Search Documents

By B. P. von der Heyden, P. Neethling, M. Tadieb, L. Babedi

The effects of trace element substitutions in sphalerite mineral structure on optimised floatation response have, as yet, not been fully constrained or fully understood. To further this important field of study, this contribution focusses specifically on mineral and surface chemistry, and electro-chemistry of Cd- and Co- substituted synthetic sphalerites using Raman spectroscopy and Zeta potential experimentation. Raman spectroscopy illustrates that the presence of these impurities results in the introduction of a new mode, the relative intensity of which can be correlated (Cd r2=0.95 and Co r2= 0.99) to the dopant concentration. Comparison to X-ray Diffraction results measuring the unit cell parameter further shows that this relative intensity (Cd r2=0.81 and Co r2= 0.99) may provide insights into the degree of lattice strain within the mineral structure. The zeta potential distribution of an un-activated Cd-sphalerite show no detrimental effect as function of Cd content. Although the iso-electric point shifted from 2.45 at 1 wt.% Cd to 2.69 at 3.68 wt.% Cd, the zeta potential remained negative at alkaline media. Conversely, cobalt at low concentration of 0.36 wt.% had a detrimental effect on the surface charge, resulting to a close to neutral zeta potential at different pH. The adsorption of Cu ions on the surface of Co-bearing sphalerite conditioned in an alkaline media slightly increases the zeta potential of Co-sphalerite. While the Cd-bearing sphalerite decrease in negative zeta potential at >1 wt.% Cd indicating a complete exchange between Cu and Zn. The results presented herein illustrate that, based on the chemical nature of the substituting metal; sphalerite will exhibit multiple response to flotation reagents. Maximum recovery of zinc can thus only be achieved through multidisciplinary study and fundamental understanding of the effects of cation substitution on mineral structure and surface chemistry, the latter necessarily affecting the floatation response.

Jan 1, 2018

By W. J. Miles

At the beginning of the 20th century, barite was a mineral of minor importance in the United States. Its primary use was to extend lead oxide in white paint. Barite also added the special qualities of hiding power and flatness to paint. Because white lead sometimes turns black or yellow and barite does not, ground barite became a pigment on its own merit. Barium chloride was added to bricks before fi ring to stop efflorescence when exposed to weather. Barium carbonate or nitrate added luster and brilliance to glass. Barium chemicals were added to refining sugar, enameling iron, making oilcloths and paper collars, and in the manufacture of paper, artificial ivory, rubber and lithopone. Lithopone became a major paint ingredient in the 1920s; its use lasted until the 1950s, peaking at 150 kt (165,000 st) of barite in 1937 and 1947 for the manufacture of lithopone. Later in the 20th century, titanium dioxide replaced lead oxide, barite and zinc oxide in the coatings industry. In the 21st century, barite is used as a filler, extender or weighting agent in products such as paints, plastics and rubber. Some specific uses include its use in brake and clutch pads for automobiles, automobile paint primer for metal protection and gloss, to add weight to rubber mud flaps on trucks and to add weight to the cement jacket around petroleum pipelines under water. In the metals casting industry, barite is part of mold release compounds. Because barite significantly blocks X-ray and gamma ray emissions, it is used as aggregate in high density concrete for radiation shielding around X-ray units in hospitals, nuclear power plants and university nuclear research facilities. Ultra-pure barite consumed as liquid is used as a contrast medium in medical X-ray examinations. Barite is the raw material for barium chemicals, such as barium carbonate, which is an ingredient in faceplate glass in the cathode-ray tubes of televisions and computer monitors. In the 21st century, barite industrial uses accounts for an estimated 78 kt/a (86,000 stpy) in the United States.

