Search Documents

By Walter E. Vanderpool

Three drilled foundations for an elevated water-tank were instrumented, tested and monitored during construction and the first two years in service. One shaft was load tested by the Osterberg method. A void was detected in one shaft by cross-hole sonic logging, pulse-echo logging and concrete coring. The void was instrumented, hydrostatically tested and pressure grouted. The shaft was ?abandoned? and replaced by two smaller shafts with a straddle beam cap. One of the replacement shafts and the cap were instrumented. The strain that appeared in the abandoned shaft, the replacement shaft and the cap were monitored during the remainder of the construction, through the commissioning test and the first two years of service. The results demonstrate the precision and sensitivity of the vibrating wire strain gage.

Jan 1, 2004

By Lawrence Adler

For openings in bedded rocks, analyzed by simple beam theory, it has been shown that roof loads can be shifted from one support to another.' This transfer is effected by controlling the relative deflection of adjacent supports. If this action is used to reduce loads in the props or bolts and increase them in the ribs or pillars, it could be productive of economies averaging 30 pct. Such savings can be realized by: 1) using smaller artifical supports such as props and bolts, and 2) increasing loads in the rib to induce eventual failure for longwall caving. Since the rib is relatively load-insensitive, it provides a natural load sink. However, caution must be used in applying such permissive deflections, for while the supports are being handled properly, the stresses in the roof itself are very sensitive to such manipulations.'

Jan 5, 1960

By Xiaoyan Luo, Congcong Dai, Gaipin Cai, Xin Liu, Lu Zong

To overcome the difficulty of accurately judging the load state of a wet ball mill during the grinding process, a method of mill load identification based on the singular value entropy of the modified ensemble empirical mode decomposition (MEEMD) and a probabilistic neural network (PNN) classifier is proposed. First, the MEEMD algorithm is used to decompose the vibration signals recorded under different load states to obtain the intrinsic mode components, and a correlation coefficient threshold is used to select the sensitive mode components that characterize the state of the original signal. Second, singular value decomposition is used to obtain the singular value entropy. Finally, the load state of the wet ball mill is judged based on the magnitude of the singular value entropy. A characteristic mill load vector is constructed from the singular value entropies of the cylinder vibration signals recorded under different load conditions and is used as the input to a PNN, which then outputs the predicted ball mill load state; in this way, a load state identification model is established. Grinding experiments are presented to verify the effectiveness of the proposed method, showing that the method can accurately identify the load state of a wet ball mill. ()

By Wei Zheng

A pulverized coal fired power plant is being built in Osceola, Arkansas, along the Mississippi River. The subsurface soil conditions consist of a certain amount of very soft clayey silt and clay underlain with a medium dense sand layer and a dense sand layer. The site has been raised four to five feet with fill material consisting of sand and gravel. Consolidation settlement due to the fill is expected to cause negative shaft resistance (downdrag) on the pile foundations. The site is located in a high seismic hazard area - the New Madrid Seismic Zone (NMSZ). The liquefaction analyses indicated that there is a high liquefaction potential in the medium dense sand layer. Load tests are needed to determine the shaft resistance and the end bearing of each soil layer for design purpose. Two types of pile foundations ? augered pressure grouted displacement pile (APGD) and partial augered pressure grouted displacement pile (P-APGD) were considered for this project. Ten pile load tests, including five compression tests and five tension tests, were performed for three different areas. Strain gauges were installed for the compression tests. The APGD and P-APGD piles were installed side by side for comparison. In addition, three additional dynamic tests were performed to supplement the information from the static load tests. Load deflection curves for the compression tests were predicted, and the failure loads were interpreted using four different methods. The shaft resistance and the end bearing were determined from the strain gauge data and were used to back calculate the ultimate capacity. The back-calculated capacities are in good agreement with the predicted failure loads; they were further verified with the tension load test results.

Jan 1, 2007

By A. Mazzucato

This paper presents the experimental results of driving and load tests on an instrumented pile driven into a test pit filled with fine homogeneous sand.

