Search Documents

By Ricardo Oliveira Gallart de Menezes, Claudio Gerheim Porto, Reiner Neumann

This study presents the results of the mineralogical characterization of Ti-Zr ore from the Jiboia deposit, located in the municipality of Brejo Grande, Sergipe State, Brazil. The goal is to identify the main Ti, Zr, and REE carrier phases in the different particle size fractions in order to subsidize the development of a cost-effective processing route for the production of heavy minerals concentrate. The mineral resources are estimated at 31.5Mt @ 3.5% of total heavy minerals (THM) for the Jiboia Ti-Zr deposit, of which 5 Mt @ 3.39% THM were classified as measured and indicated. The mineralogy of the heavy mineral concentrate recalculated to 100% is represented by 22% pseudorutile, 20% ilmenite, 15% zircon, 5% rutile, 2% monazite, and 36% gangue. The ore minerals are preferably concentrated in the 150 × 53-μm granulometric fractions, which represents 80% of the THM and only 27% of the ROM (Run-of-Mine) ore. Therefore, by cutting the ore to 150 μm, it is possible to discard 73% of the ROM mass and recover 80% of the THM, including 100% of the zircon and monazite which are the most valuable minerals present in the heavy mineral concentrate. The global recovery of THM starts to decline rapidly in the fractions finer than 106 μm and the mass disposal (tailing) does not follow in the same proportion. Higher zircon contents in the concentrates of the fractions finer than 150 μm imply a significantly lower recovery of heavy minerals like ilmenite, pseudorutile, and rutile that make the fractions coarser than 150 μm.

Jan 9, 2024

By S. B. Bortnikova

This paper presents the results of an investigation of the gold-silver oxidized ores at the Salair mine. West Siberia. High losses of precious metals during primary ore processing are the result of outdated technology that is not suited to treat the present ore compositions. The main mineralogical forms of gold and silver and their confinement to different grain size fractions have been determined. About 50% of gold in the slime fraction and 60% of the silver in the form of acanthite that are scattered from the secondary minerals are lost to the waste. The results of these investigations have provided the basis for the recommendation of a new technological process to upgrade the current practice of the gold extraction plant and for methods to reprocess the concentrates.

Jan 1, 1995

By A. Makavetskas

"The purpose of the research is to study the mineralogical features of the structure of the wall accretion formed during melting on the working surface of the walls of metallurgical aggregates and adversely affect the stability of the lining of blast furnaces (BF). We presented the results of studies of the material composition of lining and wall accretion of the furnaces of blast furnaces of the metallurgical plant specializing in the smelting of ferromanganese, nodular and pig iron. It is established that the garnissage is an aggregate of layered texture, formed as a result of the crystallization of slag and metallic melts. Refractory calcium and magnesium silicates and aluminosilicates (minerals of the melilite group, leicite, olivine group minerals) and amorphous glassy oxide solid solutions of variable composition crystallize from the slag melts in the upper part of the hearth. In the slag matrix, inclusions of carbon (amorphous and graphite) and products of crystallization of metallic melts of alpha-iron, iron carbides and / or manganese are observed. Evidence of carbon evolution (in the form of graphite) is precisely in the crystallization of metal melts, there are significant differences in the structure of carbon in coke and in the garnissage. The conducted studies confirm that it is impossible to obtain reliable information on the material composition of new formations in the blast-furnace process without using a complex of modern methods of technological mineralogy.INTRODUCTION The formation of the wall accretion (garnissage) - a solid protective layer as a result of smelting products crystallization on the inner (working) surface of the liner. This is due to the design of blast furnaces with a high-efficiency heat sink using copper coolers and the use of carbon blocks with high thermal conductivity in the lining. The objective of the study was research of the material composition of the lining and wall accretion of the blast furnace hearth of one metallurgical plant that specialized in smelting ferromanganese, nodular and pig iron, to assess the effect of new formations for stability of the lining of blast furnaces (BF)."

