Search Documents

By M. X. Huang, Y. Z. Li

The titanium diboride (TiB2)-reinforced steel composite, designed for automotive applications, exhibits a combination of high isotropic Young’s modulus and low density as compared to existing advanced high strength steels (AHSS). The steel-based composite is produced by in situ precipitation of TiB2 particles during eutectic solidification followed by hot rolling, and its microstructure displays a homogeneous distribution of both large primary TiB2 and small eutectic TiB2 particles in the ferrite matrix. Instead of interfacial debonding, particle cracking is the primary mode of damage, revealing very high interfacial strength. To investigate the intrinsic interfacial strength, a hybrid method combining both nanoindentation and finite element analysis (FEA) was used. A micron-sized sample containing a single crystal TiB2 attached to the ferrite matrix was fabricated by focused iron beam (FIB), and was compressed using nanoindentation with a flat indentation tip. By combining the compression and FEA results, the interfacial strength was therefore determined.

Mar 1, 2017

By M. S. Klima, P. T. Luckie

Interfacing new or improved unit operations SUBMODULES with the EXECUTIVE of a macro analysis simulator usually requires modification of the input data. For example, particle processing SUBMODULES that are sufficiently general in nature to provide useful predictions require input data for rather narrow size fractions. Such data is not always available for the EXECUTIVE and must therefore be generated by the SUBMODULE. A successful interface to allow incorporation of a new SUBMODULE for comminution and one for classification in a general stream state flowsheet simulator is presented. The general nature of the SUBMODULES, as well as the logic of expanding and contracting the required data input is discussed.

Jan 1, 1983

By G. Pantazopoulos, A. Vazdirvanidis

In this paper, a failure analysis investigation is presented concerning the intergranular cracking of three different diameter (Ø26.6, Ø10.8, Ø8.5 mm) high strength brass rods which failed after extrusion. Optical, Scanning Electron Microscopy and Electron Backscatter Diffraction are employed in order to reveal the mechanisms and the root causes of the failures. The microstructural characteristics, exhibited by the brass rods, pertaining mainly to phase, grain structure, size and distribution of intermetallic particles, are considered to exert a detrimental effect, impairing the mechanical properties, facilitating the environmentally-induced degradation and assisting the occurrence of brittle fractures. Revision of preheating and extrusion conditions could be further implemented in order to minimize the risk of such failure in the future.

Mar 1, 2018

By Alden B. Carpenter

Oil-field brines have been collected and analyzed from Jurassic and Cretaceous rocks in the Mississippi Salt Dome Basin, from Jurassic and Lower Cretaceous rocks, southwestern Arkansas, and from Ordovician and Silurian rocks, southern Michigan. All of these brines are genetically related to evaporites and appear to be brines expelled from halite-bearing rocks, presumably during compaction. The brines in rocks closest to the halite-bearing rocks are uniformly low in lead and zinc suggesting that the metals in metal-rich brines are not acquired within evaporite sequences. The metals in metal- rich brines in Mississippi and in Russia appear to be derived from red beds and may have been originally associated with ferric iron oxyhydroxides. Reduction of these compounds by migrating hydrocarbons appears to release lead and zinc to the associated brines accompanied by the fomation of authigenic ankerite.

Jan 1, 1979

By Brian Hawkins, David Bradley, Rachel Gooding, Lucas Rodriguez, Patrick Wilson, Kevin Wegman, Dhruv Mittal

To better protect the nation and inform difficult defense and preparedness decisions, the Department of Homeland Security (DHS) is performing a probabilistic risk assessment of explosive terrorism risk to the US homeland. After assessing existing models against requirements, well-developed mathematical descriptions and algorithms associated with explosives hazards were combined with probabilistic modeling techniques used in DHS chemical, biological, radiological, and nuclear (CBRN) terrorism risk assessments to create a suitable interior explosive consequence model for assessing the impact to human health.

Jan 1, 2018

By William E. Lardner

Interlocking caisson walls developed from conventional "soldier pile and lagging" shoring. In the latter, the soldier piles receive directly most of the soil load. Natural arches form in the soil behind the shoring; the lagging supports little more than the segment of soil inside the arch. Fig. 1: A typical layout of a lagged wall [ ] Fig. 2: A typical layout of an interlocking caisson wall [ ]

Jan 1, 1987

By Marc Dondelinger

Interlocking H sections with deep webs and high section modulus are being used for cofferdams and shore enclosures where pressures are excessive. The H sections can be as much as a meter deep; they can be used as continuous interlocked wall. A steel saving alternate is spacing the H and driving deep for stability then filling between with shorter interlocking sheet piles. Templates provide for exact positioning.

