Search Documents

By R P. Varden

This paper looks at the design of the Bentayga raisebore with subsequent back analysis using a LiDAR survey. A search for LiDAR raisebore assessment publications shows little work has been done on this subject. The paper examines the empirical design and RS2 modelling assessment with the bored condition. The high resolution of the LiDAR enabled mapping of weak structures that were located on the geotechnical investigation hole the orientations of which could not be determined. In addition, the scan showed were water ingress was occurring, potential stress overbreak and structural controls on stability. The LiDAR results were able to confirm no additional support work such as a shotcrete liner is necessary. The LiDAR results have been analysed in one metre increments as volume of overbreak against the empirical stability criteria (McCracken & Stacey 1989). The future use of LiDAR mapping over a range of rock mass conditions will provide quantification of the established empirical assessment improving its reliability. It is also a useful and accurate tool to monitor long term stability of a raisebore due to stress change or ore pass due to wear.

Mar 15, 2021

By Ivan C. Machado

Jaguar Mining Inc. is implementing a 1.1 Mtpy, 7-year LOM gold project in the Iron Quadrangle (?Quadrilátero Ferrífero?), Brazil. Construction is on schedule and startup is programmed for Q2 2010. Mill feed grade averages 4.43 g/t and LOM gold production is estimated at 800,000 oz. The project entails two sulfide underground mines and three oxide/transition open pit mines. A state-of-the-art flotation/gravity concentration/CIP Plant has been designed based on testwork carried out by internationally recognized Canadian, U.S., and Brazilian laboratories. The mass recovery of the flotation section is only ca 10%, while its gold recovery is about 90%. Therefore, the CIP-ADR Plant will treat only 10% of the solids mass contained in the mill feed, while 90% will be fully cyanide-free material that will be partially used to feed a Backfill Plant. The leached tailings will be conveyed to a rather small tailings dam, whose 20- m3/h supernatant solution will be treated by a new electrolytic technology. The plant design contemplates a High Density Thickener for the cyanide-free rejects exceeding the backfill demand and a Regrinding Section before the Leaching Circuit. The estimated overall metallurgical recovery sits around 92%. This paper focus on the use of modern technologies to reduce costs, risks, and liabilities.

May 1, 2010

By Smith Bracewell

First evidence of bauxite in Jamaica resulted from an analysis of a soil sample collected at Bull Savannah in 1938 during a systematic local investigation of the island's soil types. Results of subsequent work indicated the possibility of the occurrence of deposits of commercial grade and dimensions, and in 1942, with a view to emergency development of the deposits as a war measure, the Jamaican Government declared all bauxite in the colony to be Crown property.

Jan 10, 1958

How did you get into mining; were you from a mining town or mining family? Not at all. I grew up in northwest Kansas. I liked to hunt and fish, so I thought it would be fun to work for a company that made knives or guns. It seemed like metallurgical engineers would be something those companies could use, so I started in physical metallurgy. I got a summer job at the great Climax molybdenum mine near Leadville, CO shoveling muck onto conveyors. I was hooked. I loved everything about mining, so in the fall, I changed majors from physical metallurgy to mineral processing. For many years you actually discouraged young people from studying the mining disciplines. Could that be right? That’s true.

Jan 1, 2007

By Murphy A. S, Budod A

The Philex concentrator represents the first time Jameson Cells have been used in a cleaner scavenger application or in large scale flotation in roughing and scavenging. This necessitated a major change in Jameson cell design as well as a chan

Jan 1, 1997

By Griffin PT, Espinosa-Gomez R, Jameson GJ

Two major issues are to be addressed in the Copper Concentrator of Mount Isa Mines Limited. The first of these is the need to increase concentrator flotation capacity to increase copper recovery, while the second is the need to reduce the iron sulphide dilution to meet future smelting requirements. Extra capacity in the cleaner and retreatment sections of the concentrator have been identified as key target areas, with additional copper recovery of at least one per cent identified from plant trials. Extensive pilot plant tests have been undertaken to evaluate the performance of the Jameson cell compared to conventional mechanical cell and column circuits. This work has shown that Jameson cells present an opportunity to achieve the desired grade and capacity specifications at lower capital cost than available alternatives. This paper outlines metallurgical results of work undertaken in the Copper Concentrator, together with a summary of pertinent Jameson cell operating parameters investigated during the period.