Jan 1, 2018

By T. T. Chen

The behavior of gold in a conventional copper electrorefinery anode slimes treatment process is expounded on in this study. In the raw anode slimes generated in a copper electrorefinery, gold occurs mainly as tiny particles of metallic gold, which are commonly attached to selenide particles. Some gold is also present in selenide form. Decopperizing the anode slimes retains much of the metallic gold, but also promotes the incorporation of gold in the structure of silver-rich selenide species. A greater fraction of the gold is converted to (Ag,Au)2Se or Ag3AuSe2 when high-Se and high-Ag anode slimes are decopperized at elevated temperatures and pressures. After pelletization and roasting of the slimes, the gold is converted to a (Ag,Au)-alloy and Ag3AuSe2. Smelting of the roaster products eliminates the selenium and converts the gold to a silver-rich (Ag,Au,Pd)-alloy in the dore metal. In the subsequent silver electrorefining process, gold collects as a gold-rich (Au,Ag,Pd)-alloy in the gold mud. Dore smelting rejects many impurities as a silica slag; minor amounts of gold are present as a (Ag,Au,Pd)-alloy in the silica slag. This gold is recovered by flotation and is recycled to the dore furnace. Gold is identified in both the tellurium caustic leach residue and the parting plant wash water mud as tiny particles of metallic gold. These products are also recycled to the dore furnace to recover their gold values.

Jan 1, 2008

By S Hapugoda, J Manuel, E Donskoi, L Lu

Sinter can constitute up to 80–85 per cent of the total ferrous burden in modern blast furnace ironmaking operations. The mineralogy and microstructure of iron ore sinter play an important role in determining its physical and metallurgical properties. As a result, characterisation of sinter phases is a cost-effective and complementary tool to conventional physical and metallurgical testing of iron ore sinter in evaluating and predicting sinter quality. Over the years, CSIRO has developed a scheme for characterising iron ore sinter that classifies primary sinter phases such as unreacted and partially reacted hematite and magnetite, and secondary phases, including prismatic high-temperature silico-ferrite of calcium and alumina (SFCA), microplaty SFCA (SFCA 1), dense SFCA, secondary hematite and magnetite, glass, larnite (dicalcium silicate; Ca2SiO4) and remnant fluxes. Quantification of these phases has traditionally been carried out by manual point counting under a petrographic microscope; however, new technologies based on automated optical image analysis, quantitative X-ray diffraction and scanning electron microscopy are now available for evaluation. In this study, two sinter samples of varying chemistry were prepared and characterised using both point counting and automated optical image analysis. The implication of the results obtained for the performance of different quantification methods is also assessed.CITATION:Hapugoda, S, Lu, L, Donskoi, E and Manuel, J, 2015. Mineralogical quantification of iron ore sinter, in Proceedings Iron Ore 2015, pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By L. Andrews

Keywords: mineralogy, phase-chemical, chemical-looping combustion, XRD, SEM, EDS, QEMSCAN, PGM, slag, matte, ilmenite Mineralogy, traditionally associated with concentrator studies, is being increasingly applied to problems in pyrometallurgy. Such investigations commonly make use of a number of techniques, and the results are combined for a meaningful interpretation, which can lead to a successful solution. Mineralogical applications are described from pyrometallurgical operations. Examples are given of studies and investigations involving mineralogy in chemical-looping combustion, feed monitoring to platinum-smelting furnaces, and losses to slag in base metal and platinum smelting.

Jan 1, 2011

By L. Andrews

Mineralogy, traditionally associated with concentrator studies, is being increasingly applied to problems in pyrometallurgy. Such investigations commonly make use of a number of techniques, and the results are combined for a meaningful interpretation, which can lead to a successful solution for the problem. Mineralogical techniques are described for various pyrometallurgical operations. Examples are given of studies and investigations involving mineralogy in chemical-looping combustion, feed monitoring to platinum-smelting furnaces, and losses to slag in base metal and platinum smelting.

Jan 1, 2011

By Belcher C. B

The Groote Eylandt manganese ore deposits contain mainly pyrolusite and cryptomelane with lesser amounts of the manganese minerals lithiophorite, todorokite, psilomelane, and nsutite. The major non-manganese minerals which occur are quartz, kaolinite, and goethite.Determination of the mineralogy relies mainly on x-ray diffraction analysis. Quantitative methods for the determination of pymlusite and cryptomelane in Groote Eylandt manganese ores have been developed, A large amount of isomorphous substitution may occur in the manganese minerals and a number of minor and trace element associations have been noted. A correlation has been established between the potassium and cryptomelane contents for a wide range of ore types. Anomalous calcium, magnesium, and sodium values occur in samples containing todorokite, and barium is associated with psilomelane. Groote Eylandt lithiophorite appears to contain negligible amounts of lithium (<O· 05 per cent).A relationship between the H20+ and the Al203, K20, and Fe203 contents has been estahlished indicating that much of the combined water content is due to the presence of kaolinite and goethite, and cap be removed by beneficiation of the ore.

