Search Documents

By D. Dolinar, T. P. Mucho

Horizontal stresses are caused by global platetectonic forces. During 1995 alone they were largely responsible for the closing of two longwall mines in the United States. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky and Alabama. In each case, a mine encountered roof falls or difficult ground conditions at the headgate caused by horizontal-stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble free. The paper also discusses detailed measurements that were made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal-stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel to the maximum horizontal stress, as previously thought, but rather it is 20o in the stress shadow of the gob. Other stress-control techniques, including artificial support, are briefly discussed

Jan 1, 1999

By Thomas P. Mucho, Dennis Dolinar, Christopher Mark

Horizontal stresses are caused by global plate tectonic forces. During 1995 alone, they were largely responsible for closing two U.S. longwall mines. This paper presents six case histories from Pennsylvania. West Virginia, Kentucky and Alabama. In each case history, a mine encountered roof falls or difficult ground conditions in the headgate, caused by horizontal stress concentrations. The problems are detailed and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble-free. The paper also discusses detailed measurements made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel with the maximum horizontal stress, as previously thought but rather 200 in the stress shadow of the gob. Other stress control techniques, including artificial support, are briefly discussed.

Feb 24, 1997

By J. B. Lizak

This paper is not available for inclusion in the Proceedings at the time of printing, but it will be included as an insert.

Jan 1, 1984

By J. F. T. Agapito, L. J. Gilbride

High horizontal stresses were recognized to impact roof stability more than 60 years ago. Since then, numerous measurements associated high horizontal stresses with difficult ground conditions. This paper presents case histories illustrating the practical usage of roof stress determinations for helping assess stability, not only in the case of high horizontal stresses but also of low stresses. Examples are given of high stresses associated with faults, mine design changes, quantification of stress shadow effect, and anistrophy. The paper concludes with a comparative evaluation on the effect of various stress fields on ground support requirements.

Jan 1, 2002

By A. P. Squelch

The question of what stress condition exists in the hangingwall of tabular stopes remains topical and largely unanswered. Limited field data exist to quantify the situation and provide calibration for investigative computer modelling exercises. Work conducted in1989 and 1990 under a Chamber of Mines Research Organization (now the CSIR: Division of Mining Technology) programme of research into the behaviour and benefits of backfill may assist with this situation. The original work was motivated by the premise that the improved hangingwall stability in backfilled panels (identified by rockfall accident analyses) is due to a change in the hangingwall stress regime. Current, largely theoretical, studies into mechanisms of stope hangingwall behaviour and support interaction could benefit from considering these data. Keywords: Backfill, horizontal stress, stope hangingwall, hangingwall stability, support interaction.

Jan 1, 2002

By Thomas E. Bruner

Today many small diameter tunnels are being constructed in Metropolitan areas and towns as transmission holes for utilities such as water, electricity, natural gas and sewage, to name a few. These tunnels function as utilities beneath the streets, highways, railways, and other structures where open-cut techniques are impractical for any one of a number of reasons. Many such bores range in diameter from 15 to 72 inches and in lengths from 100 to 500 feet. Auger drills with auger type heads have long been used to bore these "road crossings" as they are usually termed; however, many such crossings must be bored in rock with rock-boring heads. Rock with a compressive strength of 15,000 p.s.i. and higher seems to present the greatest challenge for the contractor. These rocks include most igneous and metamorphic rocks and some sedimentary rocks. In general, this grasps most granites, basalts, gneisses, slates, schists, quartzites, limestones, and cherts. In the past ten years boring machines have been developed and used to excavate road crossings through hard rock. Many crossings have been successfully excavated using these machines, and the degree of success has increased substantially in the last few years. A variety of machines have been built and manufactured to bore most rock in a range of diameters up to 72 inches. The machines vary in capabilities, size ranges, and designs but all perform the same basic task and function of boring horizontally. Incidently, here the term horizontal implies horizontal or within five degrees of horizontal. In addition, there is a wide variety of designs, sizes, and types of drill stems, joints, and pipe to meet the various conditions and

