Search Documents

By C. F. Feng, L. Froyen

"In-situ processes have emerged as new and promising techniques for metal matrix composite fabrication. They offer significant technical and economic advantages over conventional processing. One of the in-situ processing routes that have been used is reactive free sintering of a mixture of powder reactants. However, materials synthesised via this route are always porous because of density differences between reactants and products. An example are the porous Al/(TiB2+Ah03) MMCs obtained by heating powder mixtures of Al+ Ti02+B with Ti02 and B in stoichiometric ratios for forming TiB2• In this study, porous Al/(TiB2+Ah03) composites were further processed by hot-pressing at temperatures above 600°C. This processing cycle was designed so that the composites could be densified. Furthermore, the reaction kinetics of the in-situ processing are studied by means of DSC analysis measured at different heating rates. The activation energies of the three intermediate steps that are involved in the reactive processing for preparing AV(TiB2+Alz03) MMCs are determined to be 923 kJ/mole, 241 kJ/mole and 235 kJ/mole respectively.XRD proved that the hot-pressed products consist of Al, TiB2 and Al203- Properties of the products are assessed by microstructural characterisation (LOM, SEM and EDS), microhardness, Young's modulus and bending tests. The results show that good microstructures, elastic properties and strengths, as well as acceptable ductilities were achieved. For the composition 79.74wt% Al-15.95wt% Ti0z-4.31wt% B, after the reactive free-sintering and hot-pressing cycles, Young's modulus is 105 GPa, bending strength is 509 MPa and maximum strain is 5.0%; for composition 88.73wt% Al-8.87wt% Ti0z-2.40wt% B, they are 89 GPa, 311 MPa and 8.2% respectively. It can be seen that the properties of products can be tailored by adjusting the relative amounts of reactants in green samples. Furthermore, for comparison reasons, Al and a binary system Al-Ti02 were identically processed as the ternary systems. Their microstructures and properties were studied."

Jan 1, 1998

By K. J. Richards

The converting of copper mattes to blister copper has seen few technical advances since the introduction of batch furnaces using submerged tuyeres over a hundred years ago. The first side-blown converting vessel, operated by P. Manhes in 1882, was an offshoot of the 'Bessemer steelmaking process, and subsequent improvements in the conversion of molten mattes resulted In the Peirce-Smith converter, still the Industry standard today. While Peirce-Smith' converting has served the industry well since the early 1900!s, increasingly stringent environmental regulations, burgeoning energy costs, and a trend toward continuous processing have set the stage for a major improvement in this area of copper production. In contrast to a growing number of approaches for continuous converting using molten copper mattes, Kennecott is developing a process for treatment of solidified matte which allows improved' control, higher oxygen enrichment and a separation or decoupling of smelting and converting operations not possible with the other converting technologies. The new process known as Solid Matte Oxygen Converting, or SMOC, eliminates the need for molten matte transfers, minimizes fugitive emissions, and produces high strength SO2 off gases which substantially reduce offgas handling requirements. The SMOC process, despite additional matte solidification and size reduction steps, offers both capital and operating cost advantages for new smelters and the upgrading of existing plants, when compared with conventional converting technologies. Capital cost reductions of up to 35% in converting, gas handling, and sulfur fixation are indicated. Kennecott has successfully tested the new process concept and continued' development work is now under way to commercialize the technology. This paper reviews the limitations of batch copper converting with emphasis on the need for a continuous process, previous industry approaches to continuous converting of molten mattes, and the new Kennecott development.

Jan 1, 1983

By A. K. Kyllo, N. B. Gray, B. N. McCurry

"Dynamic control of the formation of a solidified layer between a pipe wall and a flowing melt enables the flow rate to be adjusted in real time. This solidified layer can be generated by using a coolant on the outside of the pipe wall to remove the required heat. The coolant, and hence the solidified layer, can be controlled remotely. The dynamic behaviour of the solidified layer was investigated by both physical experiments and mathematical modelling. The mathematical model has been developed using a finite difference technique to describe conduction through the pipe wall and solidified layer. Results from the model were consistent with previous steadystate experimental results using molten lead. Experiments are currently being carried out using molten tin in a recirculating circuit with a cooling system that is instrumented for accurate computer control to validate the model. The circuit is designed for flowrates of up to 24 kg/s (86 tph) of molten tin. Steady-state and dynamic predictions were made for the current rig.Industrial SignificanceThe current method of choice for tapping slags, metals and mattes from many metallurgical furnaces is using an oxygen lance to open the taphole and using a clay plug to close it. There are, however, some significant drawbacks in this method. The heat generated by the oxygen lance erodes the refractory lining of the taphole, as well as the clay plug, and the furnace products themselves corrode the taphole. Using an oxygen lance is also a significant safety hazard to the operators as they must work in close proximity to the furnace and be subjected to a shower of sparks while opening the taphole. Also, the flowrate of material through the taphole cannot be controlled online as the diameter of the opening cannot be varied easily. This feature means that the level of product in a furnace cannot be kept constant."

