a laboratory ball mill (Keo = 31 pm) is equivalent to regrinding in a commercial mill (K ?? Fl:$ 30 pm). Grinding beyond 45 minutes in the laboratory ball mill broke the are by fracturing pyrite across grain boundaries and by Chipping grain edges. Such intense grinding (longer than 45 minutes) did not markedly increase sphalerite liberation. In contrast, the intense grinding increased galena liberation because a significant proportion of the galena occurs as minute inclusions in pyrite. These findings show that ore breakage and coincident liberation depend upon size distributions, intergrowths, and mode of occurrence of the minerals in an ore.

Jan 1, 1988

The use of QemSCAN in providing mineralogical input to detailed ore and product characterization has proved of immense value in recent years. In this paper, a brief review of selected Cu-case studies is presented to demonstrate the versatility of automated, quantitative mineralogy by QemSCAN. This versatility ranges from measurement and analysis strategies through to data processing and presentation. As a rapid diagnostic service, it is common to find that only grain size, the degrees of liberation and/or ore mineral modal mineralogy are of interest. By contrast, the detail afforded by the simultaneous determination of both gangue and ore minerals can alert mineral engineers to fatal flaws and attributes deleterious to processing that are directly a function of silicate and other gangue mineralogy. Examples of the latter effects include the influence of micaceous minerals and acid consuming species, while the former include fluorine minerals, which can provide both processing and environmental challenges.

Jan 1, 2007

By Richard Gertsch, Jack Eloranta, Leslie Gertsch

An ongoing research program is characterizing the ore qualities that most affect mine and mill processing of iron. Current practice uses assays of magnetic iron and silica, but additional qualities are needed for advanced process control. If additional qualities can be measured from core, blastholes, or process samples, they can be modeled and controlled similarly. What qualities, other than assays, hinder or facilitate beneficiation at each processing step, and how can they be measured in the mine/mill ore stream? This paper describes preliminary determinations of the effects of ore chemistry, hardness, blasthole drill performance, fragmentation control, and grindability on mill performance.

Jan 1, 2005

By M. Holuzko, Y. R. Zhang, J. Alexander

The use of dual-energy X-ray transmission (DE-XRT) technology in the mining industry has been developing rapidly in the past decade. In many projects, DE-XRT images are analysed to classify ore and waste in sulphide deposits where the sulphides and non-sulphides have distinct characteristics in density. In the current practice of DE-XRT image processing, every pixel in the image gets classified into two categories, depending on the intensity of the pixel from both low and high energy X-ray response. If the pixel’s intensity is above the threshold curve generated in the high-energy and lowenergy scatter plot, it is classified as “higher density” material, and the remaining pixels are classified as “lower density” material. This paper elaborates on an alternative approach to DE-XRT image processing for in-depth characterisation of samples from a lead-zinc sulphide deposit. The detailed characterisation is achieved by providing density distribution of individual rock using DE-XRT laboratory sorting unit (COMEX) located at the University of British Columbia. Instead of classifying the X-ray images into two different classes from one threshold curve, multiple density classes are created between two threshold curves to generate the density distribution. By manipulating the two threshold curves, we can analyse images of samples obtained at different resolutions of density distribution. If the two threshold curves become infinitely close to each other, it will create a single-threshold scenario similar to the current methods being used in the industry. This method provides the ability to change the threshold curves, hence providing more flexibility on material characterisation based on the needs of the operation. Furthermore, the DE-XRT images from individual rock specimens are compared to the test results from hand-held X-ray fluorescence (XRF) analyser as well as assays of various elements for the same set of samples. The data analysis will provide information regarding ore characteristics and also the theoretical performance of the sensor-based sorting. Keywords: Dual-energy X-ray Transmission (DE-XRT), X-ray fluorescence (XRF), ore characterisation, density distribution

