Search Documents

By Sarah K. DeBono, Alan J. Monaghan, Emmanuel V. Manlapig, Gregory J. Harbort

"The Jameson Cell is a type of flotation machine in which air and pulp are brought together in a vertical tube called a downcomer. Within the downcomer the air and pulp are dispersed into a dense foam of fine bubbles, which creates a favourable environment for bubble-particle collision and subsequent collection of hydrophobic particles. The intense collection zone within the downcomer can be considered similar to the zone between the rotor and stator in mechanical flotation cells.Research into the bubble-particle collision and fluid dynamics of mechanical cells rotor-stator zone has been limited by the difficulty of achieving accurate measurements in production sized machines. With the Jameson Cell the downcomer is largely external and separated from the flotation tank, allowing ready access to the primary contacting zone for measurement and analysis.An investigation has been undertaken into the operating characteristics of the downcomer relating to bubble-particle collision. An effective mapping of the downcomer has been made through measurements of void fraction and bubble size taken across cross sections of the downcomer. Analysis of these measurements has provided an interpretation of the variations in the air and fluid dynamics, bubble size and distribution throughout the downcomer chamber."

Jan 1, 2003

By B. Holen, J. R. Baregi, J. A. Organiscak, A. B. Cecala

The National Institute for Occupational Safety and Health (NIOSH) cooperated with 3M Company in the design and testing of a new environmentally controlled primary crusher operator booth at the company’s Wausau granite quarry near Wausau, WI. This quarry had an older crusher booth without a central heating, ventilation and air conditioning (HVAC) system, and without an air filtration and pressurization system. A new replacement operator booth was designed and installed by 3M based on design considerations from past NIOSH research on enclosed cab filtration systems. NIOSH conducted pre-testing of the old booth and post-testing of the new booth to assess the new filtration and pressurization system’s effectiveness in controlling airborne dusts and particulates. The booth’s dust and particulate control effectiveness is described by its protection factor, expressed as a ratio of the outside to inside concentrations measured during testing. Results indicate that the old booth provided negligible airborne respirable dust protection and low particulate protection from the outside environment. The newly installed booth provided average respirable dust protection factors from 2 to 25 over five shifts of dust sampling with occasional worker ingress and egress from the booth, allowing some unfiltered contaminants to enter the enclosure. Shorter-term particle count testing outside and inside the booth under near-steady-state conditions, with no workers entering or exiting the booth, resulted in protection factors from 35 to 127 on 0.3- to 1.0-µm respirable size particulates under various HVAC airflow operating conditions.

Jan 1, 2015

Apparently there is little inclination on the part of mining engineers to supplant the transmission of power by compressed air with it's formidable rival, electrical transmission. No doubt there are many advantages to be claimed for compressed air that render it parculiary well suited for the conditions which characterise underground work.

Jan 1, 1902

By Willis H. Carrier

PARTICULAR interest in the ventilation of deep mines, especially those in South Africa, has been created by a very complete system of cooling of the world's deepest mine, the Turf shaft of the Robinson Deep in Johannesburg. The writer visited this mine in January, 1936, and again in 1937. During these visits and subsequently, a considerable part of the theory involved in rock cooling in tunnels was developed and this has been checked by practical observations of the rates of rock cooling made within mines. The purpose of this paper is to set forth the method of attack of the mine problem. The cooling or air conditioning of mines by the use of mechanical refrigeration was not wholly new 1-5 when the Robinson Deep installation was made. The first mine to be cooled was the Morro Velho mine, in Brazil. The first installation in this mine was put into operation in December 1920, the refrigerant being ammonia.5 The surface cooling gave considerable benefit but it proved inadequate as greater depths were reached, therefore in 1929 two centrifugal refrigerating machines were installed at the 6000-ft. level. These were used in conjunction with the surface cooling system to furnish additional cooling at the lower levels. This later installation used Carrene as a refrigerant. This nonflammable refrigerant, having a boiling point of 104º at sea level, insured reasonable safety, since all parts of the machine operated at subatmospheric pressure. Very favorable reports have been received on the effectiveness of this installation, but no recent data are available. An interesting feature of that plant is that the condenser water is cooled by spraying it into the exhaust air from the mine at the base of the ventilation upcast, which permits the water to be cooled within a few degrees of the wet-bulb temperature of the air entering the upcast, and the only water that has to be supplied for condensing purposes is that lost by evaporation, or about 0.5 per cent of the volume circulating through the condenser. This plan affords an ideal means for the removal of the heat load from the refrigerating system, and of course also from the mine itself. In many mines, however, especially those in South Africa, there is no

