Search Documents

By H. G. Sell, G. W. King

An investigation was made of the lensile proper-ties of recrystallized high-purity tungsten and a W-1 pel ThO2 dispersed-phase alloy over the temperature region of 800° to 2400°C. The thoria addition resulted in a modest strengthening effect over the entire temperature region. A decrease in ductility of both materials occurred above 0.5 Tm which was caused by void formation. Current theories of IT has long been recognized that a second phase of hard particles has a strengthening effect on a pure metal. At low or intermediate temperatures (<0.5 Tm), the strengthening effect is thought to arise mainly from the interaction of dislocations with dispersed particles. Above 0.5 Tm, dynamic recovery processes greatly alter the deformation mechanisms from those simply involving glide, and grain bound- strengthening by a dispersed second phase do not adequately explain the tensile results. Melallographic examination suggests that the improved strength of tire alloy results from the effect of thoria on the mierostructure. Stress-dependent thermally activated processes were found to occur high temperatures. aries may act as sources of weakness rather than strength because of grain boundary sliding. Grain boundary sliding at high temperatures has been postulated to be the primary factor giving rise to the formation of voids or cavities at grain boundaries1-3 which in turn cause premature failure and poor ductility.4 Voids, once formed, can grow by the condensation of vacancies from the equilibrium concentration&apos; or from the excess vacancies produced by the deformation.4,5 The high-temperature tensile properties of unalloyed tungsten have previously been investigated by Sikora and Ha116 and also by Taylor and Boone.7 The purpose of the present work was to investigate

Jan 1, 1965

By D. I. Bardos, A. M. Bardos, Paul A. Beck

The approximate effective silicon radii in ternary Laves phase alloys with transition elements and silicon were found to range between 1.16 and 1.21A, i.e., considerably smaller than the atomic radius calculated for elemental silicon. The atomic radii were found to increase with the size of the transition element atoms in the structure. It has been noted by Aronsson1 that silicon in solid solution in iron, cobalt, and nickel has an effective CN 12 atomic radius of approximately 1.20Å, a value very much smaller than the CN 12 radius of 1.34Å derived from the interatomic distances in elemental silicon.7 The unusually short metal-silicon interatomic distances in transition element monosilicides and disilicides have been also pointed out by various investigators.1 A similar tendency was observed by Nevitt in Cr3O type silicides.2 Recent work on Laves phases in ternary systems of silicon with transition elements4"8 suggested that extensive Laves phase fields may occur in such systems.8 It has been pointed out by Laves7 that the MgCu2 and MgZn2 type structures lend themselves particularly well for the determination of the effective radii of the component atoms. In these AB2 phases the B atoms are arranged in close packed straight lines, and their distances are related in a simple manner to the lattice parameters.8 The present work was undertaken in order to find out whether or not the B transition element in such AB2 Laves phases can be replaced to an appreciable extent by silicon. In cases where extensive substitution proves to be possible, the "average atomic radius for the B site" at various silicon contents was to be determined, and the effective atomic radius of silicon calculated by extrapolation to complete replacement of the B component by silicon. The following ternary systems were studied: Ti-Mn-Si, Ti-Fe-Si, V-Co-Si, V-Ni-Si, Nb-Fe-Si, Nb-Co-Si, Ta-Fe-Si, Ta-Co-Si, and Mo-Fe-Si. In all of these alloy systems, the Laves phase solid solutions were found to extend over a considerable range of silicon content. As previously reported,4"8 in the V-Co-Si, V-Ni-Si, and Mo-Fe-Si ternary systems Laves phases do occur, even though there are no corresponding binary Laves phases. In stabilizing the Laves phase, silicon acts as if it were decreasing the effective electron concentration of the alloy.8 A more detailed study of the boundaries of the Laves phases in the V-Co-Si and V-Ni-Si systems has been made and will be published elsewhere. In both cases, the elongated Laves phase fields extend parallel to the B-Si side of the composition triangle, clearly showing that silicon is substituting for cobalt, respectively, nickel over a wide range of compositions. The binary Laves phases NbCo2 and TaCo2 have the cubic MgCu2-type structure. It was found that, in both ternary systems with silicon, again the MgZn2-type hexagonal Laves phase is stabilized and that this phase extends to high-silicon contents. In each ternary system at least three Laves phase alloys of the composition A(B1_xSix)2 were used, x here denoting the fractional substitution of the B-transition element atoms by silicon. The alloys, listed in Table I, were prepared by arc melting in argon. Each specimen was water quenched after a homogenizing anneal of 3 days at 110(FC, except for the Mo-Fe-Si alloys, which were annealed at 1200°C. Metallographic examination showed that most of the homogenized alloys consisted of a single phase, although some had minor amounts of a second phase, as shown in Table I. X-ray diffraction patterns were prepared using an asymmetrical focusing camera of large resolution and Fe Ka radiation. The patterns were indexed, and the lattice parameters of the hexagonal Laves phases were determined from the available diffraction lines of highest indices: (213), (205), and (313). The lat-

Jan 1, 1963

By J. B. Coher, M. B. Bever

COLD work destroys long-range order, as was first observed by Dehlinger and Graf.1 Dahl2 showed that the mechanical disordering caused by cold work produces changes in those properties that are affected by long-range order. The existence of order has a marked effect on tile manner in which an alloy deforms and therefore on its mechanical properties.L&apos; The relation between order and deformation behavior however, is only beginning to be understood. Seemann and G1ander4 suggested that cold work reduces an ordered alloy to a kind of gruel of antiphase domains. According to Cottrell,5 superdis-locations and pairs of dislocations in a slip plane connected by a strip of anti-phase domain boundary provide deformation mechanisms which do not change the state of order. In general, however, slip may be expected to produce new domain boundaries and destroy order if dislocations move on intersecting planes or cut through existing domain boundaries. The yield strength of an ordered alloy may pass through a maximum with decreasing domain size.5"7 The reduction of domain size resulting from cold work may, therefore, lead to a maximum in strength properties. Flinn8 suggests that dislocations can climb by short-range diffusion during deformation and thus can generate domain boundaries not only on slip planes, but also on other planes which will be those with the lowest domain-boundary energy. It has long been known that the rate of strain hardening of an alloy in the ordered state is larger than in the disordered state.3&apos;9 Also the slip bands in ordered CU3, AU10 and Ni3Mn" are finer than in the disordered alloys. The stress which causes initial yielding in Cu,Au passes through a maximum with decreasing domain size.6&apos;12 A maximum has also been observed in the hardness of ordered Ni3Mn as a function of strain.&apos; These observations suggest, but do not prove, that domain size reduction occurs during deformation. According to Fisher13 slip destroys short-range order and thus the strength of an alloy is related to the degree of short-range order present. Rudman and Averbach14 and Averbach et a1.,15 demonstrated that cold work reduces short-range order in copper-gold and gold-silver alloys. Destruction of long-range and short-range order by cold work implies slip on an appreciable fraction of planes. Yielding of an alloy in which short-range order exists or antiphase domain boundaries are present should be discontinuous because the first dislocations moving across the slip plane meet with the largest resistance.5 Such discontinuous yielding has been observed in CU3AU6,16 and Cuzn.l7 This phenomenon, however, can also be explained by mechanisms not involving order.b The published investigations of the effects of cold work on alloys with long-range or short-range order have not been covered thoroughly in reviews of order-disorder phenomena. These investigations, therefore, will be listed here. They have been concerned with strength properties> 2,3,6,8,9,12,16-21 electrical resistivity,2,4,18,19,21-26: thermoelectric power, magnetic properties,2,18,21,26 and X-ray strain&apos;1,2,14,15,27,28 The slip systems and the appearance of the microstructure after deformation in ordered and disordered alloys have also been investigated. 6.10.ll,l7,23,29,30 The alloys used in these investigations were copper-gold. 1-4,6,9,10,14,16,18 23-26,28,29 copper-zinc. L7. 19. 20,30 nickel-manganese,2 11,21 iron-aluminum. iron-nickel,&apos; copper palladium,4,18,22 gold-silver.4,18,22 and palladium-silver-copper.4 In the work reported here. the changes in properties of polycrystalline Cu3Au were investigated as functions of strain in wire drawing and rolling. Specimens were heat treated before deformation