Jan 1, 2020

By P. A. Roberts

A proposal for a modified in situ leaching method for extracting gold from oxidized gold ores using a non-cyanide lixiviant is described. A non-cyanide lixiviant is suggested because of the obvious concerns posed by injecting cyanide-bearing solutions into the subsurface. Oxidized gold ores were chosen as a focus because earlier research on the use of sodium thiosulfate as a lixiviant under anaerobic conditions indicated that the presence of pyrite led to rapid thiosulfate breakdown. A reconnaissance research program involving ore characterization and hydrometallurgical test work on samples from four Australian ore deposits and preliminary reactive transport modeling studies was carried out. This work showed that lixiviant-oxidant combinations of sodium thiosulfate and ferric EDTA and iodide and iodine are both capable of extracting high percentages of accessible gold from the selected samples in bottle roll tests under anaerobic conditions. The ore characterization and reactive transport studies suggested that both physical and chemical methods of permeability enhancement may be required to lift bulk permeability and the availability of gold for dissolution to sufficiently high levels to obtain adequate gold recoveries. Assuming that such methods prove to be both necessary and economically viable, the mining method would no longer be regarded as simple in situ leaching. Therefore, the term ?in-place leaching? has been adopted for the proposed gold extraction system.

Jan 1, 2010

By Wilkins L. G

Ore recovered by North Broken Hill Limited as a result of mining operations at its Broken Hill leases is obtained, at the present scale of working, in the proportions of 80% from the North mine and 20% from the British mine sections, and is composed mainly of a silver bearing, sulphide lead and zinc mineral, in association with the gangue materials mentioned later in the text.The lead-zinc sulphide lode at the North mine is deposited in folds in pre-Cambrian sedimentary schists. These folds pitch north-east at approximately 40° and dip north-west at approximately 60°. In plan the deposit appears as two lenses designated on the mine as the "Southern" and "Northern" ore-bodies.The Southern ore-body yields the main tonnage of crude ore. The sulphide mass here overlies a heavy layer of rhodonite which persists with the pitch of the lode. In the central section of this ore-body the sulphide zone is coarse grained and of high grade with a wide range of minerals in the gangue dilution. Quartz, garnet, ftuorite, rhodonite, and felspar are common, whilst chalcopyrites, pyrites, pyrrhotite and green felspar are often present. The Northern ore-body is dolomitic to siliceous in nature. Crude ore obtained from the British section is predominantly...

Jan 1, 1940

By R. W. Diamond

THREE mills are now operated by the Consolidated Mining & Smelting Co. of Canada, Ltd.: (1) The Sullivan Concentrator, Chapman Camp, B. C. (near Kimberley, B. C.), (2) the, St. Eugene Concentrator, Moyie, B. C., and (3) the. Tadanac (Customs) Concentrator,Trail, B. C. Differential flotation is the only concentration method employed in all three plants. Tables are used for pilot work only. Values in all ores treated are as minerals of some or all of the metals -lead, zinc, gold or silver. Occasional customs ores contain small amounts of copper. Sulfide iron content of ores treated varies from a FIG. 1.-THE SULLIVAN CONCENTRATOR, CHAPMAN CAMP, B. C. (NEAR KIMBERLEY, B. C.). low figure in some ores to 38 per cent. iron in Sullivan ore. Gangue minerals vary considerably. A few customs ores are somewhat oxidized and as a result present difficulties. Flotation equipment and control are similar in the three mills, and the flow sheets at the St. Eugene and Tadanac mills, while much simpler, are modeled after that of the Sullivan Concentrator. In this paper I will not detail treatment nor equipment in any of our plants but will describe special features in, or in connection with, all of them. I will then deal with flotation reagents, describing our use of each of them, particularly where differing from general practice. I will conclude with comments on special subjects related to differential-flotation.

Jan 1, 1927

By G Smart, D Ward, J Grace

Ridgeway Gold Mine is part of Cadia Valley Operations which is wholly owned and managed by Newcrest Mining Limited. It is an underground sublevel cave (SLC) operation mining approximately 5 Mt per annum. Ore control systems at Ridgeway have been designed to deliver gold and copper metal production through focussing on the ore characteristics that impact on mine and mill performance and ultimately metal delivery. This is achieved using data collection and management systems which allow data to be collected digitally with æat captureÆ validation routines. These data form the basis for forecasting and on-going systems analysis which aim to accurately assess local in situ and drawn ore characteristics. Physical attributes of ore such as draw characteristics, brow conditions, visual grade estimates and draw point sampling are routinely recorded. Ore tracking and accounting systems monitor gold and copper grades, copper mineralogy, host lithology and ore sizing. These factors have material impacts on concentrator throughput and metal recovery. Draw point recovered grades are routinely reconciled back to design data to monitor and assess draw performance. Statistical variance controls are also employed to analyse mine and plant performance and guide actions.