Jan 1, 1975

By T. T. Chen

Canadian Electrolytic Zinc has developed the "cement-stabilization of jarosite residue" Garofix) process to stabilize zinc plant jarosite residues for disposal. The cement-jarosite mixtures cure quickly, have good mechanical strength and low hydraulic permeability; they possess good neutralizing capability and chemical stability. In the jarofix process, Portland cement partly decomposes jarosite to form (SO4MOH)12.nH2O, ferric hydroxide and an alkali sulphate. Approximately 40% of the jarosite reacts in mixtures containing 30% cement. The jarofix product also contains various Ca-Al-Fesilicate-sulphate-hydrate phases and gypsum, which bond the individual particles together imparting mechanical strength and reducing the permeability. Most of the reactions take place in the first few hours of curing. Ammonium jarosite is slightly more reactive than sodium jarosite but releases NH3 gas; water-soluble Zn in the jarosite residue is stabilized in the cement reaction products.

Jan 1, 1996

By J Elsen, R Snellings, K Van Balen

This research concerns the mineralogical study of the physico-chemical reactions taking place at the pozzolan-binder interface. Lime binder/ pozzolan mixtures have been prepared for different natural zeolites. Analcime, phillipsite, chabazite, erionite, mordenite and clinoptilolite were mixed with portlandite and water, after which the progress in the reaction was quantitatively determined by thermogravimetrical analyses from three to 180 days. A first and important step was the thorough characterisation of the raw materials by quantitative X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscope energy- dispersive X-ray (SEM-EDX) measurements of the zeolite minerals, Brunauer-Emmet-Teller (BET) specific surface area measurements, grain-size analyses and cation exchange capacity measurements. Beside these zeolite samples with varying Si/Al ratios, two clinoptilolite samples exchanged to the calcium, potassium and sodium form were studied and the difference in their short- and long-term reactivity was assessed. Also the difference in reactivity between identical clinoptilolite samples ground to different grain sizes, obviously having different specific surface areas, was determined experimentally. The results indicate that the external surface area only influences the short-term reactivity, whereas the cation content has effect on both long- and short-term. Na-exchanged samples combine clearly more portlandite in the first few days, whereas the reaction slows down afterwards compared to K- and Ca-exchanged samples. The early reactivity of the unexchanged zeolite samples could be explained by these two parameters, but their long-term reactivity seemed to be related to their Si/Al ratio. Samples with zeolites rich in Si reacted faster then their Al-rich counterparts.

Jan 1, 2008

By Sylvie Lévesque, Frederic Couët, Laura Pérez-Barnuevo, Cory Hennessey

Determining mineralogical characteristics of samples throughout the iron ore concentration process – from drill core samples up to the concentrate – is critical to process improvement and remediation. However, assessment of mineral proportions, liberation, and texture, although essential, can be time-consuming and costly. Thus, a mineralogical study is often not performed or only restricted to a limited number of samples. New iron ore deposits or new ore zones in active mines will bring new challenges as they are known to be problematic due to their lower grades, complex textures and presence of mineral impurities. In those cases, applied process mineralogy will be necessary to understand and to diagnose potential processing issues. To take full advantage of mineralogical information along the iron ore concentration process, new tools are being developed to provide mineralogical data based on texture, composition and liberation. In an early stage at the mine, the automated identification of drill core textures could provide essential information for the prediction of ore concentrability and grindability. In a later stage, the automated modal tool, combining the knowledge of the iron ore mineralogy of a specific deposit and the results of chemical analyses, can quantify the mineral proportions of the ore; results show good agreement between mineral estimation via chemical analysis and modal analysis using a Mineral Liberation Analyser. A bulk mineralogical analyser allowing semi-quantitative evaluation of the liberation of iron oxides is being validated. The results from the bulk mineralogical analyser will eventually be linked with the mineral proportions issued by the automated modal tool to provide complete mineralogical characteristics of iron ore samples. Ultimately, these mineralogical tools could provide valuable and timely insight for predicting concentrators’ performances or troubleshooting gravity separation processes.