Jan 1, 1961

By Harry A. Lipsitt, Douglas Y. Wang

A fatigue study in completely reversed axial tension-compression has been perforried on high-purity titanium and on three high-purity alloys of titanium. The alloys each contain approxi7nately 0.75 at. pct of a single interstitial element; carbon, nitrogen, and oxygen, respectivley. The results corroborate a previously published theory which proposed that strain aging under alternating stress was responsible for the fatigue limit behavior of certain alloys. The present data indicate that in these alloys an increasing strain-talline aging effect under alternating stress is provided by oxygen, carbon, and nitrogen, respectively. CURRENT research on the nature of the fatigue limit in metals suggests that the presence of a fatigue limit in metallic materials is a manifestation of strain aging that occurs under alternating stress.lm5 A comprehensive theoretical model based on the above hypothesis has been developed to explain the existence of a fatigue limit.&apos; This model also provides increased insight into several other fatigue phenomena as under stressing, overstressing, and coaxing effects. The theory, as well, provides equal understanding for those cases where no real fatigue limit is observed. Briefly, this theory assumes that the S-N curve for a pure metal is a smooth function of the applied stress, and the effect of adding an element that is soluble (or forms a precipitate) in the pure metal is simply to shift the S-N curve to the right. If the added element confers the power to strain age, the result is a further shift of the S-N curve, this time upward and to the right. Since strain aging is not expected to be a strong function of stress, and since damage per cycle is known to be quite stress dependent, it is to be expected that there will be some limiting lower stress at which the strengthening due to strain aging will balance the damage due to crack propagation. This stress is the fatigue limit. The position of the fatigue-limit knee was thought to be a function of the magnitude of the strain-aging effect on both the finite and infinite life portions of the S-N curve. Although the strain aging hypothesis seems to be reasonably valid for bcc materials,2&apos;6 it needed to be tested for both fcc and cph metals. This report is the first of a series concerning the fatigue-limit behavior of titanium with varying amounts of the interstitial solutes (C, N,, and 4) that are known to cause static strain aging in titanium. Yield-point effects have been reported for polycrys-talline high-purity titanium alloys containing either carbon, nitrogen, or oxygen.7&apos;9 These effects were observed at testing temperatures in the range 100 to 300&apos;. In addition yield-point and strain-aging effects have been reported for single crystals of titanium containing 0.1 wt pct C plus N.&apos; These yield points were observed over a wide temperature range, but no room-temperature aging occurred. Aging at 180&apos; was required to cause the return of the yield point. The magnitude of the yield phenomena in titanium containing interstitials is not expected to be as large as is observed in bcc metals because of several factors. Titanium has a very high chemical affinity for oxygen and nitrogen. The thermodynamic stability of solutions of oxygen or nitrogen in titanium is recognized. Lattice parameter measurements of titanium containing arbon, oxygen,1° or nitrogen" show that the "c" parameter is expanded more than the "a" parameter, but that up to about 2 wt pct this results in an insignificant change of the axial ratio &apos;c/a." Ehrlich" has shown that the sites occupied by interstitial atoms in titanium are spherically symmetrical and therefore a lattice expansion, at a constant c/a ratio, results in a simple dilation of the interstitial site. Such a dilation involving no shear has been shown to react only with edge components of dislocations.13 This causes only a weak pinning action. Shear stresses would be anticipated locally when only one of the two interstitial positions was occupied. The carbon atom will cause a symmetrical distortion of the lattice whereas the oxygen and nitrogen atoms have, in addition, the previously mentioned chemical affinity of titanium for these elements. These factors will result in a considerably smaller reduction of free energy upon the association of interstitial atoms with dislocations, and therefore a much weaker pinning than has been observed for the bcc metals. These considerations would lead to the hypothesis that of the interstitial elements considered here carbon would cause the strongest pinning effect in titanium where the amount of interstitial in solution is constant. This hypothesis will be borne out in the analysis of the present results.

Jan 1, 1962

By F. Seitz

STAFF: Editor, Gerhard Derge Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Managing Editor, James J. Burke THE METALLURGICAL SOCIETY: John Chipman, President; W. R. Hibbard, Jr., Post-President; C. C. Long, Vice-President; T. D. Jones, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: R. Maddin, Chairman; Dennis Carney, J. C. Fulton, J. H. Hollomon, T. B. King, C. C. Long, W. 0. Philbrook, J. D. Sullivan, David Swan, and F.L. Vogel. Review and selection of manuscripts is under the supervisian of the following Publications Committees: Extractive Metallurgy D ivis ion: T. 0. King, Chairman; S. J. Dick inson, R. P. Hermsdorf, R. Schuhmann, Jr., and H. H. Kel logg. Institute of Metals Division: F. L. Vogel, Choirmon; R. L. Smith, Vice Chairman; R.W. Balluffi, J. H. Bachtold, A Servi, C.D.Graham, Jr., C. G. Goetzel, F. E. Joumot, Jr., G. E. Pellissier, Paul Gordon, Jock Washburn, Harold Margol in, A. U. Seybolt, I. R. Kromer, R. A. Meussner, R. W. Guard, M. Harmon, J. N. Hobstetter, Dean Starr, P. Shewmon, R. Gordon, J. 0. Betterton, and E. Morgan. Iron and Steel Division: W. 0. Philbrook, Chairman; F. C. Langenberg, C. W. Sherman, J. Wagstaff, and E. J. Whittenberger. Published bimonthly by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription $20 per year for non-AIME members in United States and North, South, and Central America; $25, foreign; $5 for AlME members. Single copies, $4.00, single copies foreign, $5.00. The AlME is not responsible for any statement made or opinion expressed in its publications . . . Copyright 1959 by the Americon Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AlME New York ... Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts . . .Second class postage paid at New York, N. Y. , ond Ann Arbor, Mich. Volume 215, Number 3