Jan 1, 1985

If it had not been for the almost unbelievable adventures that came before and after, the last ten months of 19 15 would have been exciting enough for anyone. As it was they were a cheerful interlude. I spent most of the time on our Warren operations catching up on a lot of underground work and visiting Ajo every few weeks to see if my Chuquicamata visit might help solve the New Cornelia problem. While the difficulties were finally solved, at times they seemed almost hopeless. About all I could do to help was to make sure that the ore sent to the pilot plants represented the average ore that must be treated in the final 5000 tpd mill. Dr. Ricketts and John Greenway worked tirelessly with the best consulting advice they could obtain. Credit for the final success was due chiefly to their efforts. Since our old group had given up its "Merry Widow" home in Warren, a few of us got rooms in the company-built Cole Building over the Warren grocery store. This included Jim Lewis, Roy Mitchell, Steve Landon, Paul Stevens, and Hubert d'Autremont who came from Duluth to join our legal staff. Later we rented a small house two blocks from the Calumet and Arizona office. With the now flourishing country club only a 10-min walk away, and an electric car running to it every half hour or so, we were able to give parties in return for the hospitality of our friends. One of the most pleasant episodes came by luck a few days after I got back from Chile. Chester Congdon, a leading director in Calumet and Arizona, with his wife and their daughters, Elizabeth and Helen, spent a couple of days at the Greenway house before making an auto- mobile trip across the desert from Tucson to Ajo. At the same time I arranged to examine the small but rich Bush and Baxter copper mine a few miles from Tucson. At a party in Warren we found we would all be staying at the Santa Rita Hotel in Tucson, and I took my South

Jan 1, 1976

By Oscar A. Glaeser

MINE VENTILATION is an important factor in mine maintenance as well as having direct bearing on labor efficiency. Effective ventilation systems are costly, especially those for the deeper mines, but with intelligent direction the worth of a system is usually greater than its cost. In most mines using mechanical ventilation, and practically all deep mines, it has been found beneficial to equipment, timber, and the ground, to run the fan or fans continuously even though production has been curtailed or entirely suspended. Therefore, economies in ventilation may be overlooked when general cost reductions are necessary. The operating costs of a well-designed ventilation system should be capable of reduction during periods of curtailed or suspended operations. A mine that is ventilated by splits, or that can be sectionized, can reduce its fan-power costs considerably, and provisional divisions can sometimes be made in other mines, in which the air is ordinarily coursed through all the workings, without harmful effects.

Jan 1, 1932

Tyre costs constitute 20-40 per cent of the operating cost of large haulage trucks, and tyre pressure maintenance is an important factor in minimizing costs.In the past, control over the hot (built-up) pressures of earthmover tyres has been inaccurate and inconsistent because it has not been possible, in a practical way, to measure the tyre's contained air temperature.A method for measuring this contained air temperature has now been devised using a bi-metallic probe thermometer inserted through the valve stem. Using these measurements in conjunction with a pressuretemperaturechart drawn up using the general gas equation, very accurate control over hot tyre pressures is now possible.

Jan 1, 1979

By C. Ringas

Pipelines are used extensively in industry to convey various products. Internal corrosion of pipelines can lead to perforation and leakage of the product. A growing problem, not often accurately recognized, is internal corrosion of pipelines caused by bacteria. Microbiologically-induced corrosion (MIC) refers to corrosion caused by a variety of micro-organisms. This form of corrosion is not widely recognized in many industries, although it is widespread and causes many corrosion problems in pipelines, both internal and external. Sulphate-reducing bacteria (SRB) are responsible for the bulk of the corrosion problems caused by MIC. Corrosion caused by SRB is found extensively in water pipelines conveying raw, potable and waste water, as well as in pipelines conveying slurries. This problem also occurs in pipelines conveying crude oil. This paper describes internal corrosion problems of slurry pipelines caused by bacteria and outlines mitigation methods to improve slurry pipeline integrity, thereby extending the life of such pipeline

