Search Documents

By J. D. Miller

The effects of operating variables on water transport to the over- flow, classification of hydrophilic particles and the recovery of copper and molybdenum from a low-grade porphyry ore are presented. Recoveries of copper and molybdenum exceeding 90 percent at a grade of 8 percent Cu and 0.2 percent Mo were realized for minus 100 mesh (1 49 µm) material at retention times of less than 500 milliseconds. The rapid rate of flotation and the effective separation of fine particles for an air sparged hydrocyclone appear to be due to directed interaction of particles in a high force field with numerous freshly formed small bubbles. This interaction occurs in the swirl flow developed by the system and is analyzed in terms of collision and induction time phenomena.

Jan 1, 1982

By J. Bartrum

Kidston Gold Mines is a 14 000 tonnes per day rated operation located 280 kilometers west of Townsville in Queensland. The principle shareholder is Placer Development Limited. Kidston's orebody consists of 44.2 million tonnes graded at 1.79 g/t gold and 2.22 g/t silver. Production commenced in January, 1985, and despite a number of control, mechanical and electrical problems, each month has seen a steady improvement in plant performance to a current level of over ninety percent rated capacity.

Jan 1, 1985

By Marc. A. Meyers

The analysis of the phenomena involved in the determination of the compressive strength of iron-ore agglomerates leads to the identification of the important parameters. It is shown mathematically that the pellet rupture strength is proportional to the cross-sectional area. Fracture is initiated at the center of the pellets by the tensile stresses developed by the compressive loads normally to the compression axis. The variation in strength between individual pellets of identical composition and subjected to identical treatments is due to internal voids of varying sizes, that act as stress-concentration sites. Two novel testing procedures are proposed. The first consists of testing the pellets between two plates having three steel spheres each. This configuration simulates much better the environment actually encountered by the pellets. The second procedure consists of a thick-walled cylinder in which a piston penetrates; a large group of pellets is tested simultaneously, as the stress versus strain plot is being recorded. This latter test presents significant advantages over the conventional testing procedure; the main one is that one single test is sufficient to characterize the mechanical response of the pellets.

Jan 1, 1981

By C. B. Kettering

In the early operations of the Inspiration Consolidated Copper Company, which extended from 1914 to 1926, the ore as mined contained principally sulphide copper minerals, manly chalcocite (Cu2S), This ore was milled in a 20,000-ton concentrator and the copper was recovered as a flotation concentrate which, was smelted at the nearby plant of the I ternational Smelting and Refining Company. In those days no attempt was made torecovercopper from any oxide minerals present. As mining operations progressed it soon became evident that the proportion of oxide minerals present would steadily increase, and. it was realized that some method of treatment would have to be developed whereby copper could' be recovered from both oxide and. sulphide minerals contained in the ore. A research program was instituted and after some years of experimental and, pilot plant work a new hydro-metallurgical process was developed whereby it became possible to extract copper from both the oxide and. sulphide minerals in a single leaching operation. The solvent adopted consisted of a mixture of sulphuric acid and ferric sulphate,' Following dissolution, the dissolved copper would be recovered by electrolysis. Also in the process of electrolyzing, spent solutions of sulphuric acid, H2SO4, and. ferric sulphate, Fe2(SOk)3, would be regeneratede and. somade available for continuous reuse. The process appeared to be a success and the decision was made to build a full-sized leaching plant for the future treatment of I spiration mixed ore. Construction was started and the leaching plant was completed in 1926, With the start of ferric-sulphate leaching the Inspiration Concentrator was shut down and, with the exception of a few short time runs has not operated since that time. The ferric sulphate leaching process served. Inspiration well for some 30 years and during that time won a name for itself as a classic example of hydro-metallurgical treatment of mixed sulphide oxide ores. Originally the plant was designed. to process some 7,500 tons per day of a mixed ore containing about 1,2% copper, of which 60% was present as oxide and. 40% as sulphide, Down through the years various improvements were made for the purpose of increasing plant capacity and as well to change the limiting 'factor of sulphide-oxide ratio, The final result was a leaching capacity of 9,600 tons per day when treating a 1% copper ore with a reversal of the sulphide-oxide ratio to 60% sulphide and 40% oxide.

Jan 1, 1958

By J. D. Miller

The processing of residues derived from various operations in the mining and metallurgical industry for by-product recovery is becoming more prevalent. A principal target for by-product recovery is flue dust produced by conventional smelting operations. Flue dust from zinc smelters has been processed for many years for the recovery of cadmium (1,2). The cadmium recovery technique which consists of a selective sulfation roast, followed by a water leach and zinc dust cementation, produces a lead cake residue (see chemical analysis in Table I), which consists primarily of lead sulfate.