Jan 1, 2009

By W. J. Miles

At the beginning of the 20th century, barite was a mineral of minor importance in the USA. Its primary use was to extend lead oxide in white paint. Barite also added the special qualities of hiding power and flatness to paint. Because white lead sometimes turns black or yellow and barite does not, ground barite became a pigment on its own merit. Barium chloride was added to bricks before firing to stop efflorescence when exposed to weather. Barium carbonate or nitrate added luster and brilliance to glass. Barium chemicals were added to refining sugar, enameling iron, making oilcloths and paper collars, and in the manufacture of paper, artificial ivory, rubber and lithopone. Lithopone became a major paint ingredient in the 1920s; its use lasted until the 1950s, peaking at 150,000 metric tons of barite in both 1937 and 1947 for the manufacture of lithopone. Later in the 20th century, titanium dioxide replaced lead oxide, barite and zinc oxide in the coatings industry. In the 21st century, barite is used as a filler, extender, or weighting agent in products such as paints, plastics, and rubber. Some specific uses include its use in brake and clutch pads for automobiles, automobile paint primer for metal protection and gloss, add weight to rubber mud flaps on trucks, and add weight to the cement jacket around petroleum pipelines under water. In the metals casting industry, barite is part of mold release compounds. Because barite significantly blocks X-ray and gamma ray emissions, it is used as aggregate in high density concrete for radiation shielding around x-ray units in hospitals, nuclear power plants, and university nuclear research facilities. Ultra-pure barite consumed as liquid is used as a contrast medium in medical X-ray examinations. Barite is the raw material for barium chemicals, such as barium carbonate, which is an ingredient in faceplate glass in the cathode-ray tubes of televisions and computer monitors. In the 21st century, barite industrial uses account for an estimated 78,000 tons per year in the United States. Another barite use was patented in 1926 by the oil industry. In this patent, barite is primarily used as a non-abrasive weighting agent for drilling for oil and gas exploration and production. As a weighting agent, it provides the downward force in a water based or oil based drilling fluid for cutting through rock with a tri-cone diamond drill bit. In order to minimize the wear on the drill bit and drill stem, minimum abrasion of the weighting agent is preferred. In recent years in the USA, 95% of the barite produced and about 80% on a world basis are used as a fluid weighting material during the search for oil and gas. During the latter part of the 20th century, barite was used in the drilling mud of oil and gas wells, particularly for wells deeper than 2000 meters, and petroleum well drilling demand for barite became the mineral?s major end use during economic expansions after World War II and subsequent increased use of oil and gas in the USA. The profitability of oil and gas production had a strong effect on the number of drill rigs and consumption of barite. The United States was the leading petroleum well drilling country starting in 1970, reaching 4,530 drill rigs in December 1981, and was the largest consumer of barite. In the USA, record highs of about 2.6 million tons of barite produced and 4.3 million tons consumed were reported in 1981. From 1997 to 2006, barite production declined from 662,000 to 589,000 metric tons. However, USA imports increased from 1,470,000 to 2,530,000 metric tons for lump barite. World production of barite increased from 6,780,000 to 7,960,000 metric tons during the same period. Table 1 (see Appendix) lists USA production, imports and exports and world production from 1997 to 2006. Major sources of imported barite include China, India and Morocco. Table 2 (see Appendix) lists the USA imports and price of barite by country. China, India and Morocco are the three largest exporters of barite to the USA and the world. Vietnam is a new producer, beginning in 2006. IMPACT OF CHINA ON DRILLING GRADE BARITE In the 1970s or before, China began supplying barite to the world drilling market in order to help develop their economy. When China first entered the barite export market, their high production volume, low pricing and low ocean transport expenses to the Gulf Coast forced barite producers in the USA to supply only regional markets, such as Battle Mountain Nevada barite for the western and Rocky Mountain states and Canada. Until recently, it was China?s government policy for domestic consumers to use barite below the API 4.20 specific gravity specification, leaving higher grades for export, but this is no longer the case. In recent years the internal demand for barite in China increased tremendously as their economy rapidly developed. China reduced their former 15% VAT tax rebates to 5% for Chinese barite producers, and then eliminated all VAT tax rebates on December 15, 2006. On the supply side, some high-grade barite deposits in China have been depleted. In particular, the low heavy metals sources are less plentiful. Additional mine capacity is being developed, but the new mines are underground and therefore costs will be higher. China?s appetite for other raw materials has tied up a large portion of the world?s bulk vessel fleet, including Panamax vessels (preferred for barite ore transport). Ocean transport freight rates have increased in recent years, and receiving ports in the USA are congested with imports of higher-added-value products. The Panamax Index, which tracks maritime shipping rates, more than doubled in 2006. China has also devalued its currency from RMB8.30 to RMB7.80 per dollar. These factors are driving up the import price of crude and ground barite for drilling. In addition, in the USA, rail congestion and high fuel prices led to higher trucking rates, increasing the delivered cost of ground barite to oil customers. India is the second largest supplier of crude barite to the USA and world drilling market. It produces all of its barite from a single deposit in the Cuddapah region of Andhra Pradesh State. More than 90% of production comes from the State-owned Andhra Pradesh Mineral Development Corp., and the government continues to closely control production, export volumes, and prices. India saw a dramatic increase in barite prices as a result of its last 3-year tender in 2004. However, in 2004 and 2005 their shipments of crude barite to the USA were not significant. In 2005, India began supplying barite pulverized to meet API specifications to the Gulf Coast. In 2006, Indian production was reduced owing to severe flooding in November 2005 that curtailed mining until mid-April 2006. Morocco has been the third largest supplier of crude barite to the USA and world drilling market. In 2003 and 2004 their shipments of crude barite to the USA were not significant. In 2005, Morocco resumed shipment of crude barite to the Gulf Coast and began supplying barite ground to meet API specifications to the Gulf Coast.