Jan 1, 2007

By Lin Li, Wen Shi, Hua Wang

"Specimens of the ultra-low carbon bake hardening steel were soaked for 1 min to 5 min, and then cooled by water quenching. The internal friction experiments were carried out to detect the spectra of the specimens. Results show that Snoek peaks are present in all the specimens, however, an obvious Snoek-Koster peak is found only in the 5 min-annealed specimen. Besides, tensile results indicate that the bake hardening values increase with the annealing time prolonging from 1 min to 3 min, but decrease as the annealing time prolongs further to 5 min. The solute distributions in the specimens were characterized by three dimensional atom probe. Some segregated C and V are found in the 1 min-annealed specimen, and the C and V contents decrease as annealing time prolongs to 5 min.1. IntroductionAs an excellent member of automotive body panel materials, various types of bake hardening (BH) steels have been developed since 1980s. Bake hardening property, as one of the most important mechanical properties, has been studied by many researchers [ 1-5]. As is known, BH phenomenon is generally controlled by the interaction between solute C and dislocations. The Snoek peak of internal friction (IF) is very popular in the investigation of solute C [6-9]. However, result of internal friction cannot suggest the distribution pattern of solute C as well as its influence on BH phenomenon.Three dimensional atom probe (3DAP) can diagnose solute element atoms as well as nano-sized precipitates, and it is the only instrument that currently can identify the identities of individual atoms in a material and measure their spatial coordinates with the resolution close to 0.3 nm [10]. There have been a number of studies about using 3DAP to detect solute elements as well as nanometer sized precipitates [11-19]. For example, Hono et al. [16] used 3DAP to determine the solute elements in an age-hardened Mg-Ca-Zn alloy, and they also obtained the distribution patterns of the observed elements."

Jan 1, 2011

By L. E. Beverage, K. L. Johnston

This paper will address methods for minimizing liability and protecting materials from disclosure as result of self- evaluative audits and internal investigations. Specifically, the paper will cover the role of counsel in the investigative process and how best to design and conduct internal investigations to minimize the development of problematic material and disclosure of information. The paper will also address the extent of privileges that may be relied upon to protect materials and information from disclosure. These include the attorney-client privilege, the self-critical analysis privilege, and the attorney work product privilege. These privileges are qualified and understanding the limits of their coverage is essential to minimizing liability.

Jan 1, 2001

By Rajib K. Mohapatra, K. Vizaya Kumar

In any manufacturing organization internal logistics plays a vital role in improving and maintaining the productivity. In Ferro Alloys manufacturing organization where there is huge input of raw material in terms of ore, reductants and variety of fluxes amounting to about four times of the mass of alloy produced need to be handled from yard to furnaces , internal logistics requires utmost attention. Any deviation or mismatch between stock and requirement will affect furnace operation. Though the activities are being outsourced by most of the organization, these require close monitoring. This communication presents an optimization model which can work as a ready reference for the manager to decide upon the material quantity and the furnace to be fed with an objective of minimizing the cost of handling and zero production loss.

Jan 1, 2007

By A. H. Grobe, F. N. Rhines

AT elevated temperatures the oxide of silver is unstable in the air at atmospheric pressure, consequently no external oxide scale forms upon pure silver under conditions of high-temperature annealing When small quantities of certain alloying elements are present in the silver, the formation of a thin external scale is possible' and in addition there may form a subscale composed of the oxide of the solute element precipitated within the body of the silver Norbury2 and Leroux and Raub3 have reported internal oxidation (subscale formation) in alloys of silver with 2, 7 5, and 30 per cent of copper The presence of the subscale is believed to be responsible, at least in part, for the objectionable "fire mark" in Sterling silver' Several other alloys of silver, after oxidizing heat-treatments, are known to exhibit undesirable polishing characteristics that may be the result of internal oxidation Except for the absence of an external scale of silver oxide, it is to be anticipated that silver alloys will prove to be very similar in their oxidation behavior to the alloys of copper, the oxidation characteristics of which have been studied in some detail 5,6 The present research confirms this anticipation The oxidation of a series of 20 dilute alloys of silver has been studied metallographically, some types of subscale not encountered among the copper alloys have been found Instances of internal oxidation in alloys of most of the metals of the I-b and VIII groups of the periodic system are on record, but evidence of this type of oxidation in alloys of the metals of the intermediate groups is lacking A number of the metals of the intermediate group, among them cadmium, lead, tin, and zinc, appear to provide the conditions essential to subscale formation, i e , they form oxides with a relatively low negative free energy of formation, they dissolve other metals that form more stable oxides, and, presumably, oxygen will diffuse through them In a study of 4o alloys of these white metals only a few cases of internal oxidation have been found The probable reasons for this difference in behavior will be discussed presently EXPERIMENTAL PROCEDURE Silver -The silver alloys employed in the oxidation studies were prepared in heats of 30 grams each from high-purity silver (99 993 per cent Ag)* and the purest avail-