Jan 1, 1975

By R. J. Sweigard

Productive and beneficial use of reclaimed surface-mined land is a concern of industry, government, and the general public. An investigation was conducted of current mined-land planning practices to aid in the development of a procedure for evaluating postmining land use potentials. This investigation considered both the industry and public planning approach to mined-land planning and was based primarily upon three case studies conducted in various regions of the United States. The site planning process that was developed during the investigation is iterative in nature and has been designed specifically for the mining industry. It centers around preliminary studies and data collection, development of land use alternatives, and the evaluation of alternatives. Use of this process facilitates the evaluation of economic, environ- mental, and social impacts of postmining land use alternatives. In this paper, the process is presented along with a description of its development, application, and significance.

Jan 1, 1984

By R. A. Pimentel

Complying with reduced dust standards (i.e., less than 2.0 mg/m3) due to quartz levels that exceed 5 percent is presently a critical problem for many continuous mining sections. Results are presented of research which was performed to determine the factors causing high levels of respirable quartz dust and to identify the major contributors to operator exposure. It was found that the significant sources of quartz dust are the drilling of the roof and the mining of the roof, floor and rock bands. Both the miner and the bolter may be on a reduced standard, but compliance is easiest to achieve on the bolter for which improvements in maintenance and operator practices are usually sufficient. At the miner, the problem is more elusive. Research continues to identify operating and mining practices that contribute to the exposure..

Jan 1, 1985

By D. M. S. Bhatia

The intimate association of iron formation and massive sulfide deposits has been documented by many investigators (McAllister, 1960; Hutchinson, 1972). In a classic example of such an association four distinct facies (oxide, carbonate, silicate, and sulfide) were identified in an Algoma type iron formation occurring in Paleozoic rocks, but exhibiting physical features (banding) and chemical composition (SiO2 + A1203 + Fe2O3) typical of Precambrian iron formations. The geochemical variation of the iron formation was studied by analyzing 62 samples for Si, Al, Fe, P, S, and CO2. Following a model proposed by James (1954), the geochemical and mineralogical variation of the iron formation can be used as an excellent tool for the exploration of massive sulfide deposits.

Jan 1, 1981

By A. G. Ulsoy

In recent years there has been an Increasing Interest In the application of automatic control theory to mineral processing systems, and numerous applications of mineral process control have appeared in the literature. A general approach to the synthesis of mineral process control systems is presented. The first phase of the control system design consists of specifying the control objectives, process variables and their interactions; these topics will be discussed with specific reference to mineral processing. The second phase Is con¬cerned with selection of control strategies algorithms, instrumenta¬tion, and other components of the control system and is discussed at length. These concepts are then illustrated by a flotation control case study.

Jan 1, 1981

By J. R. Hunter

The present is rooted in the past. This is particularly true in the case of mining operations. Coal mining in the United Kingdom is considered an old Industry comprising today 246 Coal Mines many of which have worked coal reserves in their locality for over 100 years. More than half the current producing mines lie in the Yorkshire and Midlands coalfields. They are in the oldest age group and produce 70% of the Industry's output. Some 50% of the remaining U.K. workable reserves amounting to approximately 98,000 million tons are still available to these regions. Fig. 1 Over the past two decades a gradual erosion of demand for coal in the U.K. has virtually halved the Industry's capacity. The number of Mines has reduced by 53% during the past 10 years. Productivity has increased by some 42% mainly through improvements in the central coalfields which has enabled costs to remain broadly competitive with oil.

Jan 1, 1976

By James G. Mock

The choice of equipment to be applied to a given installation by the Application Engineer begins with the data as presented to him by the user. This point in the relationship establishes a communication link, which will decide whether or not the correct piece of Overhead Equipment is applied at the most economic advantage to the user. The role played by the user cannot be minimized. No one knows better than he, just what work he expects to accomplish with this piece of machinery. However, all too often, he oversimplifies the requirements, and along with minimal crane and building parameters, merely refers to one of the following crane classifications as defined by The Crane Manufacturing Association of America, as shown in Figures 1, 2, 3, 4, 5, 6 and 7. This approach places the ultimate user in an unfair position, since he has then assumed the status of the machinery designer and must, therefore, assume the responsibility of the success or failure of the operation of that piece of machinery. If the user selects a Class "C" crane for his job requirement, when actually a Class "B" crane can adequately handle the work load, he is not offering the most economic solution to his company and added little to the cranes service capabilities.

