Search Documents

By Diana K. Schimmelpfennig

Assessment of revegetation success on mined lands is a difficult, time consuming task and has been the subject of a number of controversies. Present regulations require that both plant cover and aboveground plant biomass be measured for use in making that assessment. Of these two variables, biomass is the most time consuming to measure and requires destructive sampling, a most undesirable requirement on fragile, recently revegetated areas. On the other hand, plant cover can be estimated using the point-frame method which is relatively nondestructive. In addition, vegetation can be sampled more uniformly with the point frame and in less time if species composition measures are to be made. A study was done to evaluate the predictability of aboveground biomass production on revegetated mined sites and adjacent native prairies using plant cover estimates made with the point frame method. The predictability of biomass production by cover estimates bears on the need for both measurements in assessing revegetation success. In general, a positive, statistically, significant correlation was demonstrated between plant cover (estimated by the point frame) and aboveground biomass (estimated by the harvest method) regardless of community type (mined or native), species composition, diversity or level of biomass production. However, the latter did have their effects on the relationship and must be accounted for in any predictive equations (that is to say, the predictive equations must be considered site-specific). Considering the relationship observed between the two parameters, cover estimation may be a sufficient indicator of revegetation success, especially where time and minimization of disturbance are critical.

Jan 1, 1982

By Nunna Malakondaiah

Plant samples collected from the mined sites of Beulah, Center and Zap and the test sites of North Beulah 1, North Beulah If, South Beulahh and Center were analyzed for their nutrient concentrations. The vegetation from the mined areas generally showed lower concentrations of Na, P and Cu and failed to meet the nutritional requirements for beef cattle as defined by National Research Council (minimum requirements are: Na, 600; Cu, 4; P, 1800 µg/g dry weight). Plants from Beulah showed generally higher concentrations than from Center or Tap. Tissue concentrations of K varied significantly between sites for 5 species due to the low tissue concentrations at Center. Deficiencies are difficult to isolate as the sampling was done in mid-summer and generally during that season the tissue concentrations tend to decrease in several species. All of the plant species at the unmined sites, with the exception of western wheatgrass at Zap, had lower concentrations of P than the minimum nutritional requirements for beef cattle. Sodium concentration was low but Cu was marginal to adequate in plant species at the unmined sites. Concentrations of K, Mn and Cu in western wheatgrass were greater at Center than at Zap while the opposite was true of the concentrations of Zn, Cu and P in blue grama and Cu in green needlegrass. Amending the spoil with slack at North Beulah I decreased the concentrations of Zn, Cu and P in wheatgrasses grown on spoil from 0-2, 5-10, and 20-25 foot depths, respectively. In general, the mean tissue K+/Na+ ratios were greater in plants on slack amended spoils, primarily due to the reduced Na concentrations in the tissue. At North Beulah II test site, only wheatgrasses grown on spoil amended with slack showed significant increase in K and decrease in Na and Mn concentrations. At South Beulah test site which received 12" topsoil over graded spoil, leonardite amendment decreased P concentrations in all of the grasses as compared to control, whereas fertilizer treatment increased the same. Nutrient concentrations were lower in both fescue and needlegrass with leonardite treatment and higher with fertilizer treatment although not significantly different from control. The concentrations of Ca, Mg, Na, Fe, Cu and N in grasses grown on topsoil at Center test site were significantly higher than on slack amended spoil. Legumes grown on topsoil at Center site contained higher concentrations of P than those grown on spoil; there were no significant effects due to slack on spoil or topsoil. The data presented in this report act only as an indication of between-treatment and between-species differences in tissue composition of plants harvested in mid-summer season. With respect to the nutrients analyzed, since none were found to be toxic, the cattle can safely feed on the vegetation of these mined areas.

Jan 1, 1982

By Thomas L. Starks

Surface soil/spoil Samples (0-10 cm) from experimental test sites in western North Dakota were aseptically collected during August 1975 and each month (May through September) during 1076 and 1977. Selected samples were Cultured in a defined inorganic medium and after six weeks the algae were identified. Chlorophyll u content of the soil/spoil was used as a measure of the algal abundance. Soil physical-chemical properties, species variety and abundance were statistically analyzed. All test sites revealed distinct soil algal communities and demonstrated a successional trend as evidenced by significant increase, in species variety and bionmass over time. Some soil factors, calcium, copper, and phosphorus affected species variety and abundance at more than one situ. Others were important at specific sites; silicon and aluminum at the South Beulah test site; manganese sodium and zinc at the North Beulah test site No. 1 and boron, cadmium and magnesium at the North Beulah test site No. 2. Topsoiled areas had higher species varieties and abundances when compared with control areas, as did plots treated with amendments such as leonardite and fertilizer Generally.