Jan 1, 1974

By A. Noble

Linear circuit analysis (LCA) is a fundamental tool which has been used to evaluate mineral separation circuits during the preliminary design phase. Traditionally, the LCA methodology uses the analytic circuit solution to determine the relative slope of the circuit?s partition curve. This value is then used as an indicative performance measure suitable for the comparison and ranking of alternative circuit configurations. Unfortunately, the partition curve slope only reflects the separation potential of middling material. In most mineral systems, this material represents a small portion of the initial feed (due to liberation) as well as a small portion of the revenue potential (due to the incremental value). Respecting these limitations, the authors have developed new separation performance indicators which may be derived from the analytical circuit solution and used in LCA problems. These indicators inherently reflect the separation potential of pure material, providing a better indication of lost revenue due to misplaced material. The complete methodology has been integrated with prior software to produce the Heuristic Optimizer for Resource Separation Economics (HORSE).

Feb 23, 2014

By Paul Staples, Paul Messenger, Greg Lane

"Every project is different. While “conventional” SAG and ball mill circuits will suit many projects, for others there are alternatives, which may produce improved outcomes. This paper examines particular examples of recent front end designs which either went against conventional thinking or which employed “out of the box” thinking to realize the desired results.One such example is the design strategy employed for a small capacity gold plant in Victoria, Australia. The selection of HPGR technology for small capacity projects is not generally favoured, given the relatively high cost of small HPGR machines. However, the unusual size distribution of the gold and its liberation characteristics were expected to lead to improved gold recovery offsetting the higher capital cost.Another example is the first large scale application of milling in acid for copper recovery, at a project in south east Asia. The stainless steel, single stage SAG mill using ceramic grinding media was more expensive than a mill constructed of conventional materials. However, the steps of scrubbing, slurrying, grinding and leaching could all be achieved in a single unit operation and the need for thickening and repulping with acid after milling was eliminated.Rod mills were selected for both primary and secondary milling duties for another south east Asian project despite their somewhat outdated reputation. A review of previous industry experience confirmed that rod mills could outperform conventional rod/ball or SAG/ball circuits in cases where the size distribution of the ground product is critical to downstream recovery.These examples are discussed with particular focus on the key drivers in each case."

Jan 1, 2008

By Hoeve. J.

"In the unconformity-type uranium deposit at Midwest Lake, mineralization is associated with extensive host rock alteration, which affects the metamorphic basement as well as the overlying Athabasca Group sandstones. Host rock alteration is manifested by (I) transformation of clay minerals [kaolinite into illite and chlorite (sudoile)]; (2) bleaching due to removal of hematite from the lateritic paleoweathering profile and the overlying red bed, Athabasca Group sandstones; (3) loss of coherence of the sandstone resulting from corrosion of quartz cement; and (4) in the immediate vicinity of high-grade ore, development of a clay envelope due to residual enrichment of clay minerals caused by massive dissolution of quartz. Clay mineral transformation and bleaching are the most prominent and the most widespread alteration effects, forming haloes that extend for several kilometres along the strike of the mineralized structure and also constitute distinct alteration pipes that rise f or several hundred metres above the unconformity to be truncated at the present top of the bedrock.Although the two haloes are largely congruent features, cross-culling relationship s indicate that clay mineral alteration represents an earlier phase in the history of the deposit than the large-scale bleaching that gave rise to the superimposed bleaching halo.Because clay mineral alteration and bleaching are intimately tied to the mineralization and extend well beyond the limits of the actual orebodies, host rock alteration may be used as an ore guide in exploration and drill-hole evaluation. In this application a third hydrothermal discharge centre was identified, as yet untested for are, which is located between the hydrothermal centres associated with the two known orebodies of the deposit.It is estimated that host rock alteration may enlarge a potential drill-target by a factor 10 - 20X. Information on the configuration of bleaching haloes can be obtained from systematic core logging, whereas diagnostic clay mineral alteration is readily identified by means of automated, quantitative XRD techniques."