Jan 1, 2003

By S. Gering, R. Ruiz, C. H. Calderon-Arteaga, J. Barrios

"Located in the northeast corner of Zacatecas State, Mexico, the Peñasquito operation is comprised of the Peñasco and Chile Colorado (Brecha Azul) deposits. Openpit mining (prestripping) began in 2010 and full production commenced during 2011. The openpit mines feed both a sulfide concentrator (mill) and a heap leach pad. The project is owned by Goldcorp Inc. Peñasquito is a poly metallic deposit with Au, Ag, Zn and Pb being recovered as payable metals.As a consequence of lower grade ores expected with advancing mine life, Peñasquito is facing a declining metal production profile. To maximize returns and asset value, plant modifications, including the addition of a carbon prefloat circuit and a pyrite leach circuit to improve recovery, are currently being undertaken. This carbon prefloat circuit will enable the recovery of precious and base metals from carbonaceous sediments. This material is currently being stockpiled. With the associated increase in complexity in the process circuit, the requirement of the ore control system to accurately predict ore feed characteristics is critical to maximizing metal recovery at the Peñasquito operation. The addition of the carbon prefloat circuit was also a key driver in allowing the Chile Colorado openpit to be developed.These conditions alongside Goldcorp’s drive to increase profitability and maximize net asset value has created challenges. These challenges are numerous and multifaceted. However, the ability to accurately route materials from the ore control system is critical to site success, and some of these challenges have been overcome by the adoption and implementation of a new ore control (OC) technology. Examples of these technological innovations in the ore control program are discussed in this article and include improvements in geomodeling, material routing and reconciliation. Successful implementation of these elements has led to significant improvements in selectivity, performance and data management, while reducing the variance between planning and execution, thus helping to drive overall improvement across the operation."

Jan 7, 2018

By M. W. Osterberg

The Cyprus Pinos Altos mine exploits small high grade Cu-Zn skarns using trackless equipment and a modified room and pillar mining method. The skarns occur around early Laramide diorite and quartz monzonite stocks. Stage I calc-silicates and sphalerite developed in the Pennsylvanian Magdalena Group between diorite and the marble front and were partially incorporated into a diffuse breccia body. Stage II calc-silicates and Cu sulfides formed in the contact zone with quartz monzonite and along NE-SW faults, overprinting stage I rocks and breccia. The result is a geologically complex deposit formed in two distinct pulses.

Jan 1, 1992

By Otis M. Clarke

The Eufaula bauxite-kaolin district in southeastern Alabama is an important source of raw material for the refractory industries in the United States. At the present time, five companies are mining and processing bauxite and kaolin from this district and a sixth company is holding substantial reserves. Mining operations are expanding, but finding new ore reserves is a major problem. The Geological Survey of Alabama sponsored geologic research in the Eufaula district to: (1) investigate the

Jan 1, 1973

By L. J. Buchanan

The relationship between hydrothermal ore deposits and hot spring systems has received intensive study in recent years, particularly as a consequence of interest in the energy potential of geothermal systems. Base and precious metal deposition in surface pools and at shallow depths in modern geothermal systems has been recorded in numerous publications (1, 2, 3) Theoretical studies of hydrothermal fluid flow at depth, connected to surficial hot springs systems, have been presented by White and others (1), Cathles (2) , Henley and McNabb (3). As a result of these and additional studies, numerous hydrothermal ore deposits are thought to have originated as genetic parts of larger geothermal systems. In particular, it appears that metal precipitation is greatly enhanced in zones of boiling where volatiles and steam are escaping (4). High grade, near surface concentrations of base and precious metals, deposited as a result of partial vaporization of rising fluids, are such a common aspect of modern not spring systems that ore deposition models are becoming based on what may be called a geothermal model. In its most general terms, this model requires an anomalously high thermal gradient which acts as the driving force behind a convecting hydrothermal system. The water may be entirely meteoric or may be In part at least of other origins. The water migrates towards the higher temperature area, becomes heated, and picks up alkalies and metals by dissolving minerals along the fluid path. As water exits to the surface above the heat source, a mass balance requires the incoming hot water to rise to replace the lost water. As the water rises past the elevation where the hydrostatic pressure is insufficient to prevent boiling, then boiling will occur. Depending on the salinity and the temperature of the water, boiling can occur anywhere from great depths to near surface. Boiling results in a loss of volatiles, a pH rise in the fluid phase, cooling of the remaining fluid, a rise in oxygen fugacity, a concentration of salts in the remaining liquid, and precipitation of ore and gangue minerals.

