Search Documents

By Krogerus. H., P. Jokinen, T. Lintumaa

Keywords: Pyrometallurgy, furnace, coke, smelting charge, optimization, ferrochrome The main consumer of ferrochrome is stainless steel production. Stainless steel must maintain a reasonable price against other competitive materials. Therefore, the ferrochrome price must be low enough and profitable for the producers of stainless steel. The investment and operational costs of ferrochrome production are greatly dependent on the availability of the process and the production rate. Thus the furnace size and production rate in submerged electric arc furnaces will be greatly increased in the near future. The ferrochrome production per furnace, e.g. at Outokumpu?s Tornio Works, increased from 30 000 t/a to 165 000 t/a in about 35 years. The same trend will continue globally but now much more quickly. The Outokumpu ferrochrome process at Tornio Works uses sintered chromite pellets and upgraded lumpy ore as a chromite source. Metallurgical coke is used as a reductant. Reliable smelting in a large furnace demands the correct charge composition and well-known characteristics of the charge components. The quality and electrical conductivity of cokes (normally used) has the most important role for the electrical conductivity of the smelting charge. The results of the measured electrical conductivity of different cokes and the smelting charge with many controlling factors are presented here. These measurements were performed over the years for our own purposes at the laboratory of Outokumpu Research Oy (ORC), in Pori, Finland.

Jan 1, 2006

By Tomohiro Yamasaki

"At the pre-construction foundations of the controlled waste disposal site built at the Port of Kinuura, the clayey soil account for the most, and with lesser amounts of sand compaction piles and sand mat. The cement deep mixing method (CDM) was used to improve ground impermeability and to reinforce the foundations on the seawall. Laboratory mixing and testing was performed to determine the appropriate quantities of cement additive for clayey soil, SCP sand, and sand mat. The test results indicated that maintaining the design strength of qu = 1,550 kN/m2 would require C = 100 kg/m3 of cement additive for all three soil types (clayey soil, SCP sand, sand mat). The permeability performance needed to improve ground impermeability assumes a permeability coefficient of K = 1.0×10-6cm/s. And the clayey soil satisfied the performance requirements at C = 100 kg/m3. However, to improve grand impermeability of the SCP sand and sand mat required more than 5% of particles having diameters of less than 75 µm. Thus, in the latter two cases, the required cement adding quantity was C = 250 kg/m3. The test specimens at one to two weeks after the created with a permeability coefficient of K = 10-6cm/s became permeability coefficient of K = 10-7cm/s six week later due to the effects of cement solidification. So the permeability coefficient declined about one order. The permeability coefficient three months later tends to decline continued with a somewhat lower.INTRODUCTIONBetween 2008 and 2011, the Aichi Seaside Environment Center constructed the Kinuura No. 3 offshore controlled waste final disposal site at Taketoyo in Aichi prefecture. (see Figure 1). The disposal site offers a landfill capacity of 5.21 million m3 and measures 472,000 m2 in area, of which some 344,000 m2 is a managed controlled sector enclosed within an impermeable seawall."

Jan 1, 2015

By Lewis Martin

Spokane Research Center personnel are currently conducting research on cable bolts to assess their material and support properties, to provide design criteria for roof control systems under various types of underground mining conditions, and to provide background data for computer models of cable bolt supports. Laboratory studies of cable bolts made of conventional steel cables with Garford bulbs and collars resulted in recommendations on characteristics such as embedment length, hole diameter, cable bolt diameter, and configuration of cables. A completed series of laboratory tests has determined the minimum embedment length of resin required for resin-grouted, cable bolt ground support.

Jan 1, 1996

By Patrick R. Taylor

Glass is used for immobilization of radioactive and hazardous wastes due to its durability and ability to accept a variety of waste constituents into its network structure. Alternative high temperature vitrification techniques have the advantage of increased throughput, increased waste loading and being applicable to variable and heterogeneous waste streams. However, the increased processing temperature places further concerns on the increased volatilization of contaminants, and increased corrosion and erosion of me Iter components. A database of melt properties at higher temperatures, such as partitioning, viscosity, density and electrical conductivity, in the temperature range of 1400-20000 K are being developed.