Jan 1, 1938

To reduce the exposure of mining machine operators to respirable dust. Approach: A protective curtain of filtered air is blown down around the operator's head, from a manifold mounted on the machine canopy. How It Works: Mine air is drawn into the system through a filter which removes respirable dust. The filtered air enters a centrifugal blower which pushes it through a flexible hose to a manifold mounted on the canopy above the operator. Air leaves the manifold through a perforated plate and flows down around the operator's head. A photograph of an installed system can be seen in Figure 1. The second photograph, Figure 2, shows the sys-tem components. An important advantage of this dust protection system is that it is not worn or carried, or in any way connected to the operator. It is therefore not uncomfortable, encumbering, or

Jan 1, 1976

By S A. Steyn, P Terrett

Air decking has become a widely practised method internationally for modifying fragmentation results and providing cost savings from reduced explosive consumption. Duvha has been applying air deck technology to overburden and midburden blasting for a few years. A thorough evaluation of air decking at Duvha has been made by instrumenting a number of blasts and analysing costs from direct savings in reduced explosives costs to savings in improved dragline productivity.

Jan 1, 1995

By E. S. Peters, M. J. van Rensburg, M. Le Roux, Q. P. Campbell

"The demand for energy has continued to rise worldwide in line with population growth. The majority of South Africa’s electricity is supplied by coal-fired power stations. The amount of fine coal (-2 mm) generated at coal processing plants has increased, due mainly to mechanized mining methods. Fine coal retains more water, which lowers its heating value.Drying the coal is costly and it is difficult to achieve the required moisture content. Consequently, coal fines are often discarded. An estimated 8% of the total energy value of mined coal is lost1.Fluidized bed technology is often used to dry coal thermally, but this method is expensive and has an adverse environmental impact. The objective of this study was to investigate the removal of moisture from fine coal (<2 mm) in a fluidized bed operated with dry fluidizing air at moderate temperatures as the drying agent. The effects of different air temperatures and relative humidity levels were investigated in a controlled environment. The study further investigated the influence of coal particle size on moisture removal.The drying rate was found to increase with increasing temperature. The relative humidity of the drying air had a more pronounced effect on the drying rate, even at temperatures as low as 25°C.. It became more challenging to remove moisture as the particle size decreased. The gain in calorific value was greater than the energy required to dry the coal samples, showing that a fluidized bed using moderately warm dry air is an energy-efficient drying technology. The energy efficiency of the fluidized bed compared favourably with other thermal drying methods.Paper written on project work carried out in partial fulfilment of Degree in Chemical Engineering(NWU) - Pursuing Masters in Coal Beneficiation"

Jan 1, 2015

By Y. P. Chugh

A novel dry and wet air dust filter concept was conceived and demonstrated successfully at two mines. A steel-wool and a fiberglass filter, suitable for underground use were identified through laboratory testing and demonstrated in the mine. The steel wool filter was operated with and without water sprays while the fiberglass filter was only operated in the dry mode. The dry steel wool filter provided a dust capture of 37% at a negligible pressure drop. When fine misting water sprays were used on the steel wool filter, the dust capture increased to 51% again with a negligible pressure drop. The filter screen also remained clean and no change in air flow characteristics was observed as a function of time. The dry fiberglass filter however did not perform as well achieving only 11% dust capture while introducing a significant resistance to air flow. This technology is seen to have several applications in underground coal mines.

Jan 1, 2009

By S. S. Peng

The generation and transportation of the airborne dust are mainly governed by the velocity and the movement pattern of the ventilation air in the longwall face. Generally speaking, the higher the air velocity, the more the airborne dust will be generated and the longer the period of the dust of certain size will be carried away from the source. In order to effectively prevent the production and the spread of the airborne dust, The airborne dust concentration distribution in the longwall face must be known in advance. Before the dust concentration distribution can he predicted theoretically with confidence, the air velocity distribution pattern of the ventilation air in the longwall face area must be determined first. However, the complicated, time-dependent and unpredictable mining conditions along and around the face area make the theoretical studies of the problem rather difficult. For instance, one of the factors commonly affecting the air velocity distribution at the longwall face is the air leakage, either into or from the gob area. The leakage quantity and the location of occurrence differ from mine to mine, face to face, and time to time. They depend not only on the compactness of the caved roof fragments in the gob, but also on the degree of obstructions in the working space and in the return entry. Another obstacle to the theoretical studies about the velocity distrbution is the complicated boundary conditions of the ventilated spnce which is very difficult to represent accurately in mathematical forms. In this paper, the air velocity distributions measured in four longwall faces are presented. A statistical model for each longwall face is also derived for prediction of air velocity distribution in the longwall face.