Jan 1, 2016

By S. Banisi, H. R. Iran-Manesh, M. R. Shayestefar, H. Shekarchyan

"Flotation circuit of the Sarcheshmeh copper mine processes 41,000 t/d of ore at 0.9% Cu. Chalcopyrite and chalcocite are the main copper bearing minerals which are concentrated in three stages of roughing, cleaning and recleaning. Due to major changes in the reagent addition regime, make-up balls combination, and throughput to the primary mills an increase of 2.6% (from 87.2% to 89.8%) in the sulfide copper recovery was obtained during a period of six years. In order to investigate a rather large variation of monthly recovery (i.e., from 89.0 to 91.2%) of the plant after implementation of the changes, a study was undertaken to trace mineralogically possible causes of such a behavior. During a five-month period, monthly composite samples of feed and tailings of the flotation circuit were taken. At the first stage, the polished sample preparation method and the mineral counting procedure were optimized through a detailed study. Liberation degrees and types of locking of valuable minerals in both streams were determined in three size intervals of +75, +38 and –38 microns. It was found that for both recovery levels (i.e., 89% and 91.2%), there was no significant difference in the liberation degrees of valuable minerals in the flotation feed; the average liberation degree was 57.1% with a standard deviation of 3.1%. On the other hand, in the case of high recovery level (i.e., 91.2%) there was a reduction of 15% in the amount of free valuable minerals in the tailings stream. The highest reduction was found for the -38 micron size range in particular for chalcocite. It was concluded that compared to the grinding circuit the change in the flotation circuit had the significant effect on the plant recovery increase.INTRODUCTIONThe Sarcheshmeh copper ore body contains 1 billion tonnes averaging 0.90 % copper and 0.03 % molybdenum. It is located southeast of Iran and currently processes 41,000 t/d of ore. The concentrator has been in operation since 1982. Last year, the concentrator produced 130,000 tonnes of copper and 4,000 tonnes of molybednite concentrate. An expansion to the plant which will increase the throughput by 50% is under construction and will be effective in 2003.After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailings constitute the main component of the plant final tailings. A concentrate with an average grade of 30.5% Cu is obtained after cleaning and re-cleaning stages. At the present time, the average sulfide copper recovery of the plant is 89.8% which varies depending on the operating conditions and ore type."

Jan 1, 2003

By L. Evrard, S. Brouwer, E. Bosly, E. Boydens

"A partial desulfurization roasting process has been tested on a typical copper-zinc sulfide concentrate in a Nichols Herreshoff monohearth pilot furnace whereby the su!fµr is partially removed and iron is to a certain degree preferentially oxidized. The phase changes that occur in the particles during selective roasting at 650°C and 800°C over a range of residence times were investigated by the use of chemical analysis, optical microscopy, X-ray diffraction and electron microprobe analyses. The purpose of this work was to get an insight into the mineral assemblages formed by controlled oxidation roasting and to evaluate if this non traditional approach could be afterwards used to recover zinc, copper and iron by a physical separation method. IntroductionThere has been considerable interest over the years in improving extraction and processing procedures for recovering non ferrous metals especially from polymetallic ores containing copper, lead, zinc and iron sulfides with very fine intergrown phases. Complex sulfide ores, which represent considerable reserves and resources in copper, lead and zinc, as well as precious metals and sulfur, are difficult to treat by conventional physical processes, leading to impure concentrates at low metal recovery. Some methods that can be used to treat such ores were described by G. Barbery (1). Various metallurgical routes generally combining pyro- and hydrometallurgical methods have been explored to develop new processes to recover the metals from zinc-bearing sulfidic ores and concentrates (2, 3, 4). The feasibility of partitioning complex sulfide minerals to simpler phases in order to improve selective extraction of mineral constituents has also been investigated (5)."