Jan 1, 1973

By R. N. Edwards

The Magnetometsic Resistivity (MMR) method is based on the measurement of the low-level, low-frequency magnetic fields associated with non-inductive current flow in the earth. The traditional resistivity method maps the electrical properties of the earth by measuring the electric field caused by galvanic current flow between a pair of current electrodes. The MMR method differs from it in that the potential electrodes are replaced by a sensitive coil or magnetometer and a component of the magnetic field due to the current flow is recorded. The presence of an inhomogeneity redistributes the current flow which results in a perturbation of the electric field and, usually, of the magnetic field. The electric field immediately above a relatively conductive inhomogeneity must, by Ohm's Law, be smaller than that expected for a uniform earth. The current density in this region is also reduced but the current density within the inhomogeneity itself is enhanced so that the horizontal component of the magnetic field measured above the inhomogeneity is usually larger than that expected for a uniform earth. A method of interpretation using the magnetic anomaly was patented by Jakoskyl in 1933 but it met with little success at that time. Part of the problem was undoubtedly with the instrumentation, and only recently have robust instruments of sufficient sensitivity been developed2 and field data of good quality obtained. There are many common configurations of the potential and current electrodes in the resistivity method. Similarly, in the MMR method one or both current electrodes may be moved with the magnetometer, either horizontally or vertically ( in a bore-hole), or the current electrodes may be maintained in fixed positions and the magnetometer alone moved. The MMR anomaly is defined as the difference between the

Jan 1, 1975

By G. Reed Marchant

The control systems engineer is often faced with the problem of designing tests or experiments where the cost of obtaining information is expensive. This is true in aerospace as well as in process industries. In these situations the details of test design should be carefully evaluated before any test is executed so that the maximum amount of information is obtained for the effort expended. In recent years there has been a steady trend towards increased automation, In the process industries this has resulted in extensive review of process variables and, instrumentation techniques, development of more accurate system mathematical models, and extensive investments in complex control system as well as completely automated plants. When planning and developing these systems, where each measure of a process variable is usually expensive, it behooves the design engineer to give considerable thought to the details of test design before instrumentation is procured and installed so that the maximum amount of information can be obtained for the expense incurred.

Jan 1, 1968

By Eudes Prado Lopes

The Mineral Resource Exploration Company - CPRM - a part-private, part-government concern jurisdictioned to the Ministry of Mines and Energy of Brazil, was founded in 1969 for the purpose of promoting the exploration of mineral and hydric resources throughout Brazil. The political-administrative framework within which it was conceived and created considering that an economic and financial balance to be maintained in all its fields of activity, CPRM set out right from the start to organize itself to perform -three basic lines of action, which can be summarized as follows: As a Service Company, to carry out those services requested by government agencies and by the private sector through of service contracts; As a Mining Company under the Brazilian Mining Code, aiming at supplementing private initiative, not beyond the field of mineral exploration;

Jan 1, 1975

By Raymond K. Will

Computers are becoming increasingly valuable tools in the mining industry as a greater variety of appropriate hardware and software becomes available, combined with greater acceptance by management, Within a given time period an engineering staff can evaluate or design a project to much greater detail and higher accuracy by utilizing computers once suitable programs have been developed. We are all aware that throughout the world the decreasing grade of minerals coupled with increasing waste to ore ratios necessitate larger capacity, longer term mining operations and attendant higher capital costs. Computers can be of assistance in all stages of mineral exploitation, from geologic exploration through mine feasibility studies and design, to marketing and transportation. Because of the high speed with which data can be digested and manipulated by computers, preliminary information from any stage of investigation can be analyzed to assist in further guidance of that stage. By use of preliminary mine feasibility studies, financial forecasts and sensitivity analysis, even information from a far-removed phase such as marine transportation of the product, can help guide the exploration phase to a realistic target.