Jan 1, 2000

By Tang Chaoho

Laboratory research on the reducing and matte smelting of Jamesonite concentrate has been carried out. The influence of the process conditions such as the smelting temperature, the amount of pyrite cinder (the agent of fixed sulfur) and the amount of additives on the smelting process have been studied. Under the optimum condition the direct recovery ratios of antimony and lead are 83.26% and 68.50% respectively. The ratio of fixed sulfur is 98.97% but more than 15% lead and 30% silver remained in the ferrous matte. The key problem to be solved of this new process is how economical and effective is the recovery of silver and lead in ferrous matte.

Jan 1, 2003

By Tang Chaoho

Laboratory research on the reducing and matte smelting of Jamesonite concentrate has been carried out. The influence of the process conditions such as the smelting temperature, the amount of pyrite cinder (the agent of fixed sulfur) and the amount of additives on the smelting process have been studied. Under the optimum condition the direct recovery ratios of antimony and lead are 83.26% and 68.50% respectively. The ratio of fixed sulfur is 98.97% but more than 15% lead and 30% silver remained in the ferrous matte. The key problem to be solved of this new process is how economical and effective is the recovery of silver and lead in ferrous matte.

Jan 1, 2003

By D. A. Wheeler, Rémi Tremblay

"INTRODUCTIONDuring the last few years, through Column Flotation Company of Canada ltd, the Centre de Recherches minérales has worked on the column flotation of coal, phosphate, feldspar, talc, graphite, copper, lead-zinc and diamond ores. The operating companies and prospective deposits were located in Canada and in other countries. Since these projects were financed by the concerned mining companies, all results remain confidential unless we obtain permission to publish. Three companies have graciously allowed us to use their information which I will describe in this text. These are the Polkowice copper mine in Poland, the North Coast Industries ltd graphite deposit and a talc company which preferred to remain anonymous. I will also describe our 2 inch column which was used for all tests. Data is also given on how to scale-up the 2 inch column to industrial size.Figure 1 presents a schematic of a flotation column. Feed, at a controlled rate and pulp density, enters at about 1/4 of the height of the column from the top. A controlled rate of air is bubbled into the bottom of column through a fine-holed sparger. The column volume between the feed point and the top of the sparger is called the recovery zone. Tailings, at a controlled rate, always slightly greater than the feed rate, discharges from the bottom of the column. This difference in feed and tailings flowrates is called the bias. The floated mineral is carried through the recovery zone on air bubbles which rise into the cleaning zone which is that column volume between the feed point and the overflow at the top. As the bubbles rise in this zone they are washed of gangue material by wash water which enters over the top of the froth layer. The froth layer is maintained at a given depth during flotation but this depth will depend on the froth cleanliness, for quite a bit of cleaning by wash water is accomplished in this layer."

Jan 1, 1988

By Robert Vidal

The performance of a laboratory-scale cell for the electrolysis of an aqueous chrome alum solution was studied. Electrode potentials, pH, and Eh were recorded. An optimum catholyte pH of about 2.5, consistent with information from the literature was observed. Values exceeding this range resulted in a precipitate formation and are detected by wavering cathode potentials. The role of anodically produced dichromate ions was investigated by chemical analysis. It was found that the steady state concentration of dichromate ions varies inversely with fluid flow from catholyte to anolyte. This concentration was also reduced with the use of precious metal coated titanium anodes.