Jan 1, 1999

By Jiuhua Xu, Yuling Xie, Fenglei Bie, Neng Jiang

"Abstract - The Xiaoqingling Mt. area is one of the most productive gold districts in China. The gold-bearing quartz veins are controlled by a series of east-west shear zones within the Archean Taihua Group, and related to the late Yanshanian (Cretaceous) granite. The major metallic minerals are native gold, electrum, pyrite, galena, chalcopyrite and sphalerite, with gangue minerals dominated by quartz, sericite, ankerite, and calcite. The host rocks are mainly amphibolite, plagioclase gneiss, and migmatites. Principal alteration is sericitization, silicification, pyritization, and carbonization.There are four generations of hydrothermal quartz in altered rocks of gold deposits. The earliest generation of quartz, (Q1), occurs in altered amphibolite gneiss and migmatite, and typically contains fluid inclusions with halite crystals (type A) and two phases, (L+V), of fluid inclusions (type B). The salinities of type A inclusions are 32 wt% to 52 wt%, with dissolution temperatures of halite crystals being from 155°C to 465°C. The second generation of quartz, (Q2), occurs as a fine-grained aggregate associated with sericite, and has small (less than 3 µm) type B inclusions. The third generation of quartz, (Q3), occurs in mylonitic, intensively altered rocks and specially beresite (a type of rock composed of quartz, sericite, and pyrite) near the veins, and contains large amounts of CO2-rich fluid inclusions (type C-fluid inclusions with liquid CO2 and type D-fluid inclusion with high density CO2). The CO2 contents of type C range from 72.6 to 87.4 mol% in gas phases, and 35.7 to 68.3 mol% in liquid phases, based on Laser Raman analysis. The homogenization temperatures of fluid inclusion type A and C are from 215°C to 380°C, and from 210°C to 325°C, respectively. The minimum trapping pressure of fluid inclusions is estimated as 80 MPa to 170 MPa for type A, and from 57 MPa to 190 MPa for type C, which approximate to those of fluid inclusions in vein quartz.The ?18O of quartz are from 10.4‰ to 11.0‰ for Q3 of altered rocks, and from 10.7‰ to 12.8‰ for stage I quartz. The calculated ?18O of fluid inclusions varies from -1.3‰ to 6.0‰. The ?D of fluid inclusions ranges from -67‰ to -59‰ and from -81‰ to -48 ‰, respectively. It is concluded that the water in the hydrothermal fluids both reacting with wallrocks and precipitating orebodies could have been mainly of magmatic and/or metamorphic nature. However, local meteoric water might have been important in late mineralization, because of a distinct oxygen-shift toward the meteoric water. The ?34S values for pyrite of the ores range from -7.1‰ to +7.1‰, with an average of +2.9‰. Those of other sulfides (chalcopyrite, galena, and sphalerite, range from -12.5‰ to 8.3‰. The ratios of lead isotopes for galena of the ores are: 17.06 to 17.31 (206Pb/204Pb), 15.43 to 15.74 (207Pb/204Pb) and 37.58 to 38.45 (208Pb/204Pb). In summary, ore-forming fluids in the Wenyu-Dongchuang gold deposits may have originated from a mantle and/or lower crust source, and ore materials were derived from the Precambrian basement, the Taihua Group."

Jan 1, 1998

By S-L. Weeber

Ash fusion temperature is the temperature at which the mineral matter in coal begins to soften, flow and fuse. It is an important parameter relating to coal utilization. Optimum ash fusion temperatures derived from coal in the Witbank Coalfield region are approximately 1400°C, and higher, although temperatures above1300°C may be deemed acceptable. This study attempted to determine which factors, mineralogical or inorganic-chemical, influence variations in the ash fusion temperatures in certain coals. Coal was sampled from the Number 2 coal seam at opencast and underground workings at New Clydesdale Colliery, Witbank Coalfield, South Africa. The samples represented known low and high ash fusion temperature coal. Analyses performed included proximate analyses, calorific value determination, percentage sulphur, ash fusion temperatures, ash analyses (composition of ash), X-ray diffraction, scanning electron microscopy and petrographic studies. Results show that although a complex relationship exists between ash fusion temperature and the various geological and coal parameters, some positive correlative results were obtained. These indicate a possible relationship between low ash fusion temperatures and i) finer size fractions, ii) an increase in iron content present in the form of pyrite and iii) the form in which pyrite is present, namely cleats. High ash fusion temperatures tend to correlate with i) the absence of pyrite or ii) pyrite present as framboids.

Jan 1, 2000

By Hart G. H

In tectonically disturbed zones within coal seams, decreases in the amount of kaolinite in the cellular structure of inertiniterich coal are accompanied by increasing kaolinite contents in fractures within the coal and/or rocks of immediately overlying horizons. This is due to fracturing of the inertinite microstructure by tectonic disturbance and remobilization and redistribution of free, fine-grained material (kaolinite and/or inertodetrinite.) Ascending waters are believed to transport the kaolinite in suspension, and redeposit it in the fractures and pores in the overlying horizons. This removal of material from the inertinite-rich coal leads to an increase in porosity (higher free gas storage), a presumed reduction in coal strength and an apparent increased proneness to instantaneous outbursts of coal and gas.