Jan 1, 1960

By J. W. Cunningham, M. J. Stultzman

THE demand for improved materials for high-temperature service has increased during the last few years. Iron,- nickel,- and cobalt-base alloys have been investigated extensively and many alloys with outs&apos;tanding high-temperature strength have been developed. Considerable research has been directed toward improved methods of processing these alloys. The vacuum furnace as a tool for the purification and improved control of high-temperature alloys has been studied extensively and production units are in operation. The research covered by this paper studied the effects of casting in air, vacuum, or argon upon the elevated-temperature properties of two nickel- and two cobalt-base alloys. The alloys investigated were Stellite 31, He 1049, Udimet 500, and Guy Alloy. MELTING AND CASTING PROCEDURES Two heats of each of the four alloys under investigation were melted and investment cast under the following conditions: 1) Stellite 31 was melted and investment cast in air and in vacuum, with an argon atmosphere for pouring. 2) He 1049 was melted and investment cast in air and in vacuum, with an argon atmosphere for pouring. 3) Udimet 500 was melted and investment cast in vacuum with and without additions of zirconium and boron. 4) Guy Alloy was melted and investment cast in vacuum and in argon. The heats were all melted in induction furnaces equipped with preformed magnesia crucibles of 50-lb capacity. The air-melting furnace was powered by a spark-gap converter of 40 kw capacity. The vacuum-melting furnace was powered by a motor-generator set of 100 kw capacity. The argon heat of Guy alloy was melted in the vacuum melting furnace under an argon atmosphere. Virgin materials were used for preparing all heats except the air heats of Stellite 31 and He 1049. The charge for the air heat of Stellite 31 was a commercial blend of shot. The charge for the air heat of He 1049 was Stellite 6 shot plus those virgin materials necessary to give the desired composition. All of the materials used were of the same grade used com-

Jan 1, 1960

By R. H. Frazier, J. M. Hodge, F. W. Boulger

This paper reports the results of studies of the impact properties of quenched and tempered alloy-steel plates as a function of sulfur content. It was found that the impact energy levels decreased continuously as the sulfur content increased and that there was a straight-line relationship between impact energy and sulfur content when plotted on logarithmic coordinates. Cross rolling raised the level of these Lines for transverse tests and lowered the level for logitudinal tests proportionately to the amount of cross rolling. ALTHOUGH it has been generally recognized that, for applications in which notch toughness is critical, the sulfur content of the steels used should be held to a low value, quantitative information on the effect of sulfur on notch toughness has not been available. For such applications, it is a common practice to specify minimum impact values, and in order that these may be met consistently it is important that the steel producer know quantitatively the effect of sulfur on notch toughness so that realistic sulfur content limits can be applied to the steels they produce. In many instances, particularly in flat-rolled products, impact properties are specified in the direction transverse to the principal rolling direction, so that the factors affecting the anisotropy or directionality of impact properties are also of concern to the steel producer. For some applications, furthermore, it is a common practice to increase the sulfur content of steels in order to improve their machinability, and, in such instances, the effect of this practice on notch toughness may often be of concern. This paper reports on an investigation, carried out at Battelle Memorial Institute, designed to furnish this quantitative information on the effect of sulfur on notch toughness and also to furnish further information on the factors affecting the anisotropy of impact properties in wrought heat-treated alloy steels. MATERIALS AND EXPERIMENTAL PROCEDURE The experimental steels were of intended base analysis: 0.30 pct C, 0.80 pct Mn, 0.25 pct Si, 2.5 pct Ni, 0.80 pct Cr, and 0.45 pct Mo. Steels were made with sulfur contents varying from 0.005 to 0.179 pct. The steels were prepared from 600-lb induction-furnace melts. Steels containing 0.020 pct or more sulfur (at meltdown) were melted from a charge of ingot iron (except for one heat): lower-sulfur steels were made from electrolytic iron. The charge consisted of ingot or electrolytic iron, ferrosilicon to give 0.10 pct Si, and ferromanganese to give 0.05 pct Mn. At meltdown, electrolytic nickel, ferromolybdenum, iron phosphide, and pyrite were added followed in sequence by ferrochromium, sili-comanganese, ferrosilicon, and ferromanganese. The slag was then removed and graphite added to give the desired carbon content. Bath temperature was adjusted to 2850°F and, when no other additions were to follow, 2 lb per ton of aluminum was added, immediately before tapping. Compositions of the experimental steels appear in Table I. Analyses are from single determinations, except sulfur which was analyzed in duplicate. A test sample (3 in. in diam by 6 in. long) and a 575-1b ingot were poured from each heat. The test sample was poured in a sand mold; the cooling rates of the test sample and the large ingot were approximately the same. Chemical analysis chips and metal lographic specimens were taken from the test samples. The ingot was 8 in. sq at the base and 9 in. sq at the top. A 5 X 5 X 6-in. sand mold hot top was completely filled in teeming the ingot. After solidification, the mold was stripped from the ingot which cooled to room temperature. Ingots were reheated to 2250"F and rolled to 1.9-in. slabs on a commercial mill. The slabs were box-cooled to room temperature. Sections of the 1.9-in. slabs were heated to 2250°F and rolled on a Battelle laboratory mill according to one of three schedules: 1) rolled straightaway to 0.5-in. plate; 2) rolled straightaway to 1.3-in. thickness, then cross rolled to 0.5-in. plate (29 pct cross rolling); or 3) cross rolled from 1.9-in. to 0.5-in.-thick plate (46 pct cross rolling). The 0.5-in.-straight- or cross-rolled plates were normalized at 1700°F for 1 hr and then water quenched from 1600°F. Plates were then tempered 2 hr at 1240°, 1170°, 1080°, or 860°F to obtain Rockwell C hardness of 25, 30, 35, and 40, respectively. Tempering was followed by quenching to room temperature to avoid temper embrittlement. Slack-quenched plates were isothermally transformed for 26 min at 800°F, quenched, and tempered 2 hr at 1170°F. Pearlitic microstructures were obtained by holding 168 hr at 1200° F, followed by quenching. Charpy V-notch specimens were taken both transverse and longitudinal to the main rolling direction, notched perpendicular to the plate surface, and tested. Slabs and plates which were to be homogenized