Jan 1, 1993

By R. Tremblay, M. Burrows

"In the summer of 1990, pilot scale testing of a Jameson cell was carried out at Falcon bridge Limited, Kidd Creek Division. The Jameson cell is self aspirating and has fewer mechanical parts, thus it has a lower operating cost compared to conventional cells. This lower operating cost combined with positive pilot scale results, justified the evaluation of two full scale cells in the plant. The plant test had two mandates:1. Gain a thorough understanding of the cells operation and design constraints.2. Develop a flow sheet to replace three divisions of copper cleaner flotation.This paper provides an overview on the installation, commissioning and evaluation of the two Jameson cells acquired. The current status of the test program is also discussed.IntroductionThe Falcon bridge Limited-Kidd Creek Division concentrator is located in Timmins, Ontario. The concentrator, commissioned in 1966 and expanded in 1978, consists of four parallel grinding and flotation divisions utilising small cell (60 ft3) technology. With increasing pressure to maintain low operating unit costs a series of studies were undertaken to assess the impact of new technologies in the flotation circuits. The goals of the project were to improve productivity through increased metallurgical performance and/or reduced operating costs.One of the technologies investigated was the Jameson cell designed by Dr. Graeme Jameson of the University of Newcastle and marketed by MIM Holdings Limited, Australia. This style of column technology was chosen based on its potential for reduced capital and operating cost versus large conventional cells.The success of pilot testwork in 1990 led to the installation of two production sized Jameson cells beginning in October 1991. The units were to be used to confirm pilot results and determine equipment requirements for flotation modernisation. This paper will discuss the results and experiences Kidd Creek has had with the Jameson cell from pilot scale through installation and commissioning of the plant units."

Jan 1, 1993

By K. E. Barnes

"The “Jameson Cell” flotation cell was developed at Mount Isa Mines in the late 1980’s to address deficiencies in our flotation column installations. Early base metal installations had a variable record. The test work and trials showed they made an improvement metallurgically when operated correctly, but performance of the early installations was hindered by a range of operational and maintenance issues. The installations needed to be more robust, and we needed a better understanding of how to successfully integrate the cells into the plant flow sheet.During the 1990’s, Jameson Cells had great success in coal fines flotation and organic removal in SXEW applications, and became the standard in these applications in Australia. These installations improved the cell design and materials of construction and the cell flow sheet design, to make it low wear with self-regulating control, producing good performance with little operator input.These improvements have enabled a fresh look at the use of Jameson Cells in base metals. Recent new installations have shown significant benefits in “hybrid” circuits, that combine the best features of both Jameson Cells and conventional flotation cells, achieving better overall circuit performance in a smaller footprint than either technology could do by itself.Case studies of successful base metal applications are discussed, using size-by-size mineralogical performance to explain the improved circuit performance. The new methods of flow sheet test work design are also described."

Jan 1, 2006

This paper outlines the position and capabilities of Western Canada's bituminous coal industry, and indicates the increasing importance of Japan as an export market. The use of coal in Japan is reviewed, especially as regards future trends, and an appraisal is made of Canadian coal in comparison with domestic Japanese coal and imports from other countries. The importance of maintaining a solid nucleous within the Canadian bituminous coal industry is emphasized. I N RECENT years, Japan has emerged as a valuable market for Canadian exports. The first major product exported in volume to Japan was wheat, which has become very successfully established in Japanese markets. Following this, iron ore gradually found a market in Japan, with exports usually based on long-term contracts. This iron ore was produced entirely in British Columbia In 1958, the Western Canadian bituminous coal industry -jointly with the Dominion Coal Board -sent an official mission to Japan to investigate the

Jan 1, 1964

By Chikao Nishiwaki

INTRODUCTION The Japanese dependency for mineral raw materials from foreign sources increased rapidly within the 20 years since the Korean war. During this 20 year period Japan has attempted to industrialize and develop her economy while depending mostly on heavy import of nearly all kinds of mineral raw materials. She has fabricated them using energy generated mostly by mineral fuel that are also imported. Fabricated goods are either used domestically to accelerate more fabrication industry or exported after adding more refinement or fabrication. In this paper iron ore as a major raw material for the Iron and Steel industry, three major base metals, copper, zinc and lead, and petroleum as a major energy source have been selected as examples to represent the general features of various kinds of mineral raw materials that are imported. Among other important mineral commodities for which Japan dependa upon foreign sources are: Aluminium, nickel and cobalt, potash and phosphorous 100 percent dependent and tin, tungusten, chromium and molybdenum over 95 percent dependent. IRON ORE Statistics for the important iron and steel raw materials, namely iron ore, coal and scrap iron are shown in Tables 1, 2 and Fig. 1. Iron ore is by far the most important and basic among these three commodities. There has been practically no steel or iron imported as a metal into Japan during this period. Iron ore, including aggregate such as pellets, and metallurgical coal are mostly transported in large ore cargo boats to the port where very efficient port facilities unload them directly at the steel mill site. As a result