Jan 1, 1999

By Y. A. Chang, J. Woodford, C. R. Kao

Reactive diffusion studies between NbC and Si were carried out at 1300 °C under a vacuum of 10-5 torr and a uniaxial pressure of 1 MPa. The annealing time ranged from 8 to 100 hours. The Si used was single crystal silicon; the NbC was hot-pressed powder compact. A NbSi2+SiC two-phase reaction layer formed with NbSi2 as the matrix and SiC as discontinuous particles. The microstructure of the reaction product is homogeneous, dense, and fine. The NbSi2 grain size and SiC particle size are in the micron range. The growth of the reaction products follows parabolic kinetics. Extrapolation of the data to zero thickness suggests an apparent incubation time of 3.5 hours. However, for short annealing time «60 hours), the thickness data can be approximated by linear kinetics with an initial growth rate of about 2 11m/hr. Based on these experimental observations, a growth mechanism for the reactive diffusion between Si single crystal and NbC powder compact is proposed. We propose that the nucleation sites for the SiC particles are at the voids of the NbC powder compact. This proposed nucleation mechanism offers a potential way of controlling the SiC particle size by changing the void size and void density of the NbC powder compact. This hypothesis, if proven to be true, will allow us to control mechanical properties of the composites by tailoring the SiC particles formed. It is also pointed out that the microstructure requires Si to be the dominant diffusing species and to diffuse through the reaction layer, while Nb and Conly have to undergo local rearrangement.

Jan 1, 1996

By Varuzan Kevorkijan

A new method for faster production of functionally graded metal-ceramic laminates is based on reactive pressureless counterflow infiltration/penetration of a ceramic substrate with two different metallic infiltrants. The porous or dense ceramic preform is pressurelessly infiltrated or penetrated from one side by the first metallic infiltrant to the desired cross section of the preform, producing the top layer made up of the solidified infiltrant and the underlayer consisting of reactive infiltrated preform. The partly infiltrated perform is then completely infiltrated starting from the other side by the second metallic infiltrant, in this way fabricating the internal layer, consisting of the ceramic perform infiltrated with the second infiltrant and the bottom layer formed by the solidified second infiltrant. Systems already investigated include carbide, nitride and boride ceramic performs infiltrated with aluminum and magnesium alloys.

Jan 1, 2003

By Serge Lavoie

Alcan's Guillaume-Tremblay plant, located in Jonquiere, Quebec, has been in operation since 1990. This was the first plasma dross processing plant ever built. In addition to the use of the plasma heating technology, Guillaume-Tremblay has other unique features making it a modern and efficient dross processing facility. This paper presents a general overview of the practical experience at the Guillaume-Tremblay plant. In particular, the utilization of plasma heating in industrial conditions, the metallurgical performance, the unique dross handling system, the control and information management system and the reclaiming of the by-products will be discussed. Finally, the use of the plasma process for salty dross will be addressed' briefly.

Jan 1, 1995

By Marco Olper

After two years of extensive research a new and innovative modification to the CX-EW process has been exploited. This process, called CX-EWS, avoids completely all the critical aspects of the previous process which affected the cost of the energy, of the chemicals and of The maintenance of the insoluble anodes. All these benefits reflect a saving of about 30% of The operating costs compared to the present traditional production and allow for a total operating costs of less than 6.5 cts/lb. lead (net of raw material cost). With this new technology it is allowed for the first time the treatment in the same plant facilities of both primary lead sulphide concentrate and spent batteries. The paper describes the technical and economical aspect of the new process with a feasibility study for 150,000 t/y spent battery facility throughput.