Jan 1, 1960

By A. G. Metcalfe, A. Siede

The hardening of annealed copper during fatigue testing appears to be independent of the applied stress and to occur largely within the first 4000 cycles. Copper hardened by fatigue is more resistant to annealing than copper hardened by static means, and softens by a multistage process. Creep studies at 300°C show that copper hardened by fatigue also has greater resistance to creep than statically hardened copper. Some theoretical explanations are discussed. RECENT interest in the behavior of metals subjected to fatigue stems from observations of phenomena which could not be explained by current theories of the structure of metals. In 1953 Bullen et al.l showed that the hardening caused by fatigue at low stresses did not cause severe bending of the lattice as did hardening by static methods. This was later confirmed by Wood, &apos;and Broom and Ham.3 Clarebrough et al4 showed that as the stress level used in fatigue hardening was increased, bending of the lattice was introduced, eventually approaching that of metals deformed by conventional cold-working methods. The type of hardening introduced by fatigue has other interesting characteristics. Kemsley5 showed that copper fractured by fatigue at low stresses resisted annealing as compared to copper hardened an equal amount by static means. The work of Clarebrough etal, shows that the manner of energy release during annealing differs for fatigue-hardened and statically hardened metal in both magnitude and temperature range of release. In addition to hardening of the lattice, fatigue has been shown to cause softening in materials previously hardened by static methods,5 and also in age-hardened alloys.7 The superposition of a small fatigue stress on the static loading of high-temperature alloys has been shown to increase their resistance to creep.&apos; The present work was an attempt to determine the relationship between fatigue hardening, resistance to annealing, and the creep properties of pure copper. EXPERIMENTAL PROGRAM The program described here was designed to answer three questions: 1) Can stress-cycle combinations well below the failure values give significant increases in hardness? 2) Does hardening, under different stress-cycle combinations, give increase resistance to annealing? And if so— 3) Does superior resistance to annealing confer superior creep properties over statically hardened material? Three-quarter hard OFHC copper was annealed in vacuo at 550°C for 1 hr to produce a strain-free material having a fine grain size and uniform hardness. (The standard deviation of the mean hardness of the annealed samples was less than + 1.9 Dpn). Annealing was performed after machining the fatigue specimens so as to avoid work-hardened surfaces. Jigs were used to avoid distortion. The fatigue properties of the annealed copper were determined using an accurately aligned Baldwin-Sonntag SF1-U machine operating at 1800 cycles per min. This limited the minimum number of cycles which could be examined to about 4000 stress reversals. Since failure resulted in specimen damage, hardness increase with number of cycles was measured by testing specimens fatigued to different fractions of the failure values. The results are shown in Fig. 1, and are superimposed on the S-N curve of the copper in Fig. 2. The resistance to annealing of fatigue-hardened material was compared to that of material hardened by uniaxial tensile straining. Specimens hardened to equal values by both methods were progressively annealed for 1 hr at temperature in vacuo. After each annealing treatment the hardness was measured using a Leitz Durimet hardness tester with a 500-g load. At least five tests were made for each hardness determination. The standard deviation for individual specimens varied from 0.26 to 1.48 hardness points. The results are shown in Figs. 3 to 5. The discontinuous nature of the annealing process has been brought out by drawing idealized curves through the data points. This can be justified by the consistency of the results as well as by general agreement with results of Kemsley.5 The creep resistance of fatigue-hardened and

Jan 1, 1960

By G. Krauss, W. Pitsch

The fine structure of the bcc martensite formed in an Fe-33 wt pct ATi single crystal of arrstenite is sho~on by transmission electron microscoPy to consist of combinations of transformation twins, stacking faults, deformation twins, and regular arrays of parallel screw dislocations. These structures constitute evidence for the multiple lattice-invariant deformations which operating during the formation of martensite could produce the real habit-plane scatter measured by a two-surface analysis of the plates formed in the single crystal of this investigation and reported in the literature for other Fe-Ni rnartensites. CRYSTALLOGRAPHIC theories1,2 of martensitic transformation show that the habit plane of martensite in a parent lattice is dependent in part upon an inhomogeneous distortion or lattice-invariant deformation which takes place on a fine scale within a martensite plate during its formation. Several recent theoretical papers3,4 have addressed themselves to an analysis of a wide variety of conceivable lat-tice-invarient deformations and the habit planes which they produce, while experimental investigation have been concerned with either the measurement of habit planes or the description and identification of the martensitic fine structure which reflects the nature of the lattice-invariant deformation operating during transformation. In Fe-Ni alloys with subzero Ms temperatures, the group of alloys with which this paper concerns itself, habit planes have often been found to scatter an amount greater than might be expected from possible experimental errors,5-7 and fine twinning has been identified as a major constituent of the fine structure of martensite.8-11 It has been suggested3,4 that more than one type of invariant shear occurs during martensitic transformation. This possibility has been experimentally supported12,13 by the observation of both dislocation configurations and twinning in a single martensite plate. The purpose of this paper is to report additional evidence for multiple lattice-invariant deformations in martensite and so to account for the real scatter in the habit planes of the martensite plates formed in Fe-Ni alloys. EXPERIMENTAL PROCEDURE The Fe-Ni single crystal was produced by pulling a high-purity iron and nickel charge through a single-crystal vacuum furnace in an alumina crucible. The crystal was double-melted to promote homogeneity and to increase its size by further additions on the second pass. In its final form the crystal was 4 cm in diam and 5 cm long. The nickel and carbon contents were analyzed at 32.9 and 0.006 wt pct, respectively. The austenite of this alloy first transformed to martensite by bursts at about -120°C, and, to preserve as much of the austenite as possible, all transformation was performed just below -120°C. Some observations were made on transformed samples which had been heated for 2 min at 340°C. It is assumed that the features of the martensite of these samples, Figs. 1 and 4, are the same as those of the as-quenched martensite. Orientation of the crystal by X-ray diffraction established 10.735 0.609 0.3161? as the axis of the crystal, an orientation that was checked within 2 deg by neutron diffraction. Further checks by electron diffraction of samples cut normal to the axis confirmed this orientation within the larger limits of error inherent in electron diffraction of thin foils. The X-ray orientation was the one used for the two-surface analysis of the martensite habit planes. A two-surface analysis was performed on the quadrant of the single crystal which had been oriented by both X-ray and neutron-diffraction techniques. Photomicrographs at X50 were made on two surfaces along an edge 2 cm long. Fiducial marks and the fact that many of the plates were almost completely surrounded by retained austenite made good matching of individual plates on two surfaces possible. The habit-plane trace on a surface was taken as the best line parallel to the long axis of a plate. A measure of the accuracy afforded by this criterion was provided by a family of very large plates which appeared at intervals along the entire 2 cm length of the edge. The plates all had habit-plane traces within 2 deg of one another. Many of the plates did not show midribs and, therefore, the use of midribs7 to represent habit-plane traces was not feasible in this investigation. The over-all experimental accuracy is estimated to be better than ±2 deg. Samples for transmission examination in a Siemens Elmiskop I at 100 kv were prepared by cutting 2-mm-thick discs from the single crystal, removing about 0.5 mm by chemical polishing,14 trans-