Jan 1, 1973

By K. L. Purdy

Electron spectroscopy for chemical analysis (ESCA) was used to determine the-surface characteristics of products from operating Pb-Zn-Cu concentrators on the New Lead Belt of southeast Missouri and pure galena and sphalerite samples treated-with flotation reagents in concentrations similar to those used in the mills. The emphasis was on the action of surface modifiers such as Na2Cr207, starch, SO2, CuSO4 and NaCN in sphalerite flotation and in the galena-chalcopyrite separation. The objective of the investigation was to monitor the relative oxidation states of the mineral and reagent constituents and correlate these surface concentrations and oxidation states with flotation theory and practice. ESCA was able to follow the action of all the modifiers except NaCN. The existence of PbCrO4 on the surface of galena conditioned with Na2Cr207 was verified. The Pb in the bulk PbS-CuFeS2 scavenger concentrate was found to be significantly more oxidized than the Pb in the bulk PbS-CuFeS2 rougher concentrate. ESCA was found to be most useful for investigating the actions of modifiers rather than collectors due to the large amounts of sulfur and background carbon already present on the mineral surfaces. After calibration for the particular chemical system of interest, ESCA can yield semi-quantitative analyses of the oxidation states of many elements (except hydrogen, and helium) present in the outer 10 to 25 A of a sulfide mineral surface.

Jan 1, 1975

By R. Bhaskar

The control of respirable dust in mines has been given paramount importance due to the health and safety implications associated with fine dust. The understanding of the temporal and spatial behavior of dust has been recognized as essential for increasing the efficiencies of the existing control techniques and for developing new control strategies. Mining-related studies in this area are, in general, limited. They are also mostly experimental. Some mathematical and computer analyses have been attempted. In this paper, first a review of the mathematical studies performed in the last three decades in this area is presented. Second, a mathematical model for analyzing dust flow in mines is proposed. The model takes into account a number of factors affecting dust transport. It incorporates varying dust generation source strengths and dispersion, deposition, and coagulation of dust in mine airways. Finally, application areas for the model are discussed. A computer program based on the mathematical model has been developed. The program will output the dust concentration in the mine atmosphere as a function of time and distance from the source. The amount of dust deposited on the sides, roof, and floor of the airway is also determined.

Jan 1, 1985

By J. H. Adkins

The goal of the project reported in this paper was to make recommendations for changes in roof bolting procedures and bolter design that would reduce roof bolter accident rates. To that end the project identified the major hazards associated with each task a roof bolter operator per-forms, normalized task accident frequencies. by the time spent on each task, reviewed equipment design features and operating procedures related to the identified hazards and developed recommendations for equipment and procedural changes that would reduce, if not eliminate, the hazards. The research steps completed during the project were: a. A review of related literature and re-search including roof bolting time studies b. The collection and analysis of 1975 accident data pertaining to roof bolter activities c. The normalization of the accident frequency data on the basis of time/task data d. A review of roof bolting equipment e. The development of a field data collection instrument f. The selection of mines for bolter observations g. The collection of field data h. Data analysis and problem specification i. The development of recommendations for corrective measures

Jan 1, 1978

By Robert D. Brown

The purpose of this paper is to tell a story - and it is a story with a moral. My topic is Present Trends in the Tax Environment Affecting Mineral Development in Canada, and the first thing to recognize is that, with depressed metal prices and weakening western economies, taxes, in and of themselves, are not really the cause of the Canadian mining industry's present doldrums. But the character and level of mining taxes in Canada has had a profound influence on the development of the industry over the past decade, and the expectations of what taxes the industry will face in future years will influence the industry's further growth. My theme today is that, in Canada, our tax system has, in the past, served as a negative and destabilizing influence in the mining industry: it has contributed to a major short-fall in investment commitments and hence in the contribution which the mining industry can make to the Canadian economy, and the adverse effect on the industry of previous high tax rates was made far worse by the confusing, contradictory and perverse nature of the tax system itself. This is a story with some happy parts in it, and, in fact, governments in Canada did learn, haltingly and grudgingly, that there are limits on the amounts that governments could safely extract from the industry, and that some assurances of long term fiscal stability were necessary if investors were to be induced to make massive commitments which could only be recovered over very lengthy periods.

Jan 1, 1982

By R. F. Pearce

The paper in based on laboratory and pilot plant investigations which led to the development of a series of processes for production of high purity metals from nickel-copper-cobalt mattes of a wide range of composition. The selection of ammonia pressure leaching or acid pressure leaching for various mattes is discussed. This is followed by discussion of various methods for leach solution purification and metal separation. The metals of high purity are produced by reduction with hydrogen from purified solutions. Examples are given of complete flowsheets for a number of mattes. Drawing upon those examples, general principles for the selection of the most suitable treatment process for particular material are outlined. Under certain circumstances, those processes may replace part of the pyrometallurgical treatment and all of the electrolytic refining steps which are customary in the treatment of nickel-copper-cobalt mattes.

Jan 1, 1959