Jan 1, 2010

By Jorj O. Osterberg

Until ten years ago, the largest load tests on drilled shafts (bored piles) were about 3,000 tons (27MN). These tests were made with kentledge (large weights, usually concrete blocks) stacked up as a reaction to the applied downward load of a hydraulic jack. In some cases, the jack load is resisted by a load frame held down by piles or anchors connected to the frame. When the test loads exceed 3,000 tons (27MN), these methods become cumbersome expensive and time consuming. The Osterberg (O-cell) test method does not require any reaction load. It has become the only cost effective method for static load testing of high capacity shafts. Over 650 load tests have been performed with this method, 86 of which were over 3,000 tons (27 MN) and 40 over 5,000 tons (44 MN), and the largest test load was 17,000 tons (150 MN). Tests have been made on sands below the water table, shafts ending in rock sockets, and cemented sands and gravels. Test results and details for selected load tests are discussed.

Jan 1, 2002

By David E. Thompson

This paper describes the full-scale field load testing of three deep foundation units using the Osterberg Load Cell. The load tests were completed on three separate projects, two in Massachusetts and one in New York. The Massachusetts projects involved the load testing of two 18-inch O.D. concrete-filled steel pipe piles over water for railroad bridge reconstruction projects in Revere and Saugus/Lynn. The New York project involved the load testing of a 24-inch diameter drilled shaft socketed into sandstone on land for a building foundation in Rochester. The 18-inch O.D. piles were loaded to failure at jack pressures of 142 to 215 tons. The drilled shaft was loaded to failure at jack pressures of approximately 450 tons. The loading testing procedure is described and the results of the three tests are presented. The advantages and disadvantages of the Osterberg load cell for load testing of deep foundations are discussed.

Jan 1, 1989

By Drew Floyd

Five full-scale pile load tests were performed on pairs of PZ-22 sheet piles installed with a vibratory pile driving hammer. The sheet piling was installed in several locations in soil generally consisting of miscellaneous granular fills overlying soft organic silts, inorganic silt interbedded with sands and gravels, very dense glacial till and shale bedrock. The test program also included the use of tip tell tales to determine what capacity could be attributed to tip resistance and skin friction. During the design phase of the project, it was assumed that the capacity of the sheet piles driven with the vibratory hammer could be correlated with the rate of penetration. The correlation between vertical capacity and rate of penetration would be used as a basis for determination of a driving criteria from driving the production sheet piling. The sheet piling load tests demonstrated that it was not possible to correlate the capacity of sheet piling driven with a vibratory hammer and the rate of penetration. It was also demonstrated that the capacity of the sheet piles was directly related to the density of the soil at or just below the tip. The results also tend to agree with empirical equations provided by Meyerhof (1976).

Jan 1, 1989

By John P. Turner, Steven S. Dapp, Dan A. Brown

"The Goethals Bridge Replacement (GBR) spanning the Arthur Kill Waterway between Elizabeth, NJ and Staten Island, NY is supported on over 200 drilled shaft foundations ranging in diameter from 4.5 ft to 10 ft and socketed into Passaic Formation siltstone. Four drilled shafts, two on each side of the bridge (NJ and NY), were load tested using the bi-directional axial load method. Axial test results demonstrate that RQD, taken by itself, is not necessarily a reliable indicator of side or base resistance. High recovery with low RQD can be a function of horizontally bedded siltstone and shale where the individual pieces of core do not exceed four inches, but may still provide very high side and base resistance. Axial testing was followed by a lateral rapid-load test (Statnamic) on each of the same four shafts. In addition, one of the shafts was subjected to a static lateral load test to validate the rapid-load method as being representative of static loading conditions. Results of the axial load tests provide the basis of unit side and unit base resistances used in the LRFD design of the rock sockets for axial loading, while results of the static and Statnamic lateral load tests were used to calibrate p-y curve parameters used for design under lateral and moment loading. This paper describes implementation of the load testing program and its role in the design process.INTRODUCTIONDesign of drilled shaft foundations for the Goethals Bridge Replacement (GBR) required load testing in order to validate the parameters used for calculating geotechnical axial and lateral resistances. The bridge, including foundations, was designed in accordance with the AASHTO LRFD design specifications, 6th Edition (2012). The bridge owner is the Port Authority of New York and New Jersey (PANYNJ). One of the PANYNJ project requirements was stated as follows:“Perform a minimum of two (2) separate axial compression load tests (one [1] in New York and one [1] in New Jersey) for each demonstration shaft of different size and construction methodology to verify the design assumptions and construction procedures. At a minimum, one (1) demonstration shaft is required to be representative of production shafts with a diameter within one (1) foot above or below the demonstration shaft diameter.Conduct a minimum of two (2) lateral load tests (one [1] in New York and one [1] in New Jersey) for each demonstration shaft of different size and construction methodology. At a minimum, one (1) demonstration shaft is required to be representative of production shafts with a diameter within one (1) foot above or below the demonstration shaft diameter.”"