Jan 1, 1965

By C. H. Li, R. J. Stokes, T. L. Johnson

The effect of alumina particles on the nucleation and growth of cracks through a silver- chloride matrzx has been investigated. It has been found possible to promote fibrous cracking in dispersion-strengthened silver, chloride under notch-impact conditions at temperatures at which silver chloride alone cleaves brittlely The modification) of fracture beIzavzor is thought to be due to the relaxation of hydrostatrc stress beneath a notch by the nucleation of cavities near alumina particles. In recent years, composite or dispersion-strengthened materials have been studied primarily to understand their high resistance to plastic flow particularly at elevated temperatures. Dislocation models have been developed with which it is possible to deduce with fair success the effects of interparticle distance, particle size, temperature, upon yielding and creep behavior.l-4 Much less attention has been paid to the fracture behavior of these materials (with the notable exception of common structural steels) and little is known experimentally about the manner in which inclusions affect the nucleation and growth of cracks through a matrix. Nevertheless a beginning has been made in connection with fibrous cracking in ductile matrices where inclusions appear to play an essential ro1e.5-7 During the severe localized plastic deformation which accompanies necking in a tensile test, cavities are believed to develop at inclusions; these cavities subsequently grow and coalesce by plastic flow until separation is complete. It is of interest to consider whether inclusions can affect fracture behavior under loading conditions which restrict the plasticity of the matrix itself (for example, cleavage under conditions of a high imposed strain rate at low temperatures). It is particularly interesting to study these effects in a solid which shows a spectrum of behavior ranging from fully ductile to semi-brittle behavior. Such a solid is silver chloride whose mechanical behavior depends sensitively upon temperature and strain rate.&apos;," The present paper is concerned with a study of the influence of inclusions (in the form of alumina particles) on the fracture behavior of silver chloride loaded uniaxially at low strain rates at room temper- ature and also under notch impact conditions over a wide range of temperature. In particular, it will be shown that the alumina particles can exert a startling effect on the ductile-brittle transition temperature of notched silver chloride and that the magnitude and nature of the effect depends upon both the quantity of alumina and the shape of the alumina particles. 1. EXPERIMENTAL PROCEDURE 1.1 Materials Used. Silver chloride powder of analytical reagent (AR) quality having an average particle size 6 was supplied by the Mallinckrodt Chemical Works (st. Louis, MO.). Acid washed 900 mesh alumina powder, designated A38-900, was supplied by the Norton Co. (Cambridge, Mass.). This powder was added to silver chloride in two forms: a) the as-received condition in which the individual particles were of random irregular shape; their statistical average size was 7; b) in a condition in which each particle was spherically shaped by a fusion technique. In this case, the statistical average particle size determined with the optical microscope was approximately the same (about 5p) but electron micrographic evidence indicated that many ultra fine particles were present in the spheroidized powder. 1.2 Preparation of Composite Materials. Silver chloride-alumina composites containing 2.5, 5, and 15 pct by volume of alumina were produced by the extrusion of mechanically mixed powders blended in a ball mill for 24 hr at room temperature. The mixtures were compacted at 50,000 psi at room temperature in the form of billets 3/4 in. in diameter and 1 in. long which were then extruded with a 16:l reduction ratio at 370°C through a radius-type steel die having a 5 deg lead-in angle. An extrusion temperature of 370°C was selected to ensure that all composites had sufficient plasticity to be extruded. Apart from this general requirement, the choice was arbitrary. 1.3 Microstructure of Composites. Attempts were made to check the distribution of alumina metallo-graphically by polishing transverse and longitudinal sections of the extruded rod. Specimens were wet-ground to 600 emery paper and lapped successively with 5 and 0.25-p grades of diamond paste. They were etched for 10 sec in 10 pct sodium thiosulfate solution and lightly polished in concentrated ammonium hydroxide. The most effective way to render the alumina particles and grain boundaries visible was to radiate the surface with intense white light to decorate the grain boundaries and the particle-matrix interfaces photolytically.

Jan 1, 1962

By A. A. Bauer

The ?-to-? transformation has been studied in zirconium alloys containing 22 to 70 wt pct U. In this range of compositions the ? phase can be retained by quenching. Transformation to ? occurs by a nucleation-and-growth process. The diffusion of atoms to preferred lattice sites to yield a partially ordered structure apparently controls the rate of reaction. Alpha uranium and a zirconium precipitate from the supersaturated E phase initially formed in alloys outside the equilibrium E phase composition limits. ZIRCONIUM-Uranium alloys have long been of interest for reactor-fuel applications because of the low thermal-neutron cross section of zirconium. Considerable information is available on the various properties and behavior of these alloys1 although there had been a number of areas where information was incomplete. As part of a program to provide more detailed knowledge in these areas, the presently reported investigation was undertaken. The constitutional diagram of the zirconium-uranium system is shown in Fig. 1.&apos; The system is distinguished by a region of complete solid solubility between the body-centered cubic ß-zirconium and ? uranium phases and the existence of an intermediate phase in the vicinity of 50 wt pct U. This intermediate phase, designated as E, is reported3 to have a primitive hexagonal structure with a = 5.03 and c = 3.08A. The structure is partially ordered with zirconium atoms at the 0, 0, 0 position and zirconium and uranium atoms located randomly at the 1/3, 2/3, 1/2, and 2/3, 1/3, 1/2 positions. While the E phase may be nominally designated as of UZr2 stoichio-metry, the random distribution of uranium and zirconium atoms permit a considerable range in composition. Of interest in the research performed were alloys in the range from 20 wt pct (10 at. pct) to 70 wt pct (47 at. pct) U. In this range of compositions the body-centered-cubic ? phase can be retained either completely or partially on quenching. The nature and kinetics of transformation of the ? phase were the subject of study. Proceeding concurrently with the presently reported work was an investigation by Kearns4 which has since been reported. Kearns studied alloys containing 50 to 60 wt pct U prepared from sponge zirconium. While the work reported here is for alloys prepared from crystal-bar zirconium and the techniques of study are to some extent dissimilar to those employed by Kearns, general agreement so far as results and interpretation can be reported. Experimental Techniques—Alloys were prepared and the transformation of the ? phase studied during interrupted-quench and quench-and-temper isothermal heat treatments by means of hardness measurements and X-ray diffraction and metallographic techniques. The isothermal transformation of the ? phase on quenching and tempering was investigated further employing dynamic-modulus measurements. Electrical resistivity and limited Hall coefficient measurements were also obtained as part of the study. Alloy Preparation and Heat Treatment— Alloys containing 15, 20, 22, 30, 40, 45, 50, 55, 60, and 70 wt pct U were prepared from as-reduced uranium and crystal-bar zirconium. The alloys were double arc melted by consumable-electrode are-melting techniques. The final ingots were forged and rolled at temperatures between 790" and 840oC to 1/4-in. rod and 1/8-in. sheet. Chemical analyses of the fabricated alloys were