Jan 1, 1995

MODELLING FOR DESIGN AND CONTROL AT KALGOORLIE NICKEL SMELTER Modelling at KNS has been driven by a need to have better tools to answer questions about control, design and optimisation of the plant. This paper describes a number of modelling tools developed for use at KNS and how the development of modelling tools fits with a design and control strategy. In the area of control, a thermodynamic model has been developed to allow process parameters to be calculated. The model allows for the automatic selection of data from a laboratory data base, desired operating set points are input and the operating parameters are calculated. The model has the ability to adjust the burner efficiency and the furnace heat loss depending upon conditions. To assist with the testing of proposed furnace design changes, various mathematical models of the burner and shaft have been created using PHOENICS. These models are particularly well suited to combustion heat transfer and flow aspects of both the burners and shaft. Validation of these models have been based on novel sampling and measuring techniques in the shaft and also by using scale and cold models. Overall plant energy and cost structures can be analysed using a flowsheet simulation, developed to evaluate potential alterations to the plant flowsheet. This model system allows the global evaluation of process changes.

Jan 1, 1993

In accordance with the new concept described in the paper presented at the TMS annual meeting in 1989, 1 a new zinc cellhouse was constructed and successfully operated. The new concept was proposed in order to reduce energy requirements and to mechanize the electrode handling in the cellhouse. Major modifications involved the use of an electrode unit consistfog of assembled anodes and cathodes with frame bodies between each cathode and anode. The space between a cathode and an anode could be halved by this unit structure. In this paper actual operation data are summarized and discussed in comparison with the calculated figures.

Jan 1, 1990

By M. M. Kim

As-electrogalvanized coatings of pure Zn, Zn-11% Fe, and Zn-18% Fe coatings were characterized in terms of initial crystal structure and surface morphology. Samples were then subjected to heat treatments simulating the paint bake cycle of automobile manufacturers. Surface morphology changes were correlated with the process variables, and crystallo.graphic changes were interpreted by mapping heat treatment routes on the Fe-Zn phase diagram. The morphology of pure zinc electrogalvanized coatings with heat treatment from platelets to smeared platelets. The zn-11% Fe coating changes with heat treatment from tetrahedral nodules to a mixture of round and tetrahedral nodules, with the Zn-:18% Fe coating always having round nodules. Regarding crystal structure, a critical transformation time can be defined at any selected temperature, below which the crystal structure does not change. This temperature is related to iron content.

Jan 1, 1990

By Luis W. Pommier

Large quantities of sea sludge containing halogenated organic compounds, such as PCB, oils and metals like arsenic and lead have accumulated throughout the years at the bottom of sea channels and harbors and are obstructing navigation and creating environmental problems which need to be resolved. A sludge from a California port would be dredged by suction pumps, it would be processed in a plant which would be built either on firm soil or on floating platforms. The sludge shows contents of up to 1 ppm of PCB, 15 % oil and 10 ppm of arsenic, which generates a very fetid odor. Bench scale work indicates that most of the contamination concentrates on the solid phase, in fact, only minor amounts of oil report to the sea water and can be readily removed by physical means. After separation of the sea water from the solids of the sludge by decantation, it is possible to solubilize the PCB, the oil and the metals into an organic solvent leaving a non-hazardous soil for disposal near the harbor. The PCB is dehalogenated during the solubilization process leaving a liquor solution containing the oil and metals. The oil is extracted leaving an aqueous solution containing the arsenic. Further process extracts the arsenic from this solution rendering the liquid non-hazardous. Transportation and disposal of the sludge is impractical. There are hundreds of thousands of tons of hazardous soils accumulated in each harbor, which would fill the hazardous waste disposal sites available and it would be, prohibitively expensive to do so. It is not possible to compare the costs of decontamination with a competitive method. If it were, the proposed process would be less expensive than transportation and disposal and it has the advantage of removing the liabilities from the Responsible party. After a full scale continuous pilot project is run to decontaminate a small, 500 cubic yards accumulation of this type of sludge in a California harbor, a full scale environmental project would be initiated. The decontamination of one million tons of sludge would be completed in five years.