Jan 1, 1942

By J. D. Miller

Flotation chemists have long sought to unravel the mechanisms of carboxylate collector adsorption by semi-soluble salt minerals. In particular, the adsorption density of adsorbed carboxylates, adsorption kinetics, speciation (chemisorbed, physisorbed), orientation, and conformation are of interest. Given the importance of these phenomena in establishing the hydrophobic state at a mineral surface, in-situ surface spectroscopy studies certainly are justified. Such measurements traditionally have been difficult to perform. However, beginning in the late 1980s, a Fourier transform infrared (FTIR) spectroscopic technique was developed that has allowed for the acquisition of a wealth of detailed information concerning carboxyiate adsorption in semi-soluble salt flotation systems. The technique, internal rejection spectroscopy using single-crystal internal reflection elements, is reviewed, as it applies to semi-soluble salt flotation systems.

Jan 1, 1999

By M. L. Jeremic

"The syngenetic and epigenetic mechanics of sedimentation and deformation of coal seams resulted in various types of internal structure, as listed below:TYPE I-massive structure with evenly distributed coal constituencies of integrated mechanical properties.TYPE II-broad-banded structure, with bright and dull coal bands of differential mechanical properties.TYPE III-heterogeneous structure, with sheared coal bands and partings of sectional mechanical properties.TYPE IV-contortional structure, with refolded coal layers and deteriorated mechanical properties.TYPE V-porous structure of orogenically crushed and pulverized coal, with disintegrated mechanical properties.The study suggests criteria for the estimation of coal seam internal structure (gamma-gamma density log and cracks density log), which might be related to the evaluation of strata stability and coal mineability.IntroductionIt is common knowledge that coal seams have various internal structures due to different syngenetic and epigenetic events. Investigations of the internal structure of coal seams have been carried out in the coal fields of Western Canada, as follows: geological field studies of coal-bearing strata;?,geophysical borehole surveying studies;?,geological borehole logging and crack density;?,underground phenomenological studies of mine structure;?,chemical coal analysis; and?,mechanical testing of coal samples.These investigations eliminated a large number of criteria previously established for the estimation of coal seam internal structure and indicated that, from an engineering point of view, only two of them are sufficient:(I) density of seam profile (inferred from gamma-gamma log);(2) density of crack s (inferred from geological log).On the basis of these criteria, five main structural types of coal seams have been classified, which might be related to mechanics of deformation and ' failure of mine structures."

Jan 1, 1982

By Q Wang

Net present value (NPV) has been the main criterion in mining project evaluation and production plan optimisation. It is a common practice in NPV calculations to take into account only the tangible cost items in the corporate accounting system. The costs incurred due to damage to the local ecosystem and environment are left out and treated as externalities. Such practice on the one hand underestimates the total cost of a mining operation and, on the other hand, ignores the difference in ecological/environmental impacts between different mine plan alternatives. This paper attempts to measure the ecological costs of mining and to incorporate such costs into the evaluation scheme in mining project evaluation and mine planning. The ecological costs of mining are estimated based on the areas and types of land (eg forest land, grazing land, crop land) damaged by mining activities and the carbon emission from fossil fuel consumption. For the land areas (and their associated ecosystems) directly damaged by mining activities, the ecological costs are measured by the prevention and restoration costs, the lost values of eco-services of the damaged land, including bio-product production, soil erosion control, water run-off control, oxygen release, air pollutant absorption and formation of soil nutrients. The ecological cost of carbon emission from the energy consumption of a mining operation is measured by the cost of cultivating the equivalent forest land required to uptake the emitted carbon. A case study on a large-scale open pit mining project is presented to demonstrate the influence of ecological costs on the mine planning outcome.