Jan 1, 1985

By Samuel S. M. Chan

Rock surrounding mine openings frequently is an impermeable type such as shale or granite. Most rock, however, has joints, bedding planes, cleavage planes, or other potential discontinuities. Permeability to fluids (gas or liquid) may exist via natural joints or fractures in an otherwise impermeable rock. In the mining situation, tectonic and induced tensile and shear stresses may be great enough to cause joints to open or fractures to develop in previously solid rock. The rock, as a result, becomes less self-supporting and may - require artificial support such as rock bolts or timber. Simultaneously, as fractures develop, permeable paths may be created. If fluid can be injected into a previously solid and impermeable rock mass, a logical conclusion is that a fracture (crack) flow path must be transmitting that fluid. The U.S. Bureau of Mines Laramie (Wyo) Energy Research Center has been evaluating results of in-situ oil shale fracturing (hydraulic or explosive) and retorting experiments by. a fluid (air) injection , and borehole air flow profile logging technique since 1956 (1, 14, 15). In the oil shale case, it is imperative to know the location and flow capacity (permeability) of natural fractures, if they exist, and induced fractures that inter-connect vertical wellbores at depths of fifty to several hundred feet. By injecting air into one wellbore in a system of several wells and measuring input volume and pressure while simultaneously measuring the output of other wellbores, the minimum areal extent of interconnecting permeable fractures can be determined. Exact locations (depths) of fractures and individual fracture flow capacities between wellbores can be determined by air flow profile logging (14, 15). Knowledge of fracture locations and permeability is essential to rational experimental in-situ retorting design.

Jan 1, 1973

By R. J. Sweigard

Deep tillage is used widely as a Means of alleviating excessive soil compaction. There has been some concern that the voids created by deep tillage may collapse before a more natural soil structure develops, resulting in recompaction subsequent to deep tillage. A laboratory investigation was conducted to determine the feasibility of pneumatically injecting organic material into the voids during deep tillage to prevent any significant recompaction from occurring. Various amendments were injected into the soil in the laboratory using a small-scale ripping and injection system. Measurements were made of selected soil properties to evaluate the feasibility of this method.

Jan 1, 1993

By Pingyang Zhang, Caichu Xia, Shuwei Zhou, Yu Zhou, Yongsheng Hu

A lined rock cavern (LRC) is an alternative container for compressed air energy storage (CAES) to store high-pressure air that is later used to produce electricity. A critical requirement of CAES in LRCs is that the inner seal should provide adequate sealing capacity to prevent air leakage from LRCs. In many studies, rubber sheets are applied to build the inner seal. However, air leakage through rubber seals has not been given much attention and rubber seals are usually assumed to be absolutely airtight. Given that rubber is permeable especially under high air pressure, such as in CAES, air therefore leaks through rubber seals during CAES operations. In this study, a numerical analysis was conducted based on the permeation equation of polymers and the governing equations of thermodynamics of CAES caverns to analyze the characteristics of air leakage from CAES caverns through rubber seals. A planned CAES plant in China was considered as a case study. Results show that air leakage rate increases with increasing cavern temperature and pressure during air injection and decreases as cavern temperature and pressure decline during air withdrawal. However, in total, the daily air leakage percentage is in the order of magnitude of 10-3% in a typical operation cycle, which is much smaller than the critical value of 1%. Under a common range of realistic operations conditions, the daily air leakage percentage is still of the order of 10-3%. Therefore, rubber seals can be used to prevent air leakage in LRCs for CAES. However, the experience of Japanese pilot cavern indicates that the specifications for the on-site vulcanization jointing and installation methods of rubber seals still need improvement.