Jan 1, 1995

By Deyou Yin, Kongfang Feng, Bo Wang, Jieyu Zhang, Xin Hong, Shaobo Zheng, Jinyin Xie

"The flow patterns and mixing characteristics in a water model of C-H2 smelting reduction furnace are experimentally studied in this paper. Water modeling is employed to investigate the features of gas jet stirring and the fluid flow patterns in the bath of a smelting reduction furnace during the top, bottom, and side combined blowing process. The influence of the gas flow rate for top, bottom and side nozzles, angle, submerged depth of each side nozzles and the height of the top nozzle has been examined. It showed that the gas flow rate of side nozzles and bottom nozzle had a key role on the fluid flow and mixing characteristics. The gas jet from the top nozzle could change the agitation and fluid flow pattern caused by the gas jets from the side nozzles in the bath.IntroductionFacing the current natural resources decrease and the environmental degradation, smelting reduction iron-making technique is believed to be the most representative at present. Mid last century, the concept of producing liquid iron or semi-steel directly from ore fines and inexpensive fuel was the subject of considerable pilot plant development activity. Among these projects, the direct smelting process, which is the reduction and melting of iron-bearing materials by carbon and other hydrocarbons in the vessel containing a molten bath, is the most popular one. A number of direct smelting processes have been developed around the world, e.g. COREX, DIOS, HIsmelt, AISI, ROMELT, etc.These studies put forward a new technology, which through bottom nozzle blowing rich hydrogen, top nozzle blowing rich oxygen and provide preheating ore and solvent, side nozzles blowing oxygen-coal to realize smelting reduction iron-making process. Owing to the metallurgy reactions always in high temperature, which is above 1600 °C, it is difficult to visualize the mixing behavior and measure the desired phenomena in the reduction vessel. With water modeling, the primary advantages are that it is relatively easy to observe and measure the flow phenomena in the bath."

Jan 1, 2011

By A. Onozaki

The Iijima Refinery was put into operation in 1972 and today has an annual production capacity of 156,000 tons of SHG electrolytic zinc. At the Iijima Refinery, the recoveries of gold and silver are 98.0% and 98.2%, respectively. Gold contained originally in the zinc concentrates reports in the Cu-Pb-Ag residue produced in the residue treatment process. Silver contained in the concentrates is distributed between the Cu-Pb~Ag residue and the copper cake produced in the purification process. The Cu-Pb-Ag residue, which contains gold and silver, is sent to the Oyachi flotatfon plant of the Kosaka Smelter; about 82% of the gold and about 85% of the silver are recovered in the copper flotation concentrate.. In this paper, the distribution of gold and silver in the Iijima. Refinery is discussed and operational results of the Oyachi flotation plant are presented.

Jan 1, 1990

By Bror Nyrnan

Solvent extraction technology and equipment have been developed within Outokumpu since the early seventies. During this period altogether nine solvent extraction processes for molybdenium, zinc, rhenium, cobalt, nickel, calcium and magnesium have been commercially adopted in Outokumpu's metallurgical plants. During last years a new mixer-settler concept based on a "Vertical Smooth Flow" (VSF) principle has been developed. It has also been found to be a good method for copper solvent extraction, decreasing essentially the crud formation and the organic and aqueous entrainments.

Jan 1, 1994

By A. R. Udupa

The reduction roasting behavior of chalcopyrite has been investigated using various combinations of a desulfurizing agent, i.e., CaO or Na2CO3, and a reductant, i.e., CO, H2 or C. Using these, combinations the sulfur is removed from the mineral as CaS or Na2S rather than SO2 as is the case with conventional copper smelting and converting. The laboratory reduction ex¬periments were conducted using thermogravimetric analysis (TGA) and boat tests of mixed combinations of fine particulate reactants subjected to a continuous gas stream. The degrees of metallization were determined by both weight loss and chemical analysis methods and the products examined using optical and scanning electron microscopy and electron probe microanalysis. The percent reduction after one hour at 900°C ranged from 60% to 94%. From these data It was possible to provide postulations as to the controlling reduction mechanisms.

Jan 1, 1983

By Susanne Pignolet-Brandom

QEM*SEM is an automated scanning electron microscope/computer system that characterizes samples with regard to mineral modal abundances, mineral grain and particle sizes, mineral associations, and particle surface areas. Additional information, based on the classification of particles according to the area percentage of a mineral of interest, can be obtained for samples of particulates. QEM*SEM is capable of analyzing a wide variety of materials although it was originally developed for applications to the minerals industry.