Jan 1, 2009

By D J. Williams, A K. Kho, A Shokouhi, N Tucker

The disposal of dewatered coalmine tailings and coarse reject within spoil piles is gaining popularity as a means of eliminating separate surface tailings storage facilities or dams. The contrasting characteristics of coalmine spoil, coarse reject and tailings are somewhat complimentary, making the co-disposal of dewatered tailings within spoil piles geotechnically feasible and environmentally attractive. However, the impacts of mixing plant rejects within spoil piles are not well understood; in particular, the effects of water draining from the mixed plant rejects on the moisture content of the surrounding spoil. Changes in moisture content can cause additional collapse and degradation settlements of the spoil pile. A series of laboratory tests has been undertaken on mixtures of dewatered coalmine tailings, coarse reject and spoil. The results of these tests have been incorporated into a spreadsheet-based settlement prediction tool to investigate the effects of incorporating mixed plant rejects on total spoil pile settlements. This paper presents the laboratory tests undertaken, the incorporation of the test data into the settlement prediction tool, and settlement estimates for the various mixtures at different stages of construction.CITATION:Kho, A K, Tucker, N, Williams, D J and Shokouhi, A, 2015. Impact of co-disposing mixed plant rejects on spoil pile settlements, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By K. Dagdelen , S. K. A. Owusu

Uncertainty with regard to estimated grades and tonnages of a mineral deposit demands risk assessment in order to build investor confidence and attract the interest of other stakeholders in the success of a project. Uncertainties associated with Mineral Resource estimates can lead to unreliable production schedules and unpredictable cash flows. However, the techniques used in the mining industry to determine these uncertainties are inconsistent, because the important decisions taken in the process are solely dependent on the responsible Competent Person (CP), without limitations. This leads to disparities between different CPs’ results, using data-sets from the same drill-holes. The various standard codes for public disclosure provide guidelines and recommendations for the classification of Mineral Resources and Reserves but do not provide details on, for example, the amount of geological and geostatistical information needed to qualify for each category of Resources and Reserves. The parameters used to generate the classification categories are subjectively assumed by the responsible CP. In this paper we investigate the impacts of different CPs’ judgements on resource classification, using the same data-sets. The results underpin the need for the mining industry to develop a uniform Mineral Resources and Reserves classification framework that can minimize or avoid significant discrepancies that lead to potential misleading public disclosures.