Jan 1, 1961

By S. Weinig, J. Winter

The grain boundary adsorption of solutes as a function of bulk concentration and solution temperature was studied using internal-frictimz techniques. From the variation of the cor-responding energy of activation for the Phenomenon, the inter-actior2 energy between a solute atom and a high-angle boundary was calculated. Interaction energies in the range of 0.3 ev were obtained, and were used to obtain the actual concentration of solute at the grain boundary. In corroboralory creel, studies the direct grain boundary contribution to the total creep strain was measured. It was found that the interface creep varied with the type and magnitude of the solute adsorbed. Subscribing to the theory of their being energetically favorable sites at the grain boundary for solutes of both Positive and negative size deviations, ternaries were investigated in Which solutes of both types were present. A marked increase in the resistance to grain boundary creep was manifested. THE major difficulty which has been encountered in investigations of the grain boundary segregation of solutes has been the lack of a sufficiently sensitive method of measuring the amount of adsorbed solute at the boundary. For the general case of a high-angle boundary, no direct method of measuring the adsorption at the boundary has been found to date. Internal friction has been used in several studies of grain boundary adsorption1-3 and although it is somewhat indirect, it was demonstrated to have the necessary sensitivity. In this investigation the authors have used internal-friction techniques in conjunction with a study of the grain boundary contribution to the total creep strain. As both parts of the investigation were performed on the same specimens it was possible to combine a highly sensitive technique with a somewhat more direct method in order to obtain information about the adsorption phenomenon. From internal-friction studies the rate of increase of the activation energy was observed to be a function of the difference in size between the solute and solvent atoms. It was proposed that if Gibbs&apos; adsorption isotherm is considered, i.e., where r is the excess solute at the boundary, c is the bulk concentration, and ay/ac is the change in grain boundary energy with bulk concentration, then AH b/ac must vary in the same way as ay/ac and therefore In this way a relative measure of the grain boundary adsorption of solutes is directly obtainable from in-ternal-friction studies. If the previous work in the field of grain boundary adsorption of solutes is examined, certain apparent information is desirable if the phenomenon is to be understood. The most important questions that must be asked are as follows: 1) Is the adsorption of solutes at the grain boundary an equilibrium process? 2) Can the Mott model of the grain boundary be used as a basis of setting up an elastic interaction between the grain boundary and solute atoms? 3) Is it possible to obtain an exact measure of the excess solute at the grain boundary as a function of temperature and bulk concentration rather than merely a relative measure of the adsorption 4) Are the conclusions obtained from an indirect method such as internal-friction studies meaningful in considering gross grain boundary effects such as creep? EXPERIMENTAL PROCEDURE The material used in this investigation was Bureau of Mines "superpurity" titanium (79 Bhn—1500 kg

Jan 1, 1960

By C. J. Osborn

In oral discussion at the Columbus midyear meeting, September 26, 1949, these pertinent questions were asked: Was a satisfactory separation of metal and matte obtained? The matte was quite fluid and in most cases the separation was satisfactory. Were the mattes chlorinated after aging? The mattes were stored in sealed glass mason jars, and chlorina-tion experiments made after standing for several weeks gave satisfactory results. Was ferric chloride volatilized? Most of the iron content of the matte was converted to ferric chloride. However, because of the low chlorination temperatures used (150" to 250°C) the major part of the ferric chloride remained with the residue. Undoubtedly, some ferrous chloride was also formed, because of the reducing conditions within the reaction vessel, but no effort was made to separate it from the ferric chloride. Could the reaction be stopped before making metallic iron? No attempt was ever made to stop the reaction before making metallic iron. Generally, 20 to 60 pct of the iron in the charge was obtained as metallic iron which could be readily separated from the matte. In certain cases, metallic iron was dispersed through the matte in the form of globules, which could be removed by magnetic separation. Could other sulphides, i.e., calcium sulphide or sodium sulphide be used in place of iron sulphide? No other sulphides were investigated. It was felt that titanates of calcium and sodium would be formed should these sulphides be used to replace the pyrite. What were the sulphur volatilization losses during matte smelting? In the course of this laboratory investigation, a rather wide variety of variables was introduced from highly oxidizing to reducing conditions and various ratios of pyrite, rutile, and coke. These and other factors all have a definite bearing on the sulphur losses. In general, the higher the sulphur in the charge the higher were the sulphur losses and the percentage of titanium in the matte decreased. With sulphur additions more nearly the theoretical amount, the sulphur losses averaged approximately 10 to 15 pct. With a higher percentage of sulphur on the charges, the losses were in the order of 15 to 30 pct.

Jan 1, 1951

By C. Land, R. Hultgren

Heat contents of four Cr-Ni alloys were determined in a diphenyl ethev calorimeter. Aside from ferromagnetic effects, Kopp&apos;s law of additivity of heat capacities is approximately fol-lowed, in disagreement with earlier results of A. W. Foster. In 1934 Foster1 reported heat-capacity measurements of dilute solutions of chromium in nickel, primarily as a study of the effect of alloying on the ferromagnetic Curie temperature. He found that, apart from the Curie temperature effect, the general level of heat capacities was reduced 10 pct by the addition of 1 pct Cr; 20 pct by the addition of 2 pct Cr. His measurements of pure nickel essentially agreed with accepted values. These results indicate that small amounts of dissolved chromium cause an increase in the Debye temperature of nickel, presupposing a change of frequency of interatomic bonding vibrations which is much larger than should be expected. If Foster&apos;s results were verified, therefore, they would have important implications for bonding theory. The only other heat-capacity measurements in this system seem to be those of Taylor and Hinton,&apos; who studied anomalies which they attributed to super-lattice formation at 25 at. pct Cr. At temperatures above the anomaly, Taylor and Hinton found heat capacities at this composition were quite normal, approximately obeying Kopp&apos;s law of additivity. EXPERIMENTAL WORK In order to verify or disprove the remarkable results of Foster, the heat contents of four dilute solid solutions of chromiunn in nickel were measured in a diphenyl ether calorimeter. This instrument, described elsewhere,, operates on the principle of the Bunsen ice calorimeter, but uses diphenyl ether as the working substance. Diphenyl ether melts at the convenient temperature of 26.S°C and supplies a more sensitive measure of heat than ice. The hot sample, in an atmosphere of argon, is dropped from a furnace at a measured temperature into a chamber which is surrounded by a mixture of solid and liquid diphenyl ether. The heat from the hot specimen melts some of the solid without chang- ing the temperature of the calorimeter. The amount of solid melted, and therefore the number of calories released by the specimen, is measured from the increase of volume of the mixture, which pushes mercury down a graduated capillary tube. The apparatus has been standardized against the known heat content of pure platinum. Heat loss during the dropping of the specimen was estimated by comparing the heat content of an empty platinum capsule with a solid platinum ball of the same radius and degree of polish of the surface. Repeated tests demonstrate the precision of measurement to be closer than *0.3 pct. Smoothed experimental results are listed in Table I. The tabulated values for pure nickel are taken from kelley, several measurements were made which agreed closely with this tabulation. For chromium, however, no similar agreement was found. The values tabulated were taken from a thorough study of chromium with the diphenyl ether calorimeter which will be published elsewhere.= Suitable plots of the data showed the expected ferromagnetic anomalies in the low-chromium alloys, while the 11 pct alloy shows no ferromagnetic anomaly, but a different, small anomaly below 900°K. This is perhaps the same anomaly found in CrNi, which was once attributed to superlattice formation,&apos; but is probably due to some other cause, such as antifer-