Jan 1, 1988

By D. Y. Wang, G. Y. Sha, X. L. Shen, D. R. Gu

The study of the volatilization kinetics of zinc and lead in pellets made of zinc-leadbearing dust mixed with coal powder, in a nitrogen atmosphere and at a temperature range between 1100 °C and 1300 °C, shows that the reduction temperature has a significant effect on the volatilization rates of zinc and lead, and that both the particle size of the coal powder and the extra carbon content has no effect on the volatilization rates. The obtained activation energies for the volatilization of zinc and lead are 79.42kJ/mol and 88.74kJ/mol respectively. The volatilization rate of zinc is controlled by the reaction between the zinc oxide and carbon monoxide while that of lead is controlled by the lead evaporation reaction, and the diffusion of gaseous lead through the gas boundary layer covering the surface of the reduced liquid lead.

Jan 1, 2000

By Donald R. Sadoway

Molten salt electrolysis is a proven technology for the extraction of metals -- all the world's primary aluminum is produced in this manner. The unique properties of molten salts, also make them excellent media in which to treat a variety of forms of waste. Of special .note in this regard is electrolysis in molten oxides, a .concept put forward by. the author, initially as a ."clean technology" for producing primary metal. However, in the context of waste treatment, electroly-sis in molten oxides is a process offering the prospect of changing the. valence of dissolved heavy metals while making pure oxygen gas as the main by-product .Laboratory tests conducted at a temperature of 1550°C on chromate sludge dissolved in an melt composed of Al2O3 and MgO have confirmed electrochemical production of oxygen on a carbon-free anode.

Jan 1, 1996

By Katsuyoshi Tatenuma

"In order to mitigate the effect of global warming by preventing the accumulation of atmospheric CO2, a permanent fixation method of surplus CO2 as an insoluble mineral onto the sea bottom is proposed. As the proposed reduction method of atmospheric CO2, the concrete concept of this method is to form an insoluble carbonate mineral (CaCO3) by direct electrolysis of the seawater; Ca2++2HCO3 -+OH- ? ?CaCO3(insoluble)+CO3 2- (soluble)+H++H2O <not as coral reef reaction>, are directly disposed of itself onto the sea bottom. By this treatment, a concentration of carbonate is reduced in the section of superficial seawater, and therefore the absorption capacity of atmospheric CO2 increases depending upon the shift of chemical carbon equilibrium between the mass of superficial seawater and the atmosphere. As no additives are required, or no secondary waste are produced, the proposed method assuming as green-orientated, has possibility to resolve fundamentally the problem of global warming in a green orientate manner.IntroductionRecently, the amount of atmospheric CO2 has been exponentially increasing and it is a main greenhouse effect gas causing the global warming [1, 2]. The concentration of atmospheric CO2 has increased more than 30% (370ppm in 2001) during only last two centuries, therefore approximately 750 Gton-C of CO2 currently exist in the atmosphere, in which 180 Gton-C of CO2 are accounted for the increment during two centuries [1, 3, 4]. In order to avoid the progressive increase of CO2 global abundance, 3 Gton-C of the incrementing amount per year [4], have to be removed annually from the atmosphere."

Jan 1, 2008

By Dilip Banerjee

"This paper discusses the Advanced Technology Program (ATP)'s support over the last decade to the development and use of process modeling as a tool to address some of the challenges faced by the U.S. metal casting industries. A particular focus will be given to highlight how process modeling can be used to improve the manufacturability of components needed for high performance and critical applications. The challenges associated with the design and production of thin-walled, cast parts with intricate and complex internal geometries will be discussed. Modeling issues associated with the control of the final grain structure in the solidified parts will also be addressed. This paper will describe the advantages of using appropriate mathematical models for designing new alloys for use in various applications.Finally, the role that ATP has played in uplifting the U.S. technological base through partnerships with industry and academia in high-risk research in order to bring to market new and improved products for the broader benefit of the nation will be discussed.ATP's BackgroundIn the 1980s, U.S. industries were losing market share to low-cost, high-quality manufacturers from Asian countries. Corporate leaders and policy makers determined that in order to sustain and grow market share, U.S. industries needed to improve their competitiveness and productivity through product and process innovation. There was evidence that companies were systematically under-investing in leading-edgetechnologies and failing to complete the development of new technologies [l]. There were also arguments in academic circles that pointed to a potential market failure in the area of early-stage technological developments. These concerns provided impetus for creation of the Advanced Technology Program (ATP) within the National Institute of Standards and Technology through the Omnibus Trade and Competitiveness Act of 1988. Through a rigorously competitive, cost-shared partnership with industry, ATP fosters the development and broad dissemination of high-risk technologies that offer the potential for significant broad-based economic benefits to the United States."

Jan 1, 2004