Aug 8, 2024

By R. J. Sweigard, C. T. Justice, T. Beckham, E. D. Thompson, T. C. Hopkins

Fine coal refuse is often pumped, as slurry, into surface impoundments as a means of permanent disposal. As the available volume is filled, the height of the embankments are frequently increased. Many times the additional embankment material is placed upon consolidated fine coal refuse. There has been some concern about the long-term effect of consolidation of this material at or above the liquid limit upon its shear strength. A laboratory investigation was performed using three different types of fine coal sluny taken from Central Appalachian coal preparation plants. The refuse was consolidated in 10-foot plexiglass columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart and triaxial tests were performed on both the consolidated material and unconsolidated material for comparison of their shear strength parameters.

Feb 24, 1997

By C. Sawmliana

Deep-hole blasting operations in opencast mines are always associated with some annoyance to the surrounding areas in terms of ground vibration, noise, flyrock, etc. These become more severe when underground mines run parallel to them. Blasting in opencast mines may pose danger to the underground mines in terms of roof/side failures, damage of water dams, isolation/ventilation stoppings and other underground installations. The paper discusses a case study in India on the impact of deep-hole blasting in Ramagundam Opencast Project ? III on the stability of various water dams of GDK-6B Incline coal mine operating in close proximity. The stability of underground water dams of GDK-6B Incline mine was endangered due to deep-hole blasting at OCP-III. There were 15 water dams in seam 3 and 16 dams in seam 4 of the underground mine. The physical strength tests using a Schmidt Hammer instrument were carried out in all the 15 water dams of No. 3 seam and 16 water dams of No. 4 seam. The test revealed that there is a decrease in compressive strength values of three dams of seam 3, namely 6A, 6B and 7. Theose three dams were also directly connected to the water source. Water seepage was also observed from the surfaces of the three dams. However, they were found to be stable in accordance with their design parameters and damage point of view while considering a threshold value of ground vibration as 25 mm/s. It was found that the value of tensile stress generated by a vibration of 25 mm/s was much lower (i.e. 0.171N/mm2) than the tensile strength of the two weakest concrete dams (1.85 N/mm2). Ten experimental blasts were conducted at different working benches of the opencast mine and the ground vibration data were recorded in roof and pillars near various underground water dams. The maximum value of vibration data recorded was 5.9 mm/s in roof near dam no. 1 in seam 3 with the dominant peak frequency of 22 Hz. No adverse effect on either of the dams was observed after that blast. During the period of study, no deterioration/adverse impact was found in any dam of the mine. Based on the results of the study and the analyses of the data, optimized blast design parameters and explosives weight per delay were suggested for the opencast mine to maintain the safety of the underground water dams. Keywords: Opencast blasting, damage, water dams, underground mine, ground vibration

Jan 1, 2009

By T. J. Batchler

Deformable materials are sometimes added to ventilation stopping constructions to prevent damage caused by convergence in coal mines. However, adding deformable materials can significantly reduce the capacity of a stopping to resist transverse loading. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) has conducted research on the effect of various materials with different deformation properties on the transverse loading capability of a stopping wall. Based on a three-point hinge method of failure, a half-wall method of testing in the NIOSH Mine Roof Simulator was used to simulate full-scale wall behavior. This simulated the fracture initiation and eventual failure of the stoppings from transverse loading. The impact of the modulus of elasticity of various deformable materials was examined in this study. A polystyrene foam block with a low modulus of elasticity, which is commonly used as a deformable material, was shown to degrade the transverse load capacity of the stopping by as much 95%. Other materials with higher modulus of elasticity preserved more of the transverse load capacity of the stopping, but were not able to absorb as much convergence. This paper presents the results of a parametric study that quantifies the impact of various deformable materials in block stopping construction under transverse load conditions. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By C. Birch