Jan 1, 1983

By Sne?ana Devi

Mineralogy is a significant scientific discipline, essential in establishing the nature and the character of raw materials, regardless of whether they are monomineral or polymineral. Mineralogical characterization is very important, because its results give valuable information on features and nature of examined materials. Information's on mineralogical nature of mineral raw materials influence directly the quality assessment of a raw material, and thus the possibility of its use. The possibility of use of mineralogy in different industrial branches confirms constant activity of this scientific discipline. By use of methods within mineralogical analysis (optical microscopy, x-ray diffraction and others) data on mineral raw materials can be obtained as support in mineral raw materials quality assessment. Short description of results of mineralogical analysis of some mineral materials (granodiorite, dolomites, clay, refractory materials, slags and casting powders) in this paper shows the importance of its support to quality assessment and determine the possibilities of their use.

Jan 1, 2009

By Lawrence L. Brown

As part of the Federal effort to help maintain an adequate supply of fertilizer materials, the Bureau of Mines conducted research to characterize complex low-grade Michigan phosphate materials and to devise methods for recovering fertilizer-grade phosphate concentrates. The rock is from middle Precambrian sedimentary formations in the Marquette Range located in the central part of the Upper Peninsula of Michigan. Occurrence of phosphate-bearing sediments in Precambrian rocks is rare. This deposit, containing 12 to 15 pct P2O5 is believed to be the richest Precambrian phosphate deposit in the United States. Petrographic examination showed that the conglomeritic rock contains crystalline apatite both in "black pebbles" and in quartz matrix. Attrition scrubbing and sizing tests showed that there is no tendency for phosphate to concentrate in any of the sized fractions. In beneficiation tests, which included grinding to minus 325 mesh followed by phosphate mineral flotation using a fatty acid-fuel oil collector, a phosphate concentrate was obtained that had a grade of 30 pet P2O5 and a P2O5 recovery of 72 pct. This concentrate should be suitable for fertilizer manufacture.

Jan 1, 1982

By T. T. Chen, W. Petruk

The mineralogy of the feed, concentrates and tailings from the Heath Steele mill in New Brunswick was studied in detail to determine the liberation and recoveries of the major ore minerals, and to characterize the occurrence and distribution of the trace elements. The ore milled during August 1977 contained an average of 4.34 wt % Zn, 1.25 wt % Cu, 1.64 wt % Pb and 90 gr/ton Ag. The main trace elements in the ore are silver, cadmium, indium, cobalt, antimony, bismuth, arsenic, mercury, tin and gold. Silver is carried in solid solution in tetrahedrite-tennantlte, galena, Ag-Sb sulfosalts and Pb-Bi-Sb sulfosalts. Approximately half of the silver is recovered in the lead and copper concentrates and the remainder is lost in the tailings and Zn concentrate. As the major silver-bearing minerals also contain Sb and Bi, recovering silver by ore dressing would involve recovering elements that are troublesome in extraction metallurgy. Cadmium and most of the indium and mercury occur in solid solution in sphalerite and consequently are recovered in the zinc concentrate. Some indium is also recovered in the copper concentrate in a second unidentified indium-bearing mineral. Cobalt and arsenic occur principally in arsenopyrite, cobaltite, a Co-Fe sulfarsenide, pyrite and pyrrhotite, and follow these minerals into the tailings. Recovery of the valuable element cobalt, therefore, would involve recovering the environmentally hazardous element arsenic. Most of the tin and gold report to tailings. The ore was ground to about 80% minus 270 mesh. At this grind, 71 wt % of the sphalerite, 66 wt % of the chalcopyrite and 59 wt % of the galena were liberated. Recoveries of free sphalerite, free chalcopyrite and free galena in the Zn, Cu and Pb concentrates were 85 wt %, 76 wt % and 80 wt %, respectively; recoveries of unliberated sphalerite, unliberated chalcopyrite and unliberated galena in the respective Zn, Cu and Pb concentrates were 48 wt %, 5 wt % and 7 wt %. Some of the unliberated sphalerite and chalcopyrite grains in the tailings are large and would have been liberated at a finer grind.

Jan 1, 1980

By Loughnan FC

There are some thirteen laboratories in Australia in which coal petrological work is carried out on a consistent and routine basis. Applied coal petrological research is conducted by several institutions in different disciplines which can be grouped into four main categories:

Jan 1, 1989