Jan 1, 1984

By J. S. Fox

Major-element data for unaltered, unmineralized felsic host rocks from a number of stratigraphically simple, massive volcanogenic Zn-Cu(-Pb) sulphide deposits of low metamorphic grade have been compiled. The petrochemical affinities of these host rocks have been determined (by standard means and by discriminant analysis) and compared. This comparison indicates that volcanogenic deposits in felsic terrains are not restricted to the classical calc-alkaline rock association as previously thought, but can actually be hosted by rocks showing a range of iron content. There is a positive correlation between differentiation trend and are tenor. Zn-Cu ores usually have iron-rich felsic hosts (most Canadian Shield deposits); Pb-Zn -Cu ores have iron-poor felsic hosts (Japanese, Iberian and Tasmanian deposits). This parallels the antipathetic relationship between iron content and background lead levels evident in young, unmineralized, island arcs as well as in many older belts. Correlations between differentiation trend on one hand and massive ore mineralogy and the relative proportions of various rock type (including rhyolite, quartz-porphyry and coarse pyroclastic rocks) on the other are also evident. It is concluded that the recognition of a calc-alkaline differentiation trend cannot be used as a prospecting guide, as has previously been proposed. However, in view of the above correlations, the recognition of a given trend may aid in the formulation of an effective exploration philosophy.

Jan 1, 1979

By Kyle T. Chomyn

Multi-disciplinary engineering analysis and advanced modeling techniques were used to identify and develop low cost design modifications to improve a blast furnace hot blast air distribution main that experienced frequent refractory failures. Piping flexibility analysis helped identify the root causes of refractory damage and determine the need for new expansion joints. Finite element analysis was used to optimize a custom-designed elbow-to-elbow tie-rod system, which ensures thermal expansion loads are not placed on connecting piping. Heat transfer coefficients through the elbows were estimated using computational fluid dynamics (CFD) flow modeling. The cast refractory design was changed to a more reliable brick refractory design. Excessive draft was occurring during furnace back-drafting, so the system was assessed using CFD, and a passive flow-reduction spool was designed. This firstprinciples engineering design approach allowed for optimization and verification, ensuring that the new design addressed the root cause of the previous deficiencies.

Aug 17, 2017

By Albert F. Duzy

Recently there have been some problems associated with hot coal in shipments from the USA to overseas markets. This paper will serve several functions. First, a brief review is presented, together with a selective bibliography. Second, a thorough discussion of coal oxidation is covered. Third, potential effects of storage are presented and, lastly, methods are suggested for the safe storage and bulk transfer of coal. The scope includes coal storage for power plants.

Jan 1, 1983

By M. Stephton, L. A. Cornish, R. Süss, N. B. Maledi, J. H. Potgieter, L. Chown

In today?s gas turbines, the emphasis is on saving energy and reducing the amounts of pollutants emitted. This can be attained only by designing alloys with higher melting points and the capability to retain mechanical integrity at increased temperatures. The development of nickel-based superalloys (NBSAs) has reached its limit, as the alloys are operating at critical temperatures close to their melting points. Further increase in the operating temperatures will result in dissolution of the strengthening phases and even melting. Recent trends are towards developing materials that are adequately strong but have much higher melting points and corrosion resistance than the NBSAs that are currently in use. Studies conducted on Pt alloys with similar structure to the NBSAs have presented mechanical results that are promising. This has led to further development of these alloys as a replacement for NBSAs. The operations of gas turbines are usually limited by hot corrosion, which could lead to catastrophic failures. Increased temperatures have an adverse effect on the corrosion of the alloys by making the environment more aggressive. Hence, during a material selection process, the corrosion behaviour of any selected material for a highly specialized application such as gas turbines needs to be assessed. Generally, coatings are applied to combat degradation by salt deposits, hence coated and uncoated NBSAs were selected as benchmark alloys. Corrosion mechanisms and kinetic studies of the Pt alloys were conducted. High temperature hot corrosion (HTHC) tests were conducted at 950°C for540 hours. Analysis of the corrosion products was conducted using a Raman spectrometer, scanning electron microscope with energy dispersive X-ray spectroscopy (EDS) optical microscopy, and X-ray diffraction study of the phases that formed. Both coated and uncoated NBSAs failed under the test conditions. Samples were covered with a porous non-adherent greenish layer which is characteristic of NiO. Pt alloys displayed superior corrosion properties compared with the benchmark alloys.