"The purpose of this study was to establish the impact of discount rates on cut-off grades for narrow tabular gold deposits as characterized by the goldfields of the Witwatersrand Basin in South Africa. There are various methods available for determining the cut-off grade, from simple breakeven calculations to sophisticated software packages that consider a variety of inputs to optimize the cut-off grade. For this study a simple financial model was created in Microsoft Excel® that links the ore flow, block listing, and the cash flow. This allows the cut-off grade to be optimized considering how the cost of capital and chosen discount rate affect the cash flow.The discounted cash flow (DCF) and resultant net present value (NPV) are a widely used valuation method for production properties according to the South African Code for the Reporting of Mineral Asset Valuation (SAMVAL Code). The financial model in this study utilizes the Solver function, as well as simple Microsoft Excel spreadsheet formulae to optimize the NPV. Solver was chosen as it is a standard feature in Excel and thus no additional software costs are incurred beyond the basic Microsoft Office suite. For the purpose of this study, just narrow tabular gold deposits of the Witwatersrand Basin were considered. An example of a typical ore block listing, as well as the costing figures, was obtained from an operating gold mine. The results obtained from the study financial model were compared to the current cut-off grades obtained from the mine using their proprietary optimizer program, and were found to be comparable. The methodology utilized for this study thus appears valid.The cut-off grade was optimized considering the cash flow, which includes the variable mineral resource royalty tax, the variable gold income tax, as well as the discount rate. By comparing the resultant NPVs using discount rates of zero, 9%, and 12%, the impact of the discount rate on cut-off grades, resultant life of mine, and average mining grades (AMG) could be compared for the example ore block listing. The South African Code for Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code) does not require operations to state if a discount rate was considered in determining mineable reserves. Mining companies approach the question of applying discount rates in determining their cut-off grades, and thus mine planning strategy, in different ways. Due to the negative impact that optimizing purely on NPV has on the life of mine, some choose to optimize only on profit. Other companies have reverted to utilizing pay limits as their primary grade planning strategy. The calculated cut-off grade is then considered to be another planning indicator rather than a hard determination of mineable reserves."

Jan 1, 2016

By Thomas J. Keefe, O&apos

Results of metal electrodeposition experiments conducted at the University of Brussels and University of Missouri-Rolla over the past few years are reviewed in terms of the relationship and impact on industrial processes. Examples are cited from common electrowinning, electrorefining, or electroplating operations for copper, zinc, nickel, cobalt and silver. The following topics are considered : metallographic structure, crystallographic texture, surface morphology, nucleation and growth, additive monitoring and effects, high current density, substrate related properties including adhesion. The studies were conducted on a variety of scales from laboratory beaker tests to full sized pilot and industrial operating plants.

Jan 1, 1993

By G. Caron, M. Boisclair

In 2005, CANMET-MMSL used its pool of expertise in ground control, open pit and underground mine engineering, mineral processing, information technology and applied mineralogy to launch a mine-to-mill research project. The objective of the project was to optimize the distribution of rock breakage energy among blasting, crushing and grinding activities, thereby maximizing the efficiency of energy utilization within comminution processes. Tests were designed to demonstrate that this approach could reduce the energy consumption, thus contributing to the reduction of Green House Gas (GHG) production in the Canadian mining industry. The project was accomplished in collaboration with DynoConsult and Dyno Nobel Canada Inc., a world leader in commercial explosives. Data analysis from 12 blasts (six with electronic and six with pyrotechnic detonators) in three different geological formations of a quarry (soft, medium and hard rock) shows that electronic blasting technology increases rock fragmentation by 15% (in hard rock) to 20% (in soft rock). A more uniform rock fragment size distribution is also obtained. The impact of the improved quality blast product on downstream processes of the quarry is a productivity increase of 5% in rock excavation and transportation, an energy reduction of 10% at the primary crusher and an increase of 15% of the primary crusher throughput. A soft-sensor prototype, based on primary crusher data (i.e. energy consumption, throughput, feed and product size distribution) and a simplified computerized process model, was developed for on-line measurement of the rock operating work index. Additionally, 385 rock samples and specimens were collected and prepared to determine the tensile and compressive strength of the rock material, to evaluate the aggregate crushing work index, and to examine the development of micro- and macro-fractures by means of binocular and SEM microscopy. Blast-induced rock damage was evaluated at the end of the laboratory testing program. Even though a reduction of rock hardness of around 30% was observed after blasting, the impact of the blasting method (i.e. use of electronic or pyrotechnic detonators) on the induced rock damage could not be observed. It is either absent or not perceptible with the accuracy of the measuring techniques and the number of samples analyzed.