Sep 26, 2011

By Hokuichiro Ohmachi

INTRODUCTION Metallic minerals have been formed only through complex geologic processes which took place at certain stages of the earth's histrory. Their concentration, abundance, and distribution are, therefore, restricted geologically, and very small in global scale. Ore is a mineral deposit or mineral concentration from which metals can be economically extracted by the contemporaneous technology. By this definition, several factors should be considered before any mineral deposit is regarded as an ore. The grade of mineral concentration and the scale of the reserve are most important. Demand for the metal and its price are the other factors. Advancement of technology in mining and extraction are also vital. Copper, for example, is now commonly extracted from the ores containing less than 0.3% of the metal. However, in the 1700's the common minerable grade was about 13%, and in the 1900's between 5 to 2.5%. This decrease in minerable grade is a function of not only the demand for copper, but also technological progress in mining and metal extraction in this case. Availability of ores has recently been subject to political factors, which were not the primary concern in the past. The petroleum of the Middle East is the prominent example. The metallic minerals are classified into three categories. The first one is the minerals free from these factors mentioned above. Iron and manganese belong to this category. The second category include aluminum, copper, nickel, cobalt, titanium, lead and zinc. These metals can be provided by the future progress in technology which enables the use of lower grade deposits. The third one represents the metals whose occurrence is geologically limited, and, thus, subject to the political factors. Niobium and tantalium are the example. In this article, I discuss these minerals in detail to give an outline of the factors which brought their concentration, distribution and availability. SELECTED MINERAL CONCENTRATIONS Iron Major iron ore deposits are the features of the relics of ancient continental crusts. They are found in all the continents where the Precambrian rocks expose. They do not occur in the oldest rocks (3,000my old) nor in the youngest ones (600my old). They are sedimentary rocks, normally, exhibiting alternations of bands of iron oxides (magnetite and hematite) or iron silicates (especially greenalite), and bands of silica, variously described as jasper, quartzite and chert. The best known banded iron ore deposits exist in the Lake Superior region of the North America, and their distribution extends at intervals to Labrador of Canada. Other examples occur in the U.S.S.R. Brazil, Venezela, India, the mainland China, and southern and western Africa (Liberia and Guines) (Table 1). Recently large deposits have been discovered in the Hammersley region of the western Australia, and northern and central region of Brazil. These ore deposits were originally formed in shallow seas where simple but abundant life existed. After the deposition, enrichment processes , related to tropical weathering, have brought about wholesale removal of silica to produce the deposits of best quality. Ores with 50-60% iron represent the best products in the Precambrian fields. Since local reserves of this high grade ores approach to exhaustion, benefication processes have been used effectively to upgrade much leaner ores (for example, taconite with 20-25% iron in Minesota, U.S.A.). There are two other types of iron deposits. Ironstone, a sedimentary rock containing goethite, chamosite and siderite, first appeared in early Paleozoic times in the stratigraphic record, and reached its Zenith in the Jurassic. Similar bedded iron deposits are found in the belt from the Cleveland Hills to Oxford in England, and in the "minette" oolitic ores of Alsace-Lorraine in Luxenburg and France. The iron content of these ironstones seldom exceed 30%, but they usually contain calcite and are self-fluxing. They also have phosphorous as undesirable impurity. Because of the grade and impurities, they require more fuel than the Precambrian ores. The third type of iron ore is associated with igneous activity and consists of magnetite and some hematite, and apatite. This deposit is believed to be a product of magmatic differenciation. It occurs in Kiruna of Arctic Sweden. The iron ore, therefore, present no global shortage problem. They extend to considerable depths. Their concentration is largest among the metals. If low grades were treated, the resource can be stepped up much substantially. Manganese Manganese is a ferro--alloy metal, thus, essential to the manufacture of sound steel. Manganese comes from manganese oxide and silicate ores. Many minerals contain manganese, but only a few oxides, silicates, and, in some places, carbonates (rhodecrosite) are mined as ore. Types of manganese deposits are bedded, massive,

Jan 1, 1982

By P. S. G. Leon

One of the most difficult areas in concession contracts in resource-rich developing countries is achieving an equitable balance between the interests of investors, host states and, increasingly, mine and near mine communities. While some countries in the Andean region have resorted to outright or creeping expropriation of natural resource contracts under the guise of resource nationalism, others such as the Democratic Republic of the Congo (DRC), have claimed international best practice in the review (and setting aside) of important concession contracts.

Jan 1, 2011