Jan 1, 2006

A commonplace, sometimes overlooked or taken for granted, article of everyday existence is the tin can. Produced from thin gauge low carbon steel, and commonly coated with a mere 60 millionths of an inch of pure tin, the product is however strong and corrosion resistant. Tin-plate serves a myriad of purposes-the most important being to meet the requirements of the canning industry. Australia's newest steel product, tin-plate, was first produced on a commercial scale during the early part of August, 1957. The commissioning of the Hot Dip Tinning Plant (Fig. 1) of The Broken Hill Proprietary Co. Ltd. at Port Kembla, marked the culmination of a proposal dating back to 1939, the advent of World War II having caused its deferment to the present time.Cornish tin is known to have been exported as early as 300 B.C. to Syria and tinned vessels existed even in the year A.D. 23. The tin coating of plate could be described as an ancient art, believed to have had its origin in Bohemia in the thirteenth century. During the next 450 years, the process spread through Saxony to Pontypool in Monmouthshire, but it was a further half century before any measure of success was obtained.Perhaps the two greatest milestones in tin-plate manufacture were the rolling of iron plates first carried out in 1728, thereby outmoding the hammer formed sheet, and more recently, the development of the electro-deposition process. By the nineteenth century, several important changes had arisen; namely, the substitution of steam for water power, coke for charcoal in the production of the base metal, and...

Jan 1, 1958

By Steven George Jansto

The hot ductility behavior of different microalloyed steel chemical compositions was examined simulating the thermal and strain conditions through the straightening or unbending section of the continuous casting machine. All samples were obtained from industrial slab casters ranging from 200 to 300 mm in slab thickness from steel mills throughout the world including China, Brazil, North America and Europe. The slabs were crack-free and hot rolled into prime quality products. No laboratory heats were tested. Although these microalloyed steels exhibit inherently lower hot ductility behavior, as measured by percent reduction in area at elevated temperature, these steels still exhibit sufficient ductility to satisfactorily meet the unbending stress and strain gradients existing in the straightening section of most casters. The majority of the published hot ductility data, as measured by % reduction in area (%RA), were based on laboratory heats and hence, are inaccurate in accessing the propensity for slab cracking on an industrial caster. This situation then results in invalid conclusions for different chemistries. This research has determined the minimum required %RA for crack-free casting is significantly lower than results based upon previously published laboratory generated data. For example, the literature quotes 40% RA minimum for Nb-bearing steels when in fact as low as 10% minimum RA is more than sufficient to assure crack-free casting based upon the extensive testing and analysis performed in this study. Instead of %RA, the measurement of strain energy has been introduced to evaluate hot ductility behavior. It is concluded that strain energy is a better measure of hot ductility behaviour than %RA. There is considerable value in the evaluation of the hot stress and strain curves, process metallurgy parameters and their relationship to slab quality instead of just basing hot ductility decisions on simple %RA measurements.