Jan 1, 2007

In 2005, CANMET-MMSL used its pool of expertise in ground control, open pit and underground mine engineering, mineral processing, information technology and applied mineralogy to launch a mine-to-mill research project. The objective of the project was to optimize the distribution of rock breakage energy among blasting, crushing and grinding activities, thereby maximizing the efficiency of energy utilization within comminution processes. Tests were designed to demonstrate that this approach could reduce energy consumption, thus contributing to the reduction of green house gas (GHG) production in the Canadian mining industry. The project was accomplished in collaboration with DynoConsult and Dyno Nobel Canada Inc., a world leader in commercial explosives. Data analysis from 12 blasts (six with electronic and six with pyrotechnic detonators) in three different geological formations of a quarry (soft, medium and hard rock) shows that electronic blasting technology increases rock fragmentation by 15% (in hard rock) to 20% (in soft rock). A more uniform rock fragment size distribution is also obtained. The impact of the improved quality blast product on downstream processes of the quarry is a productivity increase of 5% in rock excavation and transportation, an energy reduction of 10% at the primary crusher and an increase of 15% of the primary crusher throughput. Extended to the Canadian mining industry, such results would represent a GHG emission reduction of about 0.05 Mt/y. A soft-sensor prototype, based on primary crusher data (i.e., energy consumption, throughput, feed and product size distribution) and a simplified computerized process model, was developed for on-line measurement of the rock operating work index. Additionally, 385 rock samples and specimens were collected and prepared to determine the tensile and compressive strength of the rock material, to evaluate the aggregate crushing work index and to examine the development of micro- and macro-fractures by means of binocular and SEM microscopy. Blast-induced rock damage was evaluated at the end of the laboratory-testing program. Even though a reduction of rock hardness of around 30% was observed after blasting, the impact of the blasting method (i.e., use of electronic or pyrotechnic detonators) on the induced rock damage could not be observed. It is either absent or not perceptible with the accuracy of the measuring techniques and the number of samples analyzed.

Jan 1, 2008

By M Bilodeau, G Caro, R Beaudoin, D Labrie

In 2005, Dyno Nobel Canada Inc, DynoConsult and CANMET-MMSL used their pool of expertise in blasting, ground control, open pit and underground mining, mineral processing, information technology and applied mineralogy to launch a research project aimed at evaluating the role of electronic detonators in the development of a sustainable energy-efficient rock reduction process. The overall objectives were to improve health and safety in a mining environment and reduce energy consumption and greenhouse gas (GHG) production in the Canadian mining industry. The study was conducted in a quarry located in Nova Scotia, Canada, with the objective of taking advantage of the higher accuracy and flexibility of electronic detonators towards improving blast efficiency and measuring its impact on productivity in a quarry environment and energy savings. Optimising the blast sequence was the first aspect to be considered before starting to look at designing bigger blasts and achieving productivity improvements, without creating additional environmental concerns, as the quarryÆs location was representing a challenge in itself in the surrounding community. The use of high-speed cameras (500 fps) was an improved means of analysing blast dynamics during the firing sequence. Seismic monitoring and linear superposition techniques were also applied to validate the sequences to be tested in all three specific geological areas. The combination of field measurements allowed to identify the optimal blasting sequences that would then be delivered accurately with the electronic initiation systems. The data from 12 blasts (six with electronic detonators and six with pyrotechnic detonators) carried out in three different geological formations (soft, medium and hard rock) showed that the electronic blasting technology could increase rock fragmentation by 15 to 20 per cent. A more uniform distribution of rock fragment size was also obtained. Blast improvements on downstream processes resulted in a five per cent productivity increase in rock excavation and transportation, a ten per cent energy reduction in primary crushing and a 15 per cent increase in the primary crusher throughput. A prototype soft-sensor based on primary crusher data (eg energy consumption, throughput, feed and product size distribution) and a simplified computer process model were developed for online measurement of a rock operating work index. Furthermore, rock samples were collected and specimens were prepared in order to determine the tensile and compressive strength of the rock materials, evaluate the aggregate crushing work index and examine the development of micro and macro-fractures under binocular and scanning electron microscopy (SEM). Blast-induced rock damage was evaluated at the end of the laboratory testing program. A reduction in rock hardness by about 30 per cent was observed after blasting. However, the impact of the blasting method (eg using electronic versus pyrotechnic detonators) on the induced rock damage was either absent or not perceptible within the measurement technique accuracy and the number of samples analysed.