Jan 1, 1994

By J. A. Beukes, M. Marais

TICOR South Africa is a new titanium feed stock producer. In the Ticor South Africa plant the ilmenite feed to the smelter plant is roasted to enhance its magnetic properties. This allows for the magnetic separation of chromite from the ilmenite. The magnetization reaction relies on partial oxidation with both under- and over-oxidation causing insufficient magnetization. To subject the roaster plant feed material to the required physical conditions a circulating fluid bed (CFB) roaster is used. This paper describes the development of a laboratory model that will aid in the control of the CFB roaster.

Jan 1, 2003

"Successive seismic waves may cause progressive weakening of a fault zone, which has been recognized as the mechanism of earthquake aftershocks. However, it is unclear that how a fault zone slips under each wave cycle and how slip displacement accumulates under continuous wave cycles. This laboratory study provides direct evidences on the slip process of a simulated granular fault zone dynamically induced by an incident wave without the effects of late-arriving and reflected waves. The experimental observations show forward and backward slip paths of the fault zone and partially recovered slip displacement after a wave incidence. The unrecovered slip displacement after each wave cycle can be accumulated until it reaches a critical slip distance for seismic faulting, which may reinterpret delayed triggering in earthquake dynamics. The limited interseismic period restricts fault self-healing in strength. The experimental results also indicate that the dynamically induced frictional slip on the fault zone is associated with a complex frictional system, including seismic wave radiation, frictional slip initiation and normal stress vibration. Different from the dynamically induced frictional slip on the fault zone, the statically induced frictional slip causes a permanent increase of slip displacement along the shear loading direction. INTRODUCTIONAn earthquake mainshock may induce aftershocks by suddenly changing external stresses applied to another fault zone in the near field (Kilb et al., 2000) and by slightly perturbing a fault zone from a critical steady state to stick-slip faulting in the far field (Gomberg and Davis, 1996). The dynamically induced frictional slip on a fault zone has been recognized as the mechanism of earthquake aftershocks (Marsan and Lengliné, 2008; van der Elst and Brodsky, 2010). Although earthquake aftershocks have been extensively studied by many seismological methods, a simplified laboratory fault zone can provide possible interpretation on real faulting and detailed analysis on a friction process (Dieterich, 1979; Nielsen at al., 2010). According to a few laboratory experiments related to the dynamically induced frictional slip on a simulated fault zone (e.g., Uenishi et al., 1999; Johnson et al., 2012), the slip process induced by successive seismic waves exhibits continuous motions. However, it is unclear that fault slip response under each wave cycle and slip displacement accumulation under continuous wave cycles."