Jan 1, 1976

By Dario Libano, Luis Carlos Tenuta, Juliano Penteado

"Subway Line Number 4 is one of the newest additions to the Rio de Janeiro subway network. Built for the 2016 Olympic Games, the 16 km (10 mi) subway line connects the south of the city, with the famous beaches Copacabana and Ipanema, to Barra da Tijuca, west of the city, where the Olympic Village and Park are located. This new line, which is estimated to cost USD 2.2 billion, is composed of six new stations: Jardim Oceanico, São Conrado, Gavea, Antero de Quintal, Jardim de Alah (JA) and Nossa Senhora da Paz Station.Brasfond participated in the construction of foundations and retaining structures for all the stations, and each presented unique challenges. This is not surprising considering the difficulties present in a highly-dense urban environment including utilities, nearby buildings, traffic limitations and noise.Of all the stations, JA Station was the most challenging to construct. It was located in the middle of an avenue between residential high rises supported on shallow foundations as well as below sea level in sands with high groundwater. The other five stations were located in small parks and squares, with no buildings in the immediate proximity.The interaction between designer, owner, and the general and foundation contractors during execution was key in safely reducing the construction schedule. This was significant given the unforeseen construction delays the client, Linha 4 Sul JV, faced due to permitting, utility and traffic relocation so that the owner could fulfill their final goal: making the line operational by the Olympic Games. The GeologyGeologically, the state of Rio de Janeiro is formed by Pre- Cambrian crystalline basement rock. Its geological formation is very old and comprises two major orogenic cycles, a Mid-Precambrian formation, called “Transamazonian” (Proterozoic Era), and an Upper-Precambrian to Cambrian called “Brasiliano” (Proterozoic-Paleozoic). The soil structure of the city of Rio de Janeiro is represented by a core of crystalline rocks, usually granite-gneiss, covered with a layer of residual soil and/or partially weathered rock.JA Station is located in a Rio de Janeiro neighborhood called Ipanema, between the Atlantic Ocean and Lagoon Rodrigo de Freitas. Local geology is composed of a superficial soil, consisting of medium to coarse grained sands. Top of rock varied significantly from 20 m (66 ft) deep on one side of the station to 33 m (108 ft) on the other. Water is at a depth of 3 m (10 ft)."

Jan 1, 2016

Formation of either sodium jarosite or lead jarosite from concentrated chloride solutions containing small concentrations of sulphate has been demonstrated. Sodium jarosite is precipitated at 95-100°C from FeC13-FeCI2-NaCI-PbCI2 solutions to which was added Na2SO4 or Li2SO4 in amounts greater than 0.05 M. In the absence of alkali metal ions capable of forming jarosites, lead jarosite was precipitated from either FeCI3-PbCI2 or FeCI3-FeCI2-LiCI-PbCI2 solutions to which had been added small amounts of sulphate. Many of the factors affecting jarosite precipitation from chloride solution have been elucidated, and the most critical were sulphate concentration and initial pH. Concentrations of HCI in excess of O. I M essentially suppressed the production of jarosite in chloride media. Alkali jarosite, precipitated in the presence of dissolved lead, incorporates a small amount of this metal into the alkali jarosite lattice. Small but significant amounts of copper can also be incorporated into alkali jarosite and the amount is further increased in the presence of lead. Other divalent base metals such as Zn, Cd or Ni are not significantly precipitated. Sulphate control in either FeCI3 or FeCl3-NaCI leaching systems could likely be maintained by jarosite precipitation provided that the acid concentration of the solution was low.

Jan 1, 1981

By P. Maraboutis

Iron removal by precipitation as jarosite from Fe-Ni-Co sulfate solutions, (synthetic or real, resulting from laterites leaching) has been investigated. Precipitation was carried out at 95 C, and at an initial pH 1.6, which was either kept constant with CaCO3 or Li2CO3 additions, or left to drift with the evolution of the reaction to lower values. The precipitation of K-, NH4- and Na- jarosite was initially examined using synthetic solutions. In all cases, hydronium ions were incorporated into the precipitate as well. Residual iron in solution was lower (0.2-1 g/1) and equilibrium was achieved faster (within 4-8 h) when precipitating K¬jarosite at constant pH, using CaCO3 for neutralization. Nickel and cobalt losses were small. Na- jarosite precipitation was also studied from real solutions with high initial iron content, under constant pH=1.5, controlled with CaCO3 additions, and it was shown that low residual iron concentration in solution (0.3-0.5 g/1) can be achieved again, with relatively small nickel and cobalt losses. The thickening and filtration characteristics of the precipitates were excellent in all cases examined.