Jan 1, 2007

By R. D. Short

Environmental regulations for noise and air pollution are directly affecting the type of equipment and construction techniques being utilized for pile driving construction using diesel hammers in California and elsewhere. Consequently, the cost of construction is increasing and in some cases, the use of diesel pile hammers has been prohibited. Based on the trend in California and elsewhere in the world, environmental constraints are spreading and becoming more restrictive. The City of Tokyo, Japan, for example has banned the use of diesel hammers. Environmental restrictions on diesel hammers can be satisfied by using modern hammers, clean burning fuels, synthetic lubricants and pre-excavation techniques.

Jan 1, 1989

By W. F. Riggs

INTRODUCTION Flotation equipment is becoming more definitive in design as well as greater in dimension. The last ten years have witnessed the implementation of large flotation cells ranging in size from 28 to 85 cubic meters. However, small plants still operate with cells as small as 3 cubic meters. These changes have increased the operational sensitivity of the flotation system to the chemical reagents used. No scientific study has been undertaken to develop the relationship between the size of equipment and the response of reagents in the flotation system. Hence, this article is an attempt to present several observations from past experience for the purpose of stimulating future research in an area previously ignored and perhaps subsequently not used to advantage. CONVENTIONAL FLOTATION Recent advances in conventional flotation cell design have been made in two areas: a. Flotation cells are becoming larger, and b. Basic design of flotation cells has changed. They can be classified into two types: deep cell and shallow draft cell. Size and design changes of flotation cells have a greater effect on frother performance than on the performance of other chemical reagents. Hence, the discussion in the following sections is restricted to the impact of frothers in the flotation system. Flotation Cell Size The advent of increasing flotation cell size has resulted in the increase of frother consumption. There appears to be a correlation between reduced horsepower (kilowatt) consumption and increased frother consumption per ton of ore processed in the circuit. This is more prevalent when the frother chemistry remains unchanged. Another reason for increased frother consumption is the increased distance between the rotating central shaft and the lip of the cell for larger flotation machines. Increasing this distance results in increased surface area corresponding to the larger cell size. Reduced power input per ton combined with the need for longer, stronger load support of the froth bubble as a result of increasing cell size has resulted in the development of a new series of stronger and more persistent frothers. By the same token, these newer, stronger frothers are difficult to control when applied to the smaller cells. This is true even at lower dosages because the break point between too much frother and not enough frother for optimum metallurgy is normally very narrow. This problem is often exaggerated when operators have established an optimum setting for pulp level and air for the particular frother in use. Generally, the tendency is to operate the flotation cells simply by adjusting frother dosage. The increase in frother strength to accommodate the large cells often results in the realization, after a retrofit, that the existing pump box or sump which is still handling the same volume of concentrate is no longer adequate in size. Flotation Cell Design The two most common flotation cell designs installed during the past ten years are the deep cell and the shallow draft cell. The deep cell provides for complete mixing of air and pulp at the bottom of the cell. The shallow draft cell does all the mixing/pumping in the bottom haft of the cell whereas the mixing of the air is performed further up the shaft and is brought into contact with the pulp midway up the vortex. There are many preferences for one or the other. It is the author's contention that both designs have very valid concepts and must simply be suited to the particular situation as required by the operator. The following comments are subjective observations which should be explored in greater detail. The deep cell mixes both air and pulp together at the bottom of the cell requiring a full depth ascending of the homogenized air to the surface to form the froth layer. This design, in combination with charged air, provides for good concentrate grade control under adverse conditions of selectivity, especially when faced with a fine grind and a slime-laden gangue. A selective frother can be applied without a competitive loss in recovery. One of the conditions for good selectivity in this environment is operating at medium pulp solids concentration in the range of twenty-six to thirty-four per cent (26-34%). When a higher solids concentration is used in combination with a coarse grind, it becomes difficult to maintain the same recovery with a selective frother due to higher pulp viscosity. This condition sometimes results in an unacceptable coalescence of the air bubbles as they ascend the full height of the deep cell. The increased pulp viscosity at higher solids concentration can also retard the flotation kinetics. The combination of decreased surface area of dispersed air and slower kinetics can result in reduced recovery causing coarse particles to continue to drop