Aug 16, 2017

By A. Gakwaya, K. Ba, M. Guillot, J. Levesque

"In the aerospace industry, parts requiring tight dimensional tolerances and high mechanical properties are often produced by forging. This forming process allows for an optimal use of the material and can produce high quality parts at a reasonable cost. Thanks to CAD techniques, it is now easier to predict flow profiles and in-process defects occurrence as well as wear of the forging dies. However, in order to determine the properties of the forged part with computer simulation methods, a good material constitutive law is a prerequisite. This paper presents a virtual manufacturing process modeling for the closed die forging of a workpiece performed with Abaqus. The hot closed die forging is a regular process applied to manufacture metallic components used in aerospace industry. In this forming process, the material flow and final properties depend on the microstructure evolution during the process that is why it is important to include the microstructure effects in the material model. Based on the stress-strain data measured experimentally, the material parameters of the standard (classical) Johnson-Cook constitutive model and of a modified Johnson-Cook constitutive law including the microstructure effects have been determined. The obtained simulation results are compared with the experimental results for validation.INTRODUCTIONDue to their good physical and mechanical properties such as ductility, fatigue strength, corrosion resistance and rupture, aluminium alloys are often used in the aeronautic and the automobile industries. In this work, we present the forging of an Al-Zn-Mg-Cu alloy, a high strength aerospace alloy recognized for his good combination of physical and mechanical properties. The forging process is simulated in Abaqus Explicit using both the standard Johnson-Cook law (Johnson & Cook, 1983; Hor, 2011; Lin et al., 2012), and its modified version as proposed by Andrade et al., (1994). The Johnson-Cook law offers the advantage of considering the coupled effect of the plastic strain, the plastic strain rate, the temperature of forging and the hardening effect. However, it is a phenomenological model which does not account for the effect of the microstructure evolution. In this work, a modified Johnson-Cook model implemented in a user subroutine is used. It includes the effect of the dynamic recrystallization phenomenon during the hot deformation. The dynamic recrystallization has a noticeable influence on the microstructure and on the properties of the material. The term dynamic means that the process starts and acts during the deformation and this is different from the static mechanism of recrystallization which occurs during an annealing and after cold or hot deformation. Since properties of the alloy used in this work are not readily available in the literature then characterization tests have been done at various temperatures and strain rates, in order to determine the thermomechanical properties and the material behavior during the process of hot forming, more precisely during the hot forging process."

Jan 1, 2016

By P. M. Tyroler, W. J. Thoburn, M. R. Alberty

"An initial test of this unique application demonstrated that hot gunned refractory would adhere satisfactorily. Subsequently, it was found that the proportion of material sticking during application increased with increased vessel temperature and when a mix containing pitch was used. About 75 per cent of the latter type adhered when it was applied at 1600°C.TBRC availability increased from an historical average of 62.5 per cent to 64.7 per cent during four campaigns when hot gunning was routinely practiced. Refractory cost was about 20 per cent less than that anticipated without gunning. Average parameters per campaign with gunning ranged as follows: 90 to 108 heats, 10 to 37 applications and 1.4 to 2. 7 hours per application. Prior to gunning, the average number of heats per campaign was 73.IntroductionThe Top Blown Rotary Converter process at Inco's Copper Cliff Nickel Refinery converts copper-nickel-sulphur concentrates to a material suitable for carbonyl refining (1),(2).Operating conditions are particularly hard on refractory. Batch cycles finish at temperatures up to 1650°C, with occasional excursions over 1700°C. New heats are then usually initiated immediately and the refractory is subjected to intense thermal shock from the cold feed. Temperature cycles are also introduced three to four times during a heat when the process is interrupted for scrap charging, temperature measurement or sampling.Abrasion wear results from rotation of the converters at speeds up to 15 RPM and from agitation of the bath with supersonic-velocity oxygen. Mechanical damage also occurs when chunks of scrap or solid matte are processed. Chemical corrosion is also present, as we know from our own laboratory work(2) and reports of operations elsewhere. As a consequence, refractory material and installation form a very large proportion of the converter plant costs. Equally important is the loss of converter availability during rebricking; this significantly reduces plant capacity."

Jan 1, 1981

By Pedro Augusto David Machado

The hot metal produced in small blast furnaces runs with a highly heterogeneous charcoal. The result is a significantly higher hot metal chemical composition variation, especially for the silicon content, which varies from 0.4 to 1.5% in Mini Blast Furnaces - MBFs, designed to feed an EAF and/or a BOF. These MBFs operate with frequent variation in their productivities to feed preferably only one of the steelmaking reactors, that is, EAF or BOF. The hot metal suitable amount, chemical composition and temperature, to be delivered at the steelmaking vessel, become the major concerns in the integrated operation MBF to EAF or BOF. In order to cope with those undesirable frequent variations, a solution has been proposed based on the existing technologies of oxygen jets and ladle refining techniques adapted to a hot metal ladle or to a Torpedo Car. The proposed technique is not only able to adjust hot metal temperature and chemical composition, but it also generates the adequate conditions for refinement from P and S, as well as “cleaning” hot metal ladles and Torpedo Cars by melting pig iron skulls. Therefore, this new technique development results in high hot metal yield, an adequate chemical composition and bigger campaign of hot metal ladle.