Jan 1, 1982

By Louis R. Iverson

Analysis of seed numbers present in topsoils (a grazed area, an ungrazed area, and two stockpiles) indicated that seeds of the most prevalent colonizers (e.g., Kochia scoparla, Setaria virdis, and Salsolo collins) were not present in the topsoil upon respreading but rather appeared by immigration from the surrounding areas. The grazed site had a seed density of over 7,700 seeds m-2 (of which 43% were from weedy species) and the ungrazed site had 3,900 seeds m-2 (of which 7% were weeds); the stockpiled topsoils had very low seed densities (255 and 520 seeds m-2). Seed densities and diversity decreased with depth on both the grazed and ungrazed sites; this was especially true on the grazed site where 94% of the seeds were found in the surface 7.5 cm. Several species were present in the seed bank (e.g., Hedeoma hispida, Artemesia ludoviciana, A. frigida, and A, abslnthlum) which were also found on the three and four year old mined sites in the aboveground vegetation survey. Seeds from these species may germinate after several years of dormancy, thereby starting populations on mined sites and enhancing plant diversity. Seed bank analysis was also undertaken on mined sites ranging in age of 2 to 6 years (plus an unmined site). Mined site seed densities ranged from 1630 to 3980 seeds m-2, with the four year old site having the greatest density (largely because of high Melilotus spp. populations); unmined site and stockpiled topsoil sample had lower seed densities. A significant positive correlation between total viable seed content and soil-water saturation percentage indicated that soil texture may influence seed viability/ dormancy (the. finer the material, the higher the seed population). As with the previous part of this study (and other studies), there was a poor correlation between the aboveground flora and the belowground seed composition.

Jan 1, 1982

By Stephen E. Stewart

This document presents the explosion-proof enclosures used severity of certification tests solutions to linear transient thermal and stress analyses of in underground mines. The results were used to assess the for enclosure windows relative to possible loads occurring in the actual mine environment. Cast iron electric light enclosures with polycarbonate and glass windows were analyzed under steady state thermal conditions (light burning) and for thermal shocks corresponding to an internal explosion (ignition of volatile mine gas) or external quenching (mine water spray system). Thermal shocks to the enclosure, caused by ignited gases or water spray, were applied via a series of load steps in the transient analysis. The temperature dependence of material I properties and of the film heat transfer coefficients were included in the model. The work demonstrates that thermally induced stresses are strongly influenced by the way the window is mounted in the enclosure. It also shows that the MSHA Thermal Shock Test, if performed on an unsupported lens (or window), produces lower stresses than the lens (or window) may experience in the mine environment.

Jan 1, 1984

The objective of this research was to evaluate the technical and economic constraints on the extraction and utilization of anthracite coal and to determine the research and development needed in order to make anthracite coal more fully utilized as a premium energy resource. In the report the contractor examines in detail the anthracite industry both past and present and evaluates market possibilities. Anthracite reserves and resources are analyzed and tabulated, and the problem of pumping and drainage from the flooded anthracite fields is covered. Current technology is considered in detail with a discussion of production techniques with potential for improvement. The contractor concludes the report with a summary of constraints on the anthracite industry and the contractor's recommendations for effecting a revitalization of that industry. An estimated production of 17 million tons annually by 1990 can be anticipated if adequate planning, research, and development to overcome present constraints are initiated in the near future.

Jan 1, 1975

By William P. Harris

The Lincoln Terminal System is described as a device with the capability to deliver technical information, monitor student performance, and assure learning in industrial training. An experimental unit, the LTS-3S, was constructed and delivered to the Bureau of Mines with appropriate lesson material for a test of feasibility and acceptability of this form of training in the mining environment. Operations were conducted at two mine maintenance schools. The overall results were that (1) there was a substantial improvement between tests before and after self-training on the LTS, (2) students found this an acceptable way to learn, and (3) reaction by training personnel and supervisors was favorable toward the feasibility and advantages of using the LTS in the mining environment. Transfer of the LTS to industry depends on availability of reliable units and adequate lesson material. The requirements for authors of training materials were established based on advice from mine training experts, formal analysis of lesson development procedures, and experience from efforts in lesson development at Lincoln Laboratory-It was concluded that experienced mine training instructors were best qualified to proceed effectively and economically to format instructional material for the LTS, if supported by well-designed facilities and services. Discussion with mining experts confirmed the desirability of generating training materials and delivering instruction at distributed locations to meet local training needs and in direct support of industrial operations.

Jan 1, 1975

By G. G. Huggins

A demonstration project has been completed to reduce the operator sound level of an underground service vehicle, a personnel dispatch wagon, to go dB(A) or less. The program objective was to implement quieting recommendations made on an earlier study for the USBM n diesel-powered mine equipment. The manufacturer and mine to which the vehicle was going actively participated in the program to ensure a product that was not only quiet, but useful. The key element of the quieting package is an engine part a1 enclosure, which, with several complementary noise control components, reduced the operator sound level 14 dB, from 101 dB(A) to 87 dB(A). The vehicle underwent a 4-month trial period, with no degradation in the quieting package. Mine personnel reported no maintenance difficulties, and were enthusiastic about the dispatch.