Jan 1, 1989

By J. F. T. Agapito

The load carrying capacity of oil shale pillars excavated by conventional blasting, presplit blasting, and mechanical mining is evaluated. The study was based on a comparison of in-situ vertical stresses and fractures obtained from overcoring horizontal holes in the Colony Mine, Piceance Creek Basin, Colorado. Results indicate that conventional blasting causes a zone of damage approximately 3 m (10 ft) thick with low stress distributions. Presplit blasting reduces damage significantly, and increases the load carrying capacity in the 3 m (10 ft) thick zone by 5.93 MPa (860 psi). Mechanical mining causes little or no rock damage, and an increase of 9.83 MPa (1425 psi) in strength in the same 3 m (10 ft) thick zone. An example of pillar design is given showing that the use of presplit blasting and mechanical mining techniques can increase the extraction ratio by at least three and five percent, respectively, as compared to conventional blasting. It is speculated that comparable increases in extraction should also occur due to increases in span dimensions.

Jan 1, 1984

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and, thus, deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the gob and to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Sep 1, 2013

By R. H. Grau

Researchers from the National Institute for Occupational Safety and Health have demonstrated that mine-wide ventilation in large-opening stone mines can be improved by using low-pressure, high-volume propeller fans and constructing stoppings in key locations to direct and control airflow. In light of these findings, a comparative study was conducted to determine if a portable diesel-powered propeller fan could per-form more efficiently for dust dilution and transport than an axial vane fan for localized ventilation. The objective of this study is to evaluate both fan types for ventilation efficiency at an underground dump/crusher facility in a limestone mine. Results showed an improvement with the propeller fan to dilute both the respirable dust and the respirable silica dust around the dump/crusher facility. Overall, an average reduction of 20% in respirable dust and silica was observed at the dump/crusher location with the propeller fan.

By O. Rielo, P. Katsabanis

Traditionally fine aluminum is not used in dry commercial explosives due to the hazard associated with aluminum dust explosions during mixing. An industrial process has been developed which enables the safe use of paint grade Aluminum with ANFO. The addition of fine aluminum particles resulted in increased velocity of detonation of ANFO compositions. Velocities of detonation, in 52mm (2 1/16 in.) diameter confined charges were 20% higher than velocities of detonation of straight ANFO. The detonation performance of fine grained ANFO was not benefited by Al at the diameter tested. Furthermore use of larger Al flakes resulted in decreased velocities of detonation. The results are compatible with the experience of Al addition to high explosives. Tests were also conducted using bio-diesel, finding no substantial difference in the performance of AN fuel explosive compositions which used bio-diesel.

Jan 1, 2009

By D. Pawelus, J. Butra, R. Debkowski, M. Szpak

Impact of horizontal stresses on stability of underground workings in mines is a very important issue in underground mining. Identification of the initial state of stress in the rock-mass should be one of the main actions taken into account while designing and carrying out the mining activity in underground mines. The paper presents the tests on three dimensional stress pattern in Polish copper mines, owned by KGHM Polska Miedz S.A. Group, carried out in 2012. The research program covered 7 measuring stands in two mines; their average depth was about 1000 m. The main aim was to identify the values and directions of horizontal stresses in order to optimize the extraction and to improve the safety. The overcoring method with the use of CSIRO HI type probe was applied. The paper also describes the measuring technique which was developed for the purpose of specific mining and geological conditions of KGHM mines, taking into consideration the natural hazards encountered there as well as technical and operational capabilities with regard to drilling equipment. The experience gained during the underground measurements and the issue of making such measurements in underground copper mines in Poland are presented in the paper. The stress patterns obtained during the underground measurements are of application importance for the process of designing the spacing of mine workings and improving their stability and mine support selection.

Jan 1, 2015