Aug 17, 2017

By Michael W. Roper

McDermitt Mine is located in northern Humboldt County, Nevada, approximately 5 miles south of the Orgeon-Nevada line (Figure I), within the Opalite Mining District. The operation is a joint venture between Placer Amex Inc., San Francisco, and Mineral Exploration Company Ltd., a limited partnership. The McDermitt orebody possesses a discontinuous, gently dipping blanket-like form within 150 feet of the surface over an area 2200 by 2500 feet. The ore zone averages 20 feet in thickness. The ore minerals consist of cinnabar (HgS) and corderoite (Hg3S2C12) deposited parallel to bedding within argillized, Miocene age, tuffaceous lacustrine sediments. Exploration indicates reserves of approximately 3,000,000 tons ore at a grade of 10 pounds mercury per ton (0.5%) An open pit mining operation utilizing scrapers and bulldozers supplies a concentrator with 700 tons of ore per day. The milling operation consists of autogenous grinding, flotation concentration, concentrate dewatering, and tailing disposal, with a design capacity of 100 tons per hour. The furnace section consists of a concentrate filter, vertical six hearth furnace, mercury condensing system, and exhaust gas scrubbing systems. It has a design capacity of 1000 pounds of dry concentrate per hour. The McDermitt orebody is situated about 2000 feet north of the Cordero Mine which, with adjacent properties, produced over 115,000 flasks (76 pounds per flask) mercury from 1941 to 1972' Two other major mercury producers in the district have been the Bretz and Opalite Mines, located in southern Malheur County, Oregon, within 5 miles of the Oregon-Nevada line. Bretz and Opalite have produced about 14,800 and 12,370 flasks mercury respectively, from 1926 to 1965.1/

Jan 1, 1976

The completion of the Hot Strip Mill at the Port Kembla works of Australian Iron & Steel Ltd., makes possible the production of steel plates and wide strip of a quality and in quantities not possible previously in Australia, and will also enable the production of tinplate to be undertaken in this country.The site chosen for the mill was a mud fiat underlain by a hard stone bottom at 5, to 801 feet below the surface; and a total area of one hundred acres was reclaimed to a level of 20 feet above the original surface.Three adjoining buildings were constructed to house the slab receiving yard, mill equipment and electric drive, together with the plate finishing line.After slabs have been heated to 2250°F at a rate of 90 tons per hour, they are transferred to the vertical scale breaker which is the first stand in the hot roughing mill. Here the primary furnace scale is first cracked and then blasted off by high velocity water descaling sprays.The next stand is the horizontal scale l;Jreaker, where any remaining primary scale is broken and then blasted off. After descaling, the slabs pass to the broadside mill, where short slabs are turned and rolled on broad side for wide plate.The next step is a slab squeezer which squares up the edges after broadsiding ready for the reversing mill. This is the finishing stand for plate and the last roughing stand for strip, which then passes to the finishing mill.The hot strip finishing mill consists of six stands with a maximum finishing speed of 2,230 feet per minute. Strip is cooled for coiling by water sprays on a hot run table and then coiled on a mandrel type downcoiler, from whence coils of hot strip are weighed and transferred by conveyor to the coil storage building.Plates are transferred from the reversing mill to the plate finishing line where operations consist of levelling, inspection, branding, cutting to width and length:INTRODUCTIONDue'to the increasing production of cars, refrigerators, washing machines and similar consumer goods in Australia, together with the increased requirements of galvanised iron...

Jan 1, 1956