Jan 1, 2016

By Rolf Katzenbach

Construction of drilled shaft foundations with the use of hydraulic oscillators and rotators to install temporary casing over the full depth of the shaft is described. The equipment and techniques were developed in the 1960?s in Germany and full-depth casing is now the predominant method of construction in Europe. Its use in North America is increasing. This paper presents an overview of full-depth casing methods and a summary of available load test data evaluated by the authors to compare the load transfer and capacity performance of shafts installed by various construction methods. Results demonstrate that load transfer and capacity of full-depth casing shafts are equal to or exceed that of shafts constructed by dry or slurry methods and that measured capacities are consistent with generally accepted design equations. The principal advantage of full-depth casing methods over other installation techniques is that the risk of defects in the shaft is minimized. Casing is able to penetrate into the ground under any geologic or groundwater condition when this technique is applied. Potential delays and cost overruns can thus be avoided and a safe, economical foundation element is created.

Jan 1, 2007

By Jogeshwar P. Singh, Aser I. Abbas, Mohamed Ashour

The presented methodology predicts the pile head response (i.e. pile head load - displacement curve) and develops the load transfer (t-z) curve of piles in sandy soils under tension forces based on soil/pile properties and soil-pile interaction. The proposed approach improves the prediction of the t-z curve in sandy soils compared to current practice. The method employs a nonlinear soil constitutive model to calculate the mobilized shear stress/strain in soil at the soil-pile interface induced by pile upward displacement. The approach accounts for the influence of the pile slenderness ratio on the predicted t-z curve and is validated through comparisons with measured pile head response and t-z curves from full-scale pile load tests. INTRODUCTION Piles may be subjected to axial uplift forces due to either static loading or cyclic loading. The majority of methods are only concerned with the pile ultimate tensile capacity. However, the mobilized pile stiffness (i.e., pile-head load-displacement relationship) is essential to determine the interaction between the foundation and the superstructure and consequently the performance of the whole structure. Methods that assess the pile ultimate tensile capacity usually assume the failure surface at the soil-pile interface and estimate the local side shear resistance using a lateral earth pressure approach. The Naval Facilities Engineering Command (NAVFAC 1986) and the US Army Corps of Engineers (USACE 1991) employed Eq. 1 to assess the ultimate shear stress (τ) developed at the soil-pile interface.

Jan 1, 2018

By Mark K. Larson

Calibration of LaModel for deep coal mines begins with adjustment of overburden stiffness for load transfer distance. This calibration determines whether mining induced stresses are concentrated in the immediate abutment of the gob, or spread over a wider area. In the absence of site information, an empirically-based estimate is often used. Where data is available, a recommended calibration procedure can be followed, as is done in this case study at a deep western longwall mine, with minor modifications and extensions. In this case, data sources included borehole pressure cells, flatjacks installed in series with support Cans, and observed changes in ground conditions. Calibration was based on the first detection of mining-induced stress from the advancing longwall. Detection was found to depend on the type and sensitivity of measurement. Borehole pressure cell data with a 20-psi-increase detection threshold were chosen as the standard, in accord with data used in deriving empirical relationships. Application of this standard produced a load transfer distance estimate roughly four times the empirical relationship developed by Peng and Chiang (1984). This is a significant deviation with important implications for panel design at this site. Data from flatjacks, ground condition observations, and borehole pressure cells with higher threshold values, were tightly clustered and show load transfer distances from two to four times empirical guidance. Ratios between various measurements can be used to adjust measurements to the standard (although they may depend on mine geology). Once established, ratios can be used to adjust estimates, say from support flatjacks or ground observations, to the standard, where borehole pressure cell data is not available.`