Jan 1, 1975

By R. V. Petrella

The flash induced combustion of Sewell and Pittsburgh coals was studied in air and in oxygen. The primary decomposition and combustion processes occur within the first 300 ~sec in oxygen and slightly later in air. Strong absorption spectra of CN and OH are indicative of the decomposition and combustion processes, respectively. Kinetic spectroscopy and combustion product analyses indicate that only about 35% of the coal dust is consumed in the explosive combustion which takes place in several (1-5) distinct but similar steps. The combustion-modifying effects of (NH4)2HP04, NH4H2P04, KHC03 and Rock Dust were studied in the 1-20 wt % range in coal dust flash com-busted in air and oxygen. The study reported herein shows Rock Dust to be the most efficient coal combustion inhibitor. KHC03 is the least effective agent, with the phosphate salts showing marginal effectiveness.

Jan 1, 1976

By William G. Pariseau

A brief description of a two-dimensional elastic-plastic finite element program intended for mine stability analysis is presented that includes detailed instruction for input data preparation and how to obtain output.

Jan 1, 1978

By Frank C. Townsend

Waste disposal schemes using spent shale in embankments require a thorough knowledge of its geotechnical engineering properties for environ-mentally safe disposal. In this context, the objective of this laboratory investigation was to determine the physical properties, geotechnical properties, and composition of spent oil shale retorted by the PARAHO and TOSCO processes. Physical properties consisted of mechanical analyses, Atterberg limits, and specific gravity determinations. Geotechnical engineering properties were determined by compaction, maximum-minimum density, unconfined compression, triaxial compression, permeability, direct shear, Ko, cyclic tri-axial, resonant column, and Los Angeles Abrasion tests. Petrographic, chemical, and scanning electron microscopy analyses were used to determine compositional features. Unprocessed shale is hard and durable and more properly described as a carbonate rock instead of shale. PARAHO is classified as a GP, while TOSCO classifies as an SM. PARAHO requires no moisture for compaction to maximum densities; however, TOSCO does. Retorting causes a loss in durability but creates self-cementing characteristics, which for PARAHO a 3-to 8-fold strength increase was observed, while for TOSCO the increase was 1.5 to 3 folds. The shear strength, compressibility, and dynamic properties of compacted PARAHO are comparable to those for sandy gravels. Compacted PARAHO is semipervious, while compacted TOSCO can be semipervious to impermeable.

Jan 1, 1979

By R. F. Kehrman

Voice Frequency (VF) electromagnetic trapped miner location devices were tested for reliability and effectiveness in 93 coal mines. Tests included uplink pulsed CW, downlink pulsed OW and downlink voice evaluations. Frequencies were 630, 1050, 1950 and 3030 Hertz. Overburden depths varied from 70 feet to 1550 feet. Successful communications were established at 91 of the 93 mines. Data indicate the transmitters and receivers will operate in practically all coal mine environments. Reliability and accuracy as location devices appear to depend on noise, depth and presence of metallic objects which distort the magnetic field. In addition, theoretical models appear to define best case situations in terms of noise and conductivity. Minor hardware problems were encountered, mostly involving battery contacts, switches and antenna cables on the receivers. No hardware problems occurred with the transmitters.

Jan 1, 1978

By A. Stawsky

Effective use of diesel vehicles in underground mining requires attention to improved control of diesel exhaust pollutants such as particulate (soot), oxides of nitrogen and sulfur and carbon monoxide. An experimental survey Is made of diesel emission aftertreatment control techniques including water scrubbers, catalytic converters, exhaust gas recirculation (EGR) and soot filters. Use of two or more techniques in combinations are tested for optimum control of all exhaust pollutants. Dynamometer data is developed for steady state and computer controlled simulated mines duty cycles operation of Deutz F6L-714 and F8L-413 engines. Exhaust Quality indices (EQIs) are calculated from dynamometer data for comparisons among the control combinations examined. The Corning diesel particulate filter (DPF) is shown to be the most promising and practical device. The Corning DPF in combination with EGR provided the best (lowest) EQI from the test data. Use of the DPF requires additional regeneration mechanisms such as a catalytic filter coating or fuel additives. A metal mine field test is made of DPFs on an operational scoop tram to test practical applicability. Further development is proposed for application to various mine conditions and for improvement of DPF regeneration techniques including coating with newly available catalysts.