Jan 1, 1988

By F. Elgersma

A high purity electrolysis solution is essential for hydrometallurgical zinc winning processes. For this reason ferric iron containing compounds such as jarosite are precipitated as iron and impurity collector during the calcine leaching. Jarosite thus forms a chemical waste and creates environmental problems. This research contributes to the development of a wet jarosite treatment process, where less contaminated jarosite is produced which can act as an iron source. The present work studies jarosite precipitation kinetics and the uptake of zinc cations in batch and continuous experiments. The distribution coefficient for zinc in continuous experiments is constant for a wide ratio of zinc over ferric ions in the solution. Addition of NH, + ions in batch experiments accelerates the conversion rate equivalent to the driving force increment. Addition of 50,2-ions above the stoichiometric ratio increases the conversion rate less then could be expected from the increase in the estimated driving force. Zinc ions tend to retard the conversion rate. An increasing reaction temperature increases the conversion rate. Below 75 ?C the conversion rate approximates zero.

Jan 1, 1990

By A. G. Mayton

Vehicle vibration exposure has been linked to chronic back pain and low back symptoms among agricultural tractor drivers. The objectives of this study by the National Institute for Occupational Safety and Health (NIOSH) were to assess driver whole body vibration (WBV) exposures and recommend interventions to reduce the risk of back related injuries, particularly relative to vehicle jarring/jolting (the transient mechanical shock components of WBV). The methodology included collecting, from two independent samples, ?eld data and health and work history data of farm equipment operators. Data were collected during mowing, raking, baling, chiseling, tilling, and road travel for different model tractors. Spraying using a sprayer and shrub removal with a skid steer loader were also included. Based on ISO 2631 (1985), the American Conference of Governmental Industrial Hygienists, threshold limit values, presents 0.5 m/s2 as the action level recommended by the Commission of European Communities for overall weighted total RMS acceleration (vector sum for axes x, y, and z) [ACGIH, 2006. Threshold limit values and biological exposure indices. Cincinnati, OH]. WBV measured at the operator/seat interface exceeded this action level. The roughest rides and highest vector sum accelerations occurred with small utility tractor mowers (3.3 and 2.8 m/s2) and a skid steer loader (1.7 m/s2). Major ?ndings from health and work history data showed 96% of participants reported having to bend or twist their necks, although 24% reported neck symptoms. Sixty four percent of participating operators reported experiencing back symptoms (e.g., pain, aching, stiffness, etc.). Recommendations included: specifying a seat that ??better?? isolates operators from jars/jolts with new tractor purchases; maintaining the seat/seat suspension and replacing worn or damaged cushions with NIOSH tested viscoelastic foam padding; using larger diameter tires with radial ply instead of bias ply construction, particularly on small utility tractor mowers, to aid in attenuating ride ??roughness??; using a swivel seat to reduce the stress on the neck from bending or twisting; and improving efforts to educate owner/operators of the adverse effects of WBV exposures. Since the data presented in this paper were collected from two independent samples, the authors were unable to draw any correlations or etiological inferences from the study. However, results were compared and contrasted with other studies which included similar vibration measurements in agriculture.

Jan 1, 2008

In a previous paper the writer dealt -with the jasper bar formations and their relationship to the structural geology of older pre-Cambrian rocks in the goldfields districts of Western Australia (24). He has pointed out in this ahd other papers that jasper bars, or banded iron formations, banded hematite or ,magnetite quartzites, jaspilites and related banded ferruginous or non-ferruginous cherts, occur in abundan'ce in the Older Greenstone Series of Western Australia (22), (24), (26). They are considered to represent special forms of banded ferruginous sediments, and are usually fpund in the field interbedded with more or less metamorphosed pasaltic 01' andesitic lavas and tuffs, now amphibolites, together with occasional thin bands of normal pelitic sediments, which go to make up a large proportion of the Older Greenstones in thfs State (26).Great thicknesses of fiat-bedded ]:landed ferruginous cherts are also found associated with cherty' carbonate rocks; quartzites, shales and thin-bedded dolomite whicIi constit'ute the Nullagine (Pl'oterozoic) system in the northwest of Western Australia. In the Hamersley Range district these banded ferruginous chert beds are the hosts of important deposits of blue amphibole asbestos.In the paper mentioned above brief reference was> made to the importance, of geological structure in relation to economic geology, particularly in the goldfields regions of Western Australia, and it was shown that jasper bars may have an important role in the study of 'the structural geology of many of these regions. Of possibly more immediate economic importance is the part that these rocks play, both directly and indirectly, as host rocks for mineral deposits-the chief of Which are gold, iron ores, blue asbestos, and manganese ores. The blue asbestos bearing banded iron formations mentioned above are confined to the younger pre-Cambrian Nullagine formations. They have been described in detail elsewhere (23). In this paper it is proposed to discuss the economic geology of the jasper bars found in the older pre-Cambrian series.The jasper 'bars have in themselves little or no intrinsic value except perhaps some of the more highly coloured and banded varieties which may be utilised for ornamental and decorative purposes. Probably the best known of such varieties is the so-called "marble bar;" a belt of, strikingly coloured banded chert occurring just south and west of the famous town of that name (see Fig. 1t). This consists of a hard, very fine, even-grained rock with alternate individual stripes varying from the thickness of a sheet of paper up to an inch or more in width, and ranging in colour from clear white to yellow, from various shades of pink to brilliant...