Jan 1, 1980

By B. S. Butler

PART I SUMMARY CERTAIN relations between the formation of ore deposits and other geological processes are pretty generally accepted, namely: that many ore deposits are closely associated with igneous activity; that ore deposits accompany certain types of intrusive bodies, notably batholiths and stocks, and that they are concentrated near the tops of such bodies; that igneous activity occurs in belts of strong folding and faulting; that folding and faulting are greatest in basins of extensive sedimentation and least in areas of erosion or slight sedimentation; that areas of erosion or slight sedimentation and of heavy sedimentation persist over long periods and exert a major control over structure, igneous activity, and ore deposition; that cycles of erosion, deposition, folding and faulting, igneous activity, and ore deposition, have been repeated through geologic time resulting in rather definite periods in which metal deposits have formed. In short, ore deposition is but one phase of a series of closely related geological events. It is attempted in this chapter to point out the relations of these interreacting geologic processes to the distribution of ore deposits in the western United States. Three great periods of mineralization are recognized; pre-Cambrian, post-Jurassic, and late Cretaceous-Tertiary. In distribution the deposits of the three periods, with certain exceptions, show a concentration about two large positive areas, the Colorado plateau and the Columbia plateau, which suggests a causal relation. The most general age divisions of the rocks of the Cordilleran region of the United States are (1) pre-Cambrian, and (2) Cambrian and later rocks. The pre-Cambrian rocks are exposed mainly through the Rocky Mountain belt from the Canadian boundary southward to Arizona and westward through Arizona to southern California. They have commonly

Jan 1, 1933

By Daniel R. Shawe

Epigenetic ore deposits in Nevada and Utah occur in clusters or belts in a variety of tectonic settings. Many are concentrated in the western half of Nevada in a region containing numerous, relatively large intrusive bodies. Throughout Nevada and Utah, they tend to be clustered in elongate zones or belts. Some of these belts are well defined by the distribution of mineral deposits, patterns of igneous rocks, alinements of faults, and aeromagnetic anomalies, whereas others are equivocal. The Pioche belt in eastern Nevada and western Utah, the Eureka belt in central Nevada, and the Manhattan belt in western Nevada exemplify the general characteristics of these belts, the close relation of some belts to geologic structure, and the lack of a clear correspondence in other belts. Some of these belts are characterized by alined or en echelon faults that disrupt the north-trending Basin ranges, by belts of Cretaceous and Tertiary granitoid and porphyry intrusive rocks near which the ore deposits occur, and by alined magnetic anomalies generally related to the Cretaceous and Tertiary intrusive rocks. All the mineral belts have produced precious and base metals and tungsten; the Manhattan belt in addition has produced magnesite and brucite; and the Pioche belt, uranium, fluorspar, and alunite. The belts in Nevada and Utah may be related to a variety of factors, such as zones of structural weakness in Precambrian rocks, transverse zones of lateral faulting, localized areas of igneous activity, or a combination of these and other factors. Specific types of ore deposits in Nevada and Utah seem related compositionally to the intrusive bodies with which they are associated. Iron deposits, for example, are associated with mafic intrusive rocks such as diorite or gabbro, whereas copper deposits generally and tungsten deposits almost exclusively are associated with granitic intrusive rocks such as quartz monzonltc and granodiorite.

Jan 1, 1976