Jan 1, 1987

By Paul S. Goodman

This report examines the effectiveness of bonus plans in the coal industry. The analysis uses theoretical, literature review and empirical approaches to determine the impact of bonus plans on safety and productivity in underground coal mines. The basic finding is that the modal bonus plan in underground coal mining does not have a major impact on productivity and safety indicators. The design of the plan, or organizational factors, and the process of introducing the plan all contribute to its relative ineffectiveness. Strategies and options for designing effective plans are presented.

Jan 1, 1987

By William D. Dodge

A typical quality program plan is presented for explosion-proof (XP) electrical enclosures. The plan is suggested for manufactures of XP enclosures which are to be certified by MSHA for mining use. The plan describes the quality system, organization and implementing mechanisms which are to be applied in the manufacture and delivery of certified XP enclosures. Example forms and example procedures are included.

Jan 1, 1984

By P. A. Cox

Guidelines are provided for the design of explosion-proof electrical enclosures that will meet MSHA certification requirements according to Part 18, Title 30, of the Code of Federal Regulations, and fulfill their intended service underground. The guide covers only those aspects of design which affect enclosure strength, ruggedness, endurance and flame path, i. e., the enclosure ability to properly contain an internal explosion. Internal static and explosion pressures, external impact and thermal heating load are treated as well as the proper selection of materials and welding procedures.

Jan 1, 1985

By Charles H. Parr

A testing program was conducted to determine the suitability and reliability of adhesives and polycarbonate lenses for extended use in luminaires in mine environments. Polycarbonates were exposed, for periods up to 36 months, to four environments including ultraviolet light, humidity, intermittent water spray, and heat of either 180°F or 407 in various combinations. Rod impact tests on the exposed lens material indicated, that polycarbonate functions well under all 180°F environments and could be used with confidence for periods exceeding the test period, for as long as ten years, with a suit) able safety factor employed in design. The specimens exposed at 240°F showed decreased toughness after 24 months' exposure. Extrapolation of these data was deemed to be risky. A 462-day compatibility test between polycarbonate and six hydraulic fluids was run on stressed PC beams. One fluid caused beam breakage in less than one day, while three caused breakage at intermediate times. Two fluids exhibited essentially no effect on the PC when compared to a control. Epoxy and silicone adhesives were tested as lens adhesives and sealants. Three epoxy combinations tested showed low and erratic failure stresses. A room-temperature-cure silicone adhesive functioned extremely well for time periods up to 36 months and temperatures u2 to 240°F.

Jan 1, 1985

By Paul S. Schopf

The results of an experimental investigation into the possible use of medium energy acoustic fields (130 to 140 dB) to precipitate 1 to 10 micron particles is presented. The aerosol was produced with a LeMer generator using oleic acid and nitrogen. The sound field was a sinusoidal standing wave field in an acrylic tube, with light transmission data used for concentration determination. The results showed collection efficiencies of up to 80% on 2 micron particles with a residence time of 11.8 seconds at a sound pressure level of 139 dB re 2x10-5 N/m2. A discussion of the possible turbulent mechanism is made, as well as review and comparison with others? work.

Jan 1, 1972

By Carl R. Christiansen

The primary objectives of this project are (1) the determination of manpower demand in primary lead and zinc production for the years 1985 and 2000, and (2) the estimation of the availability of the required manpower for these years. In order to meet the first of these objectives relationships between employee requirements and metal production in the various states were established, The total primary lead and zinc production from United states mines in 1985 and 2000 has been predicted by the U.S. Bureau of Mines. These forecasts and the 1974 figures are as follows: [1974 1985 2000 Lead metal, tons 669,000 700,000 900,000 Zinc metal, tons 494,000 585,000 995,000] Mining By analysis of ore reserve data and industry characteristics, the authors estimated the portion of the primary production which each state would yield in the future years. As manpower requirements are determined by the tons of ore produced and by worker productivity, these figures were determined for each mining state and district by developing relationships between lead and zinc metal production, ore production, ore to recoverable metal ratios, employee productivity, and number of employees required. The number of new employees required annually to compensate for attrition and production growth is provided, also.

Jan 1, 1975

By Kenneth R. Maser

This report describes a research and development program sponsored by the United State s Bureau of Mines. The purpose of the program was to develop reusable explosion-proof bulkheads for a cross-cut emergency shelter, and to study the implementation of such bulk-heads, and the resulting shelters, as part of an emergency escape plan in a normal coal mining environment. The first part of this report reveals a number of significant conclusions regarding the application of emergency shelters. A study of the cause s of, and the conditions prevailing during a mine emergency indicate s that ideal placement of the shelter s would be midway along developing entries, and at the inter section of butt and main entries. The proper spacing of shelters is based on the travel capability of trapped miners, which is in turn dependent on the height of coal. The life of a given emergency shelter, based on an analysis of the above information, will be anywhere from 6 months to 10 years. Consequently, some shelters are regarded as "temporary?, while others "permanent?.

Jan 1, 1975