Jan 1, 2015

By M. C. Bétournay

Strainbursts are common in overstressed brittle rock around deep mine openings. Such failures are characterized by a biaxial state of stress in the plane of the opening boundary. A zone of compressive stresses imposes initial failures near or at the surface of the opening that results in spalling of thin slabs of rock roughly parallel to the free face. While the failure of rock under biaxial loading conditions is increasingly common in deep underground mines, only a few representative laboratory studies have been reported in the literature, without emphasis on rockbursting aspects, and none in the last decade. This paper presents the results of a testing program on a granite rock type. Biaxial testing, conducted on 100 mm cubic samples, was carried out to examine the influence of lateral confinement and loading rate on the rock’s ultimate strength. The paper reports the test results in terms of normalized biaxial failure envelope s1/sc-s2/sc. A discussion of the failure mechanisms observed is presented. Les coups de toits de déformations sont choses communes dans le rock cassant surcontraint en place autour des ouvertures minières profondes. De telles ruptures sont caractérisées par un état de contraintes biaxiales dans le plan de la périphérie de l’ouverture. Une zone de contraintes compressives impose des ruptures initiales à ou près de la surface de l’ouverture, qui produit des relâchements de minces plaques de roc plus ou moins parallel à la surface. Bien que les ruptures de roc sous des conditions biaxiales sont de plus en plus communes dans les mines à grandes profondeurs, il n’y a eu que quelques études représentatives en laboratoire de publiées, sans emphase sur des aspects de coups de terrains, et aucunes publiées depuis la dernière décennie. L’article présente les résultats d’une campagne d’essais appliquée à un type de granit. La campagne d’essais biaxiaux, sur des échantillons cubiques de 100 mm, avait pour objectif d’examiner l’influence du confinement latéral et le taux de chargement sur la résistance ultime du roc. Cet article fait part des résultats en terme de l’enveloppe de rupture biaxiale normalisée s1/sc-s2/sc. Une discussion sur les mécanismes de ruptures observés est présentée. Dehnungsbrüche findet man häufig in übergespannten spröden Felsen um die Öffnung von tiefen Minen. Solche Brüche sind von einer zweiachsigen Spannung in der Ebene der Grenze der Öffnung charakterisiert. Eine Zone von Druckspannungen verursacht initiale Brüche, entweder an der Öberflache der Öffnung oder in der Nähe. Davon scheiden sich dünne Felsplatten mehr oder weniger parallele mit der freien Wand. Obwohl Felsbrüche unter zweiachsiger Beanspruchung immer mehr häufig in tiefen Minen beobachtet sind, hat man über nur einige repräsentative Laborversuche in der Literatur berichtet. Diese Studien diskutieren das Thema ohne Betonung auf Felsbrüchen, und keine sind in den letzten zehn Jahren erschienen. Die vorliegene Arbeit gibt die Ergebnisse eines Testprogramms auf einem Typ von Granitfels. Durch zweiachsige Prüfungen von kubischen Proben mit Seitenlangen von 100 mm sollte man den Einfluss von seitlicher Ermittlung und der Beanspruchungsrate auf die Bruchfestigkeit des Felsen studieren. Man findet auch die Prüfergebnisse in bezug auf das normalisierte, zweiachsige Bruchkriterium s1/sc-s2/sc. Die beobachteten Bruchmechanismen sind auch diskutiert.

Jan 1, 2003

By Quast K. B

Samples of limestone and micaceous hematite have been ground in a laboratory batch mill using equal weights of either rods or balls. Values of the Schuhmann distribution modulus, a, have been shown to depend on grind time and do not remain constant as often reported. The linear reduction in a with grind time was attributed to a change in grinding mechanisms with time. The product sizing from ball milling limestone showed a bimodal distribution, but rod milling produced a unimodal size distribution. The product sizing from milling micaceous hematite was difficult to interpret due to the major influence of the shape factor on the transition from screen sizing to cyclosizing.

Jan 1, 1995

By K B. Quast, A Schuurmans

Laboratory batch rod and ball milling tests were conducted on samples of Heavy Medium Separator (HMS) sinks from Renison Limited. The effects of mill rotation speed, rod volume and ball size on the resulting product size distribution were investigated. Between 48 and 69 per cent of critical speed, the product sizing distribution curves remained very similar, with a finer grind resulting from increasing the speed of rotation at constant grind time. Increasing the rod loading from ten to 53 per cent by volume caused the product size to become finer and more closely sized with a transition occurring at approximately 29 per cent. This was interpreted as a change of dominant grinding mechanism from abrasion to impact. No preferential grinding of the cassiterite was observed. The effect of increasing ball size at constant charge weight was to preferentially grind the coarser particles and generate more intermediate sized particles, whereas the product from a mixed ball charge gave a distribution similar to that obtained when a charge containing only smaller balls was used.

Jan 1, 1998

By K B. Quast

Changes in feed size distribution can have significant effects in rod mill grinding. The product sizing resulting from wet batch milling of a tin ore showed little influence on fines production after truncating the feed at either the coarse or fine end. The addition of fine material caused a less amount of fines to be produced and a possible increase in grinding at coarse sizes, although this is complicated by the changing feed size distribution. The changes in feed size distribution caused no tendency for preferential grinding of the cassiterite.