Jan 1, 1960

By C. G. Rhodes, D. Kramer

High-field critical transport current density (J) measurements at 4.2 °K as a Junction of applied magnetic field (H) were made on samples of cold-rolled and annealed columbium with H parallel to J. Microscopic examination of the samples revealed a well-defined planar fiber structure produced by the cold rolling. J was found to he lower when fibers are parallel to the direction of magnetic field penetration than when they are perpendicular. This effect may he a consequence of the interaction of flux movement with fiber boundaries. THE severe changes in microstructure brought about by cold working superconductors leads to profound changes in their superconducting behavior. In particular, the ability of a superconductor to carry a transport current with zero resistance (the maximum value of this current density will be called "J" in the presence of large external magnetic fields (to be referred to as "H") is greatly influenced by the microstructure. In the case of columbium, LeBlanc and Little1 and Autler et a1.2 have observed an increase in J due to cold work. LeBlanc and Little also observed an anisotropy in J in cold-rolled columbium strips, which Hake et al.3-6 have shown to depend upon the angle between H (H ? J) and the rolling plane. An increase in J due to cold work has been found in a variety of high-field superconducting alloys3&apos;4&apos;7-9 as has the anisotropy effect.10 First explanations of why cold work raised J invoked the idea that dislocations carried the high-field supercurrents,8,11 since cold working drastically increases the dislocation density and presumably the number of supercurrent paths. However, recent ideas on the nature of high-field superconductivity together with new experimental evidence reveal that the bulk of certain superconductors can remain superconducting in high fields while carrying high transport currents. These later developments have been discussed by Berlin-court and Hake12 and a comprehensive review has been prepared by Berlincourt.13 According to the ideas of Gorter14 and Anderson,15 one would expect that the influence of microstructure on high-field supercurrent density will depend on tine interaction between microstructure and penetrating flux and on the direction of the Lorentz

Jan 1, 1965

By A. H. Willis

In this paper the results of an exploratory study conducted by personnel of the Knolls Atomic Power Laboratory on 18.6, 22, and 40 wt pct uranium-zirconium alloy will be presented. LARGE power output and long life or endurance from small, compact nuclear reactors require the use of enriched uranium for a fuel material. However, the ability to remove heat from the element, the tolerable fission product concentration, or some physical limitation of the system can limit the allowable fuel enrichment, or the volume of the fuel. In such an event, the fuel-element designer must find a suitable diluent for the uranium. Zirconium is an attractive material for such a purpose as it has good nuclear properties and a low absorption cross section. Because it has a good corrosion resistance in water, zirconium is a suitable cladding and the uranium-zirconium alloy makes a good core material. The alloy has a high thermal conductivity, a low elastic modulus, and a low thermal-expansion coefficient, all of which tend to minimize the thermal stresses in the core. Furthermore, the unirradiated material is reasonably ductile and has adequate strength. DESCRIPTION OF SAMPLES Two types of cylindrical samples were used in this study 1) short, 1/2-to 1-in.-long samples to test the irradiation stability of the alloy and 2) 2-ft-long samples to investigate the resistance of an element to longitudinal deformation. Composite samples having 0.060-to 0.140-in. core diameters and clad with a 0.010-in. thick zirconium jacket were fabricated by coextrusion and by hydrostatic pressure bonding of the cladding to the preformed core material. Both fabrication processes produced the uniform metallurgical core-to-cladding bond which was felt necessary to minimize the uncertainty of the central core temperature. Both consumable-arc and induction-melting techniques were used to melt the uranium-sponge zirconium core alloy. Since a graphite crucible was used in induction-melting this alloy contained more carbon impurity, which resulted in a finer grain size than the arc-melted alloy. The core to cladding interface was uniform in elements coextruded from the fine-grain, induction-melted core material, while those elements fabricated using arc-melted core material had very irregular interfaces because of the coarser grain size. Both cold-worked and heat-treated fuel materials were irradiation tested. Cold-worked alloys were swaged to about a 5 pct final reduction in area without subsequent annealing. The heat-treated alloys were heated to 800°C, held at temperature for 15 min and furnace-cooled to about room temperature. This

Jan 1, 1960

By M. Cohen, D. J. Blickwede

Quantitative observations concerning the carbide phases in high speed steel are of importance for two general reasons: (1) the carbides, being inevitable constituents of the final structure, exert a direct influence on the properties of the steel; and (2) a substantial proportion of the total alloy content is tied-up in the carbides, and hence the extent of their solution on austenitizing governs the composition of the steel matrix. The latter relationship has a vital bearing on the response of the steel to tempering as well as on its performance in subsequent service. Accordingly, in the course of a long-term study of the behavior of high speed steels, the authors were confronted with the problem of securing quantitative data on the carbide phases. The obvious method for acquiring such information is to isolate the car-bides from the steel and subject them to chemical, X ray diffraction and other measurements. There are well-known extraction techniques which involve the chemical or electrolytic solution of the less noble matrix (ferrite, marten-site or austenite), thus leaving a residue of the carbide phases. However, the results obtained must be scrutinized carefully1,2 since the carbides may be affected by the chemical or electrolytic action. It is the purpose of the present paper to describe the experiments leading to an electrolytic-extraction technique for quantitatively isolating the carbides from both I and hardened high speed steel. Particular attention is paid to the amount, as well as the composition, of the carbides so that the matrix analysis becomes ascertainable by subtraction from the overall steel composition. Illustrative results are given for the M-2 grade of tungsten-molybdenum steel. Review of the Literature The chemical method of dissolving the matrix selectively with respect to the carbides makes use of dilute non- oxidizing reagents such as hydrochloric or sulphuric acid. Although this simple procedure has led to the determination of the cementite composition,3,4 it achieved only limited success because of the interaction between the acid and the carbide residue. Some of the carbides may not only be destroyed in this way, but the hydrogen released is likely to remove part of their carbon as hydrocarbon gases. The electrolytic technique of isolating carbides has the advantage of rapidly dissolving the specimen (anode) in the presence of less reactive solutions than are practicable with the chemical method. This reduces the possibility of chemical attack on the carbides, and furthermore, the hydrogen evolved during the electrolysis is released at the cathode which is not in close proximity to the carbides. The common electrolytes adopted for this purpose are hydrochloric and sulphuric acids.5-l1 Aqueous solutions of ferrous salts have also been used.12,13 A considerable advance in experimental technique was introduced by Treje and Benedicks14 who developed a double-compartment cell for electrolytic extraction, the anode and cathode chambers being separated by a porous diaphragm. A solution of 15 pct sodium citrate, 2 pct potassium bromide and 1 pct potassium iodide was selected for the anolyte, while the catholyte consisted of a 10 pct solution of copper sulphate, with copper serving as the cathode. This type of cell has a number of desirable characteristics: 1. The anolyte has a pH value close to 7, at least at the beginning of the run. 2. The iron that dissolves from the anode-specimen forms a water-soluble complex ion with the citrate, thereby preventing the precipitation of iron hydroxide (which would contaminate the carbide residue) despite the neutrality of the solution. 3. Copper deposition instead of hydrogen evolution occurs at the cathode, and this avoids an increasing concentration of hy-droxyl ions which (in an otherwise neutral solution) might cause the precipitation of insoluble hydroxides. 4. Contamination of the anode chamber by copper sulphate is inhibited by the porous diaphragm. Houdremont and coworkers15 applied the above method (with the further refinement of excluding oxygen during the electrolysis, washing and drying) to the extraction of carbides from a series of plain carbon steels after various heat treatments. They had quantitative success only with specimens in the annealed condition, and concluded that the size and shape of the carbide particles play an important role in the isolation process, with large spheroids exhibiting the least tendency to decompose during the electrolysis. Up to the present time, the citrate double-cell has not been used to any extent for isolating the carbides of high alloy steels, apparently on the grounds that the complex carbides are more resistant than cementite to attack in the simpler acid electrolytes. In particular, Bain and Grossmann7 and Gulyaev10.10a have employed the hydrochloric acid cell for their investigations of the carbides in high speed steel.* It will be demonstrated here that this type of cell is capable of yielding quantitative results in the case of high speed steel, and actually has certain advantages over the more complicated double cell. However, in order to provide a rigorous test of the quanti-tativeness of electrolytic procedures for the problem at hand, both methods were studied in considerable detail.