Jan 1, 2015

By A. K. Singh

Between the main fan and the coalface in a mine a lot of air is lost through leakage at stoppings, doors, air-crossing etc. so that a much larger quantity of air has to be circulated by the fan in order that the stipulated quantity of air reaches the face. Stoppings are of vital importance not only for effective ventilation of underground mines but also for isolation of areas affected by fire or susceptible to spontaneous heating. Generally, isolation stoppings are made of brick in cement mortar. If the area is far from the pit or unapproachable, it is very difficult and sometimes impossible to build these stoppings. To overcome these difficulties, particularly near fire affected zones, an alternate successful attempt was made in Indian mines to make a plug underground, from surface through borehole, using cement concrete. In this paper the salient features of the methodology adopted for construction of the plug and the experimental procedure for the measurement of air leakage by SF6 tracer gas is described. Measurements of air leakage through rows of ventilation stoppings in two mines viz. Moira (Jambad and Kajora seams) and Kuardi11/12 (Niga seam) collieries of Eastern Coalfields Ltd. (ECL) have been incorporated. Results of experiments conducted at the Central Mining Research Institute (C.M.R.I) to determine leakage through25 and 38 cm thick brick stoppings are also discussed. Results of all these studies are compared, which show that the efficacy and reliability of the remote filled cement concrete plug in respect of air permeability is satisfactory.

Jan 1, 2004

By K. L. Rubow

"IntroductionAir sampling for airborne contaminants requires a system for moving air, a collection method, and a procedure to determine the quantity of contaminant collected. Because occupational exposure limits and air quality standards frequently are expressed in terms of concentrations, a method of determining the volume of air sampled is also needed. The four principal components in a sampling train are shown in Figure 12-1. The inlet admits the air sample into the train; the collector(s) separates the gas, vapor, or particles from the air; the flowmeter measures the rate or total quantity of air sampled; and the pump (air mover) provides the suction required to draw an air sample through the train. Inlet sampling considerations are discussed in Chapter 21. Various types of collectors are described in subsequent chapters. Flowmeters are discussed in Chapter 7.This chapter will describe the air mover portion of the sampling train and air sampling systems that contain three or four components in a convenient package. The chapter consists of two parts. The first part contains a brief description of the different types of air movers and air sampling systems. The second part consists of tables and figures showing detailed information on a wide variety of commercially available air movers and sampling systems. ient size is filled with a liquid in which the suspected contaminant is insoluble. When the liquid is allowed to escape from the vessel, it is replaced by air from the atmosphere to be sampled. Such an air sample is an integrated sample rather than an instantaneous sample because the mass of fluid requires a finite time to empty. In fact, by employing a large vessel with controlled drainage, this method can be used to move air at low flow rates through a sample collector for extended intervals. Additional discussion of this method can be found in Chapter 17."

Dec 1, 1996

By B S. Petri, N T. Rouse

Underground limestone mines generally lack air pressure monitoring procedures and instrumentation guidelines. The blasting industry also lacks an applicable source for air overpressure levels that are produced by blasting operations in underground mines. This became apparent during the development of a new underground limestone mine, where overpressure levels from production blasting needed to be estimated. During the development phase of the mine, it was imperative that newly constructed underground structures be capable of withstanding the overpressure produced by blasting. Therefore, a study was conducted to (1) identify and review any published studies for data that may be applicable, (2) identify the appropriate equipment required to record the overpressure levels, (3) determine the proper procedures for setting up the equipment and recording overpressure, and (4) provide an understanding of the nature of the air overpressure in a developing mine.

Jan 1, 2014

By Calvin Konya, Anthony Konya

State and Federal construction specifications require the Blasting Contractor to prepare a Master Blasting Plan which is reviewed by the Owner’s Representative. The Master Blasting Plan requires the Contractor to submit the design of a typical blast. Most blasting specifications also require the Blasting Contractor to submit Daily Blasting Plans. The Master Blasting Plan and the Daily Blasting Plan require that the Blasting Contractor also submit the types and quantities of explosives and initiators used. The specifications also request that the Blasting Contractor submit the pounds of explosive used per delay for both production and presplit blasts. The Blasting Contractor may also be required to predict the anticipated ground vibration and air overpressure levels for the proposed blasts. There are equations that can be used to predict the ground vibration. There are also equations that can be used to predict the air overpressure levels. The data for these equations were primarily derived from quarry and surface coal mine and some construction blasts. Data from major construction projects were analyzed in this study to determine new air overpressure propagation equations for construction blasting. These new prediction equations compare calculated results analyzed from field data with other existing air overpressure prediction equations. Production blasting air overpressure values are also compared to air overpressure from presplitting

Jan 1, 2015

By Luthie Els, Chris Coetzee, Roedolf Koekemoer, Casper Els, Olof Vorster, Frank Fereday