Jan 1, 1943

By Gieskieng, D. H.

Published tables of jaw crusher capacities are compiled for the most part from field performance data, interspersed with interpolations, extrapolations, various safety factors, and other modifications. Such a table attempts to balance and equalize field data from widely different materials, with differences of crushability, efficiency of feeding, sizing of the feed, and so on. The tests described in this paper were undertaken with the objectives of checking previously reported capacities; of studying the effects of various factors upon the capacity, including jaw plate curvature; and, if possible, of deriving a general capacity equation. Such an equation has been derived from the data obtained in these tests. It is given together with factors for its use. While more accuracy than is usually required may be obtained by careful application of the equation, it is of simple form and provides a convenient reference plane upon which the potential capacity of various crushers may be compared, and with which operating adjustments may be made on existing installations. The principal deviation in these tests from the usual approach consists of a laboratory technique which has been developed for the production of selected

Jan 1, 1949

By S. C. Westerfeld

The original patent for the gyratory crusher was granted to Philetus W. Gates in 1881. This first crusher was used by the Buffalo Cement Co. At the time these early gyratory crushers were developed all mining and quarrying, either underground or open pit, was done by hand; tonnages generally were small and product specifications simple and liberal. Likewise plants were small and demands for small product sizes practically nonexistent. In addition to substantial amounts of hand labor, the available material handling equipment was small, simple, and not suited to handling large run of mine ore. Mine can, cable ways, or belt conveyon transporting crushed material to the mill had limited capacity per hour. At the turn of the century the largest Gates crusher, the No. 9, had a receiving opening of 21 x 48 in. with a three-arm spider and a 21 x 80-in. opening with a two-arm spider. The steam shovel began to change the entire picture of open pit quarrying. As a result of the use of steam shovels around 1910 crushers with 48-in. receiving openings were built; thus it can be seen that the basic gyratory crusher was developed prior to World War I. The improvement of the internal combustion engine and the use of pneumatic tires created a new set of operating conditions. Early mines were small, using shrinkage stoping and small mine can. The capacity of material handling was small, limiting the size of the largest piece and the feed rate. Improved material handling resulted in more and more large open pit mines with large shovels and a tremendous increase in the size of off road or mine haul trucks or rail can. Primary gyratory crushers also increased with receiving openings as large as 60 in. and connected hp of 1,000.

Jan 1, 1985

By John C. Stankus

To improve mine roof bolt performance, Jennmar Corporation commenced the design and development of a new roof control sys- tem. This new system designated "Insta'l Compression", not only improves safety, but is more cost efficient due to reduced amounts of resin needed per bolt installation. In this paper the research and development of this new system will be outlined. Much of the information presented will be actual test data from various underground operations in Alabama, Kentucky, and Pennsylvania. The development of this system will also cover the design of a new expansion shell, resin compression ring, anti- friction washer, and upgrading of material specifications.

Jan 1, 1990

By Richard Hanke

Tunnel construction on the Brightwater Conveyance System?s East and Central contracts required ground modifications of the existing site soils, comprised of sandy alluvium to very dense glacial till, to assist with both hand-mined and TBM tunneling operations at vertical access shafts. The ground modification program was completed with a modified double fluid jet grouting system to construct continuous overlapping soilcrete columns to depths up to 94-ft below existing grade. This paper presents the sequence and methodology for the ground modification work and capabilities of jet grouting for structural support and groundwater control in the challenging soil profile present at the Brightwater Conveyance System Project.

Jan 1, 2008