Jan 1, 1950

By G. R. Speich, L. Zwell, H. A. Wriedt

HORNBOGEN1 has recently shown that it is possible to measure the degree of segregation accompanying cellular precipitation in ferritic Fe-Zn alloys by measuring the lattice parameter of the ferrite phase within the cell. In extending this work to study a wider range of composition and to evaluate the free-energy change accompanying the growth of the cells, the lattice parameter and the boundary of the a! phase in Fe-Zn alloys were redetermined to check the earlier work of Schramm.2 This appeared to be necessary since the Fe-Zn diagram has been drastically revised since the work of Schramm. Stadelmaier and Bridgers3 have recently shown that, contrary to prior belief: the y iron field is closed and the a phase boundary extends to an a + T + L peritectic at 782°C where peritectic a contains 42 at, pet Zn. The phase T in equilibrium with the a solid solution has a composition near Fe3Zn10 and a cubic 081 type structure.&apos; The alloys were prepared by two different methods. In the first method carbonyl iron powder (400 mesh, 99.8 pet pure) and high-purity zinc powder (200 mesh, 99.99 pet pure) were mixed in a ball mill and then pressed in a die at 40,000 psi pressure to make compacts with a diameter of 5/8 in. and a thickness of l/4 in. These were sealed in evacuated quartz capsules, gradually heated to 1100°C over a period of 1 week (3 days at 600°C) 3 days at 800°C, 1 day at (1100°C), and then quenched in iced brine. For the alloys containing 23.4 and 30.1 at. pet Zn, the final homogenization anneals were performed at 1000" and 850°C) respectively, to prevent melting. In the second method, alloys were prepared by saturating high-purity iron millings (0.001 in. thick, 99.9 pet pure) in zinc vapor. For each alloy the impregnation was conducted at a fixed vapor pressure of zinc and a fixed temperature between 750&apos; and 800°C. When saturated, the millings were quenched in water. The compositions of the alloys prepared by both methods are shown in Table I. The lattice parameters of the ferritic solid solutions were determined by comparing the 26 values of their 310, peaks (using Co Ka) or of their 211 , peaks (using Cr Ka) with those of corresponding peaks for high-purity a iron. The 20 values were measured at room temperature with an X-ray dif-fractometer (G.E.-XRD5). By using a fiducial value of 2.8664Å for the lattice parameter of pure a iron at 25oC,5 the lattice parameters of the zinc-bearing

Jan 1, 1964

By C. M. Wayman, J. F. Breedis

The crystallography of the martensitic transformation in the Fe-30 Ni alloy was reinvestigated. The scatter in the habit Plane as determined from measurements on the mid-rib plane was smaller than reported previously, and the orientation relationship was determined from a martensite plate having known direction cosines. From agreement with crystallographic theory and from observations of the morphnlogy of the martensite plates, it is suggested that the mid-rib plane represents the starting region of the transformation. THE crystallography of the martensitic transformation in the iron-nickel system has been the subject of many investigations.&apos;-7 However, for iron alloys containing approximately 30 wt pct Ni, a wide scatter in the reported habit planes exists. In only one instance has a Laue determination of the orientation relationship been made, but the habit plane of the martensite plate studied was not determined experimentally. Because the most successful thermodynamic and kinetic analyses8 of the martensite transformation have been based on Fe-30 Ni alloys, it was considered desirable to reinvestigate the crystallographic features of the transformation in this alloy. Lieberman9 suggested that the most significant information for use in a theoretical treatment involves the determination of all the crystallographic observables from a single plate of the product phase. This was first done in essence by Greninger and Troiano10 for Fe-22 wt pct Ni-0.8 wt pct C, and is the method followed in this investigation. Some theoretical approaches11-13 in describing the martensitic transformation consider the overall transformation distortion to be comprised of a Bain distortion, or lattice deformation (PI, which produces the structure change, and a lattice invariant deformation (G), such as twinning, which together leave the interface or habit plane un-distorted. The incorporation of a rigid body rotation (R) results in a transformation distortion (E) such that the interface plane is left both undistorted and unrotated. In matrix notation, E = RPG where the lattice invariant deformation has "taken place" in the austenite. Bowles and Mackenzie14-16 in formulating a theoretical approach proposed an adjustable scaler quantity, denoted as 6, which represents a uniform dilation in the interface plane. This dilation acts to adjust the lattice spacings of the parent and product structures at the plane of contact. Using the dilation parameter as a variable, these authors were able to account for a continuous variation of habit planes in steels along a curve in the stereogram between {225}A and {259}A. she invariant line strain14 of the transformation is 6 RP, and the corresponding transformation distortion is E/6.) With the dilation parameter known, the invariant line is computed as the triple coincidence of the habit plane, the shear plane of the lattice invariant deformation, and the initial Bain cone.14 The contraction axis for the Bain distortion can be taken9&apos;17 as [010]A, and the correct permutation of the habit plane indices used. Kelly and Nutting 18 have established the shear plane (of twinning) in the tetragonal martensite of Fe-22 Ni-0.8C to be {112)M by means of transmission electron microscopy. The reasonable shear system is then {112}M which is equivalent to {011}A <01l>A. The as-

Jan 1, 1962

By Larry Kaufman, Morris Cohen

THE solid phase equilibria&apos; and the martensitic transformation in the iron-nickel system have been the subject of considerable study. In addition, there have been numerous investigations on the calorimetric and thermodynamic properties of iron-nickel alloys. The purpose of the present work is to extend the existing information concerning the martensitic reaction in the iron-nickel system, and to develop a general thermodynamic treatment which will encompass the equilibrium and non-equilibrium phase

Jan 1, 1957