Jan 1, 1998

It is possible to closely simulate the product sizing distribution from an industrial rod mill by the correct choice of parameters in laboratory batch milling. For laboratory batch rod milling, changes in per cent critical speed and per cent rod volume cause the product sizing distributions to move in parallel at a constant slope. For ball milling, larger sized media in batch milling grind more coarse material giving a closer simulation to the industrial rod mill product. Changing the feed size distribution by removal of coarse particles or addition of fine particles changes the product sizing distribution, but would not normally be practiced in laboratory testing. These data should be applicable to many instances where laboratory simulation of an industrial product size distribution is required.

Jan 1, 1998

By P G. Hicks

The influence of feed size and pulp density on the specific rate ofbreakage of quartz was investigated. Plots of log fraction of feedremaining within the feed size interval against grinding time allowed the application of the first order grinding model to be examined. Substantial non-linearities were observed for all feed sizes due to environmental and material factors. For feed sizes above 1.3 mm, the specific rate of quartz breakage was higher with rod milling than ball milling, but below this size the reverse was true. Material that remained in the feed size interval after the initial grinding broke more slowly in subsequent grinding than the original feed material. Grinding media and time as well as feed size influenced the effects of pulp density on grinding. More dilute pulps (eg 50 per cent solids density by weight) were favoured for higher rates of breakage in rod milling but for ball milling, the optimum pulp density appeared to be 60 to 70 per cent solids by weight.

Jan 1, 1998

The usefulness of laboratory studies - petrology and mineragraphy in the search for, and investigation of, mineral deposits should not be exaggerated, but it should not be overlooked, because such studies will always contribute to an understanding of the geology of the deposits, and can on occasions provide invaluable information not otherwise available. A few examples furnished by the investigations of the Mineragraphic Section of the Commonwealth Scientific and Industrial Research Organisation will show this.Petrology.In the early stages of the investigation of the King Island scheelite deposit, during the war, when the nature of, the deposit was not understood, a series of samples embodying the exposed rock types was submitted to the Mineragrap;hic Section for petrologicalexamination by the Mineral Resources Survey. It was at once apparent to the petrologist that the King Island scheelite ore was a contact metamorphic deposit, in which a series of argillaceous shales, calcareous shales, impure limestones and limestones had beenintensely metamorphosed. The shales had been converted to finegrained biotite and actinolite hornfels, according to their lime content, and the impure limestones to fine-grained diopside hornfels, garnetdiopside hornfels and garnet hornfels (calc-flint), the garnet being the lime variety grossularite. The limestones, however, after being first converted to marbles, had suffered intense pyrometasomatism, involving substitution of immense quantities ,of silica and' iron for lime and carbonate, and had been converted largely to a coarsegrained garnet rock, in which the garnet was the lime-iron variety, andradite. The silica and iron were derived from the mineralising solutions of the adja,cent ,granite. intrusion, responsible for the contact metamorphism, and were accompanied by tungsten and some molybdenum. The tungsten in the presence of so much mobile lime, was precipitated as schecelite, much of it finegrained and enclosed in or intergrown, with the andradite garnet or the quartz interstitial to the garnet.It was apparent that the King Island scheelite deposit, was a perfect example of selective pyrometallomatic replacement in a bedded contact metamorphic deposit. The bedded nature of the original rocks was preserved, and the scheelite was practically limited to the original limestone beds, 'Which had been so much more susceptible to replacement after recrystallization, than the other sediments. The further geological study of the deposit then resolved itself into the task of mapping the folding and faulting of the deposit, with bore cores to provide the stratigraphic sequence, and establish the number of scheelite-bearing beds.A second example is provided by a petrological investigation of the mineral composition and genesis of the talc deposits of the Gumeracha district of South Austral.ia, which was undertaken at the request of the South Australian ,Mines Department, in conjunctionwith mapping of these deposits. The field geologist mapping the deposits was experiencing some difficulty in interpreting the structure...