Jan 1, 2012

By Mark K. Larson, Douglas R. Tesarik, Heather E. Lawson

"Load transfer distance (LTD) is simple in concept and usually evident in underground coal mines. Many people in the mining industry recognize LTD as the distance from the panel to where the mine ribs and pillars show evidence of renewed spalling, floor heave, or other effects of increased weight due to longwall mining or pillaring. Barrier pillars, in particular, are designed to shield mains and other relatively permanent facilities from this loading. LTD is also important in determining the extent and degree to which mining increases the load on pillars and ribs in the gate roads. Generally, a long LTD reduces loads in gate roads, but may require larger barrier pillar widths to protect mains or adjacent panels from excessive loads. Therefore, a long LTD may make it easy or difficult to meet various objectives of mine layout design . LTD reflects overburden geology in two ways: First, overburden that is weak and readily caves will limit both the amount and distance of load transfer. Second, stronger, stiffer, sandier, and more massive overburden increases both the amount and distance of load transfer. As such, LTD is central to coal mine layout design and calibration of numerical models that seek to anticipate these transfers of load during mining. However, the term does not have a consistent definition in the literature, and various instruments and observational techniques with varying sensitivities and thresholds have been used to indicate the onset of mining-induced stress increase and, subsequently, to determine an LTD. Consistency is important for meaningful comparison of ground response between mining sites and for accurate calibration of models.This paper adds to the body of observed and reported LTDs by presenting cases with relatively sandy and massive overburden at two western coal mines. These two cases include observation and measurement of LTD with multiple methods and provide insight into how distances reported relative to different criteria and instrumentation could be adjusted for comparison against a common base. This base is the criteria used by Peng and Chiang (1984) to determine their empirical equation. In one of these two cases, LTD was recently measured at a western U.S. coal mine (Mine A) to be approximately four times that calculated using the Peng and Chiang empirical equation. LTD measurements were examined using various instruments at Mine A and at adjacent Mine B. The measurements at Mine B showed that LTD was significantly greater than that calculated by the Peng and Chiang equation. Difficulties with BPC installation and fittings at Mine B permitted only ranges of LTD to be determined from some BPCs. Even so, the LTDs and ranges of LTDs determined were consistent with the LTDs determined at Mine A."

Jan 1, 2015

By M. W. Fabjanczyk

Cement and resin encapsulated tendons are widely used in the stabilisation of mine roadways. One of the main factors in controlling the efficiency of the reinforcement is the ability of the tendon to generate load in response to rock deformation. The analysis of field data from instrumented reinforcing tendons complimented with extensive laboratory investigations have more accurately defined the mechanisms by which load generation occurs. The role of reinforcing tendon profiles, hole geometry and encapsulation medium properties in controlling the reinforcement stiffness and capacity are discussed. The results of the investigation have implications in both the design of rock reinforcing systems and the optimisation of encapsulation mediums and tendons.

Jan 1, 1992

By Joshua Calnan, Braden Lusk, Kyle Perry

This paper presents detailed information and data regarding the load transfer characteristics of Blast Resistant Glazing Systems utilizing two different thicknesses of polycarbonate. A series of triaxial load cells, along with surrogates of identical stiffness characteristics, were placed around the glazing perimeter to directly measure the load transferred to the support system from explosions of varying degrees. The blast loads were developed using an explosive driven shock tube administered by the University of Kentucky Explosives Research Team (UKERT) in Georgetown, KY. Results presented include distribution of loading, maximum load transferred to connections, blast pressure-time data, glazing system deflection-time data, and final performance results of each system. The two glazing systems respond differently to the applied blast loading. Differences and similarities in the load transfer characteristics are discussed. The experimental results are then compared to a commonly used blast resistant glazing system analysis software tool utilizing a Single Degree of Freedom (SDOF) method of analysis for each system. Preliminary results show that currently used models do not correspond well with experimental data.