Three electric arc furnaces (EAFs) were constructed by Union Carbide at Tubatse Ferrochrome (TFC) in1975. This plant was expanded to four furnaces at the East Plant in 1985 and the gas cleaning system was enlarged without taking flow dynamics into consideration. In order to improve competitiveness, TFC has increased furnace capacity, partially substituted coal for coke, and changed the charge mix. These changes increase the heat and dust load into the air pollution control (APC) system. TFC embarked on a project to improve the APC capacity by: ?Quantifying the required off-gas capacity ?Optimising the aerodynamic flow through the system by means of Computational Fluid Dynamics (CFD) ?Converting the old Brandt Koyo top entry baghouses to bottom entry ?Upgrading the cleaning system ?Installing Gore-tex® ePTFE membrane filter bags The estimation of required off-gas capacity is traditionally done by rule-of-thumb methods such as specific extraction. A more elegant evaluation method was developed for simulating the effects of changes in charge mix on the furnace reaction gas volume and the APC system. Reaction gases are calculated by modelling the reactions taking place in the furnace and off-gas volumes are compared to both fan and baghouse capacity. This enables identification of bottle-necks in the off-gas system. CFD techniques were utilized to evaluate geometric imbalances and propose solutions to ensure optimal use of off-gas capacity. The system modifications were completed over several months and the modified equipment went into service in May2006.

Jan 1, 2007

By Leo R. Love

A comprehensive study of the environmental conditions of the area affected by the Colfax and Cheswick Power Stations is of extreme importance to Duquesne Light Company. The residents in the valley where the two plants are located have complained for many years about the emissions from the Colfax Plant which is of the 1920 to 1930 vintage and which has a capability of generating approxi¬mately 200 Mw. They were extremely happy to hear that the Company had plans for shutting it down, however, they were extremely unhappy to hear that we were planning to build another even larger one to take its place in the same vicinity, namely the Cheswick Plant with a capability of 570 Mw. They had visions of a plant twice the size of the Colfax Plant and belching out twice as much smoke. A few of the citizens from that area were most vehement at the public hearings that were held by the Allegheny County Air Pollution Bureau for obtaining an installation permit. With two power plants already existing in that area (Duquesne Light Company&apos;s Colfax Plant and West Penn Power&apos;s Springdale Plant), the primary concern of the Allegheny County Air Pollution Control Bureau was that the Cheswick Station might increase air pollution levels beyond what they considered to be dangerous limits. It became very evident that the Allegheny County Air Pollution Control Bureau would be extremely reluctant to grant installation and operating permits unless they were satisfied that the new plant would not increase local pollution levels and that we were taking sufficient steps to monitor the emissions from our plants and also the ambient air in the general area. We concluded that an extensive air pollution monitoring program must be conducted in the area to determine the effects of the operation of our plants. The program was conceived with our consultants, NUS Corporation of Rockville, Maryland, and was begun in June, 1968. It was designed to accomplish several things: 1. Determine the effect on the ambient air of the operation of each of

Jan 1, 1972

By Glenn H. Damon

Concern about environmental pollution goes back many centuries, but until recently most efforts to control it have been perfunctory and spasmodic, aimed largely at coal smoke and other visible pollutants. Air pollution is to a large degree a byproduct of our economic development, and scientific knowledge of the causes and character of such pollution is more extensive than the technology to handle the waste byproducts of our industrial civilization. The removal of all constituents foreign to the air from the effluents produced by an industrialized society is obviously impractical at this time. There is widespread difference of opinion regarding acceptable ambient air concentration levels for the Various pollutants produced by combustion processes, but there is basic agreement that the pollution of the atmosphere must be controlled and eventually reduced. The magnitude of the air pollution problem has been increasing rapidly because our expanding economy calls for an ever-increasing consumption of energy, and fossil fuels are a principal source of energy. For example, the consumption of electricity has been increasing at an average annual rate of approximately 8 percent over the last 10 or 1.5 years. Table 1 shows the estimated emission of the principal pollutants into the atmosphere in 1966. The approximately 90 million automobiles, trucks, and buses on American highways contribute the largest proportion of pollutants to the atmosphere, but that fact does not alter the growing problems of the coal industry. You will note that sulfur oxides, particulates, and nitrogen oxides are all products of the combustion of coal. Of these air contaminants, sulfur oxides are now receiving major emphasis in terms of research to develop effective means for control, Table 2 shows that the combustion of coal produces approximately 60 percent of the sulfur oxides discharged to the atmosphere. While the utilization of coal is the principal source of particulate matter, this is not considered as serious a problem as it was in the early part of the century because of technological developments that have produced sound methods for the removal of particulates from waste gas streams.

Jan 1, 1968

? Develop a six year capital budget for future emission controls at Western Springfield Power Plant that would provide long-term operating certainty

Jan 1, 2005