Jan 1, 1950

By H. R. Hardy Jr., E. J. Kimble Jr., H. W. Shen

"The primary objective of this research project is to study the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. Secondary objectives include the investigation of the acoustic emission technique as an indirect method for coal dust characterization and remote bit wear monitoring. The results of the project will be useful in developing efficient coal cutting techniques which significantly reduce the harmful coal dust components, and in providing methods for remote monitoring of bit condition and associated coal dust character. This paper will outline recent experiments carried out on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. During the experiments acoustic emission and a variety of other mechanical parameters were monitored. · A commercially available artificial intelligence computer package, namely: JCEPAK (Intelligent Classifier Engineering Package), has been utilized to provide a powerful and objective means for AE waveform analysis. This program is able to evaluate a number of features of each AE event and to make objective comparisons between AE signals associated with different loading or cutting parameters. Finally, the paper will discuss the results obtained from a variety of coal breakage tests.INTRODUCTIONStudies to date clearly indicate that the reduction of the severity, and eventual elimination, of Coal Workers' Pneumoconiosis (CWP) depends on gaining fundamental understanding in a number of major areas. These include dust generation and entrainment, transportation, suppression, medical effects of dust and possible treatment. At present a project is underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which will make it possible to carry out remote monitoring of coal cutting operations. Suitable on-line analysis of monitored AE data would allow engineers to evaluate factors such as shearer bit condition and cutting efficiency, and to quantify the particle size and shape distribution of the generated dust. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal cutting procedures. This paper will outline recent experiments on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. Additional information on these studies are presented elsewhere [4]."

Dec 1, 1996

By William A. Hockings

This report describes the results of laboratory studies on leaching of copper ores.tlf These studies are the first step of a program for the investigation of in situ leaching of tabular, metalliferous ore bodies.(2) The basic steps required in the development of an in situ process are: 1. Leachability - the ability to dissolve the metal values from the ore under in situ conditions must be demonstrated. 2. Ore Preparation - the ore must be prepared so that sufficient contact with the solution can be attained. 3. System Design - integrated in situ systems must be designed and studied for engineering feasibility. 4. Economic Feasibility - the economics of the system must be shown to be economically feasible and competitive. 5. Environmental Feasibility - the loss of reagents into the environment must be investigated. 6. Pilot Scale Testing - the feasibility of the system must be demonstrated on a sufficiently large scale. The studies described in this report were concerned only with the first step of the program, viz., leachability. Native and sulfide copper ores from the Michigan copper district were selected as model ores for these studies. Aqueous amnonia solutions were chosen as the solvents to be investigated. In this study carbonate (CO3, HCO3, H2CO3) was used exclusively as the anion. In keeping with custom it is referred to as carbon dioxide and concentrations are ex- pressed in terms of CO2. When leaching native copper the reaction is

Jan 1, 1976

Neutralization with lime is a simple, cheap, and effective means of treating acid raffinates from uranium processing to' raise the pH, reduce the concentrations of dissolved salts (including heavy metal impurities), and remove amine by adsorption. Two-stage neutralization, using limestone in the first stage at approximately pH 4 and lime in the second, lIlay be advantageous.Lime neutralization of mffinates in the pH range 7 to 8· 5 generally reduced the radium ·concentration to 10 to 200 pCi 1-1, but ·there was considerable scatter in the experimental data. The radium concentration was further reduced to less than 3 pCi 1-1 by co-precipitation of barium (radium) sulphate with 10 mg Ba (as barium chloride) per litre of raffinate. Adsorption of radium on barytes was -also effective in reducing the radium concentration in neutralized raffinate to less than 3 pCi 1-1.The radium concentration of pit water was readily reduced to less than 3 pCi 1-1 when pit water containing 0·01 M sulphate as ammonium, calcium, or sodium sulphate was treated with 20 mg Ba per litre of pit water.Adsorption on barytes was also effective in removing radium from pit water containing 0·03 M sulphate.

Jan 1, 1975