Jan 1, 2014

By Randy R. Williams, Brian W. Wilson, George M. Filz, Marina S. W. Li

"Detailed design of an extensive deep mixing (DM) scheme using the Cutter Soil Mixing (CSM) technique was completed for foundation support of mechanically stabilized earth (MSE) walls for Kitimat Liquefied Natural Gas (LNG) at Bish Cove, British Columbia, Canada. The design was based on the provision of soil-cement structures, constructed in highly variable subsurface conditions that consisted of thick deposits of fine-grained soils overlying granular soils, and required to meet project-specific performance criteria, to support the MSE walls. The design, consisting of rectangular CSM panels constructed to form barrettes connecting to a longitudinal wall of continuous CSM panels, was configured to manage the distribution of stresses and strains that could be developed within the soil-cement structure.The results from 2D finite element analyses were used to determine the necessary arrangement and properties of the CSM panels to accommodate localized areas of relatively high shear, tensile and compressive stresses within the soil-cement structure. The relationships between unconfined compressive strength and elastic modulus for fine-grained and granular soil-cement structures obtained from the Bish Cove data were compared with published references and were found to be significantly different in the higher strength range materials.BACKGROUNDDeep Mixing design was completed for the development of the Kitimat LNG Facility located in Bish Cove, British Columbia, for support of two relatively high MSE walls and associated bulk earthwork operations. Deep mixing was necessary to treat the very weak native deposits in-situ to meet project performance requirements and physical constraints without the need for significant excavation and disposal work. The DM design was undertaken on the basis of adoption of the CSM technique for in-situ ground improvement of the native foundation soils which consisted of very soft to soft fine-grained marine deposits and loose to compact sandy silt to silty sand, overlying dense sand and gravel (Fig. 1). The DM area is located immediately upslope of the Bish Cove beach area, and is “L” shaped in plan, approximately 300 m long by approximately 28.8 m wide (parallel to the beach area) and 165 m long by an average width of 21.0 m (perpendicular to the beach area). The depth of the DM ranged from about 5.0 m to 30.7 m with typically 2.0 m embedment into dense granular soils. Details of the design philosophy, including an overview of the DM design and the project background information are presented by Li et al. (2014a). Details of the construction aspects of the Kitimat LNG deep mixing are presented by Wilson et al. (2014)."

Jan 1, 2015

By Robert M. Stevens, Arnoldo Acuña

INTRODUCTION In the early 1950s, underground miners and tunnel¬ing contractors were experimenting with ways to supple¬ment or eliminate track-bound loading and hauling equipment. Diesel-powered crawler and rubber-tire mounted front-end loaders and trucks designed for use on the surface were being modified and tried with limited but encouraging success. Miners began working with interested manufacturers to explore the develop¬ment of vehicles specifically designed to meet the de¬mands and constraints of underground material han¬dling. By the mid 1960s, load-haul-dump (LHD) vehicles were firmly established as a fundamental part of what has become known as the "trackless" mining concept, used in many mines and many countries around the world. The flexibility, mobility, and versatility of these units have given the industry a useful tool and have added new dimensions to mine development and produc¬tion. Many old mines have been redesigned to accom¬modate these trackless vehicles, and few new mining plans have failed to find some use for the concept during some phase of development and production. By 1977, several manufacturers in several different countries were producing a variety of LHD vehicles to meet the growing worldwide demand. GENERAL DESCRIPTION LHD vehicles combine certain characteristics of conventional front-end loaders and dump trucks, spe¬cifically designed for materials handling in underground mining and tunneling. The design intent is to provide one vehicle with one man, with the vehicle loading itself, hauling the load over level or inclined haulageways, and dumping the load. A typical production cycle of the most popular units has the operator driving the vehicle forward, forcing the bucket into the muck at or near floor level, and using the tractive effort of the vehicle and the prying action of the bucket to roll out and tilt back the load as shown in Fig. 1. With the bucket rolled back into the carrying position on the boom and the boom resting on the main frame of the vehicle, the load is hauled (trammed) to the dump point as shown in Fig. 2. At the dump point, the boom is raised, the bucket is rolled forward, and the load slides out as shown in Fig. 3. After dumping, the bucket is rolled back to the carrying position, the boom is returned to rest on the main frame, and the unit is driven back to the loading point for another load. There are two other types of LHD units that are slightly different in the cycles that they perform. One uses a hopper arrangement carried on the front of the machine, with a small bucket mounted ahead of the hopper. Several passes with the small bucket load the hopper, which is dumped by opening its floor. Al¬though this concept is several years old, it has gained less than 0.5% of the total market. The most recent LHD concept differs in that it has one bucket nesting inside another. The smaller inner bucket is loaded first, and it is then tilted back and above the larger bucket. When the larger bucket has been loaded, it is rolled back, and the total load is trammed to the dumping point. The dumping operation tilts the buckets in the reverse order from that of the loading operation. The impact of this new concept on the mining industry has not been measured yet. This chapter concentrates on the LHD vehicles employing the cycle described by Figs. 1 through 3, since these LHD units constitute an estimated 99% of the units in current use. MAIN VEHICLE FEATURES In general, the LHD vehicles available from most manufacturers share the same basic features.

Jan 1, 1982

By Thomas Fraser, David R. Mitchell

THE primary purpose of the loading plant is to transfer the finished product from the preparation machines to the railroad car, truck, or barge in which it is to go to market. Secondary purposes of the loading plant are: to prevent excessive degradation of sizes during loading, to reduce segregation as much as possible, and to prevent excessive quantities of very good or off-grade coal from entering any one car. Nonuniformity of consignments is one of the chief sources of com- plaints by consumers and coal merchants. A properly designed loading plant will do much to reduce complaints and ensure uniformity, not only from shipment to shipment but also in each individual consignment along the length of the car and in cross section. DEGRADATION IN STORAGE, LOADING AND SHIPMENT The object in loading is not only to handle the coal without breakage and segregation, but also to produce a well-trimmed load that will ride to its destination without spillage or breakage en route. The small sizes present in a car of prepared coal as received by the purchaser consist-of: missed small sizes not screened out in the preparation plant, breakage during loading, and breakage caused by handling en route. For domestic sizes of anthracite shipped from the Pennsylvania anthracite field to Atlantic coast cities, the dealers' lass because of breakage in loading and shipment amounts to from 2 to 5 per cent and for anthracite shipped to Middle West cities, the loss is 8 to 9 per cent. This difference is in part because dealers in the Middle West rescreen their coal more thoroughly than is usual in the East. One dealer handling Illinois No. 6 coal shipped from southern Illinois mines to Chicago reports an average size loss of 10 per cent when lump coal is unloaded with a fork. This runs as low as 5 per cent for carefully loaded coal and as high as 15 per cent for carelessly loaded coal.

Jan 1, 1943

By M. M. D. S. Vemba

Paper written on project work carried out in partial fulfilment of B.Sc. Eng (Mining Engineering) degree Engineering refers to the application of mathematics and other sciences to logically develop solutions to problems. However, in opencast mining, due to the randomness of operations, the use of mathematics is often neglected. Instead, practices that have proven successful elsewhere tend to apply. At the other end of the scale, mathematical models have been developed to identify and quantify all the operational parameters involved in the loading and haulage of ore. These are then used to optimize the operation. Optimization in this context, refers to the reduction of cost through effective utilization of the available time and resources. Considering these mathematical models, the loading and transport system at SMC (Catoca Mining Society) will be assessed with a view to its optimization. The discussion will be introduced by considering the mine background and other general information, which will highlight the main operational variables.

Jan 1, 2004

By R. K. Mensah-Biney, M. T. Hepworth, K. J. Reid

The loading characteristics of gold-bromide species onto activated carbon were evaluated using a batch system. The overall loading of gold onto activated carbon was rapid for the first few hours, but it continued without cessation as a result of the reduction of gold. Therefore, conventional equilibrium considerations were not applicable. Although loading continued slowly after several days, an abnormally high, loading capacity value of 10-12 meq/g carbon (650-800 kg Au/t) could be attained in 72 hours. The loading of gold-bromo species by activated carbon was by the mass transfer of (AuBr4)- species to the external surface to be reduced to metallic gold by carbon. Elution of gold from loaded carbon was feasible provided the carbon had not been loaded to high capacity values. If loading is carried to high levels, complete elution becomes impractical, and the gold may be recovered by ashing the carbon. For the high loading capacities observed, this option would appear to be cost effective. The effect of several variables on the loading capacity of the activated carbon for gold-bromo species is discussed.

Jan 1, 1994